Microbial diversity and dynamics in multi- and single-compartment anaerobic bioreactors processing sulfate-rich waste streams

We investigated bacterial and archaeal community structures and population dynamics in two anaerobic bioreactors processing a carbohydrate- and sulfate-rich synthetic wastewater. A five-compartment anaerobic migrating blanket reactor (AMBR) was designed to promote biomass and substrate staging, which partially separates the processes of methanogenesis and sulfidogenesis in the middle and outer compartment(s) respectively. The second reactor was a conventional, single-compartment upflow anaerobic sludge blanket (UASB) reactor. Both reactors, which were seeded with the same inoculum, performed well when the influent chemical oxygen demand (COD)/SO(4) (2-) mass ratio was 24.4. The AMBR performed worse than the UASB reactor when the influent COD/SO(4) (2-) mass ratio was decreased to 5.0 by raising the sulfate load. Terminal restriction fragment length polymorphism analyses of bacterial 16S rRNA genes showed that the increase in sulfate load had a greater impact on bacterial diversity and community structure for the five AMBR compartments than for the UASB reactor. Moreover, bacterial community profiles across AMBR compartments became more similar through time, indicating a converging, rather than a staged community. While similar populations were abundant in both reactors at the beginning of the experiment, fermenting bacteria (clostridia, streptococci), and sulfate-reducing bacteria became more abundant in the AMBR, after shifting to a higher sulfate load, while a novel Thermotogales-like population eventually became predominant in the UASB reactor. A similar shift in the community structure of the hydrogenotrophic methanogens in the AMBR occurred: representatives of the Methanobacteriaceae out-competed the Methanospirillaceae after increasing the sulfate load in the AMBR, while the archaeal community structure was maintained in the UASB.     

Treatment of strong domestic sewage in a 96 m3 UASB reactor operated at ambient temperatures: two-stage versus single-stage reactor

A 96 m3 UASB reactor was operated for 2.5 years under different conditions to assess the feasibility of treating strong sewage (COD(tot) = 1531 mg/l) at ambient temperatures with averages of 18 and 25 degrees C for winter and summer respectively. During the first year, the reactor was operated as a two-stage system at OLRs in the range of 3.6-5.0 kg COD/m3 d for the first stage and 2.9-4.6 kg COD/m3 d for the second stage. The results of the first stage showed average removals of 51% and 60% for COD(tot) and COD(ss) respectively without significant effect of temperature. The second stage reactor was unstable. The temperature affected sludge stabilization. During the second year, the first stage was operated as a single-stage UASB reactor at half of the previous loading rates. The results showed an average removal efficiency of 62% for COD(tot) during summer, while it dropped to 51% during wintertime. However, the effluent suspended solids were stabilized with VSS/TSS ratio around 0.50 all over the year. The sludge in the single-stage reactor was well-stabilized and exerted an excellent settlability. During the last three months of research, sludge was discharged regularly from the single-stage UASB reactor. The results showed no significant improvement in the performance in terms of COD(tot). Based on the results of the experiment, a single-stage UASB reactor operated at relatively long HRT is preferred above two-stage system at the Jordanian conditions.     

Organic loading rate and food-to-microorganism ratio shape prokaryotic diversity in a demo-scale up-flow anaerobic sludge blanket reactor treating domestic wastewater

We investigated the microbial community in an up-flow anaerobic sludge blanket (UASB) reactor treating domestic wastewater (DW) during two different periods of organic loading rate (OLR) and food-to-microorganism (F/M) ratio. 16S rDNA clone libraries were generated, and quantitative real-time PCR (qPCR) analyses were performed. Fluctuations in the OLR and F/M ratio affected the abundance and the composition of the UASB prokaryotic community, mainly at the species level, as well as the performance of the UASB reactor. The qPCR analysis suggested that there was a decrease in the bacterial cell number during the rainy season, when the OLR and F/M ratio were lower. However, the bacterial diversity was higher during this time, suggesting that the community degraded more diversified substrates. The diversity and the abundance of the archaeal community were higher when the F/M ratio was lower. Shifts in the methanogenic community composition might have influenced the route of methane production, with methane produced by acetotrophic methanogens (dry season), and by hydrogenotrophic, methylotrophic and acetotrophic methanogens (rainy season). This study revealed higher levels of bacterial diversity, metabolic specialization and chemical oxygen demand removal efficiency of the DW UASB reactor during the rainy season.     

