Efficient Perovskite Photovoltaic‐Thermoelectric Hybrid Device

An efficient perovskite photovoltaic‐thermoelectric hybrid device is demonstrated by integrating the hole‐conductor‐free perovskite solar cell based on TiO₂/ZrO₂/carbon structure and the thermoelectric generator. The whole solar spectrum of AM 1.5 G is fully utilized with the ≈1.55 eV band gap perovskite (5‐AVA)_x(MA)_1?xPbI₃ absorbing the visible light and the carbon back contact absorbing the infrared light. The added thermoelectric generator improves the device performance by converting the thermal energy into electricity via the Seebeck effect. An optimized hybrid device is obtained with a maximum point power output of 20.3% and open‐circuit voltage of 1.29 V under the irradiation of 100 mW cm^?2.     

p‐Type CuI Islands on TiO2 Electron Transport Layer for a Highly Efficient Planar‐Perovskite Solar Cell with Negligible Hysteresis

Compact TiO₂ is widely used as an electron transport material in planar‐perovskite solar cells. However, TiO₂‐based planar‐perovskite solar cells exhibit low efficiencies due to intrinsic problems such as the unsuitable conduction band energy and low electron extraction ability of TiO₂. Herein, the planar TiO₂ electron transport layer (ETL) of perovskite solar cells is modified with ionic salt CuI via a simple one‐step spin‐coating process. The p‐type nature of the CuI islands on the TiO₂ surface leads to modification of the TiO₂ band alignment, resulting in barrier‐free contacts and increased open‐circuit voltage. It is found that the polarity of the CuI‐modified TiO₂ surface can pull electrons to the interface between the perovskite and the TiO₂, which improves electron extraction and reduces nonradiative recombination. The CuI solution concentration is varied to control the electron extraction of the modified TiO₂ ETL, and the optimized device shows a high efficiency of 19.0%. In addition, the optimized device shows negligible hysteresis, which is believed to be due to the removal of trap sites and effective electron extraction by CuI‐modified TiO₂. These results demonstrate the hitherto unknown effect of p‐type ionic salts on electron transport material.     

Synthesis and Characterization of Acceptor‐Substituted Oligothiophenes for Solar Cell Applications

We report the synthesis of novel acceptor‐substituted oligothiophenes and their application in m‐i‐p type planar heterojunction solar cells. Optical absorption spectra and electrochemical properties of the dyes are investigated. The determined energy levels of these dyes suggest that they should be ideal for use in heterojunction solar cells. We further investigate the influence of acceptor groups on the device performance by introducing 1,1‐dicyano‐2‐methyl‐vinyl and 1,1‐dicyano‐2‐phenyl‐vinyl groups, respectively, as acceptor units. Photovoltaic devices incorporating these dyes show an open circuit voltage of up to 0.96 V and power conversion efficiencies in the range of 1.5–3.0% under full sun illumination (simulated AM 1.5G sunlight, 100 mW cm^?2).     

Mesoporous TiO2 Beads Offer Improved Mass Transport for Cobalt‐Based Redox Couples Leading to High Efficiency Dye‐Sensitized Solar Cells

Overcoming ionic diffusion limitations is essential for the development of high‐efficiency dye‐sensitized solar cells based on cobalt redox mediators. Here, improved mass transport is reported for photoanodes composed of mesoporous TiO₂ beads of varying pore sizes and porosities in combination with the high extinction YD2‐o‐C8 porphyrin dye. Compared to a photoanode made of 20 nm‐sized TiO₂ particles, electrolyte diffusion through these films is greatly improved due to the large interstitial pores between the TiO₂ beads, resulting in up to 70% increase in diffusion‐limited current. Simultaneously, transient photocurrent measurements reveal no mass transport limitations for films of up to 10 μm thickness. In contrast, standard photoanodes made of 20 nm‐sized TiO₂ particles show non‐linear behavior in photocurrent under 1 sun illumination for a film thickness as low as 7 μm. By including a transparent thin mesoporous TiO₂ underlayer in order to reduce optical losses at the fluorine‐doped tin oxide (FTO)‐TiO₂ interface, an efficiency of 11.4% under AM1.5G 1 sun illumination is achieved. The combination of high surface area, strong scattering behavior, and high porosity makes these mesoporous TiO₂ beads particularly suitable for dye‐sensitized solar cells using bulky redox couples and/or viscous electrolytes.     

