Continuous electricity production from artificial wastewater using a mediator-less microbial fuel cell

A microbial fuel cell (MFC) was optimized in terms of MFC design factors and operational parameters for continuous electricity production using artificial wastewater (AW). The performance of MFC was analyzed through the polarization curve method under different conditions using a mediator-less MFC. The highest power density of 0.56 W/m2 was achieved with AW of 300 mg/l fed at the rate of 0.53 ml/min at 35 degrees C. The power per unit cell working volume was 102 mW/l, which was over 60 times higher than those reported in the previous mediator-less MFCs which did not use a cathode or an anode mediator. The power could be stably generated over 2 years.     

Enhancement of hexavalent chromium reduction and electricity production from a biocathode microbial fuel cell

Enhancement of Cr (VI) reduction rate and power production from biocathode microbial fuel cells (MFCs) was achieved using indigenous bacteria from Cr (VI)-contaminated site as inoculum and MFC architecture with a relatively large cathode-specific surface area of 340–900 m² m⁻³. A specific Cr (VI) reduction rate of 2.4 ± 0.2 mg g⁻¹VSS h⁻¹ and a power production of 2.4 ± 0.1 W m⁻³ at a current density of 6.9 A m⁻³ were simultaneously achieved at an initial Cr (VI) concentration of 39.2 mg L⁻¹. Initial Cr (VI) concentration and solution conductivity affected Cr (VI) reduction rate, power production and coulombic efficiency. These findings demonstrate the importance of inoculation and MFC architecture in the enhancement of Cr (VI) reduction rate and power production. This study is a beneficial attempt to improve the efficiency of biocathode MFCs and provide a good candidate of bioremediation process for Cr (VI)-contaminated sites.     

Treatment of biodiesel production wastes with simultaneous electricity generation using a single-chamber microbial fuel cell

Biodiesel production through transesterification of lipids generates large quantity of biodiesel waste (BW) containing mainly glycerin. BW can be treated in various ways including distillation to produce glycerin, use as substrate for fermentative propanediol production and discharge as wastes. This study examined microbial fuel cells (MFCs) to treat BW with simultaneous electricity generation. The maximum power density using BW was 487 ± 28 mW/m² cathode (1.5 A/m² cathode) with 50 mM phosphate buffer solution (PBS) as the electrolyte, which was comparable with 533 ± 14 mW/m² cathode obtained from MFCs fed with glycerin medium (COD 1400 mg/L). The power density increased from 778 ± 67 mW/m² cathode using carbon cloth to 1310 ± 15 mW/m² cathode using carbon brush as anode in 200 mM PBS electrolyte. The power density was further increased to 2110 ± 68 mW/m² cathode using the heat-treated carbon brush anode. Coulombic efficiencies (CEs) increased from 8.8 ± 0.6% with carbon cloth anode to 10.4 ± 0.9% and 18.7 ± 0.9% with carbon brush anode and heat-treated carbon brush anode, respectively.     

Effect of enrichment procedures on performance and microbial diversity of microbial fuel cell for Congo red decolorization and electricity generation

The purpose of this study was to determine the effect of enrichment procedure on the performance and microbial diversity of an air-cathode microbial fuel cell (MFC) which was explored for simultaneous azo dye decolorization and electricity generation. Two different enrichment procedures in which glucose and Congo red were added into the MFCs sequentially (EP1) or simultaneously (EP2) were tested by operating parallel MFCs independently for more than 6 months. The power density, electrode potential, Congo red decolorization, biofilm morphology, and bacterial diversity of the MFCs under the two enrichment procedures were compared and investigated. The results showed that the enrichment procedures have a negligible effect on the dye decolorization, but significantly affected the electricity generation. More than 90% decolorization at dye concentration of 300 mg/L was achieved within 170 h for the two tested enrichment procedures. However, the MFC with EP2 achieved a maximum power density of 192 mW/m², which was 75% higher than that of the MFC with EP1 (110 mW/m²). The depressed surfaces of the bacteria in the MFC with EP1 indicated the allergic response caused by the subsequent addition of Congo red. 16S rRNA sequencing analysis demonstrated a phylogenetic diversity in the communities of the anode biofilm and showed clear differences between the anode-attached populations in the MFCs with a different enrichment procedure. This study suggests that the enrichment procedure is important for the MFC explored for simultaneous dye decolorization and electricity generation.     