The inhibitory effects and removal of dieldrin in continuous upflow anaerobic sludge blanket reactors

The inhibitory effects and removal efficiency of dieldrin (DLD) in anaerobic reactors were investigated. Anaerobic toxicity assay (ATA) experiments conducted in batch reactors revealed that 30 mg/l DLD had inhibitory effects on the unacclimated mixed anaerobic cultures. Continuous reactor experiments performed in a lab-scale two-stage upflow anaerobic sludge blanket (UASB) reactor system which was fed with ethanol as the sole carbon source, indicated that anaerobic granular cultures could be successfully acclimated to DLD. Chemical oxygen demand (COD) removal efficiencies were 88-92% for the two-stage system. The influent DLD concentration of 10 mg/l was removed by 44-86% and 86-94% in the second stage and overall UASB system, respectively. Biosorption of DLD on granular anaerobic biomass was found to be a significant mechanism for DLD removal in the UASB system. The maximum DLD loading rate and minimum HRT achievable for the first stage UASB reactor were 0.5 mg/lday (76 microg DLD/g VSS.day) and 10 h, respectively, which resulted in the overall COD removal efficiency of 85%.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD_soluble/ COD_total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes. The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82% and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite similar % COD in the particulate form in the synthetic and the real wastewater, the two wastewaters were selected for different microbial communities. Prominent DGGE bands of Bacteria and Archaea were purified and sequenced. The 16S rRNA gene sequences of the dominant archaeal bands found in the inoculum, and UASB sludge fed with raw sewage, CEPS pretreated wastewater, and synthetic sewage were closely associated withMethanosaeta concilii. In the UASB sludge fed with synthetic sewage, another dominant band associated with an uncultured archaeon 39-2 was found together withM. concilii.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD soluble/COD total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes.The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82%and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite similar % COD in the particulate form in the synthetic and the real wastewater, the two wastewaters were selected for different microbial communities. Prominent DGGE bands of Bacteria and Archaea were purified and sequenced. The 16S rRNA gene sequences of the dominant archaeal bands found in the inoculum, and UASB sludge fed with raw sewage, CEPS pretreated wastewater, and synthetic sewage were closely associated with Methanosaeta concilii. In the UASB sludge fed with synthetic sewage, another dominant band associated with an uncultured archaeon 39-2 was found together with M. concilii.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD soluble/ COD total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes. The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82% and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite     

Anaerobic treatment of a chemical synthesis-based pharmaceutical wastewater in a hybrid upflow anaerobic sludge blanket reactor

In this study, performance of a lab-scale hybrid up-flow anaerobic sludge blanket (UASB) reactor, treating a chemical synthesis-based pharmaceutical wastewater, was evaluated under different operating conditions. This study consisted of two experimental stages: first, acclimation to the pharmaceutical wastewater and second, determination of maximum loading capacity of the hybrid UASB reactor. Initially, the carbon source in the reactor feed came entirely from glucose, applied at an organic loading rate (OLR) 1 kg COD/m(3) d. The OLR was gradually step increased to 3 kg COD/m(3) d at which point the feed to the hybrid UASB reactor was progressively modified by introducing the pharmaceutical wastewater in blends with glucose, so that the wastewater contributed approximately 10%, 30%, 70%, and ultimately, 100% of the carbon (COD) to be treated. At the acclimation OLR of 3 kg COD/m(3) d the hydraulic retention time (HRT) was 2 days. During this period of feed modification, the COD removal efficiencies of the anaerobic reactor were 99%, 96%, 91% and 85%, and specific methanogenic activities (SMA) were measured as 240, 230, 205 and 231 ml CH(4)/g TVS d, respectively. Following the acclimation period, the hybrid UASB reactor was fed with 100% (w/v) pharmaceutical wastewater up to an OLR of 9 kg COD/m(3) d in order to determine the maximum loading capacity achievable before reactor failure. At this OLR, the COD removal efficiency was 28%, and the SMA was measured as 170 ml CH(4)/g TVS d. The hybrid UASB reactor was found to be far more effective at an OLR of 8 kg COD/m(3) d with a COD removal efficiency of 72%. At this point, SMA value was 200 ml CH(4)/g TVS d. It was concluded that the hybrid UASB reactor could be a suitable alternative for the treatment of chemical synthesis-based pharmaceutical wastewater.     