Efficient Indium‐Doped TiOx Electron Transport Layers for High‐Performance Perovskite Solar Cells and Perovskite‐Silicon Tandems

In addition to a good perovskite light absorbing layer, the hole and electron transport layers play a crucial role in achieving high‐efficiency perovskite solar cells. Here, a simple, one‐step, solution‐based method is introduced for fabricating high quality indium‐doped titanium oxide electron transport layers. It is shown that indium‐doping improves both the conductivity of the transport layer and the band alignment at the ETL/perovskite interface compared to pure TiO₂, boosting the fill‐factor and voltage of perovskite cells. Using the optimized transport layers, a high steady‐state efficiency of 17.9% for CH₃NH₃PbI₃‐based cells and 19.3% for Cs_0.05(MA_0.17FA_0.83)_0.95Pb(I_0.83Br_0.17)₃‐based cells is demonstrated, corresponding to absolute efficiency gains of 4.4% and 1.2% respectively compared to TiO₂‐based control cells. In addition, a steady‐state efficiency of 16.6% for a semi‐transparent cell is reported and it is used to achieve a four‐terminal perovskite‐silicon tandem cell with a steady‐state efficiency of 24.5%.     

MoS2‐Based All‐Purpose Fibrous Electrode and Self‐Powering Energy Fiber for Efficient Energy Harvesting and Storage

Here an all‐purpose fibrous electrode based on MoS₂ is demonstrated, which can be employed for versatile energy harvesting and storage applications. In this coaxial electrode, ultrathin MoS₂ nanofilms are grown on TiO₂ nanoparticles coated carbon fiber. The high electrochemical activity of MoS₂ and good conductivity of carbon fiber synergistically lead to the remarkable performances of this novel composite electrode in fibrous dye‐sensitized solar cells (showing a record‐breaking conversion efficiency of 9.5%) and high‐capacity fibrous supercapacitors. Furthermore, a self‐powering energy fiber is fabricated by combining a fibrous dye‐sensitized solar cell and a fibrous supercapacitor into a single device, showing very fast charging capability (charging in 7 s under AM1.5G solar illumination) and an overall photochemical‐electricity energy conversion efficiency as high as 1.8%. In addition, this wire‐shaped electrode can also be used for fibrous Li‐ion batteries and electrocatalytic hydrogen evolution reactions. These applications indicate that the MoS₂‐based all‐purpose fibrous electrode has great potential for the construction of high‐performance flexible and wearable energy devices.     

Control over Self‐Doping in High Band Gap Perovskite Films

It is reported how differences in the composition of high bandgap Pb bromide‐based perovskites affect their carrier diffusion length and junction type. Pb‐based, APbX₃, halide perovskite (HaP) films and devices are studied, where A can be a mixture of formamidinium, methylammonium (MA), and Cs, and X a mixture of Br and Cl, using a combination of dark‐ and photoconductivity and steady‐state photocarrier grating. The results show the cation and anion compositions affect both majority and minority carrier diffusion lengths. In particular, using electron beam‐induced current measurements, FTO\dTiO₂mp‐TiO₂HaP\PTAA (poly‐triarylamine)\Au devices are studied. The results enable identifying junction and built‐in voltage formation and track position and size of the space charge region width with changes in the HaP composition. As far as it is known, it is found for the first time that a mixed‐cation HaP forms a junction that has characteristics of a p‐i‐n one, with relatively long and comparable carrier diffusion lengths, while the single cation‐based bromide HaPs form clear p‐n junctions at the interface with the TiO₂ [pure CsPbBr₃ and MAPbBr₃(Cl)] or a buried one (MAPbBr₃) and shorter diffusion lengths. These differences are attributed to lower carrier density in MAPbBr₃, and especially in the mixed cation HaP, which is comparable to iodide‐based HaP films.     

