A novel approach to evaluate the permeability of cake layer during cross-flow filtration in the flocculants added membrane bioreactors

In order to obtain a better understanding of the cake layer formation mechanism in the flocculants added MBRs, a model was developed on the basis of particle packing model considering cake collapse effect and a frictional force balance equation to predict the porosity and permeability of the cake layers. The important characteristic parameters of the flocs (e.g., floc size, fractal dimensions) and operating parameters of MBRs (e.g., transmembrane pressure, cross-flow velocity) are considered in this model. With this new model, the calculated results of porosities and specific cake resistances under different MBR operational conditions agree fairly well with the experimental data.     

Performance of an anaerobic membrane bioreactor in which granular sludge and dynamic filtration are integrated

To alleviate the fouling of a filter, simple substrates, dynamic filtration, and granular sludge were applied in an anaerobic membrane bioreactor (AnMBR). The results showed that under a transmembrane pressure < 20 kPa, the filter flux ranged between 15 and 20 l (m^?2 h)^?1 for a period of 30 days. The flux was higher than the typical flux of AnMBRs with conventional membranes and most current dynamic filters. In addition, the low cost of the filter avoided the need for a higher flux. Moreover, a stable granular sludge bed, which consumed all volatile fatty acids, was maintained. A compact fouling/filtration layer formed on the filter, which contributed to low effluent chemical oxygen demand concentrations and turbidity. In addition, substrate scarcity in the filtration zone resulted in the evolution of diverse bacteria on the filter.     

Removal of microbial indicators from municipal wastewater by a membrane bioreactor (MBR)

The impact of removable and irremovable fouling on the retention of viral and bacterial indicators by the submerged microfiltration membrane in an MBR pilot plant was evaluated. Escherichia coli, sulphite-reducing Clostridium spores, somatic coliphages and F-specific RNA bacteriophages were used as indicators. The membrane demonstrated almost complete removal of E. coli and sulphite-reducing Clostridium spores. However, there was no correlation with membrane fouling. The phage removal varied in accordance with the irremovable fouling, rising from 2.6 to 5.6 log₁₀ units as the irremovable fouling increased (measured by the change in the transmembrane pressure). In contrast, removable fouling did not have any effect on the retention of viruses by the membrane. These results indicate that irremovable membrane fouling may affect the removal efficiency of MBRs and, therefore, their capacity to ensure the required microbiological standards for the permeate achieved.     

Microbial community and biomass characteristics associated severe membrane fouling during start-up of a hybrid anoxic-oxic membrane bioreactor

In MBR, severe membrane fouling is often observed in the initial phase in which biomass is yet fully acclimated and stabilized in terms of microbial community structure and biomass characteristics. The focus of this study was to investigate the microbial community development and its influence on biomass characteristics and membrane fouling during start-up of a hybrid anoxic-oxic MBR. PCR-DGGE analysis indicated that the microbial community shifted in start-up period when a severe membrane fouling was observed. Small particle size, high fractal dimension (DF) and high EPS production, which were closely associated with microbial community, were found to be the major contributors to the severe fouling. Microbial community development was most likely the ultimate factor responsible for the severe membrane fouling.     

Prediction of membrane fouling in MBR systems using empirically estimated specific cake resistance

The focus of this study was to empirically estimate the specific cake resistance (SCR) by the variation in shear intensity (G) in four laboratory-scale MBRs. The control reactor (MBR₀) was operated with aeration only while other MBRs (MBR₁₅₀, MBR₃₀₀ and MBR₄₅₀) were operated with aeration and mechanical mixing intensities of 150, 300 and 450 rpm, respectively. It was found that the SCR was strongly correlated (R² = 0.99) with the fouling rates in the MBRs. Moreover, the contribution of cake resistance (R_c) to the total hydraulic resistance (R_t) was predominant compared to the irreversible fouling resistance (R_f). On this basis, the cake filtration model was selected as a predictive tool for membrane fouling. This model was modified by replacing the SCR with its empirical shear intensity relationship. The modified model can predict the fouling rate for a given shear intensity (G) within 80 and 250 s⁻¹ in a MBR system.     

