Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

A new weak electron‐deficient building block, bis(2‐ethylhexyl) 2,5‐bis(5‐bromothiophen‐2‐yl) thieno[3,2‐b]thiophene‐3,6‐dicarboxylate ( TT‐Th ), is incorporated to construct a wide‐bandgap (1.88 eV) polymer PBDT‐TT for nonfullerene polymer solar cells (NF‐PSCs). PBDT‐TT possesses suitable energy levels and complementary absorption when blended with both ITIC analogues ( ITIC and IT‐M ) and a near‐infrared (NIR) acceptor ( 6TIC ). Moreover, PBDT‐TT exhibits good conjugated planarity and preferable face‐on orientation in the blended thin film, which are beneficial for charge transfer and carrier transport. The PSCs based on PBDT‐TT : IT‐M and PBDT‐TT : 6TIC blend films yield high power conversion efficiencies of 11.38% and 11.03%, respectively. To the best of the authors' knowledge, the PCE of 11.03% for PBDT‐TT : 6TIC‐ based device is one of the highest values reported for NIR NF‐PSCs. This work demonstrates that TT‐Th is a useful new electron‐accepting building block for making p‐type wide bandgap polymers for efficient NIR NF‐PSCs.     

Wide‐Bandgap Perovskite/Gallium Arsenide Tandem Solar Cells

Gallium arsenide (GaAs) photovoltaic (PV) cells have been widely investigated due to their merits such as thin‐film feasibility, flexibility, and high efficiency. To further increase their performance, a wider bandgap PV structure such as indium gallium phosphide (InGaP) has been integrated in two‐terminal (2T) tandem configuration. However, it increases the overall fabrication cost, complicated tunnel‐junction diode connecting subcells are inevitable, and materials are limited by lattice matching. Here, high‐efficiency and stable wide‐bandgap perovskite PVs having comparable bandgap to InGaP (1.8–1.9 eV) are developed, which can be stable low‐cost add‐on layers to further enhance the performance of GaAs PVs as tandem configurations by showing an efficiency improvement from 21.68% to 24.27% (2T configuration) and 25.19% (4T configuration). This approach is also feasible for thin‐film GaAs PV, essential to reduce its fabrication cost for commercialization, with performance increasing from 21.85% to 24.32% and superior flexibility (1000 times bending) in a tandem configuration. Additionally, potential routes to over 30% stable perovskite/GaAs tandems, comparable to InGaP/GaAs with lower cost, are considered. This work can be an initial step to reach the objective of improving the usability of GaAs PV technology with enhanced performance for applications for which lightness and flexibility are crucial, without a significant additional cost increase.     

15% Efficiency Tandem Organic Solar Cell Based on a Novel Highly Efficient Wide‐Bandgap Nonfullerene Acceptor with Low Energy Loss

A tandem organic solar cell (OSC) is a valid structure to widen the photon response range and suppress the transmission loss and thermalization loss. In the past few years, the development of low‐bandgap materials with broad absorption in long‐wavelength region for back subcells has attracted considerable attention. However, wide‐bandgap materials for front cells that have both high short‐circuit current density (J_SC) and open‐circuit voltage (V_OC) are scarce. In this work, a new fluorine‐substituted wide‐bandgap small molecule nonfullerene acceptor TfIF‐4FIC is reported, which has an optical bandgap of 1.61 eV. When PBDB‐T‐2F is selected as the donor, the device offers an extremely high V_OC of 0.98 V, a high J_SC of 17.6 mA cm^?2, and a power conversion efficiency of 13.1%. This is the best performing acceptor with such a wide bandgap. More importantly, the energy loss in this combination is 0.63 eV. These properties ensure that PBDB‐T‐2F:TfIF‐4FIC is an ideal candidate for the fabrication of tandem OSCs. When PBDB‐T‐2F:TfIF‐4FIC and PTB7‐Th:PCDTBT:IEICO‐4F are used as the front cell and the back cell to construct tandem solar cells, a PCE of 15% is obtained, which is one of best results reported to date in the field of organic solar cells.     

Organic Salts as a Route to Energy Level Control in Low Bandgap,High Open‐Circuit Voltage Organic and Transparent Solar Cells that Approach the Excitonic Voltage Limit

A new series of organic salts with selective near‐infrared (NIR) harvesting to 950 nm is reported, and anion selection and blending is demonstrated to allow for fine tuning of the open‐circuit voltage. Extending photoresponse deeper into the NIR is a significant challenge facing small molecule organic photovoltaics, and recent demonstrations have been limited by open‐circuit voltages much lower than the theoretical and practical limits. This work presents molecular design strategies that enable facile tuning of energy level alignment and open‐circuit voltages in organic salt‐based photovoltaics. Anions are also shown to have a strong influence on exciton diffusion length. These insights provide a clear route toward achieving high efficiency transparent and panchromatic photovoltaics, and open up design opportunities to rapidly tailor molecules for new donor–acceptor systems.     

