Influence of Oxides on the Stress Evolution and Reversibility during SnOx Conversion and Li‐Sn Alloying Reactions

The effect of varying the oxygen content in Sn and SnO_x films during potential dependent SnO_x conversion reactions and Li_ySn alloying relevant to Li ion battery anodes is examined. For metallic Sn films, the stresses and stability of the films are controlled by Li alloying reactions. Small, non‐contacting separated Sn particles exhibit higher electrochemical stability relative to more continuous polycrystalline films with larger particles. Metallic Sn particles develop tensile stress during Li_ySn de‐alloying as porous structures are formed. The amount of stress associated with lithiation and delithiation of well‐separated metallic particles decreases as a porous, easy to lithiate, material forms with cycling. During the lithiation of oxides, conversion reactions (SnO_x → Sn) and the lithiation of the metallic Sn control the stress responses of the films, leading to highly potential‐dependent stress development. In particular, evidence for a multistep electrochemical mechanism, in which partially reversible lithiation of the oxygen‐containing phases is conjoined with a fully reversible lithiation of the metallic phases of the Sn, is found. The electrochemical stress analysis provides new insight into these mechanisms and delineates the extent of the reversibility of lithiation and conversion reactions of oxides.     

Low‐Temperature Solution‐Based Phosphorization Reaction Route to Sn4P3/Reduced Graphene Oxide Nanohybrids as Anodes for Sodium Ion Batteries

Different from previously reported mechanical alloying route to synthesize Sn _x P₃, novel Sn₄P₃/reduced graphene oxide (RGO) hybrids are synthesized for the first time through an in situ low‐temperature solution‐based phosphorization reaction route from Sn/RGO. Sn₄P₃ nanoparticles combining with advantages of high conductivity of Sn and high capacity of P are homogenously loaded on the RGO nanosheets, interconnecting to form 3D mesoporous architecture nanostructures. The Sn₄P₃/RGO hybrid architecture materials exhibit significantly improved electrochemical performance of high reversible capacity, high‐rate capability, and excellent cycling performance as sodium ion batteries (SIBs) anode materials, showing an excellent reversible capacity of 656 mA h g^?1 at a current density of 100 mA g^?1 over 100 cycles, demonstrating a greatly enhanced rate capability of a reversible capacity of 391 mA h g^?1 even at a high current density of 2.0 A g^?1. Moreover, Sn₄P₃/RGO SIBs anodes exhibit a superior long cycling life, delivering a high capacity of 362 mA h g^?1 after 1500 cycles at a high current density of 1.0 A g^?1. The outstanding cycling performance and rate capability of these porous hierarchical Sn₄P₃/RGO hybrid anodes can be attributed to the advantage of porous structure, and the synergistic effect between Sn₄P₃ nanoparticles and RGO nanosheets.     

Operando Quantification of (De)Lithiation Behavior of Silicon–Graphite Blended Electrodes for Lithium‐Ion Batteries

Due to the high lithium capacity of silicon, the composite (blended) electrodes containing silicon (Si) and graphite (Gr) particles are attractive alternatives to the all‐Gr electrodes used in conventional lithium‐ion batteries. In this Communication, the lithiation and delithiation in the Si and Gr particles in a 15 wt% Si composite electrode is quantified for each component using energy dispersive X‐ray diffraction. This quantification is important as the components cycle in different potential regimes, and interpretation of cycling behavior is complicated by the potential hysteresis displayed by Si. The lithiation begins with Li alloying with Si; lithiation of Gr occurs at later stages when the potential dips below 0.2 V (all potentials are given vs Li/Li⁺). In the 0.2–0.01 V range, the relative lithiation of Si and Gr is ≈58% and 42%, respectively. During delithiation, Li⁺ ion extraction occurs preferentially from Gr in the 0.01–0.23 V range and from Si in the 0.23–1.0 V range; that is, the delithiation current is carried sequentially, first by Gr and then by Si. These trends can be used for rational selection of electrochemical cycling windows that limits volumetric expansion in Si particles, thereby extending cell life.     