Atomic‐Layer‐Deposited Aluminum and Zirconium Oxides for Surface Passivation of TiO2 in High‐Efficiency Organic Photovoltaics

The reduction in electronic recombination losses by the passivation of surfaces is a key factor enabling high‐efficiency solar cells. Here a strategy to passivate surface trap states of TiO₂ films used as cathode interlayers in organic photovoltaics (OPVs) through applying alumina (Al₂O₃) or zirconia (ZrO₂) insulating nanolayers by thermal atomic layer deposition (ALD) is investigated. The results suggest that the surface traps in TiO₂ are oxygen vacancies, which cause undesirable recombination and high electron extraction barrier, reducing the open‐circuit voltage and the short‐circuit current of the complete OPV device. It is found that the ALD metal oxides enable excellent passivation of the TiO₂ surface followed by a downward shift of the conduction band minimum. OPV devices based on different photoactive layers and using the passivated TiO₂ electron extraction layers exhibit a significant enhancement of more than 30% in their power conversion efficiencies compared to their reference devices without the insulating metal oxide nanolayers. This is a result of significant suppression of charge recombination and enhanced electron extraction rates at the TiO₂/ALD metal oxide/organic interface.     

TiO2 Nanocrystals Synthesized by Laser Pyrolysis for the Up‐Scaling of Efficient Solid‐State Dye‐Sensitized Solar Cells

A crucial issue regarding emerging nanotechnologies remains the up‐scaling of new functional nanostructured materials towards their implementation in high performance applications on a large scale. In this context, we demonstrate high efficiency solid‐state dye‐sensitized solar cells prepared from new porous TiO₂ photoanodes based on laser pyrolysis nanocrystals. This strategy exploits a reduced number of processing steps as well as non‐toxic chemical compounds to demonstrate highly porous TiO₂ films. The possibility to easily tune the TiO₂ nanocrystal physical properties allows us to demonstrate all solid‐state dye‐sensitized devices based on a commercial benchmark materials (organic indoline dye and molecular hole transporter) presenting state‐of‐the‐art performance comparable with reference devices based on a commercial TiO₂ paste. In particular, a drastic improvement in pore infiltration, which is found to balance a relatively lower surface area compared to the reference electrode, is evidenced using laser‐synthesized nanocrystals resulting in an improved short‐circuit current density under full sunlight. Transient photovoltage decay measurements suggest that charge recombination kinetics still limit device performance. However, the proposed strategy emphasizes the potentialities of the laser pyrolysis technique for up‐scaling nanoporous TiO₂ electrodes for various applications, especially for solar energy conversion.     

Single‐Step Preparation of Large Area TiO2 Photoelectrodes for Water Splitting

The fast, single‐step and easily scalable production by plasma electrolytic oxidation (PEO) of large area TiO₂ electrodes with excellent photoactivity in water splitting under simulated solar light is systematically investigated here. In particular, the effects that the cell voltage (100–180 V) and the processing time (0.5–15 min) have on the electrode properties are studied. The PEO‐produced oxide layers are porous, the predominant crystalline structure shifting from anatase, to an anatase‐rutile mixture, and finally to rutile by rising the cell voltage. The electrodes show a double‐layered structure, with a more compact layer at the interface with the titanium substrate and a thick porous layer on the external surface. The photocurrent density versus wavelength reflects the phase composition, with a maximum incident photon‐to‐current efficiency of 90% at 320 nm. The highest H₂ production rate is attained with the mixed anatase‐rutile electrode prepared by 300 s‐long PEO at 150 V.     

