Superb Alkaline Hydrogen Evolution and Simultaneous Electricity Generation by Pt‐Decorated Ni3N Nanosheets

The development of efficient hydrogen evolution reaction electrocatalysts is critical to the realization of clean hydrogen fuel production, while the sluggish kinetics of the Volmer‐step substantially restricts the catalyst performances in alkali electrolyzers, even for noble metal catalysts such as Pt. Here, a Pt‐decorated Ni₃N nanosheet electrocatalyst is developed to achieve a top performance of hydrogen evolution in alkaline conditions. Possessing a high metallic conductivity and an atomic‐thin semiconducting hydroxide surface, the Ni₃N nanosheets serve as not only an efficient electron pathway without the hindrance of Schottky barriers, but also provide abundant active sites for water dissociation and generation of hydrogen intermediates, which are further adsorbed on the Pt surface to recombine to H₂. The Pt‐decorated Ni₃N nanosheet catalyst exhibits a hydrogen evolution current density of 200 mA cm^?2 at an overpotential of 160 mV versus reversible hydrogen electrode, a Tafel slope of ≈36.5 mV dec^?1, and excellent stability of 82.5% current retention after 24 h of operation. Moreover, a hybrid cell consisting of a Pt‐decorated Ni₃N nanosheet cathode and a Li‐metal anode is assembled to achieve simultaneous hydrogen evolution and electricity generation, exhibiting >60 h long‐term hydrogen evolution reaction stability and an output voltage ranging from 1.3 to 2.2 V.     

Theoretical and Experimental Insight into the Effect of Nitrogen Doping on Hydrogen Evolution Activity of Ni3S2 in Alkaline Medium

Nickel sulfide (Ni₃S₂) is a promising hydrogen evolution reaction (HER) catalyst by virtue of its metallic electrical conductivity and excellent stability in alkaline medium. However, the reported catalytic activities for Ni₃S₂ are still relatively low. Herein, an effective strategy to boost the H adsorption capability and HER performance of Ni₃S₂ through nitrogen (N) doping is demonstrated. N‐doped Ni₃S₂ nanosheets achieve a fairly low overpotential of 155 mV at 10 mA cm^?2 and an excellent exchange current density of 0.42 mA cm^?2 in 1.0 m KOH electrolyte. The mass activity of 16.9 mA mg^?1 and turnover frequency of 2.4 s^?1 obtained at 155 mV are significantly higher than the values reported for other Ni₃S₂‐based HER catalysts, and comparable to the performance of best HER catalysts in alkaline medium. These experimental data together with theoretical analysis suggest that the outstanding catalytic activity of N‐doped Ni₃S₂ is due to the enriched active sites with favorable H adsorption free energy. The activity in the Ni₃S₂ is highly correlated with the coordination number of the surface S atoms and the charge depletion of neighbor Ni atoms. These new findings provide important guidance for future experimental design and synthesis of optimal HER catalysts.     

A Dual‐Insertion Type Sodium‐Ion Full Cell Based on High‐Quality Ternary‐Metal Prussian Blue Analogs

Prussian blue analogs (PBAs) are especially investigated as superior cathodes for sodium‐ion batteries (SIBs) due to high theoretical capacity (≈170 mA h g^?1) with 2‐Na storage and low cost. However, PBAs suffer poor cyclability due to irreversible phase transition in deep charge/discharge states. PBAs also suffer low crystallinity, with considerable [Fe(CN)₆] vacancies, and coordinated water in crystal frameworks. Presently, a new chelating agent/surfactant coassisted crystallization method is developed to prepare high‐quality (HQ) ternary‐metal Ni_xCo_1?x[Fe(CN)₆] PBAs. By introducing inactive metal Ni to suppress capacity fading caused by excessive lattice distortion, these PBAs have tunable limits on depth of charge/discharge. HQ‐Ni_xCo_1?x[Fe(CN)₆] (x = 0.3) demonstrates the best reversible Na‐storage behavior with a specific capacity of ≈145 mA h g^?1 and a remarkably improved cycle performance, with ≈90% capacity retention over 600 cycles at 5 C. Furthermore, a dual‐insertion full cell on the cathode and NaTi₂(PO₄)₃ anode delivers reversible capacity of ≈110 mA h g^?1 at a current rate of 1.0 C without capacity fading over 300 cycles, showing promise as a high‐performance SIB for large‐scale energy‐storage systems. The ultrastable cyclability achieved in the lab and explained herein is far beyond that of any previously reported PBA‐based full cells.     

