Building Lithiophilic Ion‐Conduction Highways on Garnet‐Type Solid‐State Li+ Conductors

The integration of highly conductive solid‐state electrolytes (SSEs) into solid‐state cells is still a challenge mainly due to the high impedance existing at the electrolyte/electrode interface. Although solid‐state garnet‐based batteries have been successfully assembled with the assistance of an intermediate layer between the garnet and the Li metal anode, the slow discharging/charging rates of the batteries inhibits practical applications, which require much higher power densities. Here, a crystalline sulfonated‐covalent organic framework (COF) thin layer is grown on the garnet surface via a simple solution process. It not only significantly improves the lithiophilicity of garnet electrolytes via the lithiation of the COF layer with molten Li, but also creates effective Li⁺ diffusion “highways” between the garnet and the Li metal anode. As a result, the interfacial impedance of symmetric solid‐state Li cells is significantly decreased and the cells can be operated at high current densities up to 3 mA cm^?2, which is difficult to achieve with current interfacial modification technologies for SSEs. The solid‐state Li‐ion batteries using LiFePO₄ cathodes, Li anodes, and COF‐modified garnet electrolytes thus exhibit a significantly improved rate capability.     

Germanium Thin Film Protected Lithium Aluminum Germanium Phosphate for Solid‐State Li Batteries

Solid‐state Li batteries using Na⁺ superionic conductor type solid electrolyte attracts wide interest because of its safety and high theoretical energy density. The NASCION type solid electrolyte LAGP (Li_1.5Al_0.5Ge_0.5P₃O₁₂) shows favorable conductivity as well as good mechanical strength to prevent Li dendrite penetration. However, the instability of LAGP with Li metal remains a great challenge. In this work, an amorphous Ge thin film is sputtered on an LAGP surface, which can not only suppress the reduction reaction of Ge⁴⁺ and Li, but also produces intimate contact between the Li metal and the LAGP solid electrolyte. The symmetric cell with the Ge‐coated LAGP solid electrolyte shows superior stability and cycle performance for 100 cycles at 0.1 mA cm^?2. A quasi‐solid‐state Li–air battery has also been assembled to further demonstrate this advantage. A stable cycling performance of 30 cycles in ambient air can be obtained. This work helps to achieve a stable and ionic conducting interface in solid‐state Li batteries.     

Interface‐Engineered All‐Solid‐State Li‐Ion Batteries Based on Garnet‐Type Fast Li+ Conductors

All‐solid‐state Li‐ion batteries based on Li₇La₃Zr₂O₁₂ (LLZO) garnet structures require novel electrode assembly strategies to guarantee a proper Li⁺ transfer at the electrode–electrolyte interfaces. Here, first stable cell performances are reported for Li‐garnet, c‐Li_6.25Al_0.25La₃Zr₂O₁₂, all‐solid‐state batteries running safely with a full ceramics setup, exemplified with the anode material Li₄Ti₅O₁₂. Novel strategies to design an enhanced Li⁺ transfer at the electrode–electrolyte interface using an interface‐engineered all‐solid‐state battery cell based on a porous garnet electrolyte interface structure, in which the electrode material is intimately embedded, are presented. The results presented here show for the first time that all‐solid‐state Li‐ion batteries with LLZO electrolytes can be reversibly charge–discharge cycled also in the low potential ranges (≈1.5 V) for combinations with a ceramic anode material. Through a model experiment, the interface between the electrode and electrolyte constituents is systematically modified revealing that the interface engineering helps to improve delivered capacities and cycling properties of the all‐solid‐state Li‐ion batteries based on garnet‐type cubic LLZO structures.     

Revealing the Short‐Circuiting Mechanism of Garnet‐Based Solid‐State Electrolyte

Garnet‐type solid‐state electrolytes (SSEs) have been widely studied as a promising candidate for Li metal batteries. Despite the common belief that inorganic SSEs can prevent dendrite propagation, garnet SSEs suffer from relatively low critical current density (CCD) at which the SSEs are abruptly short‐circuited by Li dendrites. In this study, the short‐circuiting mechanism of garnet Li₇La_2.75Ca_0.25Zr_1.75Nb_0.25O₁₂ (LLCZN) is investigated. It is found that instead of propagating uniaxially from one electrode to other in a dendritic form, metallic lithium is formed within the SSE. This can be attributed to the fact that electrons combine with Li ions at the grain boundary, which exhibits relatively high electronic conductivity, and then reduce Li⁺ to Li⁰ to cause short circuits. In order to reduce the electronic conductivity at the grain boundary, a thin layer of LiAlO₂ is coated on the grain surface of LLCZN, which results in an improved CCD value. It is also found that under higher external voltages, the electronic conductivity of SSE becomes more significant, which is believed to be the origin of CCD. These findings not only shed light on the short‐circuiting mechanism of garnet‐type SSEs but also offer a novel perspective and useful guidance on their designs and modifications.     

