Method for printing functional protein microarrays

Piezoelectric dispensing of proteins from borosilicate glass capillaries is a popular method of protein biochip fabrication that offers the advantages of sample recovery and noncontact with the printing substrate. However, little regard has been given to the quantitative aspects of dispensing minute volumes (1 nL or less) at the low protein concentrations (20 micrograms/mL or less) typically used in microprinting. Specifically, loss of protein sample due to nonspecific adsorption to the glass surface of the dispensing capillaries can limit the amount of protein delivered to the substrate. We demonstrate the benefits of a low ionic strength buffer containing the carrier protein BSA that effectively minimizes the ionic strength-dependent phenomenon of nonspecific protein adsorption to borosilicate glass. Over the concentration range of 20-2.5 micrograms/mL, the dispensing of a reference IgG in 10 mM PBS including 0.1% BSA resulted in the deposition of 3.6- to 44-fold more IgG compared to the deposition of IgG in standard 150 mM PBS in the absence of BSA. Furthermore, when the IgG was dispensed with carrier protein, the resulting spots exhibited a more uniform morphology. In a direct immunoassay for cholera toxin, capture antibody spots dispensed in 10 mM PBS containing 0.1% BSA produced fluorescent signals that were 2.8- to 4.3-fold more intense than antibody spots that were dispensed in 150 mM PBS without BSA. Interestingly, no differences were observed in the specific activities of the capture antibodies as a result of printing in the different buffers. The implications of these results on the future development of protein biochips are discussed.     

Estrogen and Progesterone Receptors in the Uterus of the Vervet Monkey

Abstract

Experimental conditions for the optimal measurement of estrogen (ER) and progesterone (PR) receptors in normal vervet monkey (Cercopithecus aethiops pygerythrus) uteri are described. The uteri of this primate were found to contain relatively high concentrations of both ER and PR. Levels of ER ranged from 151 to 822 femtomoles per mg protein (mean for group assayed is 327±165 femtomoles per mg protein). PR assays were performed on the same cytosols and the levels ranged from 444 to 2267 femtomoles per mg protein (mean of 1285±511 femtomoles per mg protein). Mean K_d values for the ER- and PR-ligand complexes were found to be 3.15±1.4x10^-10 M and 2.38±0.2x10^-9 M respectively, within the group analysed (n=21). The ratio of PR to ER varied between 1.1 and 13.1 with a mean of 4.5±2.4. Ligand specificity studies revealed that [³H]-17β-estradiol binding to the ER could only be inhibited by estrogens or estrogen analogues. The PR however exhibited an affinity for a wider range of ligand types. In low ionic strength buffers both ER and PR sedimented as ±8S type molecules in the presence or absence of 10mM sodium molybdate. Both receptors dissociated into smaller components, following a short exposure to 0.4 M KCl and subsequent centrifugation in a gradient containing 0.4 M KCl.     

Cosedimentation of pea root polysomes with the cytoskeleton.

When conventional, high ionic strength buffers were used for the isolation of polysomes from pea roots, only about 10% were retained in the detergent-insoluble pellet, and they were not degraded by endogenous RNase. A low ionic strength, cytoskeleton-stabilizing buffer increased retention to 60%, but polysomes were severely degraded. The RNase inhibitors, ribonucleoside-vanadyl complexes, heparin, KCl and ammonium sulphate lessened degradation but caused release, while Tris-HCl at 15-25 mM was able to prevent degradation without causing release. Cosedimentation of polysomes with the cytoskeleton is not an artefact of adsorption or trapping since isolated polysomes labelled through their nascent polypeptides and added to unfractionated tissue were not retained in the cytoskeletal pellet.     

A kinetic analysis of the estrogen receptor transformation.