Potentials of anaerobic treatment for catalytically oxidized olive mill wastewater (OMW)

The catalytically oxidized olive mill wastewater (OMW) was subjected to continuous anaerobic treatment using two treatment schemes. The 1st step in both schemes was an up-flow anaerobic sludge blanket (UASB) reactor (2 0 l). The 2nd step was either a hybrid UASB reactor or a classical one (1 0 l, each). The 1st stage was operated at constant hydraulic retention time (HRT) of 24 h. The organic loading rate (OLR) varied from 3.4 to 4.8 kgCOD/m³ d depending on the quality of the pretreated wastewater. The results obtained indicated that, the 1st step UASB reactor achieved a COD percentage removal value of 53.9%. Corresponding total BOD₅ and TSS removal were 51.5% and 68.3%, respectively.The results obtained indicated that the hybrid UASB reactor as a 2nd step produced better quality effluent as compared to the classical one. This could be attributed to the presence of the packing curtain sponge with active biomass in the sedimentation part of hybrid UASB reactor which minimizes suspended solids washout, consequently enhancement of the efficiency of the reactor.Available data showed that a two stage system consisting of a classical and a hybrid UASB reactor operated at a total HRT of 48 h and OLR of 2.0 kgCOD/m³ d provided promising results. Removal values of COD_total, BOD_5 total, TOC, VFA, oil and grease were 83%, 84%, 81%, 93% and 81%, respectively. Based on the available data, the use of a two stage anaerobic system consisting of a classical UASB reactor followed by a hybrid UASB as a post-treatment step for catalytically oxidized OMW is recommended.     

Reactive red azo dye degradation in a UASB bioreactor: Mechanism and kinetics

Textile industry uses azo dyes in its processes, which are complex organic molecules that are not easy to be degraded. Reactive dyes are especially difficult to remove from wastewater because of the characteristics of the molecule: one or more azo bonds, naphthalene‐disulfonate, triazine or chloro‐triazine, and phenyl‐amine groups. The degradation of the azo dye reactive red 272 was studied under anaerobic conditions in a hybrid Upflow Anaerobic Sludge Bed reactor (UASB) with an activated carbon bed. An adapted consortium of microorganisms was used in the kinetic study (batch) and to inoculate the UASB reactor. The experimental design identified the main factors determining the dye reduction efficiency are the initial concentration of dye and dextrose (as electron donor) and the residence time in the reactor. Dye reduction rate was decreased as the concentration increases in the wastewater; as a result, a kinetic model with a change from first to second order is proposed. The kinetic study showed that the process is first abiotic (adsorption) and then biotic (biodegradation).     

High rate treatment of terephthalic acid production wastewater in a two-stage anaerobic bioreactor

The feasibility was studied of anaerobic treatment of wastewater generated during purified terephthalic acid (PTA) production in two-stage upflow anaerobic sludge blanket (UASB) reactor system. The artificial influent of the system contained the main organic substrates of PTA-wastewater: acetate, benzoate, and terephthalate. Three parallel operated reactors were used for the second stage, and seeded with a suspended terephthalate degrading culture, with and without additional methanogenic granular sludge (two different types). The first stage UASB-reactor was seeded with methanogenic granular sludge. Reactors were operated at 37 degrees C and pH 7. During the first 300 days of operation a clear distinction between the biomass grown in both reactor stages was obtained. In the first stage, acetate and benzoate were degraded at a volumetric loading rate of 40 g-COD/L . day at a COD-removal efficiency of 95% within the first 25 days of operation. No degradation of terephthalate was obtained in the first stage during the first 300 days of operation despite operation of the reactor at a decreased volumetric loading rate with acetate and benzoate of 9 g-COD/L . day from day 150. Batch incubation of biomass from the reactor with terephthalate showed that the lag-phase prior to terephthalate degradation remained largely unchanged, indicating that no net growth of terephthalate degrading biomass occurred in the first stage reactor. From day 300, however, terephthalate degradation was observed in the first stage, and the biomass in this reactor could successfully be enriched with terephthalate degrading biomass, resulting in terephthalate removal capacities of 15 g-COD/L . day. Even though no single reason could be identified why (suddenly) terephthalate degradation was obtained after such a long period of operation, it is suggested that the solid retention time as well the prevailing reactor concentrations acetate and benzoate may have played an important role. From day 1 of operation, terephthalate was degraded in the second stage. In presence of methanogenic granular biomass, high terephthalate removal capacities were obtained in these reactors (15 g-COD/L . day) after approximately 125 days of operation. From the results obtained it is concluded that terephthalate degradation is the bottleneck during anaerobic treatment of PTA-wastewater. Pre-removal of acetate and benzoate in staged bioreactor reduces the lag-phase prior to terephthalate degradation in latter stages, and enables high rate treatment of PTA-wastewater.     