Mn‐Rich P′2‐Na0.67[Ni0.1Fe0.1Mn0.8]O2 as High‐Energy‐Density and Long‐Life Cathode Material for Sodium‐Ion Batteries

Herein, P′2‐type Na_0.67[Ni_0.1Fe_0.1Mn_0.8]O₂ is introduced as a promising new cathode material for sodium‐ion batteries (SIBs) that exhibits remarkable structural stability during repetitive Na⁺ de/intercalation. The O? Ni? O? Mn? O? Fe? O bond in the octahedra of transition‐metal layers is used to suppress the elongation of the Mn? O bond and to improve the electrochemical activity, leading to the highly reversible Na storage mechanism. A high discharge capacity of ≈220 mAh g^?1 (≈605 Wh kg^?1) is delivered at 0.05 C (13 mAg^?1) with a high reversible capacity of ≈140 mAh g^?1 at 3 C and excellent capacity retention of 80% over 200 cycles. This performance is associated with the reversible P′2–OP4 phase transition and small volume change upon charge and discharge (≈3%). The nature of the sodium storage mechanism in a full cell paired with a hard carbon anode reveals an unexpectedly high energy density of ≈542 Wh kg^?1 at 0.2 C and good capacity retention of ≈81% for 500 cycles at 1 C (260 mAg^?1).     

Bimetallic Zeolitic Imidazolite Framework Derived Carbon Nanotubes Embedded with Co Nanoparticles for Efficient Bifunctional Oxygen Electrocatalyst

Bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with high activities and low‐cost are of prime importance and challenging in the development of fuel cells and rechargeable metal–air batteries. This study reports a porous carbon nanomaterial loaded with cobalt nanoparticles (Co@NC‐x/y) derived from pyrolysis of a Co/Zn bimetallic zeolitic imidazolite framework, which exhibits incredibly high activity as bifunctional oxygen catalysts. For instance, the optimal catalyst of Co@NC‐3/1 has the interconnected framework structure between porous carbon and embedded carbon nanotubes, which shows the superb ORR activity with onset potential of ≈1.15 V and half‐wave potential of ≈0.93 V. Moreover, it presents high OER activity that can be further enhanced to over commercial RuO₂ by P‐doped with overpotentials of 1.57 V versus reversible hydrogen electrode at 10 mA cm^?2 and long‐term stability for 2000 circles and a Tafel slope of 85 mV dec^?1. Significantly, the nanomaterial demonstrates better catalytic performance and durability than Pt/C for ORR and commercial RuO₂ and IrO₂ for OER. These findings suggest the importance of a synergistic effect of graphitic carbon, nanotubes, exposed Co–N_x active sites, and interconnected framework structure of various carbons for bifunctional oxygen electrocatalysts.     

A New P2‐Type Layered Oxide Cathode with Extremely High Energy Density for Sodium‐Ion Batteries