Reversible Short‐Circuit Behaviors in Garnet‐Based Solid‐State Batteries

Garnet‐based solid‐state electrolytes (SSEs) are attractive for solid‐state lithium metal batteries due to their wide electrochemical window, high conductivity, and excellent stability against lithium metal. However, the risk of short‐circuit encumbers the cycle life and capacity of garnet‐based solid‐state batteries without clear reason or mechanism. Here, reversible short‐circuit behavior in the garnet‐based solid‐state batteries, which differs from the short‐circuit in liquid cells, is reported for the first time. In situ neutron depth profiling is adopted to quantitatively measure Li transport, which helps forecast and confirm the reversible nature of the short‐circuit in garnet‐based batteries. A real‐time Li accumulation monitoring system of NMC//CNT/garnet/Li cell is designed to reveal the Li dendrite formation mechanism. The voltage drops of the CNT monitoring electrode during the charging process indicate the formation of Li dendrites inside the garnet bulk, while the smooth voltage profile during the discharging process demonstrates the disappearance of the short‐circuit. This is the first confirmation of short‐circuit behavior that provides clarification of the Li dendrite formation mechanism in garnet‐based solid‐state batteries, which is shown to be a reversible process caused by the low ionic conductivity and non‐negligible electronic conductivity of garnet SSEs.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

An Air‐Stable and Dendrite‐Free Li Anode for Highly Stable All‐Solid‐State Sulfide‐Based Li Batteries

Li metal is a promising anode material for all‐solid‐state batteries, owing to its high specific capacity and low electrochemical potential. However, direct contact of Li metal with most solid‐state electrolytes induces severe side reactions that can lead to dendrite formation and short circuits. Moreover, Li metal is unstable when exposed to air, leading to stringent processing requirements. Herein, it is reported that the Li₃PS₄/Li interface in all‐solid‐state batteries can be stabilized by an air‐stable Li_xSiS_y protection layer that is formed in situ on the surface of Li metal through a solution‐based method. Highly stable Li cycling for over 2000 h in symmetrical cells and a lifetime of over 100 cycles can be achieved for an all‐solid‐state LiCoO₂/Li₃PS₄/Li cell. Synchrotron‐based high energy X‐ray photoelectron spectroscopy in‐depth analysis demonstrates the distribution of different components within the protection layer. The in situ formation of an electronically insulating Li_xSiS_y protection layer with highly ionic conductivity provides an effective way to prevent Li dendrite formation in high‐energy all‐solid‐state Li metal batteries.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

Improvements to the Overpotential of All‐Solid‐State Lithium‐Ion Batteries during the Past Ten Years

After the research that shows that Li₁₀GeP₂S₁₂ (LGPS)‐type sulfide solid electrolytes can reach the high ionic conductivity at the room temperature, sulfide solid electrolytes have been intensively developed with regard to ionic conductivity and mechanical properties. As a result, an increasing volume of research has been conducted to employ all‐solid‐state lithium batteries in electric automobiles within the next five years. To achieve this goal, it is important to review the research over the past decade, and understand the requirements for future research necessary to realize the practical applications of all‐solid‐state lithium batteries. To date, research on all‐solid‐state lithium batteries has focused on achieving overpotential properties similar to those of conventional liquid‐lithium‐ion batteries by increasing the ionic conductivity of the solid electrolytes. However, the increase in the ionic conductivity should be accompanied by improvements of the electronic conductivity within the electrode to enable practical applications. This essay provides a critical overview of the recent progress and future research directions of the all‐solid‐state lithium batteries for practical applications.     

Sodium Plating from Na‐β″‐Alumina Ceramics at Room Temperature,Paving the Way for Fast‐Charging All‐Solid‐State Batteries

All‐solid‐state batteries with an alkali metal anode have the potential to achieve high energy density. However, the onset of dendrite formation limits the maximum plating current density across the solid electrolyte and prevents fast charging. It is shown that the maximum plating current density is related to the interfacial resistance between the solid electrolyte and the metal anode. Due to their high ionic conductivity, low electronic conductivity, and stability against sodium metal, Na‐β″‐alumina ceramics are excellent candidates as electrolytes for room‐temperature all‐solid‐state batteries. Here, it is demonstrated that a heat treatment of Na‐β″‐alumina ceramics in argon atmosphere enables an interfacial resistance <10 Ω cm² and current densities up to 12 mA cm^?2 at room temperature. The current density obtained for Na‐β″‐alumina is ten times higher than that measured on a garnet‐type Li₇La₃Zr₂O₁₂ electrolyte under equivalent conditions. X‐ray photoelectron spectroscopy shows that eliminating hydroxyl groups and carbon contaminations at the interface between Na‐β″‐alumina and sodium metal is key to reach such values. By comparing the temperature‐dependent stripping/plating behavior of Na‐β″‐alumina and Li₇La₃Zr₂O₁₂, the role of the alkali metal in governing interface kinetics is discussed. This study provides new insights into dendrite formation and paves the way for fast‐charging all‐solid‐state batteries.     