3D Porous Cu–Zn Alloys as Alternative Anode Materials for Li‐Ion Batteries with Superior Low T Performance

Zinc is recently gaining interest in the battery community as potential alternative anode material, because of its large natural abundance and potentially larger volumetric density than graphite. Nevertheless, pure Zn anodes have shown so far very poor cycling performance. Here, the electrochemical performance of Zn‐rich porous Cu–Zn alloys electrodeposited by an environmentally friendly (aqueous) dynamic hydrogen bubble template method is reported. The lithiation/delithiation mechanism is studied in detail by both in situ and ex situ X‐ray diffraction, indicating the reversible displacement of Zn from the Cu–Zn alloy upon reaction with Li. The influence of the alloy composition on the performance of carbon‐ and binder‐free electrodes is also investigated. The optimal Cu:Zn atomic ratio is found to be 18:82, which provides impressive rate capability up to 10 A g^?1 (≈30C), and promising capacity retention upon more than 500 cycles. The high electronic conductivity provided by Cu, and the porous electrode morphology also enable superior lithium storage capability at low temperature. Cu₁₈Zn₈₂ can indeed steadily deliver ≈200 mAh g^?1 at ?20 °C, whereas an analogous commercial graphite electrode rapidly fades to only 12 mAh g^?1.     

Electrochemical Reaction of Lithium with Nanostructured Silicon Anodes: A Study by In‐Situ Synchrotron X‐Ray Diffraction and Electron Energy‐Loss Spectroscopy

Silicon‐based anodes are an appealing alternative to graphite for lithium‐ion batteries because of their extremely high capacity. However, poor cycling stability and slow kinetics continue to limit the widespread use of silicon in commercial batteries. Performance improvement has been often demonstrated in nanostructured silicon electrodes, but the reaction mechanisms involved in the electrochemical lithiation of nanoscale silicon are not well understood. Here, in‐situ synchrotron X‐ray diffraction is used to monitor the subtle structural changes occurring in Si nanoparticles in a Si‐C composite electrode during lithiation. Local analysis by electron energy‐loss spectroscopy and transmission electron microscopy is performed to interrogate the nanoscale morphological changes and phase evolution of Si particles at different depths of discharge. It is shown that upon lithiation, Si nanoparticles behave quite differently than their micrometer‐sized counterparts. Although both undergo an electrochemical amorphization, the micrometer‐sized silicon exhibits a linear transformation during lithiation, while a two‐step process occurs in the nanoscale Si. In the first half of the discharge, lithium reacts with surfaces, grain boundaries and planar defects. As the reaction proceeds and the cell voltage drops, lithium consumes the crystalline core transforming it into amorphous Li_xSi with a primary particle size of just a few nanometers. Unlike the bulk silicon electrode, no Li₁₅Si₄ or other crystalline Li_xSi phases were formed in nanoscale Si at the fully‐lithiated state.     

On the Capacity Losses Seen for Optimized Nano‐Si Composite Electrodes in Li‐Metal Half‐Cells

While the use of silicon‐based electrodes can increase the capacity of Li‐ion batteries considerably, their application is associated with significant capacity losses. In this work, the influences of solid electrolyte interphase (SEI) formation, volume expansion, and lithium trapping are evaluated for two different electrochemical cycling schemes using lithium‐metal half‐cells containing silicon nanoparticle–based composite electrodes. Lithium trapping, caused by incomplete delithiation, is demonstrated to be the main reason for the capacity loss while SEI formation and dissolution affect the accumulated capacity loss due to a decreased coulombic efficiency. The capacity losses can be explained by the increasing lithium concentration in the electrode causing a decreasing lithiation potential and the lithiation cut‐off limit being reached faster. A lithium‐to‐silicon atomic ratio of 3.28 is found for a silicon electrode after 650 cycles using 1200 mAhg^?1 capacity limited cycling. The results further show that the lithiation step is the capacity‐limiting step and that the capacity losses can be minimized by increasing the efficiency of the delithiation step via the inclusion of constant voltage delithiation steps. Lithium trapping due to incomplete delithiation consequently constitutes a very important capacity loss phenomenon for silicon composite electrodes.     