Low Temperature Synthesis of Stable γ‐CsPbI3 Perovskite Layers for Solar Cells Obtained by High Throughput Experimentation

The structural phases and optoelectronic properties of coevaporated CsPbI₃ thin films with a wide range of [CsI]/[PbI₂] compositional ratios are investigated using high throughput experimentation and gradient samples. It is found that for CsI‐rich growth conditions, CsPbI₃ can be synthesized directly at low temperature into the distorted perovskite γ‐CsPbI₃ phase without detectable secondary phases. In contrast, PbI₂‐rich growth conditions are found to lead to the non‐perovskite δ‐phase. Photoluminescence spectroscopy and optical‐pump THz‐probe mapping show carrier lifetimes larger than 75 ns and charge carrier (sum) mobilities larger than 60 cm² V^?1 s^?1 for the γ‐phase, indicating their suitability for high efficiency solar cells. The dependence of the carrier mobilities and luminescence peak energy on the Cs‐content in the films indicates the presence of Schottky defect pairs, which may cause the stabilization of the γ‐phase. Building on these results, p–i–n type solar cells with a maximum efficiency exceeding 12% and high shelf stability of more than 1200 h are demonstrated, which in the future could still be significantly improved, judging on their bulk optoelectronic properties.     

Accelerated Optimization of TiO2/Sb2Se3 Thin Film Solar Cells by High‐Throughput Combinatorial Approach

Sb₂Se₃, a V₂‐VI₃ compound semiconductor, has attracted extensive research attention in photovoltaics due to its non‐toxicity, low cost and earth‐abundant constituents. Herein, a combinatorial approach to optimize the performance of TiO₂/Sb₂Se₃ thin film photovoltaics is employed. By simultaneously conducting a series of experiments in parallel rather than one after another, combinatorial strategy increases experimental throughput and reduces personnel costs. Key parameters such as TiO₂ thickness, post‐annealing temperature and Sb₂Se₃ thickness are identified as 65 nm, 450 °C and 850 nm through the combinatorial approach. Finally, in combination with (NH₄)₂S back surface cleaning, TiO₂/Sb₂Se₃ solar cells with 5.6% efficiency and decent stability are obtained, showcasing the power of high‐throughput strategy for accelerating the optimization of Sb₂Se₃ photovoltaics.     

The Introduction of Fluorine and Sulfur Atoms into Benzotriazole‐Based p‐Type Polymers to Match with a Benzotriazole‐Containing n‐Type Small Molecule: “The Same‐Acceptor‐Strategy” to Realize High Open‐Circuit Voltage

“The Same‐Acceptor‐Strategy” (SAS) adopts benzotriazole (BTA)‐based p‐type polymers paired with a new BTA based non‐fullerene acceptor BTA13 to minimize the trade‐off between the open‐circuit voltage (V_OC) and short circuit current (J_SC). The fluorination and sulfuration are introduced to lower the highest occupied molecular orbitals (HOMO) of the polymers. The fluorinated polymer of J52‐F shows the higher power conversion efficiency (PCE) of 8.36% than the analog polymer of J52, benefited from a good balance between an improved V_OC of 1.18 V and a J_SC of 11.55 mA cm^?2. Further adding alkylthio groups on J52‐F, the resulted polymer, J52‐FS, exhibits the highest V_OC of 1.24 V with a decreased energy loss of 0.48 eV, compared with 0.67 eV for J52 and 0.54 eV for J52‐F. However, J52‐FS shows an inferior PCE (3.84%) with a lower J_SC of 6.74 mA cm^?2, because the small ΔE_HOMO between J52‐FS and BTA13 (0.02 eV) gives rise to the inefficient hole transfer and high charge recombination, as well as low carrier mobilities. The results of this study clearly demonstrate that the introduction of different atoms in p‐type polymers is effective to improve the SAS and realize the high (V_OC) and PCE.     

Perovskite Solar Cells on the Way to Their Radiative Efficiency Limit – Insights Into a Success Story of High Open‐Circuit Voltage and Low Recombination

Inorganic‐organic lead‐halide perovskite solar cells have reached efficiencies above 22% within a few years of research. Achieved photovoltages of >1.2 V are outstanding for a material with a bandgap of 1.6 eV – in particular considering that it is solution processed. Such values demand for low non‐radiative recombination rates and come along with high luminescence yields when the solar cell is operated as a light emitting diode. This progress report summarizes the developments on material composition and device architecture, which allowed for such high photovoltages. It critically assesses the term “lifetime”, the theories and experiments behind it, and the different recombination mechanisms present. It attempts to condense reported explanations for the extraordinary optoelectronic properties of the material. Amongst those are an outstanding defect tolerance due to antibonding valence states and the capability of bandgap tuning, which might make the dream of low‐cost highly efficient solution‐processed thin film solar cells come true. Beyond that, the presence of photon recycling will open new opportunities for photonic device design.     