Herein, a new P2‐type layered oxide is proposed as an outstanding intercalation cathode material for high energy density sodium‐ion batteries (SIBs). On the basis of the stoichiometry of sodium and transition metals, the P2‐type Na_0.55[Ni_0.1Fe_0.1Mn_0.8]O₂ cathode is synthesized without impurities phase by partially substituting Ni and Fe into the Mn sites. The partial substitution results in a smoothing of the electrochemical charge/discharge profiles and thus greatly improves the battery performance. The P2‐type Na_0.55[Ni_0.1Fe_0.1Mn_0.8]O₂ cathode delivers an extremely high discharge capacity of 221.5 mAh g^?1 with a high average potential of ≈2.9 V (vs Na/Na⁺) for SIBs. In addition, the fast Na‐ion transport in the P2‐type Na_0.55[Ni_0.1Fe_0.1Mn_0.8]O₂ cathode structure enables good power capability with an extremely high current density of 2400 mA g^?1 (full charge/discharge in 12 min) and long‐term cycling stability with ≈80% capacity retention after 500 cycles at 600 mA g^?1. A combination of electrochemical profiles, in operando synchrotron X‐ray diffraction analysis, and first‐principles calculations are used to understand the overall Na storage mechanism of P2‐type Na_0.55[Ni_0.1Fe_0.1Mn_0.8]O₂.     

P2‐K0.75[Ni1/3Mn2/3]O2 Cathode Material for High Power and Long Life Potassium‐Ion Batteries

Rationally designed P2‐K_0.75[Ni_1/3Mn_2/3]O₂ is introduced as a novel cathode material for potassium‐ion batteries (KIBs). P2‐K_0.75[Ni_1/3Mn_2/3]O₂ cathode material designed through electrochemical ion‐exchange from P2‐Na_2/3[Ni_1/3Mn_2/3]O₂ exhibits satisfactory electrode performances; 110 mAh g^?1 (20 mA g^?1) retaining 86% of capacity for 300 cycles and unexpectedly high reversible capacity of about 91 mAh g^?1 (1400 mA g^?1) with excellent capacity retention of 83% over 500 cycles. According to theoretical and experimental investigations, the overall potassium storage mechanism of P2‐K_0.75[Ni_1/3Mn_2/3]O₂ is revealed to be a single‐phase reaction with small lattice change upon charge and discharge, presenting the Ni^4+/2+ redox couple reaction. Such high power capability is possible through the facile K⁺ migration in the K_0.75[Ni_1/3Mn_2/3]O₂ structure with a low activation barrier energy of ≈210 meV. These findings indicate that P2‐K_0.75[Ni_1/3Mn_2/3]O₂ is a promising candidate cathode material for high‐rate and long‐life KIBs.     

Multiphase Nanostructure of a Quinary Metal Oxide Electrocatalyst Reveals a New Direction for OER Electrocatalyst Design

Ce‐rich mixed metal oxides comprise a recently discovered class of ­electrocatalysts for the oxygen evolution reaction (OER). In particular, at current densities below 10 mA cm^?2, Ni_0.3Fe_0.07Co_0.2Ce_0.43O_x exhibits ­superior activity compared to the corresponding transition metal oxides, despite the relative inactivity of ceria. To elucidate the enhanced activity and underlying catalytic mechanism, detailed structural characterization of this quinary oxide electrocatalyst is reported. Transmission electron microscopy imaging of cross‐section films as‐prepared and after electrochemical testing reveals a stable two‐phase nanostructure composed of 3–5 nm diameter crystallites of fluorite CeO₂ intimately mixed with 3–5 nm crystallites of transition metal oxides alloyed in the rock salt NiO structure. Dosing experiments demonstrate that an electron flux greater than ≈1000 e Å^?2 s^?1 causes the inherently crystalline material to become amorphous. A very low dose rate of 130 e Å^?2 s^?1 is employed for atomic resolution imaging using inline holography techniques to reveal a nanostructure in which the transition metal oxide nanocrystals form atomically sharp boundaries with the ceria nanocrystals, and these results are corroborated with extensive synchrotron X‐ray absorption spectroscopy measurements. Ceria is a well‐studied cocatalyst for other heterogeneous and electrochemical reactions, and our discovery introduces biphasic cocatalysis as a design concept for improved OER electrocatalysts.     

