Low‐Temperature Reduction Strategy Synthesized Si/Ti3C2 MXene Composite Anodes for High‐Performance Li‐Ion Batteries

Silicon is attracting enormous attention due to its theoretical capacity of 4200 mAh g^?1 as an anode for Li‐ion batteries (LIBs). It is of fundamental importance and challenge to develop low‐temperature reaction route to controllably synthesize Si/Ti₃C₂ MXene LIBs anodes. Herein, a novel and efficient strategy integrating in situ orthosilicate hydrolysis and a low‐temperature reduction process to synthesize Si/Ti₃C₂ MXene composites is reported. The hydrolysis of tetraethyl orthosilicate leads to homogenous nucleation and growth of SiO₂ nanoparticles on the surface of Ti₃C₂ MXene. Subsequently, SiO₂ nanoparticles are reduced to Si via a low‐temperature (200 °C) reduction route. Importantly, Ti₃C₂ MXene not only provides fast transfer channels for Li⁺ and electrons, but also relieves volume expansion of Si during cycling. Moreover, the characteristics of excellent pseudocapacitive performance and high conductivity of Ti₃C₂ MXene can synergistically contribute to the enhancement of energy storage performance. As expected, Ti₃C₂/Si anode exhibits an outstanding specific capacity of 1849 mAh g^?1 at 100 mA g^?1, even retaining 956 mAh g^?1 at 1 A g^?1. The low‐temperature synthetic route to Si/Ti₃C₂ MXene electrodes and involved battery‐capacitive dual‐model energy storage mechanism has potential in the design of novel high‐performance electrodes for energy storage devices.     

An Ion‐Exchange Promoted Phase Transition in a Li‐Excess Layered Cathode Material for High‐Performance Lithium Ion Batteries

A new approach to intentionally induce phase transition of Li‐excess layered cathode materials for high‐performance lithium ion batteries is reported. In high contrast to the limited layered‐to‐spinel phase transformation that occurred during in situ electrochemical cycles, a Li‐excess layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ is completely converted to a Li₄Mn₅O₁₂‐type spinel product via ex situ ion‐exchanges and a post‐annealing process. Such a layered‐to‐spinel phase conversion is examined using in situ X‐ray diffraction and in situ high‐resolution transmission electron microscopy. It is found that generation of sufficient lithium ion vacancies within the Li‐excess layered oxide plays a critical role for realizing a complete phase transition. The newly formed spinel material exhibits initial discharge capacities of 313.6, 267.2, 204.0, and 126.3 mAh g^?1 when cycled at 0.1, 0.5, 1, and 5 C (1 C = 250 mA g^?1), respectively, and can retain a specific capacity of 197.5 mAh g^?1 at 1 C after 100 electrochemical cycles, demonstrating remarkably improved rate capability and cycling stability in comparison with the original Li‐excess layered cathode materials. This work sheds light on fundamental understanding of phase transitions within Li‐excess layered oxides. It also provides a novel route for tailoring electrochemical performance of Li‐excess layered cathode materials for high‐capacity lithium ion batteries.     

Superior Lithium Storage Properties of β‐FeOOH

Several crystal forms of FeOOH are recently reported to be highly promising for lithium storage due to their high capacity, low cost, and environmental friendliness. In particular, β‐FeOOH has shown a capacity of ≈1000 mAh g^?1, which is comparable to other promising iron‐based anodes, such as Fe₂O₃ and Fe₃O_4. However, its storage mechanisms are unclear and the potential for further improvement remains unexplored. Here, it is shown that this material can have a very high reversible capacity of ≈1400 mAh g^?1, which is 20%–40% higher than Fe₂O₃ and Fe₃O₄. Such a high capacity is delivered from a series of reactions including intercalation and conversion reactions, formation/deformation of solid‐state electrolyte interface layers and interfacial storage. The mechanisms are studied by a combination of electrochemical and X‐ray absorption near edge spectroscopic approaches. Moreover, very long cycling performance, that is, after even more than 3000 cycles the material still has a significant capacity of more than 800 mAh g^?1, is obtained by a simple electrode design involving introducing a rigid support into porous electrodes. Such long cycling performance is for the first time achieved for high‐capacity materials based on conversion reactions.     