The rate of the 4 to 5 S estrogen-binding protein (EBP) in vitro transformation was measured by sucrose gradient centrifugation analysis. The temperature-activated 4 to 5 S EBP transformation is found to be highly reproducible without loss of [3H]estradiol-binding activity in a buffer containing an excess of [3H]estradiol, 40 mM Tris, 1 mM dithiothreitol, and 1 M urea at pH 7.4. The presence of [3H]estradiol is necessary for the 4 to 5 EBP transformation. A kinetic analysis of the 4 to 5 EBP transformation shows that it is a bimolecular reaction, the dimerization of the 4 S EBP with a second (similar or dissimilar) monomer or subunit. In buffers containing 0.4 M KCl the apparent second order rate constant is 2.3 plus or minus 0-2 times 10-7 M minus 1 min minus 1 at 28 degrees. The reaction is independent of the initial receptor concentration, suggesting that the 4 S EBP is dissociated into monomeric units in buffers of high ionic strength. In buffers without KCl or with 0.1 M KCl the apparent second order rate constant of receptor transformation increases with decreasing receptor concentration. This suggests that the 4 S EBP is associated weakly with another macromolecule (or macromolecules) in buffers of low ionic strength. The rate of 4 to 5 S EBP transformation shows a 200-fold increase between 0 and 35 degrees. The Arrhenius energy of activation is 21.3 kcal mol minus 1 in buffer without KCl and 19.1 kcal mol minus 1 in buffer with 0.4 M KCl. Following the temperature-activated dimerization, the avidity of binding between the 4 S EBP and its complementary subunit is increased, 0.4 M KCl can no longer cause dissociation, and the 5 S EBP dimer appears. This kinetic analysis indicates that the avidity of binding between the subunits of the estrogen receptor is modulated by estradiol, temperature, and ionic strength. We propose that these interactions of the estrogen receptor's subunits reflect conformational changes involved in receptor activation.     

Comparative study of the iron-binding properties of human transferrins: I. Complete and sequential iron saturation and desaturation of the lactotransferrin

Human lactotransferrin binds 2 Fe³⁺ tightly at two specific sites. In order to demonstrate differences between the stability of the two iron-binding sites, the removal of iron was studied in buffers in the pH range 8-3 varying the ionic strength and with or without metal chelators such as phosphate ions and EDTA.The results show that in the presence of formate and acetate buffers of ionic strength 0.1–0.4 and in a pH range of 5–3, the two Fe³⁺ from human lactotransferrin are removed stimultaneously.Addition of 4 mM EDTA to buffers of ionic strength 0.1 and in the pH range 8–3 shows that between pH 5–4.3 the iron from only one of the binding sites, called the ‘acid labile’ site, is removed.Addition of 0.2 M phosphate ions to buffers of ionic strength 0.2 and in pH range 8–3 containing 4 mM EDTA shows that Fe³⁺ from the ‘acid labile’ site may be completely removed at pH 6. Removal of Fe³⁺ from the ‘acid stable’ site is obtained at pH 4.The differential behavior of the two iron binding sites was also shown by saturation experiments in the presence of citrate/bicarbonate buffers at different pH values. In a pH range 6.2–4.8, 50% saturation was obtained, but at pH 6.35 complete saturation was achieved. When saturation of partially saturated samples of human lactotransferrin was performed with ⁵⁹Fe it was demonstrated that in the pH range 6.2–4.8 iron is bound only to the ‘acid labile’ site.     

Dynamic behavior of adsorber membranes for protein recovery

In recent years there has been a considerable interest in developing membrane chromatography systems that function as a short, wide chromatographic column in which the adsorptive packing consists of one or more microporous membranes. This study reports the use of new adsorber membranes prepared by the incorporation of various types of ion exchange resins into an EVAL porous membrane for protein recovery. The obtained heterogeneous matrixes composed of solid particles surrounded by the polymeric film possess a good accessibility for the protein to the adsorptive sites. Furthermore, small particles can be embedded into porous polymeric structures without the disadvantages of classical chromatographic columns (high pressure drop, fouling and plugging sensitivity, low flow rate), but with the advantages of membrane technology (easy scale-up, low-pressure drop, high flow rate). The adsorptive membranes feature high static as well as dynamic protein adsorption capacities for operating flow rates ranging from 200 to 400 L h bar per m(2) and ionic strength of 20-200 mM. In a sequential desorption step by changing the pH and/or the ionic strength of the eluent, up to 90% protein recovery was obtained. Next to the separation, the mixed matrix adsorber membrane functions as a concentration medium since the protein can be concentrated up to 20-fold in the eluent. The adsorber membranes can be reused in multiple adsorption/desorption cycles with good adsorption performances.     

