Atomic Fe‐Doped MOF‐Derived Carbon Polyhedrons with High Active‐Center Density and Ultra‐High Performance toward PEM Fuel Cells

A metalorganic gaseous doping approach for constructing nitrogen‐doped carbon polyhedron catalysts embedded with single Fe atoms is reported. The resulting catalysts are characterized using scanning transmission electron microscopy, X‐ray photoelectron spectroscopy, and X‐ray absorption spectroscopy; for the optimal sample, calculated densities of Fe–N_x sites and active N sites reach 1.75812 × 10¹³ and 1.93693 × 10¹⁴ sites cm^‐2, respectively. Its oxygen reduction reaction half‐wave potential (0.864 V) is 50 mV higher than that of 20 wt% Pt/C catalyst in an alkaline medium and comparable to the latter (0.78 V vs 0.84 V) in an acidic medium, along with outstanding durability. More importantly, when used as a hydrogen–oxygen polymer electrolyte membrane fuel cell (PEMFC) cathode catalyst with a catalyst loading as low as 1 mg cm^‐2 (compared with a conventional loading of 4 mg cm^‐2), it exhibits a current density of 1100 mA cm^‐2 at 0.6 V and 637 mA cm^‐2 at 0.7 V, with a power density of 775 mW cm^‐2, or 0.775 kW g^–1 of catalyst. In a hydrogen–air PEMFC, current density reaches 650 mA cm^‐2 at 0.6 V and 350 mA cm^‐2 at 0.7 V, and the maximum power density is 463 mW cm^‐2, which makes it a promising candidate for cathode catalyst toward high‐performance PEMFCs.     

Active‐Site Imprinting: Preparation of Fe–N–C Catalysts from Zinc Ion–Templated Ionothermal Nitrogen‐Doped Carbons

Atomically dispersed Fe–N–C catalysts are considered the most promising precious‐metal‐free alternative to state‐of‐the‐art Pt‐based oxygen reduction electrocatalysts for proton‐exchange membrane fuel cells. The exceptional progress in the field of research in the last ≈30 years is currently limited by the moderate active site density that can be obtained. Behind this stands the dilemma of metastability of the desired FeN₄ sites at the high temperatures that are believed to be a requirement for their formation. It is herein shown that Zn²⁺ ions can be utilized in the novel concept of active‐site imprinting based on a pyrolytic template ion reaction throughout the formation of nitrogen‐doped carbons. As obtained atomically dispersed Zn–N–Cs comprising ZnN₄ sites as well as metal‐free N₄ sites can be utilized for the coordination of Fe²⁺ and Fe³⁺ ions to form atomically dispersed Fe–N–C with Fe loadings as high as 3.12 wt%. The Fe–N–Cs are active electocatalysts for the oxygen reduction reaction in acidic media with an onset potential of E₀ = 0.85 V versus RHE in 0.1 m HClO₄. Identical location atomic resolution transmission electron microscopy imaging, as well as in situ electrochemical flow cell coupled to inductively coupled plasma mass spectrometry measurements, is employed to directly prove the concept of the active‐site imprinting approach.     

Fe?N4 Sites Embedded into Carbon Nanofiber Integrated with Electrochemically Exfoliated Graphene for Oxygen Evolution in Acidic Medium

Development of inexpensive and efficient oxygen evolution reaction (OER) catalysts in acidic environment is very challenging, but it is important for practical proton exchange membrane water electrolyzers. A molecular iron–nitrogen coordinated carbon nanofiber is developed, which is supported on an electrochemically exfoliated graphene (FeN₄/NF/EG) electrocatalyst through carbonizing the precursor composed of iron ions absorbed on polyaniline‐electrodeposited EG. Benefitting from the unique 3D structure, the FeN₄/NF/EG hybrid exhibits a low overpotential of ≈294 mV at 10 mA cm^?2 for the OER in acidic electrolyte, which is much lower than that of commercial Ir/C catalysts (320 mV) as well as all previously reported acid transitional metal‐derived OER electrocatalysts. X‐ray absorption spectroscopy coupled with a designed poisoning experiment reveals that the molecular Fe? N₄ species are identified as active centers for the OER in acid. The first‐principles‐based calculations verify that the Fe? N₄–doped carbon structure is capable of reducing the potential barriers and boosting the electrocatalytic OER activity in acid.     