High Throughput Discovery of Solar Fuels Photoanodes in the CuO–V2O5 System

Solar photoelectrochemical generation of fuel is a promising energy technology yet the lack of an efficient, robust photoanode remains a primary materials challenge in the development and deployment of solar fuels generators. Metal oxides comprise the most promising class of photoanode materials, but no known material meets the demanding requirements of low band gap energy, photoelectrocatalysis of the oxygen evolution reaction (OER), and stability under highly oxidizing conditions. Here, the identification of new photoelectroactive materials is reported through a strategic combination of combinatorial materials synthesis, high‐throughput photoelectrochemistry, optical spectroscopy, and detailed electronic structure calculations. Four photoelectrocatalyst phases, α ‐Cu₂V₂O₇, β ‐Cu₂V₂O_7, γ ‐Cu₃V₂O₈, and Cu₁₁V₆O₂₆, are reported with band gap energy at or below 2 eV. The photoelectrochemical properties and 30 min stability of these copper vanadate phases are demonstrated in three different aqueous electrolytes (pH 7, pH 9, and pH 13), with select combinations of phase and electrolyte exhibiting unprecedented photoelectrocatalytic stability for metal oxides with sub‐2 eV band gap. Through integration of experimental and theoretical techniques, new structure‐property relationships are determined and establish CuO–V₂O₅ as the most prominent composition system for OER photoelectrocatalysts, providing crucial information for materials genomes initiatives and paving the way for continued development of solar fuels photoanodes.     

Efficient Exploration of the Composition Space in Ternary Organic Solar Cells by Combining High‐Throughput Material Libraries and Hyperspectral Imaging

Organic solar cells based on ternary active layers can lead to higher power conversion efficiencies than corresponding binaries, and improved stability. The parameter space for optimization of multicomponent systems is considerably more complex than that of binaries, due to both, a larger number of parameters (e.g., two relative compositions rather than one) and intricate morphology–property correlations. Most experimental reports to date reasonably limit themselves to a relatively narrow subset of compositions (e.g., the 1:1 donor/s:acceptor/s trajectory). This work advances a methodology that allows exploration of a large fraction of the ternary phase space employing only a few (<10) samples. Each sample is produced by a designed sequential deposition of the constituent inks, and results in compositions gradients with ≈5000 points/sample that cover about 15%–25% of the phase space. These effective ternary libraries are then colocally imaged by a combination of photovoltaic techniques (laser and white light photocurrent maps) and spectroscopic techniques (Raman, photoluminescence, absorption). The generality of the methodology is demonstrated by investigating three ternary systems, namely PBDB‐T:ITIC:PC₇₀BM, PTB7‐Th:ITIC:PC₇₀BM, and P3HT:O‐IDFBR:O‐IDTBR. Complex performance‐structure landscapes through the ternary diagram as well as the emergence of several performance maxima are discovered.     

Exploring the accuracy of amplicon‐based internal transcribed spacer markers for a fungal community

With the continual improvement in high‐throughput sequencing technology and constant updates to fungal reference databases, the use of amplicon‐based DNA markers as a tool to reveal fungal diversity and composition in various ecosystems has become feasible. However, both primer selection and the experimental procedure require meticulous verification. Here, we computationally and experimentally evaluated the accuracy and specificity of three widely used or newly designed internal transcribed spacer (ITS) primer sets (ITS1F/ITS2, gITS7/ITS4 and 5.8S‐Fun/ITS4‐Fun). In silico evaluation revealed that primer coverage varied at different taxonomic levels due to differences in degeneracy and the location of primer sets. Using even and staggered mock community standards, we identified different proportions of chimeric and mismatch reads generated by different primer sets, as well as great variation in species abundances, suggesting that primer selection would affect the results of amplicon‐based metabarcoding studies. Choosing proofreading and high‐fidelity polymerase (KAPA HiFi) could significantly reduce the percentage of chimeric and mismatch sequences, further reducing inflation of operational taxonomic units. Moreover, for two types of environmental fungal communities, plant endophytic and soil fungi, it was demonstrated that the three primer sets could not reach a consensus on fungal community composition or diversity, and that primer selection, not experimental treatment, determines observed soil fungal community diversity and composition. Future DNA marker surveys should pay greater attention to potential primer effects and improve the experimental scheme to increase credibility and accuracy.     