Relationship of hemolysis buffer structure, pH and ionic strength to spontaneous contour smoothing of isolated erythrocyte membranes

Isolated human erythrocyte membranes crenate when suspended in isotonic medium, but can use MgATP to reduce their net positive curvature, yielding smooth discs and cup forms that eventually undergo endocytosis. An earlier report from this laboratory (Patel, V.P. and Fairbanks, G. (1981) J. Cell Biol. 88, 430-440), has described a phenomenon of ATP-independent shape change in which ghosts prepared by hemolysis and washing in synthetic zwitterionic buffers crenated at 0 degree C, but underwent conversion to smooth discs and cups when warmed in the absence of MgATP. We have further explored the effect of the hemolysis condition on the requirement for ATP in ghost shape change. 25 hemolysis buffers were applied at 10 mM (pH 7.4, 0 degree C). Eight anionic buffers with relatively high ionic strength (e.g., phosphate and diethylmalonic acid (DMA] yielded ghosts requiring ATP for shape change, while two cationic buffers (Bistris and imidazole) and ten synthetic zwitterionic buffers (e.g., Tricine and Hepes) with lower ionic strength produced ghosts that smoothed spontaneously at 30 degrees C. Hemolysis at intermediate ionic strength yielded mixed populations in which spontaneous smoothing was expressed in all-or-none fashion. Maximal ATP-independent shape change was induced by hemolysis at pH 7.3-7.7, while ATP was required after hemolysis at pH less than or equal to 7.1 even when the ionic strength at hemolysis was low. Ghosts requiring ATP could be converted to ATP independence by washing at low ionic strength, but ATP independence could not be reversed readily by washing at high ionic strength. Exposure to low ionic strength at pH greater than 7.1 presumably changes membrane organization in a way that alters the temperature dependence of tensions within the bilayer or skeleton of the composite membrane.     

Biophysical studies on the lipid transfer particle from the hemolymph of the tobacco hornworm, Manduca sexta

Hydrodynamic studies conducted in the analytical ultracentrifuge provided evidence for two populations of lipid transfer particle (LTP) when centrifuged in a buffer solution containing 10 mM Tris, pH 8.0/100 mM KCl. The apparent sedimentation coefficients of the two species was 23.3 S and 15.3 S. Upon changing the buffer pH to 7.0 or 5.7, two species of LTP were still present but the ratio of their relative abundance was altered. When the KCl concentration in the buffer was lowered to 50 mM the sample sedimented as a single species with an apparent S20,w of 22.9 S. In higher ionic strength buffers (10 mM succinate, pH 5.7/500 mM KCl) LTP sedimented with an apparent S20,w of 14.8 S. Further experiments revealed that these two forms are interconvertable as a function of buffer ionic strength. Given previous estimates of the molecular size of LTP we concluded that the slower sedimenting peak observed at high ionic strength represents monomeric LTP while the faster sedimenting material observed at low ionic strength is likely to be an aggregated state of LTP. This interpretation is supported by molecular weight determinations made by sedimentation equilibrium experiments conducted in 10 mM succinate, pH 5.7/500 mM KCl which yielded a particle Mr = 887,000. Circular dichroism spectra of monomeric LTP sample revealed 6% alpha-helix, 49% beta-sheet, 7% beta-turn and 35% random coil while aggregated LTP contained 13% alpha-helix, 66% beta-sheet and 21% random coil. The transfer activity of the two LTP forms was assayed and found to be the same indicating that either the state of LTP aggregation did not affect transfer activity or that upon exposure to a large excess of lipoprotein substrate disaggregation, without loss of activity, occurs.     