FeN4 Sites Embedded into Carbon Nanofiber Integrated with Electrochemically Exfoliated Graphene for Oxygen Evolution in Acidic Medium

Development of inexpensive and efficient oxygen evolution reaction (OER) catalysts in acidic environment is very challenging, but it is important for practical proton exchange membrane water electrolyzers. A molecular iron–nitrogen coordinated carbon nanofiber is developed, which is supported on an electrochemically exfoliated graphene (FeN₄/NF/EG) electrocatalyst through carbonizing the precursor composed of iron ions absorbed on polyaniline‐electrodeposited EG. Benefitting from the unique 3D structure, the FeN₄/NF/EG hybrid exhibits a low overpotential of ≈294 mV at 10 mA cm^?2 for the OER in acidic electrolyte, which is much lower than that of commercial Ir/C catalysts (320 mV) as well as all previously reported acid transitional metal‐derived OER electrocatalysts. X‐ray absorption spectroscopy coupled with a designed poisoning experiment reveals that the molecular Fe?N₄ species are identified as active centers for the OER in acid. The first‐principles‐based calculations verify that the Fe?N₄–doped carbon structure is capable of reducing the potential barriers and boosting the electrocatalytic OER activity in acid.     

Atomically Dispersed Fe‐Nx/C Electrocatalyst Boosts Oxygen Catalysis via a New Metal‐Organic Polymer Supramolecule Strategy

The development of high‐performance oxygen reduction reaction (ORR) catalysts derived from non‐Pt group metals (non‐PGMs) is urgent for the wide applications of proton exchange membrane fuel cells (PEMFCs). In this work, a facile and cost‐efficient supramolecular route is developed for making non‐PGM ORR catalyst with atomically dispersed Fe‐N_x/C sites through pyrolyzing the metal‐organic polymer coordinative hydrogel formed between Fe³⁺ and α‐L‐guluronate blocks of sodium alginate (SA). High‐angle annular dark field scanning transmission electron microscopy (HAADF‐STEM) and X‐ray absorption spectroscopy (XAS) verify that Fe atoms achieve atomic‐level dispersion on the obtained SA‐Fe‐N nanosheets and a possible fourfold coordination with N atoms. The best‐performing SA‐Fe‐N catalyst exhibits excellent ORR activity with half‐wave potential (E_1/2) of 0.812 and 0.910 V versus the reversible hydrogen electrode (RHE) in 0.5 m H₂SO₄ and 0.1 m KOH, respectively, along with respectable durability. Such performance surpasses that of most reported non‐PGM ORR catalysts. Density functional theory calculations suggest that the relieved passivation effect of OH* on Fe‐N₄/C structure leads to its superior ORR activity to Pt/C in alkaline solution. The work demonstrates a novel strategy for developing high‐performance non‐PGM ORR electrocatalysts with atomically dispersed and stable M‐N_x coordination sites in both acidic and alkaline media.     

Bimetallic Zeolitic Imidazolite Framework Derived Carbon Nanotubes Embedded with Co Nanoparticles for Efficient Bifunctional Oxygen Electrocatalyst

Bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with high activities and low‐cost are of prime importance and challenging in the development of fuel cells and rechargeable metal–air batteries. This study reports a porous carbon nanomaterial loaded with cobalt nanoparticles (Co@NC‐x/y) derived from pyrolysis of a Co/Zn bimetallic zeolitic imidazolite framework, which exhibits incredibly high activity as bifunctional oxygen catalysts. For instance, the optimal catalyst of Co@NC‐3/1 has the interconnected framework structure between porous carbon and embedded carbon nanotubes, which shows the superb ORR activity with onset potential of ≈1.15 V and half‐wave potential of ≈0.93 V. Moreover, it presents high OER activity that can be further enhanced to over commercial RuO₂ by P‐doped with overpotentials of 1.57 V versus reversible hydrogen electrode at 10 mA cm^?2 and long‐term stability for 2000 circles and a Tafel slope of 85 mV dec^?1. Significantly, the nanomaterial demonstrates better catalytic performance and durability than Pt/C for ORR and commercial RuO₂ and IrO₂ for OER. These findings suggest the importance of a synergistic effect of graphitic carbon, nanotubes, exposed Co–N_x active sites, and interconnected framework structure of various carbons for bifunctional oxygen electrocatalysts.     