High‐Performance Reversible Aqueous Zn‐Ion Battery Based on Porous MnOx Nanorods Coated by MOF‐Derived N‐Doped Carbon

Rechargeable aqueous zinc‐ion batteries (ZIBs) have been emerging as potential large‐scale energy storage devices due to their high energy density, low cost, high safety, and environmental friendliness. However, the commonly used cathode materials in ZIBs exhibit poor electrochemical performance, such as significant capacity fading during long‐term cycling and poor performance at high current rates, which significantly hinder the further development of ZIBs. Herein, a new and highly reversible Mn‐based cathode material with porous framework and N‐doping (MnO_x@N‐C) is prepared through a metal–organic framework template strategy. Benefiting from the unique porous structure, conductive carbon network, and the synergetic effect of Zn²⁺ and Mn²⁺ in electrolyte, the MnO_x@N‐C shows excellent cycling stability, good rate performance, and high reversibility for aqueous ZIBs. Specifically, it exhibits high capacity of 305 mAh g^?1 after 600 cycles at 500 mA g^?1 and maintains achievable capacity of 100 mAh g^?1 at a quite high rate of 2000 mA g^?1 with long‐term cycling of up to 1600 cycles, which are superior to most reported ZIB cathode materials. Furthermore, insight into the Zn‐storage mechanism in MnO_x@N‐C is systematically studied and discussed via multiple analytical methods. This study opens new opportunities for designing low‐cost and high‐performance rechargeable aqueous ZIBs.     

Boosting Superior Lithium Storage Performance of Alloy‐Based Anode Materials via Ultraconformal Sb Coating–Derived Favorable Solid‐Electrolyte Interphase

Alloy materials such as Si and Ge are attractive as high‐capacity anodes for rechargeable batteries, but such anodes undergo severe capacity degradation during discharge–charge processes. Compared to the over‐emphasized efforts on the electrode structure design to mitigate the volume changes, understanding and engineering of the solid‐electrolyte interphase (SEI) are significantly lacking. This work demonstrates that modifying the surface of alloy‐based anode materials by building an ultraconformal layer of Sb can significantly enhance their structural and interfacial stability during cycling. Combined experimental and theoretical studies consistently reveal that the ultraconformal Sb layer is dynamically converted to Li₃Sb during cycling, which can selectively adsorb and catalytically decompose electrolyte additives to form a robust, thin, and dense LiF‐dominated SEI, and simultaneously restrain the decomposition of electrolyte solvents. Hence, the Sb‐coated porous Ge electrode delivers much higher initial Coulombic efficiency of 85% and higher reversible capacity of 1046 mAh g^?1 after 200 cycles at 500 mA g^?1, compared to only 72% and 170 mAh g^?1 for bare porous Ge. The present finding has indicated that tailoring surface structures of electrode materials is an appealing approach to construct a robust SEI and achieve long‐term cycling stability for alloy‐based anode materials.     

Molecular Engineering of Monodisperse SnO2 Nanocrystals Anchored on Doped Graphene with High‐Performance Lithium/Sodium‐Storage Properties in Half/Full Cells

The fabrication of ultrasmall and high‐content SnO₂ nanocrystals anchored on doped graphene can endow SnO₂ with superior electrochemical properties. Herein, an effective strategy, involving molecular engineering of a layer‐by‐layer assembly technique, is proposed to homogeneously anchor SnO₂ nanocrystals on nitrogen/sulfur codoped graphene (NSGS), which serves as an advanced anode material in lithium/sodium‐ion batteries (LIBs/SIBs). Benefiting from novel design and specific structure, the optimized NSGS for LIBs displays high initial capacity (2123.9 mAh g^?1 at 0.1 A g^?1), long‐term cycling performance (only 0.8% loss after 500 cycles), and good rate capability (477.4 mAh g^?1 at 5 A g^?1). In addition, the optimized NSGS for SIBs also delivers high initial capacity (791.7 mAh g^?1 at 0.1 A g^?1) and high reversible capacity (180.2 mAh g^?1 after 500 cycles at 0.5 A g^?1). Meanwhile, based on the detailed analysis of phase transition and electrochemical reaction kinetics, the reaction mechanisms of NSGS in LIBs and SIBs as well as the distinction in LIBs/SIBs are clearly articulated. Notably, to further explore the practical application, Li/Na⁺ full cells are also assembled by coupling the optimized NSGS anode with LiCoO₂ and Na₃V₂(PO₄)₃/C cathodes, respectively.     