Effect of sulfur source on the performance and metal retention of methanol-fed UASB reactors

The effect of a sulfur source on the performance and metal retention of methanol-fed upflow anaerobic sludge bed (UASB) reactors was investigated. For this purpose, two UASB reactors were operated with cobalt preloaded granular sludge (1 mM CoCl2; 30 degrees C; 24 h) at an organic loading rate (OLR) of 5 g COD.L reactor(-1).d(-1). One UASB reactor (R1) was operated without a sulfur source in the influent during the first 37 days. In this period the methanol conversion to methane remained very poor, apparently due to the absence of a sulfur source, because once cysteine, a sulfur-containing amino acid, was added to the influent of R1 (day 37) a full conversion of methanol to methane occurred within 6 days. The second reactor (R2) was operated with sulfate (0.41 mM) in the influent during the first 86 days of operation, during which no limitation in the methanol conversion to methane manifested. Cobalt washed out from the sludge at similar rates in both reactors. The leaching of cobalt occurred at two distinct rates, first at a high rate of 22 microg.g TSS(-1).d(-1), which proceeded mainly from the exchangeable and carbonate fraction and later at a relatively slow rate of 9 mug.g TSS(-1).d(-1) from the organic/sulfide fraction. This study showed that the supply of the sulfur source L-cysteine has a pronounced positive effect on the methanogenic activity and the retention of metals such as iron, zinc and molybdenum.     

Controlled shear affinity filtration (CSAF): a new technology for integration of cell separation and protein isolation from mammalian cell cultures

Up-flow anaerobic sludge blanket (UASB) reactors are being used with increasing regularity all over the world, especially in India, for a variety of wastewater treatment operations. Consequently, there is a need to develop methodologies enabling one to determine UASB reactor performance, not only for designing more efficient UASB reactors but also for predicting the performance of existing reactors under various conditions of influent wastewater flows and characteristics. This work explores the feasibility of application of an artificial neural network-based model for simulating the performance of an existing UASB reactor. Accordingly, a neural network model was designed and trained to predict the steady-state performance of a UASB reactor treating high-strength (unrefined sugar based) wastewater. The model inputs were organic loading rate, hydraulic retention time, and influent bicarbonate alkalinity. The output variables were one or more of the following, effluent substrate concentration (Se), reactor bicarbonate alkalinity, reactor pH, reactor volatile fatty acid concentration, average gas production rate, and percent methane content of the gas. Training of the neural network model was achieved using a large amount of experimentally obtained reactor performance data from the reactor mentioned above as the training set. Training was followed by validation using independent sets of performance data obtained from the same UASB reactor. Subsequently, simulations were performed using the validated neural network model to determine the impact of changes in parameters like influent chemical oxygen demand (COD) concentration and hydraulic retention time on the reactor performance. Simulation results thus obtained were carefully analyzed based on qualitative understanding of UASB process and were found to provide important insights into key variables that were responsible for influencing the working of the UASB reactor under varying input conditions.     

Extending the diffuse layer model of surface acidity constant behaviour: II. Estimation of intrinsic acidity and electrolyte ion site binding constants

Abstract

The main objective of this work was to study the capacity of bioaccumulation of copper in an upflow anaerobic sludge blanket (UASB) reactor, for the treatment of acid mine drainages (AMD). UASB reactor of 0.8 L was fed with sodium acetate, the organic loading rate (OLR) was set at 2.0gCOD/Ld, and experiments were performed in the reactor during 115 days. After 30 days, the COD removal efficiency was 90%. In the stationary stage, the higher production methane was 0.253 L/Ld. The reactor was added with 20 mgCu(II)/L during 30 days. The copper bioaccumulation was 98% and it was accumulated gradually in sludge until reaching a 61.6 mgCu(II)/gTS. The toxicity study demonstrated that the copper concentration at which the level of specific methanogenic activity (SMA) of the biogranules was reduced to 50% of the control (IC₅₀), was 280 mgCu(N)/L     