Degradation Mechanism and Enhancing Strategies of Oxygen Reduction Reaction Catalyzed by Carbon-Based Metal Free Catalysts in Acidic Solution

Carbon-based metal free catalysts (CMFCs) are far away from commercial availability mainly attributed to their poor oxygen reduction reaction (ORR) performance in acidic environment with the causes remaining obscure. By investigating the heteroatoms (N, B, P, S, Se, and Te)-doped reduced graphene oxides, the degradation mechanism of acidic ORR performance of CMFCs is found to be correlated with the oxygen-baring defects in the carbon sp² lattice, which exhibit overpotentials as low as 0.44 V but weak trapping capabilities for oxygen molecules. These findings not only revise the previously reported strategy of modeling the active sites in the basal plane of CMFCs but also highlight the connections between those active sites and the triple-coordinated VIA group elements (XC₃). Further calculations demonstrate that the XC₃ dimer can efficiently enhance the acidic ORR performance and the 2D trigonal carbon-chalcogenides C₆X (X = S, Se, and Te) are accordingly designed toward acidic ORR, which contain homogeneously distributed basal plane active sites and exhibit low overpotentials but strong trapping capabilities for oxygen molecules. This work will help to cease the debates on the active sites in CMFCs for ORR in both acidic and alkaline solutions and to open a new avenue to design CMFCs independent on doping strategy.     

Dual‐Functional N Dopants in Edges and Basal Plane of MoS2 Nanosheets Toward Efficient and Durable Hydrogen Evolution

Herein, the authors explicitly reveal the dual‐functions of N dopants in molybdenum disulfide (MoS₂) catalyst through a combined experimental and first‐principles approach. The authors achieve an economical, ecofriendly, and most efficient MoS₂‐based hydrogen evolution reaction (HER) catalyst of N‐doped MoS₂ nanosheets, exhibiting an onset overpotential of 35 mV, an overpotential of 121 mV at 100 mA cm^?2 and a Tafel slope of 41 mV dec^?1. The dual‐functions of N dopants are (1) activating the HER catalytic activity of MoS₂ S‐edge and (2) enhancing the conductivity of MoS₂ basal plane to promote rapid charge transfer. Comprehensive electrochemical measurements prove that both the amount of active HER sites and the conductivity of N‐doped MoS₂ increase as a result of doping N. Systematic first‐principles calculations identify the active HER sites in N‐doped MoS₂ edges and also illustrate the conducting charges spreading over N‐doped basal plane induced by strong Mo 3d –S 2p –N 2p hybridizations at Fermi level. The experimental and theoretical research on the efficient HER catalysis of N‐doped MoS₂ nanosheets possesses great potential for future sustainable hydrogen production via water electrolysis and will stimulate further development on nonmetal‐doped MoS₂ systems to bring about novel high‐performance HER catalysts.     

Cross Talk between Transition Metal Cathode and Li Metal Anode: Unraveling Its Influence on the Deposition/Dissolution Behavior and Morphology of Lithium

Lithium metal batteries (LMBs) combining a Li metal anode with a transition metal (TM) cathode can achieve higher practical energy densities (Wh L^?1) than Li/S or Li/O₂ cells. Research for improving the electrochemical behavior of the Li metal anode by, for example, modifying the liquid electrolyte is often conducted in symmetrical Li/Li or Li/Cu cells. This study now demonstrates the influence of the TM cathode on the Li metal anode, thus full cell behavior is analyzed in a way not considered so far in research with LMBs. Therefore, the deposition/dissolution behavior of Li metal and the resulting morphology is investigated with three different cathode materials (LiNi_0.5Mn_1.5O₄, LiNi_0.6Mn_0.2Co_0.2O₂, and LiFePO₄) by post mortem analysis with a scanning electron microscope. The observed large differences of the Li metal morphology are ascribed to the dissolution and crossover of TMs found deposited on Li metal and in the electrolyte by X‐ray photoelectron spectroscopy, energy‐dispersive X‐ray spectroscopy, and total reflection X‐ray fluorescence analysis. To support this correlation, the TM dissolution is simulated by adding Mn salt to the electrolyte. This study offers new insights into the cross talk between the Li metal anodes and TM cathodes, which is essential, when investigating Li metal electrodes for LMB full cells.     