Renewable sustainable biocatalyzed electricity production in a photosynthetic algal microbial fuel cell (PAMFC)

Electricity production via solar energy capturing by living higher plants and microalgae in combination with microbial fuel cells are attractive because these systems promise to generate useful energy in a renewable, sustainable, and efficient manner. This study describes the proof of principle of a photosynthetic algal microbial fuel cell (PAMFC) based on naturally selected algae and electrochemically active microorganisms in an open system and without addition of instable or toxic mediators. The developed solar-powered PAMFC produced continuously over 100 days renewable biocatalyzed electricity. The sustainable performance of the PAMFC resulted in a maximum current density of 539 mA/m² projected anode surface area and a maximum power production of 110 mW/m² surface area photobioreactor. The energy recovery of the PAMFC can be increased by optimization of the photobioreactor, by reducing the competition from non-electrochemically active microorganisms, by increasing the electrode surface and establishment of a further-enriched biofilm. Since the objective is to produce net renewable energy with algae, future research should also focus on the development of low energy input PAMFCs. This is because current algae production systems have energy inputs similar to the energy present in the outcoming valuable products.     

Indole oxidation enhances electricity production in an E. coli-catalyzed microbial fuel cell

Microbial fuel cells (MFCs) generate electricity from the oxidation of dissolved organic matter. A variety of Gram-positive and Gram-negative bacteria, including Escherichia coli, produce a large quantity of indole, which functions as an extracellular signal molecule. This work explored the role of indole in a mediatorless E. coli catalyzed MFC. Although the presence of indole alone did not affect power generation, indole oxidation by the indole-oxidizing enzyme toluene-o-monooxygenase (TOM) enhanced power density by 9-fold. Open circuit voltage and polarization curve showed that indole oxidation by TOM produced a maximum power density of 5.4 mW/m² at 1,000 ohm. Cyclic voltammetric results suggested that indole oxidation resulted in the production of redox compounds. This study provides a novel means of enhancing power generation in E. coli-catalyzed MFCs.     

Biocathode microbial fuel cell for efficient electricity recovery from dairy manure

Microbial fuel cells (MFCs) represent a new biological method for generating electricity directly from biodegradable compounds. Efficiency of MFCs using manure as substrate is generally low. This study proposed a new design by incorporating biocathodes into a three-chamber MFC, which yielded maximum power densities much higher than those reported in literature. The new design placed cylindrical anode chamber for easy stirring and two symmetrical cathodic chambers with reduced anode-cathode distance. The biocathodes were applied to reduce charge transfer resistance. Additionally, biocathode microbial community was cultured to enrich favorable microorganisms. With external loading of 100 Ω, the power densities for new biocathode MFC using 2, 4, 6, 8 and 10% total solids diary manure reached 7.85±1.0 W m(-3), 7.84±1.20 W m(-3), 8.15±0.20 W m(-3), 7.60±0.97 W m(-3) and 5.63±0.97 W m(-3), respectively. The pH drop as a result of manure hydrolysis limited the power output. To provide detailed information of the microbial community in the biocathode MFC, the 454-pyrosequencing technique was adopted. The Firmicutes, γ-, β-, α- and δ-Proteobacteria, Bacteroidetes and Actinobacteria were the major groups on the anode, while γ-, β-, and α-Proteobacteria, Bacteroidetes and Actinobacteria were the predominant groups on the cathode.     

Effect of bacterial cell size on electricity generation in a single-compartmented microbial fuel cell

A single-compartmented microbial fuel cell composed of a graphite felt anode modified with Neutral Red (NR-anode) and a porous Fe(II)-carbon cathode (FeC-cathode) were compared for electricity generation from Microbacterium sp. and Pseudomonas sp. under identical conditions. Pseudomonas sp. was more than four times the size of Microbacterium sp. based on SEM images. In cyclic voltammetry, the redox reaction between Microbacterium sp and electrode was three times the rate observed between Pseudomonas sp. and the electrode based on the Y-axis (current) variation of cyclic voltammogram. The electric power generated by Microbacterium sp. was approx 3–4 times higher than that with Pseudomonas sp. during incubation for more than 150 days in the fuel cell.     