Characterizing membrane foulants in MBR with addition of polyferric chloride to enhance phosphorus removal

The effect of polymeric ferric chloride (PFC) addition on phosphorus removal and membrane fouling were investigated in an anoxic/oxic submerged membrane bioreactor. The total phosphorus concentration in effluent averaged at 0.26 mg/L with PFC addition of 10-15 mg/L, while the rate of membrane fouling increased 1.6 times over the control MBR (without PFC addition). Three-dimensional excitation-emission matrix fluorescence spectroscopy and Gel Filtration Chromatography analysis indicated that soluble microbial byproduct-like materials and large molecules (M(W)>100 kDa) were one of the main contributors of biofouling. Fourier transform infrared spectrum confirmed that the major components of the cake layer were proteins and polysaccharides materials. Scanning electron microscopy demonstrated that membrane surfaces were covered with compact gel layer formed by organic substances and Energy Dispersive X-ray analysis indicated that ferric metals were the most important inorganic pollutants. Consequently, soluble organic substances and dose of PFC should be controlled to minimize membrane fouling.     

Factors affecting the performance of membrane bioreactor for piggery wastewater treatment

This study was conducted to identify the factors affecting the performance of membrane bioreactor (MBR) for piggery wastewater treatment. The change of organic and nitrogen concentrations in piggery wastewater was studied to investigate the treatment efficiency. The increase of COD, BOD and NH₃–N from 1150 to 2050 mg/L, 683 to 1198 mg/L and 154 to 248 mg/L has led to the decrease of treatment efficiency. Removal efficiencies of COD, BOD and NH₃–N have decreased from 96.0% to 92.0%, 97.0% to 92.7% and 93.2% to 69.5%, respectively. The effects of biomass characteristics on membrane fouling were determined based on Pearson’s correlation coefficient (r_p). It was found that MLSS had a negative correlation with permeate flux (r_p = −0.745, at significant level of 0.05) while sludge floc size a positive correlation (r_p = 0.731, at significant level of 0.05). MLSS and sludge floc size were found to be the dominant factors that controlled the membrane filterability while sludge viscosity, EPS, SMP and SV₃₀ have taken as the sub-factors affecting membrane fouling.     

Effects of low-concentration Cr(VI) on the performance and the membrane fouling of a submerged membrane bioreactor in the treatment of municipal wastewater

The effects of low-concentration Cr(VI) (0.4 mg?l^?1) on the performance of a submerged membrane bioreactor (SMBR) in the treatment of municipal wastewater, as well as membrane fouling were investigated. Compared with the SMBR for control municipal wastewater, the SMBR for Cr(VI)-containing municipal wastewater had a higher concentration of soluble microbial products (SMP) with lower molecular weights, and smaller sludge particle sizes. Furthermore, low-concentration Cr(VI) induced membrane fouling, especially irreversible membrane pore blocking, which markedly shortened the service life of the membrane.     

Hydrogenotrophic denitrification of synthetic aquaculture wastewater using membrane bioreactor

A hydrogenotrophic denitrification system was evaluated in removing nitrate from synthetic aquaculture wastewater for recirculation purposes. Two membrane bioreactor (MBR) systems, namely, aeration–denitrification system (ADS) and denitrification–aeration system (DAS) were studied with 50 mg/L of influent concentrations for both organic matter and nitrate nitrogen. The DAS achieved better removal efficiency of 91.4% total nitrogen (T-N) and denitrification rate of 363.7 mg/L.day at a HRT of 3 h compared to ADS. Further, there was no nitrite accumulation in the DAS effluent. The nitrite accumulation in ADS effluent was lesser when CO₂ was used as buffer rather than K₂HPO₄ and KH₂PO₄. Estimation of kinetic parameters of hydrogenotrophic bacteria indicated lesser sludge production compared to heterotrophic denitrification. In the DAS, membrane fouling was nonexistent in the aeration reactor that was used to produce the recirculating effluent. On the contrary, membrane fouling was observed in the denitrification reactor that supplied hydrogen to the mixed liquor. Thus, this study demonstrated DAS capability in maintaining the acceptable water quality appropriate for aquaculture, in which a closed recirculating system is typically used.     

Comparison between a moving bed membrane bioreactor and a conventional membrane bioreactor on membrane fouling

A membrane bioreactor filled with carriers instead of activated sludge named a moving bed membrane bioreactor (MBMBR) was investigated to minimize the effect of suspended solids on membrane fouling. The MBMBR and a conventional membrane bioreactor (CMBR) were operated in parallel for about two months. Unexpectedly, the rate of membrane fouling in MBMBR was about three times of that in CMBR. MBMBR showed a higher cake layer resistance than CMBR due to plenty of filamentous bacteria inhabited in suspended solids in MBMBR. Protein and polysaccharide contents of soluble EPS in MBMBR were obviously larger than those in CMBR. It could be speculated that the overgrowth of filamentous bacteria in MBMBR resulted in severe cake layer and induced a large quantity of EPS, which deteriorated the membrane fouling.     