Complete Dehydrogenation of N2H4BH3 over Noble‐Metal‐Free Ni0.5Fe0.5–CeOx/MIL‐101 with High Activity and 100% H2 Selectivity

Efficient and selective dehydrogenation of hydrazine borane (HB), a novel hydrogen storage material with very high hydrogen content (HB, 15.4 wt%), is a key challenge for a fuel‐cell‐based hydrogen economy. However, even using the noble metal catalysts for HB decomposition, the activities are still far from satisfying, to say nothing of non‐noble‐metal‐containing catalysts. In response, as a proof‐of‐concept experiment, herein, noble‐metal‐free NiFe–CeO_x nanoparticles are successfully immobilized on an MIL‐101 support without surfactant by a simple liquid impregnation method. Unexpectedly, the resultant Ni_0.5Fe_0.5–CeO_x/MIL‐101 catalyst shows good performance, including 100% H₂ selectivity, 100% conversion, and record catalytic activity (351.3 h^?1) for hydrogen generation at mild temperature, which is even better than most of the noble metal heterogeneous catalysts and might be attributed to the good dispersion and uniform particle size of the Ni_0.5Fe_0.5–CeO_x nanoparticles due to steric restrictions effect of the MIL‐101 support. Additionally, extending MIL‐101 to some other important kinds of metal–organic framework (MOF) structures, the resultant NiFe–CeO_x/MOF catalysts all show good catalytic activity toward HB decomposition, showing the universality of the MOF supported NiFe–CeO_x catalysts.     

Nitrogen and Sulfur Vacancies in Carbon Shell to Tune Charge Distribution of Co6Ni3S8 Core and Boost Sodium Storage

Recently, the metal sulfide‐carbon nanocomposites have been suggested as a low‐cost alternative to lithium ion batteries, but commercial application is seriously hindered by their relatively inferior cyclic performance. Herein, N and S vacancies in an N,S co‐doped carbon (NSC) shell for anchoring a new bimetallic sulfide core of Co₆Ni₃S₈ using Co‐Ni‐alginate biomass are introduced. The obtained Co₆Ni₃S₈/carbon aerogels (Co₆Ni₃S₈/NSCA) exhibit excellent sodium‐ion storage properties, high reversible capacity (568.1 mAh g^?1 at 1 A g^?1), and an excellent cycle stability (94.4% after 300 cycles). Density functional theory calculation results disclose that nitrogen and sulfur vacancies in the carbon shell can enhance the binding between the Co₆Ni₃S₈ core and NSC shell, ensuring an improved structural and electrochemical stability. In addition, an increased adsorption energy of Na⁺ (?1.88 eV) and a decreased barrier energy for Na⁺ diffusion (0.46 eV) are observed indicating a fast Na⁺ diffusion process. The powder X‐ray diffraction refinement confirms that the lattice parameters of Co₆Ni₃S₈ extend to 0.9972 nm compared with Co₉S₈ (0.9928 nm), suppressing the volume expansion in Na⁺ diffusion processes.     

Ni3Fe‐N Doped Carbon Sheets as a Bifunctional Electrocatalyst for Air Cathodes

A promising bifunctional electrocatalyst is reported for air cathodes consisting of Ni₃Fe nanoparticles embedded in porous nitrogen‐doped carbon sheets (Ni₃Fe/N‐C sheets) by a facile and effective pyrolysis‐based route with sodium chloride (NaCl) crystals as a template. The Ni₃Fe/N‐C sheets show excellent catalytic activity, selectivity, and durability toward both the oxygen‐reduction and oxygen‐evolution reactions (ORR and OER). They are shown to provide a superior, low‐cost cathode for a rechargeable Zn‐air battery. At a discharge–charge current density of 10 mA cm^?2, the Ni₃Fe/N‐C sheets enable a Zn–air battery to cycle steadily up to 420 h with only a small increase in the round‐trip overpotential, outperforming the more costly Pt/C + IrO₂ mixture catalyst (160 h). With the simplicity and scalability of the synthetic approach and its remarkable bifunctional electrocatalytic performance, the Ni₃Fe/N‐C sheets offer a promising rechargeable air cathode operating at room temperature in an alkaline electrolyte.     