Construction and operation of freshwater sediment microbial fuel cell for electricity generation

In this work, sediment microbial fuel cell (SMFC) with granule activated carbon (GAC) cathode and stainless steel anode was constructed in laboratory tests and various factors on SMFC power output were investigated. The maximum power densities for the SMFC with GAC cathode was 3.5 mW m⁻², it was much higher than SMFC with round stainless steel cathode. Addition of cellulose reduced the output power from SMFC at the beginning of experiments, while the output power was found to increase after adding cellulose to sediments on day 90 of operation. On 160 day, maximum power density from the SMFC with adding 0.2% cellulose reached to 11.2 mW m⁻². In addition, the surface morphology of stainless steel anode on day 90 was analyzed by scanning electron microscope. It was found that the protection layer of the stainless steel as electrode in SMFCs was destroyed to some extent.     

Improved fuel cell and electrode designs for producing electricity from microbial degradation

A new one-compartment fuel cell was composed of a rubber bunged bottle with a center-inserted anode and a window-mounted cathode containing an internal, proton-permeable porcelain layer. This fuel cell design was less expensive and more practical than the conventional two-compartment system, which requires aeration and a ferricyanide solution in the cathode compartment. Three new electrodes containing bound electron mediators including a Mn(4+)-graphite anode, a neutral red (NR) covalently linked woven graphite anode, and an Fe(3+)-graphite cathode were developed that greatly enhanced electrical energy production (i.e., microbial electron transfer) over conventional graphite electrodes. The potentials of these electrodes measured by cyclic voltametry at pH 7.0 were (in volts): +0.493 (Fe(3+)-graphite); +0.15 (Mn(4+)-graphite); and -0.53 (NR-woven graphite). The maximal electrical productivities obtained with sewage sludge as the biocatalyst and using a Mn(4+)-graphite anode and a Fe(3+)-graphite cathode were 14 mA current, 0.45 V potential, 1,750 mA/m(2) current density, and 788 mW/m(2) of power density. With Escherichia coli as the biocatalyst and using a Mn(4+)-graphite anode and a Fe(3+)-graphite cathode, the maximal electrical productivities obtained were 2.6 mA current, 0.28 V potential, 325 mA/m(2) current density, and 91 mW/m(2) of power density. These results show that the amount of electrical energy produced by microbial fuel cells can be increased 1,000-fold by incorporating electron mediators into graphite electrodes. These results also imply that sewage sludge may contain unique electrophilic microbes that transfer electrons more readily than E. coli and that microbial fuel cells using the new Mn(4+)-graphite anode and Fe(3+)-graphite cathode may have commercial utility for producing low amounts of electrical power needed in remote locations.     

Enzymatic hydrolysis of cellulose coupled with electricity generation in a microbial fuel cell

Electricity can be directly generated by bacteria in microbial fuel cells (MFCs) from a variety of biodegradable substrates, including cellulose. Particulate materials have not been extensively examined for power generation in MFCs, but in general power densities are lower than those produced with soluble substrates under similar conditions likely as a result of slow hydrolysis rates of the particles. Cellulases are used to achieve rapid conversion of cellulose to sugar for ethanol production, but these enzymes have not been previously tested for their effectiveness in MFCs. It was not known if cellulases would remain active in an MFC in the presence of exoelectrogenic bacteria or if enzymes might hinder power production by adversely affecting the bacteria. Electricity generation from cellulose was therefore examined in two-chamber MFCs in the presence and absence of cellulases. The maximum power density with enzymes and cellulose was 100 +/- 7 mW/m(2) (0.6 +/- 0.04 W/m(3)), compared to only 12 +/- 0.6 mW/m(2) (0.06 +/- 0.003 W/m(3)) in the absence of the enzymes. This power density was comparable to that achieved in the same system using glucose (102 +/- 7 mW/m(2), 0.56 +/- 0.038 W/m(3)) suggesting that the enzyme successfully hydrolyzed cellulose and did not otherwise inhibit electricity production by the bacteria. The addition of the enzyme doubled the Coulombic efficiency (CE) to CE = 51% and increased COD removal to 73%, likely as a result of rapid hydrolysis of cellulose in the reactor and biodegradation of the enzyme. These results demonstrate that cellulases do not adversely affect exoelectrogenic bacteria that produce power in an MFC, and that the use of these enzymes can increase power densities and reactor performance.     