Fluorine‐Free Noble Salt Anion for High‐Performance All‐Solid‐State Lithium–Sulfur Batteries

Amongst post‐Li‐ion battery technologies, lithium–sulfur (Li–S) batteries have captured an immense interest as one of the most appealing devices from both the industrial and academia sectors. The replacement of conventional liquid electrolytes with solid polymer electrolytes (SPEs) enables not only a safer use of Li metal (Li°) anodes but also a flexible design in the shape of Li–S batteries. However, the practical implementation of SPEs‐based all‐solid‐state Li–S batteries (ASSLSBs) is largely hindered by the shuttling effect of the polysulfide intermediates and the formation of dendritic Li° during the battery operation. Herein, a fluorine‐free noble salt anion, tricyanomethanide [C(CN)₃^?, TCM^?], is proposed as a Li‐ion conducting salt for ASSLSBs. Compared to the widely used perfluorinated anions {e.g., bis(trifluoromethanesulfonyl)imide anion, [N(SO₂CF₃)₂)]^?, TFSI^?}, the LiTCM‐based electrolytes show decent ionic conductivity, good thermal stability, and sufficient anodic stability suiting the cell chemistry of ASSLSBs. In particular, the fluorine‐free solid electrolyte interphase layer originating from the decomposition of LiTCM exhibits a good mechanical integrity and Li‐ion conductivity, which allows the LiTCM‐based Li–S cells to be cycled with good rate capability and Coulombic efficiency. The LiTCM‐based electrolytes are believed to be the most promising candidates for building cost‐effective and high energy density ASSLSBs in the near future.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.     

Flexible Ion‐Conducting Composite Membranes for Lithium Batteries

The use of metallic lithium anodes enables higher energy density and higher specific capacity Li‐based batteries. However, it is essential to suppress lithium dendrite growth during electrodeposition. Li‐ion‐conducting ceramics (LICC) can mechanically suppress dendritic growth but are too fragile and also have low Li‐ion conductivity. Here, a simple, versatile, and scalable procedure for fabricating flexible Li‐ion‐conducting composite membranes composed of a single layer of LICC particles firmly embedded in a polymer matrix with their top and bottom surfaces exposed to allow for ionic transport is described. The membranes are thin (<100 μm) and possess high Li‐ion conductance at thicknesses where LICC disks are mechanically unstable. It is demonstrated that these membranes suppress Li dendrite growth even when the shear modulus of the matrix is lower than that of lithium. It is anticipated that these membranes enable the use of metallic lithium anodes in conventional and solid‐state Li‐ion batteries as well as in future Li? S and Li? O₂ batteries.     

A Lithium Oxythioborosilicate Solid Electrolyte Glass with Superionic Conductivity

As potential next‐generation energy storage devices, solid‐state lithium batteries require highly functional solid state electrolytes. Recent research is primarily focused on crystalline materials, while amorphous materials offer advantages by eliminating problematic grain boundaries that can limit ion transport and trigger dendritic growth at the Li anode. However, simultaneously achieving high conductivity and stability in glasses is a challenge. New quaternary superionic lithium oxythioborate glasses are reported that exhibit high ion conductivity up to 2 mS cm^?1 despite relatively high oxygen: sulfur ratios of more than 1:2, that exhibit greatly reduced H₂S evolution upon exposure to air compared to Li₇P₃S₁₁. These monolithic glasses are prepared from vitreous melts without ball‐milling and exhibit no discernable XRD pattern. Solid‐state NMR studies elucidate the structural entities that comprise the local glass structure which dictates fast ion conduction. Stripping/plating onto lithium metal results in very low polarization at a current density of 0.1 mA cm^?2 over repeated cycling. Evaluation of the optimal glass composition as an electrolyte in an all‐solid‐state battery shows it exhibits excellent cycling stability and maintains near theoretical capacity for over 130 cycles at room temperature with Coulombic efficiency close to 99.9%, opening up new avenues of exploration for these quaternary compositions.     

