心肌肌钙蛋白Ⅰ的分子印迹电化学生物传感器

应用分子印迹技术,以邻苯二胺和对苯二酚为功能单体,心肌肌钙蛋白Ⅰ(cTnI)为模板分子,在pH 7.0磷酸盐缓冲液中,利用循环伏安法在玻碳电极表面聚合形成了分子印迹膜.该分子膜对cTnI有特异性识别作用,在0.01～2.00 μg/mL的范围内,cTnI的浓度与氧化峰电流的变化呈线性关系,检测下限为2 ng/mL,响应时间为15 min.该分子印迹传感器具有制备简单、特异性及稳定性好等优点.     

量子点表面分子印迹光纤传感器的制备及应用

近年来,许多研究人员不断努力为药物、除草剂、食品添加剂等小分子物质高特异性、高灵敏的检测和分析开发新的方法和技术。然而,目前通用的分子检测方法的实施需要较长的前处理时间、昂贵的大型仪器设备及专业操作人员,无法实现有选择的识别及快速的现场检测。所以,在本研究中我们将量子点表面分子印迹聚合物(QDs@MIPs)与光纤相结合,构建了一种新的光纤探头,并将该光纤探头应用于光纤传感器,检测小分子物质莱克多巴胺(RAC)。试验中,我们对QDs@MIPs的表征、光纤探头的性能、光纤探头对RAC的浓度响应、光纤传感器的特异性及光强分布进行了探究。研究结果表明,该光纤探头应用于光纤传感器能够提高光纤传感器的灵敏度,使分子印迹光纤传感器具有更高的特异性识别能力和较强的抗干扰能力,同时检测过程简便快捷,适用于快速的现场检测。     

新型青霉素生物传感器的研究

以青霉素为模板分子,采用溶胶-凝胶法合成分子印迹膜,以浸泡的方法移除印迹分子,制备青霉素分子印迹膜电极。本印迹电极能有效地避免类似物对其测定的干扰。通过循环伏安法研究传感器对青霉素的响应特性,结果表明:富集时间为200 s,在0.1~1.8μg/L质量浓度范围内,青霉素在磷酸缓冲液(PBS)中的电流强度与其浓度呈良好的线性关系。吸附后的膜电极用甲醇洗脱后再生,可以重复利用3次,可以应用到实际检测中。     

地高辛标记Ucp2基因RNA探针的制备和应用

目的:制备用于检测小鼠胚胎早期Ucp2基因表达的地高辛标记的特异性RNA探针。方法:提取小鼠胚胎脑组织总RNA,设计引物,通过RT-PCR方法获取Ucp2基因片段,将其克隆到pGEM-T载体。分别利用Sp6、T7和Ucp2特异性引物,PCR扩增获得转录模板,通过Sp6及T7 RNA聚合酶,获得地高辛标记的正义、反义Ucp2 RNA原位杂交探针。检测标记探针的效价后,通过全胚胎原位杂交分析制备探针的特异性和杂交效果。结果:成功获得Ucp2基因正义、反义探针,反义探针能高效灵敏检测到Ucp2基因在小鼠胚胎Ed9.5、Ed10.5神经系统呈现高表达,而正义探针未能检测到表达信号。结论:成功制备了特异高效的地高辛标记Ucp2 RNA原位杂交探针,为进一步研究Ucp2基因在小鼠胚胎组织中的表达,尤其在神经组织的定位奠定基础。     

核壳型离子印迹聚合物的制备与应用

离子印迹聚合物(IIPs)是利用分子印迹技术对目标离子进行印迹、聚合进而得到对模板离子有选择性吸附的聚合物。核壳型离子印迹聚合物作为一种新型吸附材料被应用于样品的处理和实际检测中。本文对核壳型离子印迹聚合物的核壳类型、印迹聚合物的制备方法及实际检测应用等最新研究进展进行综述,为核壳型离子印迹聚合物的研究与应用提供参考。     