Binding of horse heart cytochrome c to yeast porphyrin cytochrome c peroxidase: a fluorescence quenching study on the ionic strength dependence of the interaction

The binding of horse heart cytochrome c to yeast cytochrome c peroxidase in which the heme group was replaced by protoporphyrin IX was determined by a fluorescence quenching technique. The association between ferricytochrome c and cytochrome c peroxidase was investigated at pH 6.0 in cacodylate/KNO3 buffers. Ionic strength was varied between 3.5 mM and 1.0 M. No binding occurs at 1.0 M ionic strength although there was a substantial decrease in fluorescence intensity due to the inner filter effect. After correcting for the inner filter effect, significant quenching of porphyrin cytochrome c peroxidase fluorescence by ferricytochrome c was observed at 0.1 M ionic strength and below. The quenching could be described by 1:1 complex formation between the two proteins. Values of the equilibrium dissociation constant determined from the fluorescence quenching data are in excellent agreement with those determined previously for the native enzyme-ferricytochrome c complex at pH 6.0 by difference spectrophotometry (J. E. Erman and L. B. Vitello (1980) J. Biol. Chem. 225, 6224-6227). The binding of both ferri- and ferrocytochrome c to cytochrome c peroxidase was investigated at pH 7.5 as functions of ionic strength in phosphate/KNO3 buffers using the fluorescence quenching technique. The binding in independent of the redox state of cytochrome c between 10 and 20 mM ionic strength, but ferricytochrome c binds with greater affinity at 30 mM ionic strength and above.     

Ionic and nucleotide requirements for microtubule polymerization in vitro.

The ionic and nucleotide requirements for the in vitro polymerization of microtubules from purified brain tubulin have been characterized by viscometry. Protein was purified by successive cycles of a temperature dependent assembly-diassembly scheme. Maximal polymerization occurred at a concentration of 0.1 M Pipes (piperazine-N,N'-bis(2-ethanesulfonic acid)); increasing ionic strength by addition of NaCl to samples prepared in lower buffer concentrations did not result in an equivalent level of polymerization. Both Na-+ and K-+ inhibited microtubule formation at levels greater than 240 mM, withmaximal assembly occurring at physiological concentrations of 150 mM. Maximal extent of assembly occurred at pH 6.8 and optimal rate at pH 6.6. Inhibition of polymerization was half-maximal at added calcium concentrations of 1.0 mM and magnesium concentrations of 10.0 mM. EGTA (ethylene glycol bis(beta-aminoethyl ether)tetraacetic acid), which chelates Ca-2+, had no effect on polymerization over a concentration range of 0.01-10.0 mM. In contrast, EDTA (ethylenediaminetetraacetic acid), which chelates both Mg-2+ and Ca-2+, inhibited assemble half-maximally at 0.25 mM and totally at 2.0 mM. As determined from experiments using Mg-2+-EDTA buffers, magnesium was required for polymerization. Magnesium promoted the maximal extent of assembly at substoichiometric levels relative to tubulin, but was maximal for both rate and extent at stoichiometric concentrations. Elemental analyses indicated that approximately 1 mol of magnesium was tightly bound/mol of tubulin dimer. Viscosity development was dependent upon hydrolyzable nucleoside triphosphate, and stoichiometric levels of GTP were sufficient for maximal polymerization. The effect of magnesium in increasing the rate of GTP-dependent polymerization suggests that a Mg-2+-GTP complex is the substrate required for a step in assembly.     

Separation of the epithelial and mesenchymal components of the newt limb regenerate with salt.

After incubation of isolated forelimb regenerates of Notophthalmus (Triturus) viridescens at all developmental stages for 60 minutes at 37 degrees C in a salt medium containing 111 mM sodium chloride, 5.6 mM potassium chloride and 100 mM sodium phosphate buffer at pH 7.5, the wound epithelium of each regenerate was removed intact from its underlying mesenchymal component. The suggestion is made that the salt medium is an effective epithelial-mesenchymal separating agent due to a combination of its hypertonicity, high ionic strength and the fact that the medium precipitates calcium as calcium phosphate. Attempts to dissect away the epithelium from the mesenchyme after incubation of isolated regenerates in sodium phosphate containing 1% or 3% Difco 1:250 trypsin, 10 mM EDTA or 150 units collagenase/ml medium were unsuccessful. Epidermis of adult newt forelimb skin was removed only after extended incubation of the forelimbs in the salt medium for three hours at 37 degrees C or after freezing isolated forelimbs in buffer and subsequent thawing.     