Surface Engineering of 3D Gas Diffusion Electrodes for High‐Performance H2 Production with Nonprecious Metal Catalysts

In this work, a methodology is demonstrated to engineer gas diffusion electrodes for nonprecious metal catalysts. Highly active transition metal phosphides are prepared on carbon‐based gas diffusion electrodes with low catalyst loadings by modifying the O/C ratio at the surface of the electrode. These nonprecious metal catalysts yield extraordinary performance as measured by low overpotentials (51 mV at ?10 mA cm^?2), unprecedented mass activities (>800 A g^?1 at 100 mV overpotential), high turnover frequencies (6.96 H₂ s^?1 at 100 mV overpotential), and high durability for a precious metal‐free catalyst in acidic media. It is found that a high O/C ratio induces a more hydrophilic surface directly impacting the morphology of the CoP catalyst. The improved hydrophilicity, stemming from introduced oxyl groups on the carbon electrode, creates an electrode surface that yields a well‐distributed growth of cobalt electrodeposits and thus a well‐dispersed catalyst layer with high surface area upon phosphidation. This report demonstrates the high‐performance achievable by CoP at low loadings which facilitates further cost reduction, an important part of enabling the large‐scale commercialization of non‐platinum group metal catalysts. The fabrication strategies described herein offer a pathway to lower catalyst loading while achieving high efficiency and promising stability on a 3D electrode.     

Uniform Lithium Deposition Assisted by Single‐Atom Doping toward High‐Performance Lithium Metal Anodes

For a long time lithium (Li) metal has been considered one of the most promising anodes for next‐generation rechargeable batteries. Despite decades of concentrated research, its practical application is still hindered by dendritic Li deposition and infinite volume change of Li metal anodes. Here, atomically dispersed metals doped graphene is synthesized to regulate Li metal nucleation and guide Li metal deposition. The single‐atom (SA) metals, supported on the nitrogen‐doped graphene can not only increase the Li adsorption energy of the localized area around the metal atomic sites with a moderate adsorption energy gradient but also improve the atomic structural stability of the overall materials by constructing a coordination mode of M‐N_x‐C (M, N, and C denoted as metal, nitrogen, and carbon atoms, respectively). As a result, the as‐obtained electrode exhibits an ultralow voltage hysteresis of 19 mV, a high average Coulombic efficiency of 98.45% over 250 cycles, and a stable Li plating/stripping performance even at a high current density of 4.0 mA cm^?2. This work demonstrates the application of SA metal doping in the rational design of Li metal anodes and provides a new concept for further development of Li metal batteries.     

Enhanced Cathodic Oxygen Reduction and Power Production of Microbial Fuel Cell Based on Noble‐Metal‐Free Electrocatalyst Derived from Metal‐Organic Frameworks

Microbial fuel cell (MFC) can generate electricity from organic substances based on anodic electrochemically active microorganisms and cathodic oxygen reduction reaction (ORR), thus exhibiting promising potential for harvesting electric energy from organic wastewater. The ORR performance is crucial to both power production efficiency and overall cost of MFC. A new type of metal‐organic‐framework‐derived electrocatalysts containing cobalt and nitrogen‐doped carbon (CoNC) is developed, which is effective to enhance activity, selectivity, and stability toward four‐electron ORR in pH‐neutral electrolyte. When glucose is used as the substrate, the maximum power density of 1665 mW m^?2 is achieved for the optimized CoNC pyrolyzed at 900 °C, which is 39.8% higher than that of 1191 mW m^?2 for commercial Pt/C catalyst in the single‐chamber MFC. The improved performance of CoNC catalyst can be attributed to large surface area, microporous nature, and the involvement of nitrogen‐coordinated cobalt species. These properties enable the efficient ORR by increasing the active sites and enhancing mass transfer of oxygen and protons at “water‐flooding” three‐phase boundary where ORR occurs. This work provides a proof‐of‐concept demonstration of a noble‐metal‐free high‐efficiency and cost‐effective ORR electrocatalyst for effective recovery of electricity from biomass materials and organic wastewater in MFC.     

Fast and Stable Proton Conduction in Heavily Scandium‐Doped Polycrystalline Barium Zirconate at Intermediate Temperatures

The environmental benefits of fuel cells and electrolyzers have become increasingly recognized in recent years. Fuel cells and electrolyzers that can operate at intermediate temperatures (300–450 °C) require, in principle, neither the precious metal catalysts that are typically used in polymer‐electrolyte‐membrane systems nor the costly heat‐resistant alloys used in balance‐of‐plant components of high‐temperature solid oxide electrochemical cells. These devices require an electrolyte with high ionic conductivity, typically more than 0.01 S cm^?1, and high chemical stability. To date, however, high ionic conductivities have been found in chemically unstable materials such as CsH₂PO₄, In‐doped SnP₂O₇, BaH₂, and LaH_3?2xO_x. Here, fast and stable proton conduction in 60‐at% Sc‐doped barium zirconate polycrystal, with a total conductivity of 0.01 S cm^?1 at 396 °C for 200 h is demonstrated. Heavy doping of Sc in barium zirconate simultaneously enhances the proton concentration, bulk proton diffusivity, specific grain boundary conductivity, and grain growth. An accelerated stability test under a highly concentrated and humidified CO₂ stream using in situ X‐ray diffraction shows that the perovskite phase is stable over 240 h at 400 °C under 0.98 atm of CO₂. These results show great promises as an electrolyte in solid‐state electrochemical devices operated at intermediate temperatures.     