Storage Capacity and Cycling Stability in Ge Anodes: Relationship of Anode Structure and Cycling Rate

Operando X‐ray diffraction (XRD) and X‐ray absorption spectroscopy (XAS) studies of Ge anodes are carried out to understand the effect of cycling rate on Ge phase transformation during charge/discharge process and to relate that effect to capacity. It is discovered that the formation of crystalline Li₁₅Ge₄ (c‐Li₁₅Ge₄) during lithiation is suppressed beyond a certain cycling rate. A very stable and reversible high capacity of ≈1800 mAh g^?1 can be attained up to 100 cycles at a slow C‐rate of C/21 when there is complete conversion of Ge anode into c‐Li₁₅Ge₄. When the C‐rate is increased to ≈C/10, the lithiation reaction is more heterogeneous and a relatively high capacity of ≈1000 mAh g^?1 is achieved with poorer electrochemical reversibility. An increase in C‐rate to C/5 and higher reduces the capacity (≈500 mAh g^?1) due to an impeded transformation from amorphous Li_xGe to c‐Li₁₅Ge₄, and yet improves the electrochemical reversibility. A proposed mechanism is presented to explain the C‐rate dependent phase transformations and the relationship of these to capacity fading. The operando XRD and XAS results provide new insights into the relationship between structural changes in Ge and battery capacity, which are important for guiding better design of high‐capacity anodes.     

Insights into Ionic Transport and Structural Changes in Magnetite during Multiple‐Electron Transfer Reactions

Metal oxides, such as Fe₃O₄, hold promise for future battery applications due to their abundance, low cost, and opportunity for high lithium storage capacity. In order to better understand the mechanisms of multiple‐electron transfer reactions leading to high capacity in Fe₃O₄, a comprehensive investigation on local ionic transport and ordering is made by probing site occupancies of anions (O^2?) and cations (Li⁺, Fe³⁺/Fe²⁺) using multiple synchrotron X‐ray and electron‐beam techniques, in combination with ab‐initio calculations. Results from this study provide the first experimental evidence that the cubic‐close‐packed (ccp) O‐anion array in Fe₃O₄ is sustained throughout the lithiation and delithiation processes, thereby enabling multiple lithium intercalation and conversion reactions. Cation displacement/reordering occurs within the ccp O‐anion framework, which leads to a series of phase transformations, starting from the inverse spinel phase and turning into intermediate rock‐salt‐like phases (Li_xFe₃O₄; 0 < x < 2), then into a cation‐segregated phase (Li₂O?FeO), and finally converting into metallic Fe and Li₂O. Subsequent delithiation and lithiation processes involve interconversion between metallic Fe and FeO‐like phases. These results may offer new insights into the structure‐determined ionic transport and electrochemical reactions in metal oxides, and those of other compounds sharing a ccp anion framework, reminiscent of magnetite.     

Vanadate‐Based Materials for Li‐Ion Batteries: The Search for Anodes for Practical Applications

While the practical application of electrode materials depends intensively on the Li⁺ ion storage mechanisms correlating ultimately with the coulombic efficiency, reversible capacity, and morphology variation of electrode material upon cycling, only intercalation‐type electrode materials have proven viable for commercialization up to now. This paper reviews the promising anode materials of metal vanadates (M_xV_yO_z, M = Co, Cu, Mn, Fe, Zn, Ni, Li) that have high capacity, low cost, and abundant resource, and also discusses the related Li⁺ ion storage mechanism. It is concluded that most of these (M_xV_yO_z, M = Co, Cu, Mn, Fe, Zn, Ni) exhibit irreversible redox reactions upon lithiation/delithiation accompanied by large volume expansion, which is not favorable for industrial applications. In particular, Li₃VO₄ with specific intercalation Li⁺ ion storage mechanism and compatible merits of safety and energy density exhibits great potential for practical application. This review systematically summarizes the latest progress in Li₃VO₄ research, including the representative fabrication approaches for advanced morphology and state‐of‐the‐art technologies to boost performance and the morphology variation associated with Li⁺ ion storage mechanisms. Furthermore, an outlook on where breakthroughs for Li₃VO₄ may be most likely achieved will be provided.     