Partially Reduced Holey Graphene Oxide as High Performance Anode for Sodium‐Ion Batteries

The current Na⁺ storage performance of carbon‐based materials is still hindered by the sluggish Na⁺ ion transfer kinetics and low capacity. Graphene and its derivatives have been widely investigated as electrode materials in energy storage and conversion systems. However, as anode materials for sodium‐ion batteries (SIBs), the severe π–π restacking of graphene sheets usually results in compact structure with a small interlayer distance and a long ion transfer distance, thus leading to low capacity and poor rate capability. Herein, partially reduced holey graphene oxide is prepared by simple H₂O₂ treatment and subsequent low temperature reduction of graphene oxide, leading to large interlayer distance (0.434 nm), fast ion transport, and larger Na⁺ storage space. The partially remaining oxygenous groups can also contribute to the capacity by redox reaction. As anode material for SIBs, the optimized electrode delivers high reversible capacity, high rate capability (365 and 131 mAh g^?1 at 0.1 and 10 A g^?1, respectively), and good cycling performance (163 mAh g^?1 after 3000 cycles at a current density of 2 A g^?1), which is among the best reported performances for carbon‐based SIB anodes.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

A Low‐Cost Durable Na‐FeCl2 Battery with Ultrahigh Rate Capability

Na‐based batteries have long been regarded as an inexpensive, sustainable candidate for large‐scale stationary energy storage applications. Unfortunately, the market penetration of conventional Na‐NiCl₂ batteries is approaching its limit for several reasons, including limited rate capability and high Ni cost. Herein, a Na‐FeCl₂ battery operating at 190 °C is reported that allows a capacity output of 116 mAh g^?1 at an extremely high current density of 33.3 mA cm^?2 (≈0.6C). The superior rate performance is rooted in the intrinsically fast kinetics of the Fe/Fe²⁺ redox reaction. Furthermore, it is demonstrated that a small amount of Ni additive (10 mol%) effectively mitigates capacity fading of the Fe/NaCl cathode caused by Fe particle pulverization during long‐term cycling. The modified Fe/Ni cathode exhibits excellent cycling stability, maintaining a discharge energy density of over 295 Wh kg^?1 for 200 cycles at 10 mA cm^?2 (≈C/5).     

High Capacity Adsorption—Dominated Potassium and Sodium Ion Storage in Activated Crumpled Graphene

Structurally and chemically defective activated‐crumbled graphene (A‐CG) is employed to achieve unique synergy of large reversible potassium (K) and sodium (Na) ion storage capacity with fast charging and extended cyclability. A‐CG synthesis consists of low temperature spraying of graphene oxide slurry, followed by partial reduction annealing and air activation. For K storage, the reversible capacities are 340 mAh g^?1 at 0.04 A g^?1, 261 mAh g^?1 at 0.5 A g^?1, and 210 mAh g^?1 at 2 A g^?1. For Na storage, the reversible capacities are 280 mAh g^?1 at 0.04 A g^?1, 191 mAh g^?1 at 0.5 A g^?1, and 151 mAh g^?1 at 2 A g^?1. A‐CG shows a stable intermediate rate (0.5 Ag^?1) cycling with both K and Na, with minimal fade after 2800 and 8000 cycles. These are among the most favorable capacity—rate capability—cyclability combinations recorded for potassium‐ion battery and sodium‐ion battery carbons. Electroanalytical studies (cyclic voltammetry, galvanostatic intermittent titration technique, b‐value) and density functional theory (DFT) reveal that enhanced electrochemical performance originates from ion adsorption at various defects, such as Stone–Wales defects. Moreover, DFT highlights enhanced thermodynamic stability of A‐CG with adsorbed K versus with adsorbed Na, explaining the unexpected higher reversible capacity with the former.     