Interface Engineering of Hierarchical Branched Mo‐Doped Ni3S2/NixPy Hollow Heterostructure Nanorods for Efficient Overall Water Splitting

Rational design and construction of bifunctional electrocatalysts with excellent activity and durability is imperative for water splitting. Herein, a novel top‐down strategy to realize a hierarchical branched Mo‐doped sulfide/phosphide heterostructure (Mo‐Ni₃S₂/Ni_xP_y hollow nanorods), by partially phosphating Mo‐Ni₃S₂/NF flower clusters, is proposed. Benefitting from the optimized electronic structure configuration, hierarchical branched hollow nanorod structure, and abundant heterogeneous interfaces, the as‐obtained multisite Mo‐Ni₃S₂/Ni_xP_y/NF electrode has remarkable stability and bifunctional electrocatalytic activity in the hydrogen evolution reaction (HER)/oxygen evolution reaction (OER) in 1 m KOH solutions. It possesses an extremely low overpotential of 238 mV at the current density of 50 mA cm^?2 for OER. Importantly, when assembled as anode and cathode simultaneously, it merely requires an ultralow cell voltage of 1.46 V to achieve the current density of 10 mA cm^?2, with excellent durability for over 72 h, outperforming most of the reported Ni‐based bifunctional materials. Density functional theory results further confirm that the doped heterostructure can synergistically optimize Gibbs free energies of H and O‐containing intermediates (OH*, O*, and OOH*) during HER and OER processes, thus accelerating the catalytic kinetics of electrochemical water splitting. This work demonstrates the importance of the rational combination of metal doping and interface engineering for advanced catalytic materials.     

One-step hydrogenation-esterification of furfural and acetic acid over bifunctional Pd catalysts for bio-oil upgrading

This contribution focuses on one-step hydrogenation-esterification (OHE) of furfural and acetic acid, which are difficult to treat and typically present in crude bio-oil, as a model reaction for bio-oil upgrading. A bifunctional catalyst is needed for OHE reaction. Among tested bifunctional catalysts, the 5%Pd/Al₂(SiO₃)₃ shows the best catalytic performance. Compared to the physical mixture of 5%Pd/C + Al₂(SiO₃)₃, there is a synergistic effect between metal sites and acid sites over 5%Pd/Al₂(SiO₃)₃ for the OHE reaction. A moderate reaction condition would be required to obtain high yields of alcohol and ester along with lower byproduct yields. In this work, the optimum selectivity to desired products (alcohol and ester) of 66.4% is obtained, where the conversion of furfural is 56.9%. Other components, typically present in bio-oils, have little effects on the OHE of FAL and HAc. This OHE method is a promising route for efficient upgrading of bio-oil.     

Identifying Catalytic Active Sites of Trimolybdenum Phosphide (Mo3P) for Electrochemical Hydrogen Evolution

Solid‐state electrocatalysis plays a crucial role in the development of renewable energy to reshape current and future energy needs. However, finding an inexpensive and highly active catalyst to replace precious metals remains a big challenge for this technology. Here, tri‐molybdenum phosphide (Mo₃P) is found as a promising nonprecious metal and earth‐abundant candidate with outstanding catalytic properties that can be used for electrocatalytic processes. The catalytic performance of Mo₃P nanoparticles is tested in the hydrogen evolution reaction (HER). The results indicate an onset potential of as low as 21 mV, H₂ formation rate, and exchange current density of 214.7 µmol s^?1 g^?1_cat (at only 100 mV overpotential) and 279.07 µA cm^?2, respectively, which are among the closest values yet observed to platinum. Combined atomic‐scale characterizations and computational studies confirm that high density of molybdenum (Mo) active sites at the surface with superior intrinsic electronic properties are mainly responsible for the remarkable HER performance. The density functional theory calculation results also confirm that the exceptional performance of Mo₃P is due to neutral Gibbs free energy (ΔG_H*) of the hydrogen (H) adsorption at above 1/2 monolayer (ML) coverage of the (110) surface, exceeding the performance of existing non‐noble metal catalysts for HER.     