沉淀聚合法制备1-脱氧野尻霉素分子印迹聚合物微球及其性能研究

本研究制备了1-脱氧野尻霉素分子印迹聚合物微球,考察溶剂、反应时间对分子印迹聚合物产率以及性能的影响。以1-脱氧野尻霉素为模板分子,α-甲基丙烯酸(MAA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,采用沉淀聚合法合成分子印迹微球,采用静态吸附及扫描电镜(SEM)的方法对微球进行表征。结果表明,当反应时间为24 h、乙腈为溶剂时,所制得印迹聚合物微球的形貌和吸附性能较好,对1-脱氧野尻霉素与N-甲基-1-脱氧野尻霉素的选择性分离因子α为2.26,说明分子印迹聚合物微球对1-脱氧野尻霉素分子有特异性吸附和识别能力。     

浅谈菌丝体表面分子印迹吸附剂的选择性吸附

通过制备的方法获得菌丝体表面分子印迹吸附剂,本文系统的分析和探讨了针对模板金属离子菌丝体表面分子印迹吸附剂的吸附选择性。通过实验研究证明,菌丝体表面分子印迹吸附剂如果是以Ni2+为模板制备的,相对于非印迹吸附剂来讲,其对Cr3+、Cu2+、Ni2+的吸附容量以及吸附速率的提高幅度都是非常大的。而菌丝体表面分子印迹吸附剂相对于具有Ni2+金属离子混合溶液来讲,其对Ni2+的选择性以及吸附容量要比含有诸如Cu2+以及Cr3+的金属离子提高的都要明显很多;印迹吸附剂相对于非印迹吸附剂来讲,其在吸附非模板金属离子Cu2+以及Cr3+时具有明显降低的选择性。     

恩诺沙星分子印迹电化学传感器的制备及其在食品快速检测中的应用

以恩诺沙星(ENRO)为模板分子,邻苯二胺(OPD)和邻氨基苯酚(OAP)为复合功能单体,在NaAc-HAc缓冲液中,采用电聚合法在玻碳电极表面制备了能够特异识别模板分子及其结构类似物的分子印迹电化学传感器。试验选用含1mol/L氯化钾及1mmol/L铁氰化钾的混合液作为表征溶液,采用循环伏安法和方波伏安法研究了传感器的电化学响应特性,并优化制备和检测条件。结果表明,在最佳条件下,恩诺沙星在2×10~(-6)mol/L～4×10~(-5)mol/L浓度范围内线性关系良好,检出限为7. 0×10~(-7)mol/L,该传感器具有良好的稳定性和重现性,对恩诺沙星以及结构类似物具有良好的选择性。采用该传感器对实际样品牛奶、鸡肉、猪肉和鸡蛋中的恩诺沙星进行检测,加标回收率在83. 2%～92. 7%之间,相对标准偏差(RSD)在1. 0%～4. 8%之间(n=5),该传感器选择性强、稳定性好、操作简便、检测快速灵敏、成本低、具有良好的应用前景。     

白藜芦醇分子印迹聚合物微球的制备及特性评价(英文)

以聚苯乙烯微球为种球,白藜芦醇为模板分子,采用单步溶胀聚合法在N,N-二甲基甲酰胺体系中制备了单分散分子印迹聚合物微球。用扫描电镜对微球的结构和形貌进行了表征,并研究了微球的制备条件和吸附特性。微球的凹陷可有效地增加微球的比表面积和结合位点,从而提高了模板分子的结合速率及微球的印迹容量。     

基于分子印迹技术的细菌传感检测

分子印迹因其材料结构的稳定性及靶标物识别的特异性而被广泛应用于生化分离分析的相关领域。近年来，将具有选择性捕获、分离和富集靶标物等优势的分子印迹技术与生化传感检测技术有机结合，是目前细菌等微生物高效检测领域备受关注的研究热点。本文就分子印迹技术在细菌分析中的印迹方法、分析检测技术和典型应用等方面的最新进展进行综述。首先介绍了细菌分子印迹原理，对表面印迹的材料以及直接压印、间接印迹和电聚合等制备方法进行了总结和归纳；重点对基于荧光、电化学、石英晶体微天平（QCM）等检测模式的细菌印迹传感监测在细菌分析检测及其与微流控芯片技术耦合的应用和进展进行了综述；最后，提出了存在的挑战及发展的趋势。     