Micelles of cerebroside sulphate

The critical micelle concentration of cerebroside sulphate in water is 0-01 mM: it increases with increasing concentrations of buffer to 0-07 mM in 0-1 M sodium acetate and formate buffers, pH 5-6 and 4-5 respectively. The partial specific volume of the micelles is about 0-94. The behaviour of the micelles in the ultracentrifuge and on Sephadex G-200 shows them to be grossly heterogeneous with respect to size. In 0-1 M buffer s20,w is about 26 S; in water or 0-01 M buffer smaller micelles with an s20,w of about 6 S are also present. In 0-01 M formate, pH 4-5, the smallest species detectable by equilibrium ultracentrifugation had a micellar weight of about 180,000 corresponding to an aggregation number of about 180. Much larger aggregates were also present. It is suggested that the smallest micelles are the substrate for sulphatase A when this is acting as a cerebroside sulphatase in buffers of low ionic strength.     

Direct calorimetric analysis of the enzymatic activity of yeast cytochrome c oxidase.

The kinetic and thermodynamic parameters associated with the enzymatic reaction of yeast cytochrome c oxidase with its biological substrate, ferrocytochrome c, have been measured by using a titration microcalorimeter to monitor directly the rate of heat production or absorption as a function of time. This technique has allowed determination of both the energetics and the kinetics of the reaction under a variety of conditions within a single experiment. Experiments performed in buffer systems of varying ionization enthalpies allow determination of the net number of protons absorbed or released during the course of the reaction. For cytochrome c oxidase the intrinsic enthalpy of reaction was determined to be -16.5 kcal/mol with one (0.96) proton consumed for each ferrocytochrome c molecule oxidized. Activity measurements at salt concentrations ranging from 0 to 200 mM KCl in the presence of 10 mM potassium phosphate, pH 7.40, and 0.5 mM EDTA display a biphasic dependence of the electron transferase activity upon ionic strength with a peak activity observed near 50 mM KCl. The ionic strength dependence was similar for both detergent-solubilized and membrane-reconstituted cytochrome c oxidase. Despite the large ionic strength dependence of the kinetic parameters, the enthalpy measured for the reaction was found to be independent of ionic strength. Additional experiments involving direct transfer of the enzyme from low to high salt conditions produced negligible enthalpy changes that remained constant within experimental error throughout the salt concentrations studied (0-200 mM KCl). These results indicate that the salt effect on the enzyme activity is of entropic origin and further suggest the absence of a major conformational change in the enzyme due to changes in ionic strength.(ABSTRACT TRUNCATED AT 250 WORDS)     

Analysis of hSCOMT adsorption in bioaffinity chromatography with immobilized amino acids: the influence of pH and ionic strength

In the last years, chromatographic supports with amino acids as immobilized ligands (AAILs) were been used successfully for isolation of several biomolecules, such as proteins. In this context and based on specific properties of human soluble cathecol-O-methyltransferase (hSCOMT), we screened and analyzed the effect of experimental conditions, such as pH and ionic strength manipulation for hSCOMT adsorption, over six different AAIL commercial supports. Typically, the proteins adsorption on AAIL chromatographic supports is around their pI. While hSCOMT isoelectric point is around 5.5, this parameter leads us to design new adsorption strategies with several acid buffers for the chromatographic process. In terms of the ionic strength manipulation strategy, the results suggest that the AAILs-hSCOMT interaction is strongly affected by the intrinsic hSCOMT hydrophobic domains. On the other hand, the interaction mechanism of hSCOMT on amino acid resins appears to be highly dependent on the binding pH. Consequently the retention mechanism of the target enzyme on the AAILs can be as either in typical hydrophobic or ionic chromatographic supports, so long as selecting various mobile phases and separation conditions. In spite of these mixed-mode interactions and operation strategies, the elution of interferent's proteins from recombinant host can be achieved only with suitable adjusts in pH mobile phase set point. This lead to a new approach in biochromatographic COMT retention, while possess a higher specificity than other chromatographic methods reported in literature.     