Solid‐State Prelithiation Enables High‐Performance Li‐Al‐H Anode for Solid‐State Batteries

Lithium alanates exhibit high theoretical specific capacities and appropriate lithiation/delithiation potentials, but suffer from poor reversibility, cycling stability, and rate capability due to their sluggish kinetics and extensive side reactions. Herein, a novel and facile solid‐state prelithiation approach is proposed to in situ prepare a Li₃AlH₆‐Al nanocomposite from a short‐circuited electrochemical reaction between LiAlH₄ and Li with the help of fast electron and Li‐ion conductors (C and P6₃mc LiBH₄). This nanocomposite consists of dispersive Al nanograins and an amorphous Li₃AlH₆ matrix, which enables superior electrochemical performance in solid‐state cells, as much higher specific capacity (2266 mAh g^?1), Coulombic efficiency (88%), cycling stability (71% retention in the 100th cycle), and rate capability (1429 mAh g^?1 at 1 A g^?1) are achieved. In addition, this nanocomposite works well in the solid‐state full cell with LiCoO₂ cathode, demonstrating its promising application prospects. Mechanism analysis reveals that the dispersive Al nanograins and amorphous Li₃AlH₆ matrix can dramatically enhance the lithiation and delithiation kinetics without side reactions, which is mainly responsible for the excellent overall performance. Moreover, this solid‐state prelithiation approach is general and can also be applied to other Li‐poor electrode materials for further modification of their electrochemical behavior.     

New Na‐Ion Solid Electrolytes Na4−xSn1−xSbxS4 (0.02 ≤ x ≤ 0.33) for All‐Solid‐State Na‐Ion Batteries

Sulfide Na‐ion solid electrolytes (SEs) are key to enable room‐temperature operable all‐solid‐state Na‐ion batteries that are attractive for large‐scale energy storage applications. To date, few sulfide Na‐ion SEs have been developed and most of the SEs developed contain P and suffer from poor chemical stability. Herein, discovery of a new structural class of tetragonal Na_4?xSn_1?xSb_xS₄ (0.02 ≤ x ≤ 0.33) with space group I4₁/acd is described. The evolution of a new phase, distinctly different from Na₄SnS₄ or Na₃SbS₄, allows fast ionic conduction in 3D pathways (0.2–0.5 mS cm^?1 at 30 °C). Moreover, their excellent air stability and reversible dissolution in water and precipitation are highlighted. Specifically, TiS₂/Na–Sn all‐solid‐state Na‐ion batteries using Na_3.75Sn_0.75Sb_0.25S₄ demonstrates high capacity (201 mA h (g of TiS₂)^?1) with excellent reversibility.     

In Operando Strain Measurement of Bicontinuous Silicon‐Coated Nickel Inverse Opal Anodes for Li‐Ion Batteries

Elastic strains are measured in operando in a nanostructured silicon‐coated nickel inverse opal scaffold anode, using X‐ray diffraction to study the Si (de)lithiation‐induced Ni strains. The volume expansion upon lithiation of the Si in the anode is constrained by the surrounding Ni scaffold, causing mismatch stresses and strains in the Si and Ni phases during cycling. The Ni strains are measured in operando during (dis)charge cycles, using diffraction peak position and peak broadness to describe the distribution of strain in the Ni. During lithiation, compressive strains in the Ni first increase linearly with charge, after which a gradually decreasing strain rate is observed as the maximum lithiation state is approached; upon delithiation a similar process occurs. In‐plane average compressive strains on the order of 990 ± 40 με are measured in the Ni scaffold during lithiation, corresponding to compressive stresses of 215 ± 9 MPa. The decreasing strain rates and decreasing maximum and recovered strains suggest that plasticity in Ni and/or Si, as well as delamination between Ni and Si, may occur during cycling. Rate sensitivity in capacity is correlated with strain and a maximum Ni compressive stress of 230 ± 40 MPa is measured at the maximum state of lithiation.     