Multi stage high rate biomethanation of poultry litter with self mixed anaerobic digester

A multi stage high rate biomethanation process with novel self mixed anaerobic digester (SMAD) was developed in the present study to reduce the hydraulic residence time (HRT), increase the volatile solids (VS) loading rate, improve the VS destruction efficiency and enhance the methane yield. Specific design features of SMAD were useful in mixing the digester contents without consuming power and de-alienated the problem of scum formation. In the first phase, poultry litter having 10% total solids (TS) was subjected to high rate biomethanation in multi stage configuration (SMAD-I and II in series with UASB reactor). It was observed that gross VS reduction of 58%, gross methane yield of 0.16 m³ kg⁻¹ (VS reduced) and VS loading rate of 3.5 kg VS m⁻³ day⁻¹ at HRT of 13 days was obtained. In the second phase SMAD-II was bypassed from the process scheme keeping the other parameters same as in the first phase. The results obtained were not as encouraging as in the first phase. The study showed that multi stage configuration with SMAD design improved the anaerobic digestion process efficiency of poultry litter.     

Anaerobic and aerobic biodegradation of chlorophenols using UASB and ASG bioreactors

Chlorophenol degradation was studied by combined anaerobic–aerobic treatments as a single or multi-substrate system. 2,4-Dichlorophenol (2,4-DCP) was degraded to the extent of 52 and 78% in up-flow anaerobic sludge blanket (UASB) and aerobic suspended growth (ASG) reactors respectively, at organic loading rates of 0.18kg/m³/day and hydraulic retention time of 26.4h in the presence of glucose. The UASB represents the dominating facultative anaerobic microbial population. When the effluent from the anaerobic reactor (UASB) was subjected to aerobic treatment on the ASG reactor, 2,4-DCP and COD removals of 86 and 95% respectively were achieved. Aerobic degradation of chlorophenol by acclimated mixed bacterial isolates was found to be sequential: 2-Chlorophenol (2-CP) and 4-CP were degraded first, followed by 2,4-DCP and 2,4,6-Trichlorophenol (2,4,6-TCP) while the contrary was obtained in anaerobic degradation. In anaerobic degradation by acclimated mixed bacterial cells, 2,4-DCP and 2,4,6-TCP were degraded first followed by mono-chlorophenols. The anaerobic/aerobic bioreactors were most efficient when operated in sequence (series) rather than in parallel.     

Introduction of a de novo bioremediation ability, aryl reductive dechlorination, into anaerobic granular sludge by inoculation of sludge with Desulfomonile tiedjei.

Methanogenic upflow anaerobic granular-sludge blanket (UASB) reactors treat wastewaters at a high rate while simultaneously producing a useful product, methane; however, recalcitrant environmental pollutants may not be degraded. To impart 3-chlorobenzoate (3-CB)-dechlorinating ability to UASB reactors, we inoculated granular sludge in UASB reactors with either a pure culture of Desulfomonile tiedjei (a 3-CB-dechlorinating anaerobe) or a three-member consortium consisting of D. tiejei, a benzoate degrader, and an H2-utilizing methanogen. No degradation occurred in an uninoculated control reactor which was started with the same granular sludge, but inoculated reactors and granules from the inoculated UASB systems rapidly transformed 3-CB (54 mumol/day/g of granule biomass). After several months at a hydraulic retention time of 0.5 day, much shorter than the generation time of D. tiedjei, the reactors still dechlorinated 3-CB. This indicated that the bacteria were immobilized in the reactor granules, and by using an antibody probe for D. tiedjei, we demonstrated that this microorganism had colonized the sludge granules. These results represent the first addition of a pure culture or a defined microbial mixture to a viable waste treatment process to introduce a specific de novo degradative pathway into a granular-sludge consortium.     

Introduction of a de novo bioremediation ability, aryl reductive dechlorination, into anaerobic granular sludge by inoculation of sludge with Desulfomonile tiedjei.