Overcoming the “Light‐Soaking” Issue in Inverted Organic Solar Cells by the Use of Al:ZnO Electron Extraction Layers

A common phenomenon of organic solar cells (OSCs) incorporating metal‐oxide electron extraction layers is the requirement to expose the devices to UV light in order to improve device characteristics – known as the so‐called “light‐soaking” issue. This behaviour appears to be of general validity for various metal‐oxide layers, various organic donor/acceptor systems, and regardless if single junction devices or multi stacked cells are considered. The requirement of UV exposure of OSCs may impose severe problems if substrates with limited UV transmission, UV blocking filters or UV to VIS down‐conversion concepts are applied. In this paper, we will demonstrate that this issue can be overcome by the use of Al doped ZnO (AZO) as electron extraction interlayer. In contrast to devices based on TiO_x and ZnO, the AZO devices show well‐behaved solar cell characteristics with a high fill factor (FF) and power conversion efficiency (PCE) even without the UV spectral components of the AM1.5 solar spectrum. As opposed to previous claims, our results indicate that the origin of s‐shaped characteristics of the OSCs is the metal‐oxide/organic interface. The electronic structures of the TiO_x/fullerene and AZO/fullerene interfaces are studied by photoelectron spectroscopy, revealing an electron extraction barrier for the TiO_x/fullerene case and facilitated electron extraction for AZO/fullerene. These results are of general relevance for organic solar cells based on various donor acceptor active systems.     

Titanium Dioxide Mesoporous Electrodes for Solid‐State Dye‐Sensitized Solar Cells: Cross‐Analysis of the Critical Parameters

We report a comparative study on the use of four different mesoporous titanium dioxide (TiO₂) photo‐electrodes for the fabrication of solid‐state dye‐sensitized solar cells (sDSSCs). The photovoltaic parameters of the device correlate with several intrinsic properties of the film, based not only on its morphological features, as commonly considered in standard characterizations, but also on the transport and the electronic properties of the photo‐electrode. These properties differ significantly for TiO₂ electrodes processed using different colloidal pastes, and are decisive for the photovoltaic efficiency, ranging from 3.7% up to 5.1%. In particular, the dielectric permittivity of each mesoporous layer (ε_eff) and the number of traps (N_t) determined by the space‐charge‐limited current (SCLC) theory are found to be a bottle‐neck for the charge transport, greatly influencing the fill factor (FF) and open circuit voltage (V_oc) of the cells. In addition, a direct correlation between TiO₂ surface potential with the V_oc was established. Cross‐analysis of key macroscopic parameters of the films prior to integration in the devices, in particular focusing on the determination of the capacitance and surface potential shift of the TiO₂ mesoporous anode, represents a straightforward yet powerful method to screen and select the most suitable TiO₂ for applications in sDSSCs.     

Origin of the S‐Shaped JV Curve and the Light‐Soaking Issue in Inverted Organic Solar Cells

Inverted organic solar cells generally exhibit a strong s‐shaped kink in the current–voltage characteristics (JV curve) that may be removed by exposure to UV light (light‐soaking) leading to a drastically improved performance. Using in‐device characterization methods the origin of the light‐soaking issue in inverted solar cells employing titanium dioxide (TiO₂) as an electron selective layer is clarified. An injected hole reservoir accumulated at the TiO₂/organic interface of the pristine device is observed from extraction current transients; the hole reservoir increases the recombination and results in an s‐shape in the JV curve of pristine devices. The hole reservoir and the s‐shape is a result of the energetics at the selective contact in the pristine device; the effect of UV exposure is to decrease the work function of the indium tin oxide/TiO₂‐contact, increasing the built‐in potential. This hinders the build‐up of the hole reservoir and the s‐shape is removed. The proposed model is in excellent agreement with drift‐diffusion simulations.     