Insights into the Enhanced Cycle and Rate Performances of the F‐Substituted P2‐Type Oxide Cathodes for Sodium‐Ion Batteries

A series of F‐substituted Na_2/3Ni_1/3Mn_2/3O_2?xF_x (x = 0, 0.03, 0.05, 0.07) cathode materials have been synthesized and characterized by solid‐state ¹⁹F and ²³Na NMR, X‐ray photoelectron spectroscopy, and neutron diffraction. The underlying charge compensation mechanism is systematically unraveled by X‐ray absorption spectroscopy and electron energy loss spectroscopy (EELS) techniques, revealing partial reduction from Mn⁴⁺ to Mn³⁺ upon F‐substitution. It is revealed that not only Ni but also Mn participates in the redox reaction process, which is confirmed for the first time by EELS techniques, contributing to an increase in discharge specific capacity. The detailed structural transformations are also revealed by operando X‐ray diffraction experiments during the intercalation and deintercalation process of Na⁺, demonstrating that the biphasic reaction is obviously suppressed in the low voltage region via F‐substitution. Hence, the optimized sample with 0.05 mol f.u.^?1 fluorine substitution delivers an ultrahigh specific capacity of 61 mAh g^?1 at 10 C after 2000 cycles at 30 °C, an extraordinary cycling stability with a capacity retention of 75.6% after 2000 cycles at 10 C and 55 °C, an outstanding full battery performance with 89.5% capacity retention after 300 cycles at 1 C. This research provides a crucial understanding of the influence of F‐substitution on the crystal structure of the P2‐type materials and opens a new avenue for sodium‐ion batteries.     

High‐Performance Reversible Aqueous Zn‐Ion Battery Based on Porous MnOx Nanorods Coated by MOF‐Derived N‐Doped Carbon

Rechargeable aqueous zinc‐ion batteries (ZIBs) have been emerging as potential large‐scale energy storage devices due to their high energy density, low cost, high safety, and environmental friendliness. However, the commonly used cathode materials in ZIBs exhibit poor electrochemical performance, such as significant capacity fading during long‐term cycling and poor performance at high current rates, which significantly hinder the further development of ZIBs. Herein, a new and highly reversible Mn‐based cathode material with porous framework and N‐doping (MnO_x@N‐C) is prepared through a metal–organic framework template strategy. Benefiting from the unique porous structure, conductive carbon network, and the synergetic effect of Zn²⁺ and Mn²⁺ in electrolyte, the MnO_x@N‐C shows excellent cycling stability, good rate performance, and high reversibility for aqueous ZIBs. Specifically, it exhibits high capacity of 305 mAh g^?1 after 600 cycles at 500 mA g^?1 and maintains achievable capacity of 100 mAh g^?1 at a quite high rate of 2000 mA g^?1 with long‐term cycling of up to 1600 cycles, which are superior to most reported ZIB cathode materials. Furthermore, insight into the Zn‐storage mechanism in MnO_x@N‐C is systematically studied and discussed via multiple analytical methods. This study opens new opportunities for designing low‐cost and high‐performance rechargeable aqueous ZIBs.     