Cyclic voltammetry characterization of metal complex imprinted polymer

Polymer capable of specific binding to Cu(2+)-2, 2'-dipyridyl complex was prepared by molecular imprinting technology. The binding specificity of the polymer to the template (Cu(2+)-2, 2'-dipyridyl complex) was investigated by cyclic voltammetric scanning using the carbon paste electrode modified by polymer particles in phosphate buffer solution. Factors that influence rebinding of the imprinted polymer were explored. The results demonstrated that cyclic voltammetry was an efficient approach to explore interactions between template and imprinted polymers.     

Synthesis of molecularly imprinted polymers using a functionalized initiator for chiral-selective recognition of propranolol

We present a new concept of synthesis for preparation of molecularly imprinted polymers using a functionalized initiator to replace the traditional functional monomer. Using propranolol as a model template, a carboxyl-functionalized radical initiator was demonstrated to lead to high-selectivity polymer particles prepared in a standard precipitation polymerization system. When a single enantiomer of propranolol was used as template, the imprinted polymer particles exhibited clear chiral selectivity in an equilibrium binding experiment. Unlike the previous molecular imprinting systems where the active free radicals can be distant from the template-functional monomer complex, the method reported in this work makes sure that the actual radical polymerization takes place in the vicinity of the template-associated functional groups. The success of using functional initiator to synthesize molecularly imprinted polymers brings in new possibilities to improve the functional performance of molecularly imprinted synthetic receptors.     

Determination of digoxin in serum samples using a flow-through fluorosensor based on a molecularly imprinted polymer

This work describes the development of a competitive flow-through FIA assay for digoxin using a molecularly imprinted polymer (MIP) as the recognition phase. In previous work, a number of non-covalent imprinted polymers were synthesised by “bulk” polymerisation. The digoxin binding and elution characteristics of these MIPs were then evaluated to obtain a highly selective material for integration into a sensor. The optimum MIP was synthesised by photo-initiated polymerisation of a mixture containing digoxin, MAA, EDGMA and AIBN in acetonitrile. The bulk polymer was ground and sieved and the template removed by Soxhlet extraction in MeOH/ACN. The MIP was packed into a flow cell and placed in a spectrofluorimeter to integrate the reaction and detection systems. The physical and chemical variables involved in digoxin determination by the sensor (nature and concentration of solution, flow rates, etc.) were optimised. Binding with the non-imprinted polymer (NIP) was also analysed. The new fluorosensor showed high selectivity and sensitivity, a detection limit of 1.7 × 10⁻² μg l⁻¹, and high reproducibility (R.S.D. of 1.03% and 1.77% for concentrations of 1.0 × 10⁻³ and 4.0 × 10⁻³ mg l⁻¹, respectively). Selectivity was tested by determining the cross-reactivity of several compounds with structures analogous to digoxin. Under the assay conditions used, in which the potential interfering compounds were in concentrations 100 times higher than that of the analyte, no interference was recorded. The proposed fluorosensor was successfully used to determine digoxin concentration of human serum samples.     