Nonuniform Ionic and Electronic Transport of Ceramic and Polymer/Ceramic Hybrid Electrolyte by Nanometer‐Scale Operando Imaging for Solid‐State Battery

Replacing the liquid electrolyte in lithium batteries with solid‐state ion conductor is promising for next‐generation energy storage that is safe and has high energy density. Here, nanometer‐resolution ionic and electronic transport imaging of Li₃PS₄ (LPS), a solid‐state electrolyte (SSE), is reported. This nm resolution is achieved by using a logarithm‐scale current amplifier that enhances the current sensitivity to the fA range. Large fluctuations of ion current—one to two orders of magnitude on the LPS and on the LPS region of a polymer/LPS bulk hybrid SSE—that must be mitigated to eliminate Li dendrite formation and growth, are found. This ion current fluctuation is understood in terms of highly anisotropic transport kinetic barriers along the different crystalline axes due to different grain orientations in the polycrystalline and glass ceramic materials. The results on the bulk hybrid SSE show a sharp transition of ionic and electronic transport at the LPS/polymer boundary and decreases in average ionic current with decreasing polyimine particle size and with extensive cycling. The results elucidate the mechanism of polyimine extension into interparticles to prevent Li dendrite growth. This work opens up novel characterization of charge transport, which relates to Li plating and stripping for solid‐state‐batteries.     

Dopant‐Dependent Stability of Garnet Solid Electrolyte Interfaces with Lithium Metal

Li₇La₃Zr₂O₁₂ (LLZO) garnet‐based materials doped with Al, Nb, or Ta to stabilize the Li⁺‐conductive cubic phase are a particularly promising class of solid electrolytes for all‐solid‐state lithium metal batteries. Understanding of the intrinsic reactivity between solid electrolytes and relevant electrode materials is crucial to developing high voltage solid‐state batteries with long lifetimes. Using a novel, surface science‐based approach to characterize the intrinsic reactivity of the Li–solid electrolyte interface, it is determined that, surprisingly, some degree of Zr reduction takes place for all three dopant types, with the extent of reduction increasing as Ta < Nb < Al. Significant reduction of Nb also takes place for Nb‐doped LLZO, with electrochemical impedance spectroscopy (EIS) of Li||Nb–LLZO||Li symmetric cells further revealing significant increases in impedance with time and suggesting that the Nb reduction propagates into the bulk. Density functional theory (DFT) calculations reveal that Nb‐doped material shows a strong preference for Nb dopants toward the interface between LLZO and Li, while Ta does not exhibit a similar preference. EIS and DFT results, coupled with the observed reduction of Zr at the interface, are consistent with the formation of an “oxygen‐deficient interphase” (ODI) layer whose structure determines the stability of the LLZO–Li interface.     

Aqueous Solution‐Processable Small Molecular Metal‐Chelate Complex Electrolyte for Flexible All‐Solid State Energy Storage Devices

A small molecular metal‐chelate complex, tris(8‐hydroxyquinoline‐5‐sulfonic acid) aluminum (AlQSA₃), that has three sulfonic acid groups per molecule leading to an excellent solubility in water is reported as a liquid‐free perfect solid‐state electrolyte for flexible film‐type all‐solid‐state energy storage devices. The AlQSA₃ material is synthesized by one‐step reaction of aluminum triisopropoxide and 8‐hydroxyquinoline‐5‐sulfonic acid. The aqueous solutions of AlQSA₃ are applied to fabricate flexible film‐type all‐solid state electric double layer capacitors with indium‐tin oxide thin film electrodes. The ion conductivity of the AlQSA₃ film reaches 0.116 mS cm^?1, while a pronounced hysteresis are obtained in the cyclic voltammetry measurement. The AlQSA₃ film capacitors exhibit an output voltage of 1.5 V at 20 μA cm^?2, which is considerably stable by the repeated operation. In particular, the peak output voltage is well kept even after 180° bending for 500 times in the case of the flexible AlQSA₃ film capacitors.     

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

Stable and seamless interfaces among solid components in all‐solid‐state batteries (ASSBs) are crucial for high ionic conductivity and high rate performance. This can be achieved by the combination of functional inorganic material and flexible polymer solid electrolyte. In this work, a flexible all‐solid‐state composite electrolyte is synthesized based on oxygen‐vacancy‐rich Ca‐doped CeO₂ (Ca–CeO₂) nanotube, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and poly(ethylene oxide) (PEO), namely Ca–CeO₂/LiTFSI/PEO. Ca–CeO₂ nanotubes play a key role in enhancing the ionic conductivity and mechanical strength while the PEO offers flexibility and assures the stable seamless contact between the solid electrolyte and the electrodes in ASSBs. The as‐prepared electrolyte exhibits high ionic conductivity of 1.3 × 10^?4 S cm^?1 at 60 °C, a high lithium ion transference number of 0.453, and high‐voltage stability. More importantly, various electrochemical characterizations and density functional theory (DFT) calculations reveal that Ca–CeO₂ helps dissociate LiTFSI, produce free Li ions, and therefore enhance ionic conductivity. The ASSBs based on the as‐prepared Ca–CeO₂/LiTFSI/PEO composite electrolyte deliver high‐rate capability and high‐voltage stability.