A direct fuel cell for the production of electricity from lignin

This report describes the use of an anthraquinone mediated fuel cell for the direct production of electrical energy from sulfonated lignin and Kraft Black Liquor. The cell produces the equivalent of 1 kWh for each 2-3 lb sulfonated lignin and 5-8 lb black liquor combustibles. In the case of the sulfonated lignin, chain session occurs during the oxidation process, reducing the molecular weight from ca. 2 x 10(4) to less than 1000 D.     

Impact of a static magnetic field on the electricity production of Shewanella-inoculated microbial fuel cells

The electricity production of Shewanella-inoculated microbial fuel cells (MFCs) under magnetic field (MF) exposure was investigated in different reactor systems. The persistency of the MF effect and the influences of MF intensity and direction on MFC performance were also studied. Application of a 100-mT static MF to the MFCs improved electricity production considerably, with an increase in the maximum voltage by 20-27% in both single- and two-chamber MFCs, while a more conspicuous improvement in the electricity generation was observed in a three-electrode cell. The MF effects were found to be immediate and reversible, and adverse effects seemed to occur when the MF was suddenly removed. The medium components analysis demonstrated that the application of MF led to an enhanced bioelectrochemical activity of Shewanella, and no significant promotion in mediator secretion was found. The improvement in the electricity production of MFCs under MF was mainly attributed to the enhanced bioelectrochemical activity, possibly through the oxidative stress mechanism. An accelerated cell growth under MF might also contribute to the enhanced substrate degradation and power generation.     

Electricity production from xylose using a mediator-less microbial fuel cell

Electricity generation integrated with xylose degradation was investigated in a two-chamber mediator-less microbial fuel cell (MFC). Voltage output followed saturation kinetics as a function of xylose concentration for concentration below 9.7 mM, with a predicted maximum of 86 mV (6.3 mW m(-2) or 116 mW m(-3)) and half-saturation constant (K(s)) of 0.29 mM. Xylose concentrations from 0.5 mM to 1.5 mM resulted in coulombic efficiencies and maximum voltage ranging from 41+/-1.6% to 36+/-1.2% and 55+/-2.0 mV to 70+/-3.0 mV respectively. Xylose degradation rate increased with increasing xylose concentration up to 9.7 mM and the predicted maximum degradation rate was 0.13 mM h(-1) and K(s) of 3.0 mM. Stirring by nitrogen in the anode chamber led to 99+/-2.3 mV maximum voltage (8.4+/-0.4 mW m(-2) or 153+/-7.1 mW m(-3)) and 5.9+/-0.3% coulombic efficiency at MFC running time 180 h, which were respectively 17+/-1.2% and 37+/-1.8%, higher than those without stirring. The COD removal under stirring was 22.1+/-0.3%, which was slightly lower than that of 23.7+/-0.4% under no stirring. However, stirring resulted in 59% lower xylose degradation rate. This work demonstrates that xylose can be used in the MFC for electricity production. Comparatively higher electricity generation and coulombic efficiency can be obtained by adjusting initial xylose concentration and applying stirring in the anode chamber.     