Intermixed Cation–Anion Aqueous Battery Based on an Extremely Fast and Long‐Cycling Di‐Block Bipyridinium–Naphthalene Diimide Oligomer

Aqueous batteries, particularly those integrating organic active materials functioning in a neutral pH environment, stand out as highly promising contenders in the stationary electrochemical storage domain, owing to their unparalleled safety, sustainability, and low‐cost materials. Herein, a novel di‐block oligomer, serving as the negative electrode of an all‐organic aqueous battery, is shown to offer exceptional output capabilities. The battery's performance is further enhanced by a unique intermixed p/n‐type storage mechanism, which is able to simultaneously exchange light and naturally abundant Na⁺, Mg²⁺, and Cl^?. Reaching up to 105 mAh g^?1, this system shows remarkable capacity retention for several thousand cycles (6500 cycles, ≈40 days) in various neutral electrolytes, including raw ocean water (≈3000 cycles, ≈75 days). The surprisingly fast kinetics of this di‐block oligomer allow to attain an unmatched specific capacity of near to 60 mAh g^?1_electrode while entirely devoid of conducting additives, and more than 80 mAh g^?1_electrode with 10% carbon additive, as well as displaying an areal capacity as high as 3.4 mAh cm^?2 at C rate. Full cell validation was demonstrated over 1600 cycles by virtue of a commercial 2,2,6,6‐tétraméthylpipéridin‐1‐yl)oxyl (TEMPO) molecule, which permitted an energy density of close to 40 Wh kg^?1_materials at C rate in a self‐pH‐buffered and inexpensive aqueous electrolyte.     

Confined Fe2VO4⊂Nitrogen‐Doped Carbon Nanowires with Internal Void Space for High‐Rate and Ultrastable Potassium‐Ion Storage

Developing low‐cost, high‐capacity, high‐rate, and robust earth‐abundant electrode materials for energy storage is critical for the practical and scalable application of advanced battery technologies. Herein, the first example of synthesizing 1D peapod‐like bimetallic Fe₂VO₄ nanorods confined in N‐doped carbon porous nanowires with internal void space (Fe₂VO₄?NC nanopeapods) as a high‐capacity and stable anode material for potassium‐ion batteries (KIBs) is reported. The peapod‐like Fe₂VO₄?NC nanopeapod heterostructures with interior void space and external carbon shell efficiently prevent the aggregation of the active materials, facilitate fast transportation of electrons and ions, and accommodate volume variation during the cycling process, which substantially boosts the rate and cycling performance of Fe₂VO₄. The Fe₂VO₄?NC electrode exhibits high reversible specific depotassiation capacity of 380 mAh g^?1 at 100 mA g^?1 after 60 cycles and remarkable rate capability as well as long cycling stability with a high capacity of 196 mAh g^?1 at 4 A g^?1 after 2300 cycles. The first‐principles calculations reveal that Fe₂VO₄?NC nanopeapods have high ionic/electronic conductivity characteristics and low diffusion barriers for K⁺‐intercalation. This study opens up new way for investigating high‐capacity metal oxide as high‐rate and robust electrode materials for KIBs.     

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Ni‐rich Li[Ni_xCo_yMn_1?x?y]O₂ (x ≥ 0.8) layered oxides are the most promising cathode materials for lithium‐ion batteries due to their high reversible capacity of over 200 mAh g^?1. Unfortunately, the anisotropic properties associated with the α‐NaFeO₂ structured crystal grains result in poor rate capability and insufficient cycle life. To address these issues, a micrometer‐sized Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ secondary cathode material consisting of radially aligned single‐crystal primary particles is proposed and synthesized. Concomitant with this unique crystallographic texture, all the exposed surfaces are active {010} facets, and 3D Li⁺ ion diffusion channels penetrate straightforwardly from surface to center, remarkably improving the Li⁺ diffusion coefficient. Moreover, coordinated charge–discharge volume change upon cycling is achieved by the consistent crystal orientation, significantly alleviating the volume‐change‐induced intergrain stress. Accordingly, this material delivers superior reversible capacity (203.4 mAh g^?1 at 3.0–4.3 V) and rate capability (152.7 mAh g^?1 at a current density of 1000 mA g^?1). Further, this structure demonstrates excellent cycling stability without any degradation after 300 cycles. The anisotropic morphology modulation provides a simple, efficient, and scalable way to boost the performance and applicability of Ni‐rich layered oxide cathode materials.     