Adsorption of glyceraldehyde 3-phosphate dehydrogenase on condensed monolayers of phospholipid.

The adsorption of [14C] alkylated glyceraldehyde 3-phosphate dehydrogenase from rabbit muscle to condensed monolayers of phosphatidic acid was investigated under a variety of conditions. 2. The rate constant for association at 20 degrees C depended on ionic strength. At I/2=60mM the rate constant was 0.39min-1. At I/2=260mM it decreased to 0.27min-1. 3. The apparent association constant (Kass.) for adsorption at I/2=60mM was 1.06 X 10(6)M-1 and was strongly influenced by subphase changes in pH and ionic strength. Measurements of Kass. at 20 degrees and 5 degrees C gave a value for the apparent enthalpy change on adsorption of -33kJ-mol-1. Calculations of the apparent change in free energy and apparent entropy change for the adsorption process gave values of -34kJ-mol-1 and +2J-K-1-mol-1 respectively. 4. Decreasing the amount of phosphatidic acid in the monolayer by replacement with phosphatidylcholine caused the shape of the adsorption isotherm to change from apparent hyperbolic to sigmoid. Subphase changes in pH or ionic strength did not affect the shape of the adsorption isotherm. However, adsorption of enzyme on monolayers of 100% phosphatidic acid in the presence of 1mM-CaCl2 was sigmoid in nature. 5. It is concluded that glyceraldehyde 3-phosphate dehydrogenase binds to condensed charged monolayers by multiple electrostatic interactions. At low concentrations of phosphatidic acid in the monolayer or in the presence of Ca2+, this occurs in a two-step process and depends on lateral diffusion of phosphatidic acid for strong binding to take place.     

Effect of Ionic Strength on the Binding of Sindbis Virus to Chick Cells

Sindbis virus can adsorb to chicken embryo fibroblasts in two different ways. "Loosely" bound virus can be washed off the cell with buffers of ionic strength 0.2 or greater, whereas "tightly" bound virus remains attached under these conditions. When Sindbis virus is adsorbed to chick cells at 4 C from a buffer of ionic strength 0.17, 40 to 50% of the adsorbed virus is loosely bound, the remainder tightly bound. Infection of chick cells by Sindbis virus has only small effects on the total amount of virus that can be bound to the cells. However, the amount of Sindbis virus that can be tightly bound declines rapidly beginning at 2 to 3 h after infection. By 7 h after infection, the amount of virus that can be tightly bound is only 10 to 20% of the amount bound to uninfected cells. The adsorption (and penetration) of virus at 37 C is most efficient at an ionic strength of 0.15 to 0.17; at this ionic strength most of the adsorbed virus is tightly bound. At higher ionic strengths the virus adsorbs poorly. At lower ionic strengths most of the virus is loosely bound. A second enveloped virus, vesicular stomatitis virus, has been studied for the purposes of comparison; its adsorption behavior differs from that of Sindbis virus.     

Membrane adenosine triphosphatase of Micrococcus lysodeikticus: effect of millimolar Mg2+ in modulating the properties of the membrane-bound enzyme