A hybrid anaerobic membrane bioreactor coupled with online ultrasonic equipment for digestion of waste activated sludge

Anaerobic membrane bioreactor and online ultrasonic equipment used to enhance membrane filtration were coupled to form a hybrid system (US-AnMBR) designed for long-term digestion of waste activated sludge. The US-AnMBR was operated under volatile solids loading rates of 1.1-3.7 gVS/L·d. After comprehensive studies on digestion performance and membrane fouling control in the US-AnMBR, the final loading rate was determined to be 2.7 gVS/L·d with 51.3% volatile solids destruction. In the US-AnMBR, the improved digestion was due to enhanced sludge disintegration, as indicated by soluble matter comparison in the supernatant and particle size distribution in the digested sludge. Maximum specific methanogenic activity revealed that ultrasound application had no negative effect on anaerobic microorganisms. Furthermore, implementing ultrasound effectively controlled membrane fouling and successfully facilitated membrane bioreactor operation. This lab-scale study demonstrates the potential feasibility and effectiveness of setting up a US-AnMBR system for sludge digestion.     

Performance of a submerged membrane bioreactor for the aerobic treatment of abattoir wastewater

The performance of a submerged membrane bioreactor (SMBR) has been investigated for abattoir wastewater (AW) treatment. The chemical oxygen demand (COD) of permeate has not exceeded 25 mg L⁻¹ providing an average COD removal of 98%. Microbiological analysis showed that the SMBR has allowed a complete removal of fecal coliforms, Listeria and Salmonella. A significant reduction in the excess biomass production was also observed. In fact, the yield of biomass production (Yobs) ranged between 0 and 0.106 g suspended solids/g COD removed.The study of the dynamic of bacterial communities using the single strand conformation polymorphism (SSCP) method showed a significant change in the population structure and revealed a correlation between the sludge production yield and the bacterial communities.     

Effect of hydraulic retention time on membrane fouling and biomass characteristics in submerged membrane bioreactors

In this paper, three identical membrane bioreactors (MBRs) were operated in parallel in order to specify the influence mechanism of hydraulic retention time (HRT) on MBR. The results showed that the removal efficiency of chemical oxygen demand (COD) was stable though it decreased slightly as HRT decreased, but biomass activity and dissolved oxygen (DO) concentration in sludge suspension decreased as HRT decreased. The filamentous bacteria grew easily with decreasing HRT. The extracellular polymeric substances (EPS) concentration and sludge viscosity increased significantly as filamentous bacteria excessively grew. The over growth of filamentous bacteria, the increase of EPS and the decrease of shear stress led to the formation of large and irregular flocs. Furthermore, the mixed liquid suspended solids (MLSS) concentration and sludge viscosity increased significantly as HRT decreased. The results also indicated that sludge viscosity was the predominant factor that affecting hydrodynamic conditions of MBR systems.     

Two-stage anaerobic digestion of biodegradable municipal solid waste using a rotating drum mesh filter bioreactor and anaerobic filter

A rotating drum mesh filter bioreactor (RDMFBR) with a 100 μm mesh coupled to an anaerobic filter was used for the anaerobic digestion of biodegradable municipal solid waste (BMW). Duplicate systems were operated for 72 days at an organic loading rate (OLR) of 7.5 gVS l⁻¹ d⁻¹. Early in the experiment most of the methane was produced in the 2nd stage. This situation gradually reversed as methanogenesis became established in the 1st stage digester, which eventually produced 86–87% of the total system methane. The total methane production was 0.2 l g⁻¹ VS_added with 60–62% volatile solids destruction. No fouling was experienced during the experiment at a transmembrane flux rate of 3.5 l m⁻² h⁻¹. The system proved to be robust and stably adjusted to a shock loading increase to 15 gVS l⁻¹ d⁻¹, although this reduced the overall methane production to 0.15 l g⁻¹ VS_added.     