Efficient Li‐Ion‐Conductive Layer for the Realization of Highly Stable High‐Voltage and High‐Capacity Lithium Metal Batteries

Recently, a consensus has been reached that using lithium metal as an anode in rechargeable Li‐ion batteries is the best way to obtain the high energy density necessary to power electronic devices. Challenges remain, however, with respect to controlling dendritic Li growth on these electrodes, enhancing compatibility with carbonate‐based electrolytes, and forming a stable solid–electrolyte interface layer. Herein, a groundbreaking solution to these challenges consisting in the preparation of a Li₂TiO₃ (LT) layer that can be used to cover Li electrodes via a simple and scalable fabrication method, is suggested. Not only does this LT layer impede direct contact between electrode and electrolyte, thus avoiding side reactions, but it assists and expedites Li‐ion flux in batteries, thus suppressing Li dendrite growth. Other effects of the LT layer on electrochemical performance are investigated by scanning electron microscopy, electrochemical impedance spectroscopy, and galvanostatic intermittent titration technique analyses. Notably, LT layer‐incorporating Li cells comprising high‐capacity/voltage cathodes with reasonably high mass loading (LiNi_0.8Co_0.1Mn_0.1O₂, LiNi_0.5Mn_1.5O₄, and LiMn₂O₄) show highly stable cycling performance in a carbonate‐based electrolyte. Therefore, it is believed that the approach based on the LT layer can boost the realization of high energy density lithium metal batteries and next‐generation batteries.     

Triblock‐Terpolymer‐Directed Self‐Assembly of Mesoporous TiO2: High‐Performance Photoanodes for Solid‐State Dye‐Sensitized Solar Cells

A new self‐assembly platform for the fast and straightforward synthesis of bicontinuous, mesoporous TiO₂ films is presented, based on the triblock terpolymer poly(isoprene ‐ b ‐ styrene ‐ b ‐ ethylene oxide). This new materials route allows the co‐assembly of the metal oxide as a fully interconnected minority phase, which results in a highly porous photoanode with strong advantages over the state‐of‐the‐art nanoparticle‐based photoanodes employed in solid‐state dye‐sensitized solar cells. Devices fabricated through this triblock terpolymer route exhibit a high availability of sub‐bandgap states distributed in a narrow and low enough energy band, which maximizes photoinduced charge generation from a state‐of‐the‐art organic dye, C220. As a consequence, the co‐assembled mesoporous metal oxide system outperformed the conventional nanoparticle‐based electrodes fabricated and tested under the same conditions, exhibiting solar power‐conversion efficiencies of over 5%.     

MXene‐Contacted Silicon Solar Cells with 11.5% Efficiency

MXene, a new class of 2D materials, has gained significant attention owing to its attractive electrical conductivity, tunable work function, and metallic nature for wide range of applications. Herein, delaminated few layered Ti₃C₂T_x MXene contacted Si solar cells with a maximum power conversion efficiency (PCE) of ≈11.5% under AM1.5G illumination are demonstrated. The formation of an Ohmic junction of the metallic MXene to n⁺‐Si surface efficiently extracts the photogenerated electrons from n⁺np⁺‐Si, decreases the contact resistance, and suppresses the charge carrier recombination, giving rise to excellent open‐circuit voltage and short‐circuit current density. The rapid thermal annealing process further improves the electrical contact between Ti₃C₂T_x MXene and n⁺‐Si surface by reducing sheet resistance, increasing electrical conductivity, and decreasing cell series resistance, thus leading to a remarkable improvement in fill factor and overall PCE. The work demonstrated here can be extended to other MXene compositions as potential electrodes for developing highly performing solar cells.     

Enhanced Efficiency and Stability of Perovskite Solar Cells Through Nd‐Doping of Mesostructured TiO2

Block‐copolymer templated chemical solution deposition is used to prepare mesoporous Nd‐doped TiO₂ electrodes for perovskite‐based solar cells. X‐ray diffraction and photothermal deflection spectroscopy show substitutional incorporation into the TiO₂ crystal lattice for low Nd concentration, and increasing interstitial doping for higher concentrations. Substitutional Nd‐doping leads to an increase in stability and performance of perovskite solar cells by eliminating defects and thus increasing electron transport and reducing charge recombination in the mesoporous TiO₂. The optimized doping concentration of 0.3% Nd enables the preparation of perovskite solar cells with stabilized power conversion efficiency of >18%.     