Storage Capacity and Cycling Stability in Ge Anodes: Relationship of Anode Structure and Cycling Rate

Operando X‐ray diffraction (XRD) and X‐ray absorption spectroscopy (XAS) studies of Ge anodes are carried out to understand the effect of cycling rate on Ge phase transformation during charge/discharge process and to relate that effect to capacity. It is discovered that the formation of crystalline Li₁₅Ge₄ (c‐Li₁₅Ge₄) during lithiation is suppressed beyond a certain cycling rate. A very stable and reversible high capacity of ≈1800 mAh g^?1 can be attained up to 100 cycles at a slow C‐rate of C/21 when there is complete conversion of Ge anode into c‐Li₁₅Ge₄. When the C‐rate is increased to ≈C/10, the lithiation reaction is more heterogeneous and a relatively high capacity of ≈1000 mAh g^?1 is achieved with poorer electrochemical reversibility. An increase in C‐rate to C/5 and higher reduces the capacity (≈500 mAh g^?1) due to an impeded transformation from amorphous Li_xGe to c‐Li₁₅Ge₄, and yet improves the electrochemical reversibility. A proposed mechanism is presented to explain the C‐rate dependent phase transformations and the relationship of these to capacity fading. The operando XRD and XAS results provide new insights into the relationship between structural changes in Ge and battery capacity, which are important for guiding better design of high‐capacity anodes.     

A Novel α‐MoO3/Single‐Walled Carbon Nanohorns Composite as High‐Performance Anode Material for Fast‐Charging Lithium‐Ion Battery

Orthorhombic α‐MoO₃ is a potential anode material for lithium‐ion batteries due to its high theoretical capacity of 1100 mAh g^?1 and excellent structural stability. However, its intrinsic poor electronic conductivity and high volume expansion during the charge–discharge process impede it from achieving a high practical capacity. A novel composite of α‐MoO₃ nanobelts and single‐walled carbon nanohorns (SWCNHs) is synthesized by a facile microwave hydrothermal technique and demonstrated as a high‐performance anode material for lithium‐ion batteries. The α‐MoO₃/SWCNH composite displays superior electrochemical properties (654 mAh g^?1 at 1 C), excellent rate capability (275 mAh g^?1 at 5 C), and outstanding cycle life (capacity retention of >99% after 3000 cycles at 1 C) without any cracking of the electrode. The presence of SWCNHs in the composite enhances the electrochemical properties of α‐MoO₃ by acting as a lithium storage material, electronic conductive medium, and buffer against pulverization.     

Controlled Oxygen Redox for Excellent Power Capability in Layered Sodium‐Based Compounds

A high‐rate of oxygen redox assisted by cobalt in layered sodium‐based compounds is achieved. The rationally designed Na_0.6[Mg_0.2Mn_0.6Co_0.2]O₂ exhibits outstanding electrode performance, delivering a discharge capacity of 214 mAh g^?1 (26 mA g^?1) with capacity retention of 87% after 100 cycles. High rate performance is also achieved at 7C (1.82 A g^?1) with a capacity of 107 mAh g^?1. Surprisingly, the Na_0.6[Mg_0.2Mn_0.6Co_0.2]O₂ compound is able to deliver capacity for 1000 cycles at 5C (at 1.3 A g^?1), retaining 72% of its initial capacity of 108 mAh g^?1. X‐ray absorption spectroscopy analysis of the O K‐edge indicates the oxygen‐redox species (O^2?/1?) is active during cycling. First‐principles calculations show that the addition of Co reduces the bandgap energy from ≈2.65 to ≈0.61 eV and that overlapping of the Co 3d and O 2p orbitals facilitates facile electron transfer, enabling the long‐term reversibility of the oxygen redox, even at high rates. To the best of the authors' knowledge, this is the first report on high‐rate oxygen redox in sodium‐based cathode materials, and it is believed that the findings will open a new pathway for the use of oxygen‐redox‐based materials for sodium‐ion batteries.     

New Class of Ni‐Rich Cathode Materials Li[NixCoyB1−x−y]O2 for Next Lithium Batteries

A new class of layered cathodes, Li[Ni_xCo_yB_1?x?y]O₂ (NCB), is synthesized. The proposed NCB cathodes have a unique microstructure in which elongated primary particles are tightly packed into spherical secondary particles. The cathodes also exhibit a strong crystallographic texture in which the a–b layer planes are aligned along the radial direction, facilitating Li migration. The microstructure, which effectively suppresses the formation of microcracks, improves the cycling stability of the NCB cathodes. The NCB cathode with 1.5 mol% B delivers a discharge capacity of 234 mAh g^?1 at 0.1 C and retains 91.2% of its initial capacity after 100 cycles (compared to values of 229 mAh g^?1 at 0.1 C and 78.8% for pristine Li[Ni_0.9Co_0.1]O₂). This study shows the importance of controlling the microstructure to obtain the required cycling stability, especially for Ni‐rich layered cathodes, where the main cause of capacity fading is related to mechanical strain in their charged state.     