Bioelectricity production using a new electrode in a microbial fuel cell

Electrode materials play a key role in enhancing the electricity generation in the microbial fuel cell (MFC). In this study, a new material (Ti-TiO(2)) was used as an anode electrode and compared with a graphite electrode for electricity generation. Current densities were 476.6 and 31 mA/m(2) for Ti-TiO(2) and graphite electrodes, respectively. The PCR-DGGE analysis of enriched microbial communities from estuary revealed that MFC reactors were dominated by Shewanella haliotis, Enterococcus sp., and Enterobacter sp. Bioelectrochemical kinetic works in the MFC with Ti-TiO(2) electrode revealed that the parameters by non-linear curve fitting with the confidence bounds of 95% gave good fit with the kinetic constants of η (difference between the anode potential and anode potential giving one-half of the maximum current density) = 0.35 V, K (s) (Half-saturation constant) = 2.93 mM and J (max) = 0.39 A/m(2) for T = 298 K and F = 96.485 C/mol-e(-). From the results observed, it is clear that Ti-TiO(2) electrode is a promising candidate for electricity generation in MFC.     

Simultaneous wastewater treatment,electricity generation and biomass production by an immobilized photosynthetic algal microbial fuel cell

A photosynthetic algal microbial fuel cell (PAMFC) was constructed by the introduction of immobilized microalgae (Chlorella vulgaris) into the cathode chamber of microbial fuel cells to fulfill electricity generation, biomass production and wastewater treatment. The immobilization conditions, including the concentration of immobilized matrix, initial inoculation concentration and cross-linking time, were investigated both for the growth of C. vulgaris and power generation. It performed the best at 5 % sodium alginate and 2 % calcium chloride as immobilization matrix, initial inoculation concentration of 10⁶ cell/mL and cross-linking time of 4 h. Our findings indicated that C. vulgaris immobilization was an effective and promising approach to improve the performance of PAMFC, and after optimization the power density and Coulombic efficiency improved by 258 and 88.4 %, respectively. Important parameters such as temperature and light intensity were optimized on the performance. PAMFC could achieve a COD removal efficiency of 92.1 %, and simultaneously the maximum power density reached 2,572.8 mW/m³ and the Coulombic efficiency was 14.1 %, under the light intensity of 5,000 lux and temperature at 25 °C.     

Experimental evaluation of influential factors for electricity harvesting from sediment using microbial fuel cell

The aim of this study was to evaluate limiting factors affecting electricity output from sediment microbial fuel cells (sediment MFCs). In laboratory tests, various factors likely to be encountered in field application were divided into controllable and uncontrollable ones. Based on the findings, it could be suggested that the sediment MFCs can be operated with an anode to cathode area ratio of at least 5:1 and at high external loads (1000 Ω) when the cathode is closely placed to the anode, though DO concentration at the cathode must be kept above 3 mg/l. Furthermore, no significant effect on current production over a prolonged period was observed within the sediment temperature range of 20–35 °C, but was negatively affected by lower temperatures (10 °C). These observations provide important factors with respect to the construction and operation of sediment MFCs at field sites, which will aid in maximizing electricity output.     

Performance of membrane-less microbial fuel cell treating wastewater and effect of electrode distance and area on electricity production

Performance of mediator-less and membrane-less microbial fuel cell (ML-MFC) was evaluated to treat synthetic wastewater and actual sewage. The ML-MFC gave COD and BOD removal efficiencies of 88% and 87%, respectively, and TKN removal was around 45-50%. Biomass granulation was observed in the anode compartment of ML-MFC. Effect of distance between the electrodes and total surface area of anode on electricity production was evaluated under variable external resistance. Maximum power density of 10.9 and 10.13 mW/m2 was observed at lower spacing between the electrodes (20 cm) and for lesser surface area of the anode, respectively. With variation in the carbon source in the feed, variation in power production was observed.     

A microbial fuel cell capable of converting glucose to electricity at high rate and efficiency

A microbial fuel cell containing a mixed bacterial culture utilizing glucose as carbon source was enriched to investigate power output in relation to glucose dosage. Electron recovery in terms of electricity up to 89% occurred for glucose feeding rates in the range 0.5–3 g l^–1 d^–1, at powers up to 3.6 W m^–2 of electrode surface, a five fold higher power output than reported thus far. This research indicates that microbial electricity generation offers perspectives for optimization.