Redox Targeting of Anatase TiO2 for Redox Flow Lithium‐Ion Batteries

Anatase TiO₂ is an extensively studied anode material for lithium‐ion batteries because of its superior capability of storing Li⁺ electrochemically. Here reversible lithium storage of TiO₂ is achieved chemically using redox targeting reactions. In the presence of a pair of redox mediators, bis(pentamethylcyclopentadienyl)cobalt (CoCp^* ₂) and cobaltocene (CoCp₂) in an electrolyte, TiO₂ and its lithiated form Li _x TiO₂ can be reduced and oxidized by CoCp^* ₂ and CoCp₂ ⁺, respectively, which accompany Li⁺ insertion and extraction, albeit without attaching the TiO₂ onto the electrode. The reversible chemical lithiation/delithiation and the involved phase transitions are unambiguously confirmed using density functional theory (DFT) calculations, UV‐vis spectroscopy, X‐ray photoelectron spectoscopy (XPS), and Raman spectroscopy. A redox flow lithium‐ion battery (RFLB) half‐cell is assembled and evaluated, which is a critical step towards the development of RFLB full cells.     

Na‐Ion Intercalation and Charge Storage Mechanism in 2D Vanadium Carbide

2D vanadium carbide MXene containing surface functional groups (denoted as V₂CT_x , where T_x are surface functional groups) is synthesized and studied as anode material for Na‐ion batteries. V₂CT_x anode exhibits reversible charge storage with good cycling stability and high rate capability through electrochemical test. The charge storage mechanism of V₂CT_x material during Na⁺ intercalation/deintercalation and the redox reaction of vanadium are studied using a combination of synchrotron based X‐ray diffraction, hard X‐ray absorption near edge spectroscopy (XANES), and soft X‐ray absorption spectroscopy (sXAS). Experimental evidence of a major contribution of redox reaction of vanadium to the charge storage and the reversible capacity of V₂CT_x during sodiation/desodiation process are provided through V K ‐edge XANES and V L _2,3‐edge sXAS results. A correlation between the CO₃^2? content and the Na⁺ intercalation/deintercalation states in the V₂CT_x electrode observed from C and O K ‐edge in sXAS results implies that some additional charge storage reactions may take place between the Na⁺‐intercalated V₂CT_x and the carbonate‐based nonaqueous electrolyte. The results of this study provide valuable information for the further studies on V₂CT_x as anode material for Na‐ion batteries and capacitors.     

Sn‐Alloy Foil Electrode with Mechanical Prelithiation: Full‐Cell Performance up to 200 Cycles

Self‐supporting Sn foil is a promising high‐volumetric‐capacity anode for lithium ion batteries (LIBs), but it suffers from low initial Coulombic efficiency (ICE). Here, mechanical prelithiation is adopted to improve ICE, and it is found that Sn foils with coarser grains are prone to cause electrode damage. To mitigate damage and prepare thinner lithiated electrodes, 3Ag0.5Cu96.5Sn foil is used that has more refined grains (5–10 µm) instead of Sn (50–100 µm), where the abundant grain boundaries (GBs) offer more sliding systems to release stress and reduce deep fractures. Thus, the thickness of Li_x3Ag0.5Cu96.5Sn can be reduced to 50 µm, compared to 100 µm Li_xSn. When the foils contact open air, the Sn‐Li‐O(H) products are more stable than Li‐O(H), thus Li_x3Ag0.5Cu96.5Sn shows outstanding air stability. The as‐prepared 50 µm foil anode achieves stable 200 cycles in LiFePO₄//Li_x3Ag0.5Cu96.5Sn full cell (≈2.65 mAh cm^?2) and the capacity retention is 95%. Even at 5C, the capacity of Li_x3Ag0.5Cu96.5Sn is still up to ≈1.8 mAh cm^?2. The cycle life of NCM523//Li_x3Ag0.5Cu96.5Sn full cell exceeds that of NCM523//Li. Furthermore, 70 µm Li_x3Ag0.5Cu96.5Sn is used as double‐sided anode for a 3 cm × 2.8 cm pouch cell and its actual volumetric capacity density is 674 mAh cm^?3 after 50 cycles.     