A Flexible Porous Carbon Nanofibers‐Selenium Cathode with Superior Electrochemical Performance for Both Li‐Se and Na‐Se Batteries

A flexible and free‐standing porous carbon nanofibers/selenium composite electrode (Se@PCNFs) is prepared by infiltrating Se into mesoporous carbon nanofibers (PCNFs). The porous carbon with optimized mesopores for accommodating Se can synergistically suppress the active material dissolution and provide mechanical stability needed for the film. The Se@PCNFs electrode exhibits exceptional electrochemical performance for both Li‐ion and Na‐ion storage. In the case of Li‐ion storage, it delivers a reversible capacity of 516 mAh g^?1 after 900 cycles without any capacity loss at 0.5 A g^?1. Se@PCNFs still delivers a reversible capacity of 306 mAh g^?1 at 4 A g^?1. While being used in Na‐Se batteries, the composite electrode maintains a reversible capacity of 520 mAh g^?1 after 80 cycles at 0.05 A g^?1 and a rate capability of 230 mAh g^?1 at 1 A g^?1. The high capacity, good cyclability, and rate capability are attributed to synergistic effects of the uniform distribution of Se in PCNFs and the 3D interconnected PCNFs framework, which could alleviate the shuttle reaction of polyselenides intermediates during cycling and maintain the perfect electrical conductivity throughout the electrode. By rational and delicate design, this type of self‐supported electrodes may hold great promise for the development of Li‐Se and Na‐Se batteries with high power and energy densities.     

One‐Step Synthesis of 2‐Ethylhexylamine Pillared Vanadium Disulfide Nanoflowers with Ultralarge Interlayer Spacing for High‐Performance Magnesium Storage

Rechargeable magnesium batteries (RMBs) are attractive candidates for large‐scale energy storage owing to the high theoretical specific capacity, rich earth abundance, and good safety characteristics. However, the development of desirable cathode materials for RMBs is constrained by the high polarity and slow intercalation kinetics of Mg²⁺ ions. Herein, it is demonstrated that 2‐ethylhexylamine pillared vanadium disulfide nanoflowers (expanded VS₂) with enlarged interlayer distances exhibit greatly boosted electrochemical performance as a cathode material in RMBs. Through a one‐step solution‐phase synthesis and in situ 2‐ethylhexylamine intercalation process, VS₂ nanoflowers with ultralarge interlayer spacing are prepared. A series of ex situ characterizations verify that the cathode of expanded VS₂ nanoflowers undergoes a reversible intercalation reaction mechanism, followed by a conversion reaction mechanism. Electrochemical kinetics analysis reveal a relatively fast Mg‐ion diffusivity of expanded VS₂ nanoflowers in the order of 10^?11–10^?12 cm² s^?1, and the pseudocapacitive contribution is up to 64% for the total capacity at 1 mV s^?1. The expanded VS₂ nanoflowers show highly reversible discharge capacity (245 mAh g^?1 at 100 mA g^?1), good rate capability (103 mAh g^?1 at 2000 mA g^?1), and stable cycling performance (90 mAh g^?1 after 600 cycles at 1000 mA g^?1).     

Stress‐Relieved Nanowires by Silicon Substitution for High‐Capacity and Stable Lithium Storage

Silicon is promising as a high energy anode for next‐generation lithium‐ion batteries. However, severe capacity fading upon cycling associated with huge volume change is still an obstacle for silicon toward practical applications. Herein, the authors report that Si‐substituted Zn₂(GeO₄)_0.8(SiO₄)_0.2 nanowires can effectively suppress volume expansion effect, exhibiting high specific capacity (1274 mA h g^?1 at 0.2 A g^?1 after 700 cycles) and ultralong cycling stability (2000 cycles at 5 A g^?1 with a capacity decay rate of 0.008% per cycle), which represents outstanding comprehensive performance. The superior performance is ascribed to the substitution of Si atom that imparts to the nanowires not only high reactivity and reversibility, but also the unique stress‐relieved property upon lithiation which is further confirmed by detailed density‐functional theory computation. This work provides a new guideline for designing high‐performance Si‐based materials toward practical energy storage applications.