In Situ,Fast, High‐Temperature Synthesis of Nickel Nanoparticles in Reduced Graphene Oxide Matrix

For the first time, a fast heating–cooling process is reported for the synthesis of carbon‐coated nickel (Ni) nanoparticles on a reduced graphene oxide (RGO) matrix (nano‐Ni@C/RGO) as a high‐performance H₂O₂ fuel catalyst. The Joule heating temperature can reach up to ≈2400 K and the heating time can be less than 0.1 s. Ni microparticles with an average diameter of 2 µm can be directly converted into nanoparticles with an average diameter of 75 nm. The Ni nanoparticles embedded in RGO are evaluated for electro‐oxidation performance as a H₂O₂ fuel in a direct peroxide–peroxide fuel cell, which exhibits an electro‐oxidation current density of 602 mA cm^?2 at 0.2 V (vs Ag/AgCl), ≈150 times higher than the original Ni microparticles embedded in the RGO matrix (micro‐Ni/RGO). The high‐temperature, fast Joule heating process also leads to a 4–5 nm conformal carbon coating on the surface of the Ni nanoparticles, which anchors them to the RGO nanosheets and leads to an excellent catalytic stability. The newly developed nano‐Ni@C/RGO composites by Joule heating hold great promise for a range of emerging energy applications, including the advanced anode materials of fuel cells.     

Phase Boundary Derived Pseudocapacitance Enhanced Nickel‐Based Composites for Electrochemical Energy Storage Devices

Several strategies have been employed to improve the performance of energy storage devices through the development of new electrode materials. The construction of transition metal compound composite electrodes plays an important role in promoting the performance of energy storage devices. However, understandings of and insight into how to enhance the composites properties are rarely reported. Taking nickel‐based compounds as an example, Ni₃N@Ni₃S₂ hybrid nanosheets are reported as a high‐performance anode material for lithium‐ion batteries that delivers higher lithium storage properties than the pristine Ni₃N and Ni₃S₂ electrodes. This demonstrates that the phase boundaries between the Ni₃N and Ni₃S₂ may contribute additional lithium storage, which leads to a synergistic effect via the high pseudocapacitance contribution from the outstanding conductivity of Ni₃N and enhanced diffusion‐controlled capacity of Ni₃S₂. The use of composites prepared through sulfuration of hydrothermally annealed nickel hydroxide‐based precursor provides an enhancement of the energy storage properties. These results provide an important approach for increasing the electrochemical activity of composites by the combined effect of interfacial mismatch and pseudocapacitance, as well as understandings of the mechanism of the enhancement of the composite electrode properties.     

Hierarchical Fabric Decorated with Carbon Nanowire/Metal Oxide Nanocomposites for 1.6 V Wearable Aqueous Supercapacitors

Aqueous asymmetric supercapacitors (ASCs) may offer comparable or higher energy density than electric double‐layer capacitors (EDLCs) based on organic electrolytes. As such, ASCs may be more suitable for integration into smart textiles, where the use of flammable organic solvents is not acceptable. However, reported ASC devices typically suffer from poor rate capability and low areal loadings. This study demonstrates the development of nitrogen‐doped carbon (N‐C) nanowire/metal oxide (Fe₂O₃ and MnO₂) nanocomposite electrodes directly produced on the internal surface of a conductive fabric for use as high‐rate electrodes for solid‐state ASCs. The N‐C nanowires provide fast and efficient pathways for electrons, while short diffusion paths within nanosized metal oxides enable fast ion transport, leading to greatly enhanced performance at high rates. The porous structure of the fabric enables high areal capacitance loading in each electrode (≈150 mF cm^?2). Both electrodes show high specific capacitance of ≈180 F g^?1 (Fe₂O₃) and ≈250 F g^?1 (MnO₂) and excellent rate capability. Solid‐state ASCs assembled by using an aqueous gel electrolyte operate at 1.6 V and deliver over 60 mF cm^?2 during ≈50 s charging/discharging time and over 30 mF cm^?2 for ≈5 s discharge.     