Methanogenic upflow anaerobic granular-sludge blanket (UASB) reactors treat wastewaters at a high rate while simultaneously producing a useful product, methane; however, recalcitrant environmental pollutants may not be degraded. To impart 3-chlorobenzoate (3-CB)-dechlorinating ability to UASB reactors, we inoculated granular sludge in UASB reactors with either a pure culture of Desulfomonile tiedjei (a 3-CB-dechlorinating anaerobe) or a three-member consortium consisting of D. tiejei, a benzoate degrader, and an H2-utilizing methanogen. No degradation occurred in an uninoculated control reactor which was started with the same granular sludge, but inoculated reactors and granules from the inoculated UASB systems rapidly transformed 3-CB (54 mumol/day/g of granule biomass). After several months at a hydraulic retention time of 0.5 day, much shorter than the generation time of D. tiedjei, the reactors still dechlorinated 3-CB. This indicated that the bacteria were immobilized in the reactor granules, and by using an antibody probe for D. tiedjei, we demonstrated that this microorganism had colonized the sludge granules. These results represent the first addition of a pure culture or a defined microbial mixture to a viable waste treatment process to introduce a specific de novo degradative pathway into a granular-sludge consortium.     

Zinc deprivation of methanol fed anaerobic granular sludge bioreactors

The effect of omitting zinc from the influent of mesophilic (30 degrees C) methanol fed upflow anaerobic sludge bed (UASB) reactors, and latter zinc supplementation to the influent to counteract the deprivation, was investigated by coupling the UASB reactor performance to the microbial ecology of the bioreactor sludge. Limitation of the specific methanogenic activity (SMA) on methanol due to the absence of zinc from the influent developed after 137 days of operation. At that day, the SMA in medium with a complete trace metal solution except Zn was 3.4 g CH4-COD g VSS(-1) day(-1), compared to 4.2 g CH4-COD g VSS(-1) day(-1) in a medium with a complete (including zinc) trace metal solution. The methanol removal capacity during these 137 days was 99% and no volatile fatty acids accumulated. Two UASB reactors, inoculated with the zinc-deprived sludge, were operated to study restoration of the zinc limitation by zinc supplementation to the bioreactor influent. In a first reactor, no changes to the operational conditions were made. This resulted in methanol accumulation in the reactor effluent after 12 days of operation, which subsequently induced acetogenic activity 5 days after the methanol accumulation started. Methanogenesis could not be recovered by the continuous addition of 0.5 microM ZnCl2 to the reactor for 13 days. In the second reactor, 0.5 microM ZnCl2 was added from its start-up. Although the reactor stayed 10 days longer methanogenically than the reactor operated without zinc, methanol accumulation was observed in this reactor (up to 1.1 g COD-MeOH L(-1)) as well. This study shows that zinc limitation can induce failure of methanol fed UASB reactors due to acidification, which cannot be restored by resuming the continuous supply of the deprived metal.     

Distribution and change of microbial activity in combined UASB and AFB reactors for wastewater treatment

A thermophilic upflow anaerobic sludge blanket (UASB) reactor was combined with a mesophilic aerobic fluidized bed (AFB) reactor for treatment of a medium strength wastewater with 2,700?mg COD?l^?1. The COD removal efficiency reached 75% with a removal rate of 0.2 g COD?l^?1 h^?1 at an overall hydraulic retention time 14 hours. The distribution of microbial activity and its change with hydraulic retention time in the two reactors were investigated by measuring ATP concentration in the reactors and specific ATP content of the biomass. In the UASB reactor, the difference in specific ATP was significant between the sludge bed and blanket solution (0.02?mg ATP g VS^?1 versus 0.85?mg ATP g VS^?1) even though the ATP concentrations in these two zones were similar. A great pH gradient up to 4 was developed along the UASB reactor. Since a high ATP or biological activity in the blanket solution could only be maintained in a narrow pH range from 6.5 to 7.5, the sludge granules showed a high pH tolerance and buffering capacity up to pH 11. The suspended biomass in AFB reactor had a higher specific ATP than the biomass fixed in polyurethane carriers (1.6?mg ATP g VS^?1 versus 1.1?mg ATP g VS^?1), which implies a starvation status of the immobilized cells due to mass transfer limitation. The aerobes had to work under starvation conditions in this polishing reactor. The anaerobic biomass brought into AFB reactor contributed to an increase in suspended solids, but not the COD removal because of its fast deactivation under aerobic conditions. A second order kinetic model was proposed for ATP decline of the anaerobes. The results on distribution of microbial activity in the two reactors as well as its change with hydraulic retention time lead to further performance improvement of the combined anaerobic/aerobic reactor system.