A Dual‐Insertion Type Sodium‐Ion Full Cell Based on High‐Quality Ternary‐Metal Prussian Blue Analogs

Prussian blue analogs (PBAs) are especially investigated as superior cathodes for sodium‐ion batteries (SIBs) due to high theoretical capacity (≈170 mA h g^?1) with 2‐Na storage and low cost. However, PBAs suffer poor cyclability due to irreversible phase transition in deep charge/discharge states. PBAs also suffer low crystallinity, with considerable [Fe(CN)₆] vacancies, and coordinated water in crystal frameworks. Presently, a new chelating agent/surfactant coassisted crystallization method is developed to prepare high‐quality (HQ) ternary‐metal Ni_xCo_1?x[Fe(CN)₆] PBAs. By introducing inactive metal Ni to suppress capacity fading caused by excessive lattice distortion, these PBAs have tunable limits on depth of charge/discharge. HQ‐Ni_xCo_1?x[Fe(CN)₆] (x = 0.3) demonstrates the best reversible Na‐storage behavior with a specific capacity of ≈145 mA h g^?1 and a remarkably improved cycle performance, with ≈90% capacity retention over 600 cycles at 5 C. Furthermore, a dual‐insertion full cell on the cathode and NaTi₂(PO₄)₃ anode delivers reversible capacity of ≈110 mA h g^?1 at a current rate of 1.0 C without capacity fading over 300 cycles, showing promise as a high‐performance SIB for large‐scale energy‐storage systems. The ultrastable cyclability achieved in the lab and explained herein is far beyond that of any previously reported PBA‐based full cells.     

Review on Challenges and Recent Advances in the Electrochemical Performance of High Capacity Li‐ and Mn‐Rich Cathode Materials for Li‐Ion Batteries

Li and Mn‐rich layered oxides, xLi₂MnO₃·(1–x)LiMO₂ (M=Ni, Mn, Co), are promising cathode materials for Li‐ion batteries because of their high specific capacity that can exceed 250 mA h g^?1. However, these materials suffer from high 1^st cycle irreversible capacity, gradual capacity fading, low rate capability, a substantial charge‐discharge voltage hysteresis, and a large average discharge voltage decay during cycling. The latter detrimental phenomenon is ascribed to irreversible structural transformations upon cycling of these cathodes related to potentials ≥4.5 V required for their charging. Transition metal inactivation along with impedance increase and partial layered‐to‐spinel transformation during cycling are possible reasons for the detrimental voltage fade. Doping of Li, Mn‐rich materials by Na, Mg, Al, Fe, Co, Ru, etc. is useful for stabilizing capacity and mitigating the discharge‐voltage decay of xLi₂MnO₃·(1–x)LiMO₂ electrodes. Surface modifications by thin coatings of Al₂O₃, V₂O₅, AlF₃, AlPO₄, etc. or by gas treatment (for instance, by NH₃) can also enhance voltage and capacity stability during cycling. This paper describes the recent literature results and ongoing efforts from our groups to improve the performance of Li, Mn‐rich materials. Focus is also on preparation of cobalt‐free cathodes, which are integrated layered‐spinel materials with high reversible capacity and stable performance.     

An Air‐Stable and Dendrite‐Free Li Anode for Highly Stable All‐Solid‐State Sulfide‐Based Li Batteries

Li metal is a promising anode material for all‐solid‐state batteries, owing to its high specific capacity and low electrochemical potential. However, direct contact of Li metal with most solid‐state electrolytes induces severe side reactions that can lead to dendrite formation and short circuits. Moreover, Li metal is unstable when exposed to air, leading to stringent processing requirements. Herein, it is reported that the Li₃PS₄/Li interface in all‐solid‐state batteries can be stabilized by an air‐stable Li_xSiS_y protection layer that is formed in situ on the surface of Li metal through a solution‐based method. Highly stable Li cycling for over 2000 h in symmetrical cells and a lifetime of over 100 cycles can be achieved for an all‐solid‐state LiCoO₂/Li₃PS₄/Li cell. Synchrotron‐based high energy X‐ray photoelectron spectroscopy in‐depth analysis demonstrates the distribution of different components within the protection layer. The in situ formation of an electronically insulating Li_xSiS_y protection layer with highly ionic conductivity provides an effective way to prevent Li dendrite formation in high‐energy all‐solid‐state Li metal batteries.