Reducing Capacity and Voltage Decay of Co‐Free Li1.2Ni0.2Mn0.6O2 as Positive Electrode Material for Lithium Batteries Employing an Ionic Liquid‐Based Electrolyte

Lithium‐rich layered oxides (LRLOs) exhibit specific capacities above 250 mAh g^?1, i.e., higher than any of the commercially employed lithium‐ion‐positive electrode materials. Such high capacities result in high specific energies, meeting the tough requirements for electric vehicle applications. However, LRLOs generally suffer from severe capacity and voltage fading, originating from undesired structural transformations during cycling. Herein, the eco‐friendly, cobalt‐free Li_1.2Ni_0.2Mn_0.6O₂ (LRNM), offering a specific energy above 800 Wh kg^?1 at 0.1 C, is investigated in combination with a lithium metal anode and a room temperature ionic liquid‐based electrolyte, i.e., lithium bis(trifluoromethanesulfonyl)imide and N‐butyl‐N‐methylpyrrolidinium bis(fluorosulfonyl)imide. As evidenced by electrochemical performance and high‐resolution transmission electron microscopy, X‐ray photoelectron spectroscopy, and online differential electrochemical mass spectrometry characterization, this electrolyte is capable of suppressing the structural transformation of the positive electrode material, resulting in enhanced cycling stability compared to conventional carbonate‐based electrolytes. Practically, the capacity and voltage fading are significantly limited to only 19% and 3% (i.e., lower than 0.2 mV per cycle), respectively, after 500 cycles. Finally, the beneficial effect of the ionic liquid‐based electrolyte is validated in lithium‐ion cells employing LRNM and Li₄Ti₅O₁₂. These cells achieve a promising capacity retention of 80% after 500 cycles at 1 C.     

Surface‐Guided Formation of Amorphous Mixed‐Metal Oxyhydroxides on Ultrathin MnO2 Nanosheet Arrays for Efficient Electrocatalytic Oxygen Evolution

Earth‐abundant amorphous nanomaterials with rich structural defects are promising alternative catalysts to noble metals for an efficient electrochemical oxygen evolution reaction; however, their inferior electrical conductivity and poor morphological control during synthesis hamper the full realization of their potency in electrocatalysis. Herein, a rapid surface‐guided synthetic approach is proposed to introduce amorphous and mixed‐metal oxyhydroxide overlayers on ultrathin Ni‐doped MnO₂ (Ni? MnO₂) nanosheet arrays via a galvanic replacement mechanism. This method results in a monolithic 3D porous catalyst with a small overpotential of only 232 mV to achieve a current density of 10 mA cm^?2 in 1 m KOH, which is much lower than the corresponding value of 307 mV for the Ni? MnO₂ reference sample. Detailed structural and electrochemical characterization reveal that the unique Ni? MnO₂ ultrathin nanosheet arrays do not only provide a large surface area to guide the formation of active amorphous catalyst layers but also ensure the effective charge transport owing to their high electron conductivity, collectively contributing to the greatly improved catalyst activity. It is envisioned that this highly operable surface‐guide synthetic strategy may open up new avenues for the design and fabrication of novel 3D nanoarchitectures integrated with functional amorphous materials for broadened ranges of applications.     