Performance of a membrane bioreactor used for the treatment of wastewater contaminated with heavy metals

In this work the performance of a Membrane bioreactor (MBR) was assessed for the removal of 3-15 mg/l of copper, lead, nickel and zinc from wastewater. The average removal efficiencies accomplished by the MBR system were 80% for Cu(II), 98% for Pb(II), 50% for Ni(II) and 77% for Zn(II). The addition of 5 g/l vermiculite into the biological reactor enhanced metal removal to 88% for copper, 85% for zinc and 60% for nickel due to adsorption of metal ions on the mineral, while it reduced biomass inhibition and increased biomass growth. The metal ions remaining in soluble form penetrated into the permeate, while those attached to sludge flocs were effectively retained by the ultrafiltration membranes. The average heterotrophic biomass inhibition was 50%, while it reduced to 29% when lower metal concentrations were fed into the reactor in the presence of vermiculite. The respective autotrophic biomass inhibition was 70% and 36%. The presence of heavy metals and vermiculite in the mixed liquor adversely impacted on membrane fouling.     

Lab-scale study of an anaerobic membrane bioreactor (AnMBR) for dilute municipal wastewater treatment

Anaerobic bioreactors supplemented with membrane technology have become quite popular, owing to their favorable energy recovery characteristics. In this study, a lab-scale anaerobic Membrane Bioreactor (AnMBR) was assessed in experimental treatments of pre-settled dilute municipal wastewater obtained from a full-scaled wastewater treatment plant. The MBR system was operated in continuous flow mode for 440 days. To evaluate the performance of the AnMBR under various loading rates, the hydraulic retention time (HRT) was reduced in a stepwise manner (from 2 to 0.5 days). Afterward, the mixed liquor suspended solids (MLSS) were reduced from 7,000 to 3,000 mg/L in increments of 1,000 mg/L, resulting in a decrease in solids retention time (SRT) at a constant HRT of 1.0 day. The soluble chemical oxygen demand (SCOD) concentration in the feed varied between 38 and 131 mg/L, whereas the average permeate SCOD ranged between 18 and 37 mg/L, reflecting excellent effluent quality. The AnMBR performance in terms of COD removal proved stable, despite variations in influent characteristics and HRT and SRT changes. The concentration of extracellular polymeric substance (EPS) was reduced with decreases in HRT from 42 to 22 mg VS/mg of MLSS, thereby indicating that the increased biomass concentration biodegraded the EPS at lower HRTs. AnMBR is, therefore, demonstrably a feasible option for the treatment of dilute wastewater with separate stage nitrogen and phosphorus removal processes.     

Integration of aerobic granular sludge and membrane bioreactors for wastewater treatment

Environmental deterioration together with the need for water reuse and the increasingly restrictive legislation of water quality standards have led to a demand for compact, efficient and less energy consuming technologies for wastewater treatment. Aerobic granular sludge and membrane bioreactors (MBRs) are two technologies with several advantages, such as small footprint, high-microbial density and activity, ability to operate at high organic- and nitrogen-loading rates, and tolerance to toxicity. However, they also have some disadvantages. The aerobic granular sludge process generally requires post-treatment in order to fulfill effluent standards and MBRs suffer from fouling of the membranes. Integrating the two technologies could be a way of combining the advantages and addressing the main problems associated with both processes. The use of membranes to separate the aerobic granules from the treated water would ensure high-quality effluents suitable for reuse. Moreover, the use of granular sludge in MBRs has been shown to reduce fouling. Several recent studies have shown that the aerobic granular membrane bioreactor (AGMBR) is a promising hybrid process with many attractive features. However, major challenges that have to be addressed include how to achieve granulation and maintain granular stability during continuous operation of reactors. This paper aims to review the current state of research on AGMBR technology while drawing attention to relevant findings and highlight current limitations.     

Bacterial community structure and enzyme activities in a membrane bioreactor (MBR) using pure oxygen as an aeration source

A pilot-scale membrane bioreactor was used to treat urban wastewater using pure oxygen instead of air as a source of aeration, to study its influence on bacterial diversity and levels of enzyme activities (acid and alkaline phosphatases, glucosidase, protease, and esterase) in the sludge. The experimental work was developed in two stages influenced by seasonal temperature. Operational parameters (temperature, pH, BOD₅, COD, total and volatile suspended solids) were daily monitored, and enzyme activities measured twice a week. Redundancy analysis (RDA) was used to reveal relationships between the level of enzyme activities and the variation of operational parameters, demonstrating a significant effect of temperature and volatile suspended solids. Bacterial diversity was analyzed by temperature-gradient gel electrophoresis of PCR-amplified partial 16S rRNA genes. Significant differences in community structure were observed between both stages. Sequence analysis revealed that the prevalent Bacteria populations were evolutively close to Alphaproteobacteria (44%), Betaproteobacteria (25%) and Firmicutes (17%).