Deep‐branching Novel Lineages and High Diversity of Haptophytes in the Skagerrak (Norway) Uncovered by 454 Pyrosequencing

Microalgae in the division Haptophyta may be difficult to identify to species by microscopy because they are small and fragile. Here, we used high‐throughput sequencing to explore the diversity of haptophytes in outer Oslofjorden, Skagerrak, and supplemented this with electron microscopy. Nano‐ and picoplanktonic subsurface samples were collected monthly for 2 yr, and the haptophytes were targeted by amplification of RNA/cDNA with Haptophyta‐specific 18S ribosomal DNA V4 primers. Pyrosequencing revealed higher species richness of haptophytes than previously observed in the Skagerrak by microscopy. From ca. 400,000 reads we obtained 156 haptophyte operational taxonomic units (OTUs) after rigorous filtering and 99.5% clustering. The majority (84%) of the OTUs matched environmental sequences not linked to a morphological species, most of which were affiliated with the order Prymnesiales. Phylogenetic analyses including Oslofjorden OTUs and available cultured and environmental haptophyte sequences showed that several of the OTUs matched sequences forming deep‐branching lineages, potentially representing novel haptophyte classes. Pyrosequencing also retrieved cultured species not previously reported by microscopy in the Skagerrak. Electron microscopy revealed species not yet genetically characterised and some potentially novel taxa. This study contributes to linking genotype to phenotype within this ubiquitous and ecologically important protist group, and reveals great, unknown diversity.     

Evaluation of the effects of various culture conditions on Cr(VI) reduction by Shewanella oneidensis MR-1 in a novel high-throughput mini-bioreactor

The growth and Cr(VI) reduction by Shewanella oneidensis MR-1 was examined using a mini-bioreactor system that independently monitors and controls pH, dissolved oxygen (DO), and temperature for each of its 24, 10-mL reactors. Independent monitoring and control of each reactor in the cassette allows the exploration of a matrix of environmental conditions known to influence S. oneidensis chromium reduction. S. oneidensis MR-1 grew in minimal medium without amino acid or vitamin supplementation under aerobic conditions but required serine and glycine supplementation under anaerobic conditions. Growth was inhibited by DO concentrations >80%. Lactate transformation to acetate was enhanced by low concentration of DO during the logarithmic growth phase. Between 11 and 35 degrees C, the growth rate obeyed the Arrhenius reaction rate-temperature relationship, with a maximum growth rate occurring at 35 degrees C. S. oneidensis MR-1 was able to grow over a wide range of pH (6-9). At neutral pH and temperatures ranging from 30 to 35 degrees C, S. oneidensis MR-1 reduced 100 microM Cr(VI) to Cr(III) within 20 min in the exponential growth phase, and the growth rate was not affected by the addition of chromate; it reduced chromate even faster at temperatures between 35 and 39 degrees C. At low temperatures (<25 degrees C), acidic (pH < 6.5), or alkaline (pH > 8.5) conditions, 100 microM Cr(VI) strongly inhibited growth and chromate reduction. The mini-bioreactor system enabled the rapid determination of these parameters reproducibly and easily by performing very few experiments. Besides its use for examining parameters of interest to environmental remediation, the device will also allow one to quickly assess parameters for optimal production of recombinant proteins or secondary metabolites.     

Improving the Performance and Stability of Inverted Planar Flexible Perovskite Solar Cells Employing a Novel NDI‐Based Polymer as the Electron Transport Layer

A new naphthalene diimide (NDI)‐based polymer with strong electron withdrawing dicyanothiophene (P(NDI2DT‐TTCN)) is developed as the electron transport layer (ETL) in place of the fullerene‐based ETL in inverted perovskite solar cells (Pero‐SCs). A combination of characterization techniques, including atomic force microscopy, scanning electron microscopy, grazing‐incidence wide‐angle X‐ray scattering, near‐edge X‐ray absorption fine‐structure spectroscopy, space‐charge‐limited current, electrochemical impedance spectroscopy, photoluminescence (PL), and time‐resolved PL decay, is used to demonstrate the interface phenomena between perovskite and P(NDI2DT‐TTCN) or [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). It is found that P(NDI2DT‐TTCN) not only improves the electron extraction ability but also prevents ambient condition interference by forming a hydrophobic ETL surface. In addition, P(NDI2DT‐TTCN) has excellent mechanical stability compared to PCBM in flexible Pero‐SCs. With these improved functionalities, the performance of devices based on P(NDI2DT‐TTCN) significantly outperform those based on PCBM from 14.3 to 17.0%, which is the highest photovoltaic performance with negligible hysteresis in the field of polymeric ETLs.