A Simple Synthetic Strategy toward Defect‐Rich Porous Monolayer NiFe‐Layered Double Hydroxide Nanosheets for Efficient Electrocatalytic Water Oxidation

In this work, porous monolayer nickel‐iron layered double hydroxide (PM‐LDH) nanosheets with a lateral size of ≈30 nm and a thickness of ≈0.8 nm are successfully synthesized by a facile one‐step strategy. Briefly, an aqueous solution containing Ni²⁺ and Fe³⁺ is added dropwise to an aqueous formamide solution at 80 °C and pH 10, with the PM‐LDH product formed within only 10 min. This fast synthetic strategy introduces an abundance of pores in the monolayer NiFe‐LDH nanosheets, resulting in PM‐LDH containing high concentration of oxygen and cation vacancies, as is confirmed by extended X‐ray absorption fine structure and electron spin resonance measurements. The oxygen and cation vacancies in PM‐LDH act synergistically to increase the electropositivity of the LDH nanosheets, while also enhancing H₂O adsorption and bonding strength of the OH* intermediate formed during water electrooxidation, endowing PM‐LDH with outstanding performance for the oxygen evolution reaction (OER). PM‐LDH offers a very low overpotential (230 mV) for OER at a current density of 10 mA cm^?2, with a Tafel slope of only 47 mV dec^?1, representing one of the best OER performance yet reported for a NiFe‐LDH system. The results encourage the wider utilization of porous monolayer LDH nanosheets in electrocatalysis, catalysis, and solar cells.     

Phase Transformation Induced Capacitance Activation for 3D Graphene‐CoO Nanorod Pseudocapacitor

Development of a pseudocapacitor over the integration of metal oxide on carbonaceous materials is a promising step towards energy storage devices with high energy and power densities. Here, a self‐assembled cobalt oxide (CoO) nanorod cluster on three‐dimensional graphene (CoO‐3DG) is synthesized through a facile hydrothermal method followed by heat treatment. As an additive‐free electrode, CoO‐3DG exhibits good electrochemical performance. Compared with CoO nanorod clusters grown on Ni foam (i.e., CoO‐Ni, ≈680 F g^?1 at 1 A g^?1 and ≈400 F g^?1 at 20 A g^?1), CoO‐3DG achieves much higher capacitance (i.e., ≈980 F g^?1 at 1 A g^?1 and ≈600 F g^?1 at 20 A g^?1) with excellent cycling stability of 103% retention of specific capacitance after 10 000 cycles. Furthermore, it shows an interesting activation process and instability with a redox reaction for CoO. In addition, the phase transformation from CoO nanorods to Co₃O₄ nanostructures was observed and investigated after charge and discharge process, which suggests the activation kinetics and the phase transformable nature of CoO based nanostructure. These observations demonstrate phase transformation with morphological change induced capacitance increasement in the emergent class of metal oxide materials for electrochemical energy storage device.     

Ni3+‐Induced Formation of Active NiOOH on the Spinel Ni–Co Oxide Surface for Efficient Oxygen Evolution Reaction

Efficient and earth abundant electrocatalysts for high‐performance oxygen evolution reaction (OER) are essential for the development of sustainable energy conversion technologies. Here, a new hierarchical Ni–Co oxide nanostructure, composed of small secondary nanosheets grown on primary nanosheet arrays, is synthesized via a topotactic transformation of Ni–Co layered double hydroxide. The Ni³⁺‐rich surface benefits the formation of NiOOH, which is the main redox site as revealed via in situ X‐ray absorption near edge structure and extended X‐ray absorption fine structure spectroscopy. The Ni–Co oxide hierarchical nanosheets (NCO–HNSs) deliver a stable current density of 10 mA cm^?2 at an overpotential of ≈0.34 V for OER with a Tafel slope of as low as 51 mV dec^?1 in alkaline media. The improvement in the OER activity can be ascribed to the synergy of large surface area offered by the 3D hierarchical nanostructure and the facile formation of NiOOH as the main active sites on the surface of NCO–HNSs to decrease the overpotential and facilitate the catalytic reaction.