Synthetic cinchonidine receptors obtained by cross-linking linear poly(methacrylic acid) derivatives as an alternative molecular imprinting technique

A molecular imprinting approach to construct synthetic receptors was examined, wherein a linear pre-polymer bearing functional groups for intermolecular interaction with a given molecule is cross-linked in the presence of the molecule as a template, and subsequent removal of the template from the resultant network-polymer is expected to leave a complementary binding site. Poly(methacrylic acid) (PMAA) derivatized with a vinylbenzyl group as a cross-linkable side chain was utilized as the pre-polymer for the molecular imprinting of a model template, (-)-cinchonidine. Selectivity of the imprinted polymer was evaluated by comparing the retentions of the original template, (-)-cinchonidine and its antipode (+)-cinchonine in chromatographic tests, exhibiting a selectivity factor up to 2.4. By assessment of the imprinted polymers in a batch mode, a dissociation constant at 20 degrees C for (-)-cinchonidine was estimated to be K (d) = 2.35 x 10(-6) M (the number of binding sites: 4.54 x 10(-6) mol/g-dry polymer). The displayed affinity and selectivity appeared comparable to those of an imprinted polymer prepared by a conventional monomer-based protocol, thus showing that the pre-polymer, which can be densely cross-linked, is an alternative imprinter for developing template-selective materials. (-)-Cinchonidine-imprinted polymers were prepared and assessed using the pre-polymers bearing different densities of the vinylbenzyl group and different amounts of the cross-linking agent to examine the appropriate density of the cross-linking side chain that was crucial for developing the high affinity and selectivity of the imprinted polymers.     

Quartz crystal microbalance for the determination of daminozide using molecularly imprinted polymers as recognition element

As the daminozide (DM) and its metabolite have been identified to be potentially carcinogenic, rapid detection method for them is necessary for food safety. A type of piezoelectric crystal sensor has been prepared by using a molecularly imprinted polymer (MIP) as recognition element. The molecularly imprinted polymer was prepared by hot-induced precipitation polymerization, and then the polymer particles were fixed on the surface of the electrode. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to evaluate the obtained imprinted polymer particles and the MIP sensitive film coated on the electrode. The results showed that a typical time-response curve of the MIP-coated crystal to the DM solution had been given, frequency shifts versus logarithm changes of DM showed good linear correlation within the concentration range of 1.0x10(-9) to 10(-6) mg/mL (y=11.38 lg x+115.45, r=0.9872) and 1.0x10(-6) to 10(-1) mg/mL (y=25.22lgx+209.44, r=0.9938), respectively. The detection limit was 5.0x10(-8) mg/mL (S/N=3), which is lower than that of conventional methods. Further, computer simulation technology was employed to investigate the interaction between methacrylic acid and DM for elucidating the recognition mechanism. The influencing factor pH has also been investigated. The injection experiments of DM structurally related compounds indicated that the obtained sensor has high sensitivity, excellent selectivity, low cost, good reproducibility, and reusable property by combining with piezoelectric crystal and molecularly imprinted polymer.     

Synthesis and evaluation of a selective molecularly imprinted polymer for the contraceptive drug levonorgestrel

A molecularly imprinted polymer (MIP) has been prepared using levonorgestrel (LEV) as template. The polymer was synthesised in a non-covalent approach using methacrylic acid (MAA) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linking monomer via a free radical polymerization. An equivalent blank polymer was also synthesised in the absence of the template compound. Batch adsorption experiments were used to evaluate the binding affinity of the imprinted polymer. After packing MIP into a stainless steel column (150 mm x 4.6 mm i.d.), retention and elution of the template and related compounds were evaluated by high-performance liquid chromatography (HPLC). This LEV imprinted polymer was further applied for selective solid phase extraction (SPE) of LEV from human serum. It was confirmed that the binding ability of the prepared MIP for LEV was essentially sufficient in the presence of other compounds coexisting in serum sample. Therefore, as a selective and efficient solid phase material, LEV imprinted polymer has a high potential application in analysis of this steroidal hormone in clinical purposes.     