Manganese Oxide Modified Nickel Catalysts for Photothermal CO Hydrogenation to Light Olefins

Ni‐based catalysts are traditionally considered unsuitable for the Fischer–Tropsch syntheses of olefins, due to the very strong hydrogenation ability of metallic Ni. Herein, this paradigm is challenged. A series of MnO supports nickel catalysts (denoted herein as Ni‐x) are fabricated by H₂ reduction of a nickel‐manganese mixed metal oxide at temperatures (x) ranging from 250 to 600 °C. The Ni‐500 catalyst displays unprecedented performance for photothermal CO hydrogenation to olefins, with an olefin selectivity of 33.0% under ultraviolet–visible irradiation. High‐resolution transmission electron microscopy, X‐ray absorption spectroscopy (XAS), and X‐ray diffraction analyses reveal that the Ni‐x catalysts contain metallic Ni nanoparticles supported by MnO. X‐ray photoelectron spectroscopy and XAS establish that electron transfer from MnO to the Ni⁰ nanoparticles is responsible for modifying the electronic structure of nickel (creating Ni^δ? states), thereby shifting the CO hydrogenation selectivity toward light olefins. Further, density functional theory calculations show that this electron transfer lowers the adsorption energies of olefins on Ni surfaces, thus minimizing the undesirable deep hydrogenation reactions to higher alkanes. This study conclusively demonstrates that MnO‐modified Ni‐based catalyst systems can be highly selective for CO hydrogenation to light olefins.     

N‐butylamine functionalized graphene oxide for detection of iron(III) by photoluminescence quenching

An N‐butylamine functionalized graphene oxide nanolayer was synthesized and characterized by ultraviolet (UV)–visible spectrometry, Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and transmission electron microscopy. Detection of iron(III) based on photoluminescence spectroscopy was investigated. The N‐butylamine functionalized graphene oxide was shown to specifically interact with iron (III), compared with other cationic trace elements including potassium (I), sodium (I), calcium (II), chromium (III), zinc (II), cobalt (II), copper (II), magnesium (II), manganese (II), and molybdenum (VI). The quenching effect of iron (III) on the luminescence emission of N‐butylamine functionalized graphene oxide layer was used to detect iron (III). The limit of detection (2.8 × 10^?6 M) and limit of quantitation (2.9 × 10^?5 M) were obtained under optimal conditions. Copyright © 2015 John Wiley & Sons, Ltd.     

Highly Stable Carbon‐Free Ag/Co3O4‐Cathodes for Lithium‐Air Batteries: Electrochemical and Structural Investigations

Lithium‐air batteries with an aqueous alkaline electrolyte promise a much higher practical energy density and capacity than conventional lithium‐ion batteries. However, high cathode overpotentials are some of the main problems during cycling. In our previous work, a catalyst combination of Ag and Co₃O₄ is found that reduces overpotential significantly, and is highly active and also long‐term stable. In the present investigations, X‐ray diffraction and X‐ray photoelectron spectroscopy are applied to study the structure and composition of the cathode material during oxygen reduction reaction and oxygen evolution reaction. Changes of the oxidation states during cycling are responsible for an enhanced oxygen evolution reaction current density but also for losses due to a lower electronic conductivity of the electrodes. The presence and formation of a mixed oxidation state for silver oxide (Ag^IAg^IIIO₂) at high potentials is identified. In contradiction to literature, time dependent X‐ray diffraction measurements evidence that this phase is not stable under dry conditions and progressively decays to Ag₂O. Electrode mappings show a highly homogeneous oxidation of the electrodes during cycling and quantitative analysis of the observed phases is carried out by Rietveld analysis. Long‐term material behavior completes the investigations.     

Active Edge Sites Engineering in Nickel Cobalt Selenide Solid Solutions for Highly Efficient Hydrogen Evolution

An effective multifaceted strategy is demonstrated to increase active edge site concentration in Ni_0.33Co_0.67Se₂ solid solutions prepared by in situ selenization process of nickel cobalt precursor. The simultaneous control of surface, phase, and morphology result in as‐prepared ternary solid solution with extremely high electrochemically active surface area (C _dl = 197 mF cm^?2), suggesting significant exposure of active sites in this ternary compound. Coupled with metallic‐like electrical conductivity and lower free energy for atomic hydrogen adsorption in Ni_0.33Co_0.67Se₂, identified by temperature‐dependent conductivities and density functional theory calculations, the authors have achieved unprecedented fast hydrogen evolution kinetics, approaching that of Pt. Specifically, the Ni_0.33Co_0.67Se₂ solid solutions show a low overpotential of 65 mV at ?10 mV cm^?2, with onset potential of mere 18 mV, an impressive small Tafel slope of 35 mV dec^?1, and a large exchange current density of 184 µA cm^?2 in acidic electrolyte. Further, it is shown that the as‐prepared Ni_0.33Co_0.67Se₂ solid solution not only works very well in acidic electrolyte but also delivers exceptional hydrogen evolution reaction (HER) performance in alkaline media. The outstanding HER performance makes this solid solution a promising candidate for mass hydrogen production.