Nanowire‐Based Three‐Dimensional Transparent Conducting Oxide Electrodes for Extremely Fast Charge Collection

A 3D transparent conducting oxide (3D‐TCO) has been fabricated by growing Sn‐doped indium oxide (ITO) nanowire arrays on glass substrates via a vapor transport method. The 3D TCO charge‐collection properties have been compared to those of conventional two‐dimensional TCO (2D‐TCO) thin films. For use as a photoelectrode in dye‐sensitized solar cells, ITO‐TiO₂ core‐shell nanowire arrays were prepared by depositing a 45 nm‐thick mesoporous TiO₂ shell layer consisting of ～6 nm anatase nanoparticles using TiCl₄ treatments. Dye‐sensitized solar cells fabricated using these ITO‐TiO₂ core‐shell nanowire arrays show extremely fast charge collection owing to the shorter electron paths across the 45 nm‐thick TiO₂ shell compared to the 2D TCO. Interestingly, the charge‐collection time does not increase with the overall electrode thickness, which is counterintuitive to conventional diffusion models. This result implies that, in principle, maximum light harvesting can be achieved without hindering the charge collection. The proposed new 3D TCO should also be attractive for other photovoltaic applications where the active layer thickness is limited by poor charge collection.     

Surface Engineering of TiO2 ETL for Highly Efficient and Hysteresis‐Less Planar Perovskite Solar Cell (21.4%) with Enhanced Open‐Circuit Voltage and Stability

Interfacial studies and band alignment engineering on the electron transport layer (ETL) play a key role for fabrication of high‐performance perovskite solar cells (PSCs). Here, an amorphous layer of SnO₂ (a‐SnO₂) between the TiO₂ ETL and the perovskite absorber is inserted and the charge transport properties of the device are studied. The double‐layer structure of TiO₂ compact layer (c‐TiO₂) and a‐SnO₂ ETL leads to modification of interface energetics, resulting in improved charge collection and decreased carrier recombination in PSCs. The optimized device based on a‐SnO₂/c‐TiO₂ ETL shows a maximum power conversion efficiency (PCE) of 21.4% as compared to 19.33% for c‐TiO₂ based device. Moreover, the modified device demonstrates a maximum open‐circuit voltage (V_oc) of 1.223 V with 387 mV loss in potential, which is among the highest reported value for PSCs with negligible hysteresis. The stability results show that the device on c‐TiO₂/a‐SnO₂ retains about 91% of its initial PCE value after 500 h light illumination, which is higher than pure c‐TiO₂ (67%) based devices. Interestingly, using a‐SnO₂/c‐TiO₂ ETL the PCE loss was only 10% of initial value under continuous UV light illumination after 30 h, which is higher than that of c‐TiO₂ based device (28% PCE loss).     

Efficient Nanostructured TiO2/SnS Heterojunction Solar Cells

Tin sulfide (SnS) is one of the most promising solar cell materials, as it is abundant, environment friendly, available at low cost, and offers long‐term stability. However, the highest efficiency of the SnS solar cell reported so far remains at 4.36% even using the expensive atomic layer deposition process. This study reports on the fabrication of SnS solar cells by a solution process that employs rapid thermal treatment for few seconds under Ar gas flow after spin‐coating a precursor solution of SnCl₂ and thiourea dissolved in dimethylformamide onto a nanostructured thin TiO₂ electrode. The best‐performing cell exhibits power conversion efficiency (PCE) of 3.8% under 1 sun radiation conditions (AM1.5G). Moreover, secondary treatment using SnCl₂ results in a significant improvement of 4.8% in PCE, which is one of the highest efficiencies among SnS‐based solar cells, especially with TiO₂ electrodes. The thin film properties of SnS after SnCl₂ secondary treatment are analyzed using grazing‐incidence wide‐angle X‐ray scattering, and high‐resolution transmittance electron microscopy.