Glucose sensors based on electrodeposition of molecularly imprinted polymeric micelles: a novel strategy for MIP sensors

A voltammetric glucose sensor was prepared from novel molecularly imprinted polymeric micelles (MIPMs) through direct electrodeposition. The MIPMs, which were photo-crosslinkable and nano-scaled with high specific surface area, were prepared via macromolecule self-assembly of an amphiphilic photo-crosslinkable copolymer, combined with a molecular imprinting technique using glucose as the template molecule. A MIP film was formed in situ on the electrode surface by electrodeposition of the MIPMs, while photo-crosslinking led to a robust film which showed good solvent resistant to dissolution. With these features, the resulting sensor showed good response and selectivity towards glucose. In particular, the linear response of this glucose sensor ranged from 0.2 mM to 8 mM and its comparatively higher detection limit, about 10 mM, indicated numerous effective recognition sites among the polymer matrix due to the large specific surface area of MIPM. In addition, this MIP sensor also showed good stability and reversibility. The contribution of this work lies in not only the invention of a new type of glucose MIP sensor with good performance, but also the creation of a novel strategy to develop advanced MIP sensors for a wide range of templates in viewing of the versatility of the amphiphilic copolymers and the ease of control and applicability of the electrodeposition process.     

Voltammetric sensor for vanillylmandelic acid based on molecularly imprinted polymer-modified electrodes

Despite the increasing number of applications of molecularly imprinted polymers (MIPs) in analytical chemistry, the construction of a biomimetic voltammetric sensor remains still challenging. This work investigates the development of a voltammetric sensor for vanillylmandelic acid (VMA) based on acrylic MIP-modified electrodes. Thin layers of MIPs for VMA have been prepared by spin coating the surface of a glassy carbon electrode with the monomers mixture (template, methacrylic acid, a cross-linking agent and solvent), followed by in situ photopolymerisation. After extraction of the template molecule, the peak current recorded with the imprinted sensor after rebinding was linear with VMA concentration in the range 19-350 microg ml(-1), whereas the response of the control electrode is independent of incubation concentration, and was about one-tenth of the value recorded with the imprinted sensor at the maximum concentration tested. Under the conditions used, the sensor is able to differentiate between VMA and other closely structural-related compounds, such as 3-methoxy-4-hydroxyphenylethylene glycol (not detected), or 3,4- and 2,5-dihydroxyphenilacetic acids, which are adsorbed on the bare electrode surface but not at the polymer layer. Homovanillic acid was detected with the imprinted sensors after incubation, indicating that the presence of both methoxy and carboxylic groups in the same position as in VMA is necessary for effective binding in the imprinted sites. Nevertheless, both species can be differentiated by the oxidation potential. It can be concluded that MIP-based voltammetric electrodes are very promising analytical tool for the development of highly selective analytical sensors.     

An innovative approach to molecularly imprinted capillaries for polar templates by grafting polymerization

Molecularly imprinted polymers have been successfully used as selective stationary phases in capillary electrophoresis. Notwithstanding, this technique suffers from several drawbacks as the loss of molecular recognition properties in aqueous media and the lack of feasibility for imprinted systems directed towards highly polar templates soluble in aqueous environments only. Thus, the preparation of imprinted polymers for highly polar, water-soluble analytes, represents a challenge. In this work, we present an innovative approach to overcome these drawbacks. It is based on a surface molecular imprinting technique that uses preformed macromonomers as both functional recognition elements and cross-linking agents. A poly-2-hydroxyethyl-co-methacrylic acid linear polymer was grafted from the surface of silica capillaries. The grafted polymer was exhaustively esterified with methacrylic anhydride to obtain polyethylendimethacrylate-co-methacrylic acid linear chains. Then, as a proof of concept, an adequate amount of a very polar template like penicillin V was added in a hydro-organic mixture, and a thin layer of imprinted polymer was obtained by cross-linking the polymer linear chains. The binding behaviour of the imprinted and non-imprinted capillaries was evaluated in different separation conditions in order to assess the presence of template selectivity and molecular recognition effects. The experimental results clearly show that this innovative kind of imprinted material can be easily obtained in very polar polymerization environments and that it is characterized by enhanced molecular recognition properties in aqueous buffers and good selectivity towards the template and strictly related molecules.