The latency of Micrococcus lysodeikticus membrane-bound Mg(2+)-adenosine triphosphatase (ATPase) is expressed by the ratio of its activity assayed in the presence of trypsin ("total") versus the activity assayed in absence of the protease ("basal"). By isolating membranes in the presence of variable concentrations of Mg(2+) (50 mM, 10 mM, or none) and by washing them with different Mg(2+)- and ethylenediaminetetraacetic acid-containing tris(hydroxymethyl)aminomethane-hydrochloride buffers (pH 7.5), we showed that the enzyme latency was dependent on the environmental concentration of this divalent metal ion. Mg(2+) bound to at least two classes of sites. The binding of Mg(2+) to low-affinity sites (saturation at approximately 40 mM external Mg(2+)) induced a high basal ATPase activity, whereas its binding to medium-affinity sites (saturation at about 2 mM Mg(2+)) correlated with low basal activity and a very high stimulation by trypsin. Membranes with tightly bound Mg(2+) (high affinity?) revealed an intermediate behavior for the latency of M. lysodeikticus ATPase. The Mg(2+)/Ca(2+) antagonism as activators of the membrane ATPase was not directly related to Mg(2+) binding by the membranes. The efficiency of the ATPase release from M. lysodeikticus membrane by 3 mM tris(hydroxymethyl)aminomethane-hydrochloride buffer (pH 7.5) was inversely proportional to the concentration of external and/or bound Mg(2+). Deoxycholate (DOC) (1%) solubilized the ATPase from all types of membrane. All the soluble ATPases behaved as Ca(2+)-ATPases, but the DOC-soluble fractions showed degrees of latency like those of the original membranes. The DOC-soluble ATPase preparation revealed a vesicular structure and complex protein patterns by sodium dodecyl sulfate gel electrophoresis. We propose that ATPase latency is modulated via a Mg(2+)-ATPase-membrane complex.     

Membrane ATPase of Escherichia coli K 12 Selective solubilization of the enzyme and its stimulation by trypsin in the soluble and membrane-bound states

ATPase (EC 3.6.1.3) of Escherichia coli has been solubilized from two morphologically distinct membranes (vesicles and “ghosts”). Maximum ATPase release is attained with 3 mM EDTA in NH₄HCO₃, pH 9.0, and depends on protein concentration. After solubilization, the total enzyme activity is increased by 300% with respect to the membrane-bound enzyme. The released soluble ATPase accounts for more than 90% of this activity. Its specific activity is at least 10 times higher than the original value. Membrane treatment with buffers of various ionic strengths without EDTA and detergents is less selective. The molecular sieving properties (gel electrophoresis and Sephadex G-200 filtration) confirm the soluble nature of the preparation. A molecular weight close to 300 000 has been estimated for it.The membrane-bound ATPase is stimulated by trypsin by 70–100%. Most of the soluble ATPase maintains a trypsin activation of the same order. Exceptions are the preparations obtained at high protein dilution and extracted with sodium dodecyl sulphate and deoxycholate. The soluble ATPase is more labile than the membrane-bound enzyme. Its sensitivity to different temperatures depends upon protein concentration and pH during storage. Inactivation seems to result from dissociation and/or proteolysis.We suggest an ATPase link to the membrane through ionic divalent cation bridges. We also suggest that the enzyme possesses self-regulatory properties which would account for trypsin stimulation.     

Calcium sensitivity of vertebrate skeletal muscle myosin

The calcium sensitivity of vertebrate skeletal muscle myosin has been investigated. Adenosinetriphosphatase (ATPase) activity was assayed in a reconstituted system composed of either purified rabbit myosin plus actin or myosin plus actin, tropomyosin, and troponin. The calcium sensitivity of actomyosin Mg-ATPase activity was found to be directly affected by the ionic strength of the assay medium. Actomyosin assayed at approximately physiological ionic strength (120 mM KCl) demonstrated calcium sensitivity which varied between 6 and 52%, depending on the myosin preparation and the age of the myosin. Mg-ATPase activity was increased when calcium was present in the assay medium at physiological ionic strength. Conversely, actomyosin Mg-ATPase activity assayed at a lower ionic strength (15 mM KCl) was inhibited by addition of calcium. Addition of tropomyosin and troponin to the assay increased the calcium sensitivity of the system at the physiological ionic strength still further (up to 99% calcium sensitivity) and conferred calcium sensitivity on the system at the lower ionic strength (greater than 90% calcium sensitivity). A correlation also existed between myosin's calcium sensitivity and the phosphorylated state of light chain 2.