Preparation and properties of an immobilized pectinlyase for the treatment of fruit juices

Pectinlyase, present in different commercial pectinases used in juice technology, was immobilized on alginate beads. The optimal conditions were: 0.17 g alginate ml(-1), 1.2% (w/v or v/v) enzyme concentration and acetic-HCl/glycine-HCl buffer at pH 3.6 or tris-HCl/imidazole buffer at pH 6.4. Maximum percentage of immobilization (10.6%) was obtained with Rapidase C80. Kinetic parameters of free and immobilized pectinlyase were also determined. The pH and temperature at which activity of soluble and immobilized enzyme was maximum were 7.2 and 55 degrees C. Thermal stability was not significantly altered by immobilization, especially at 40 degrees C, showing two periods of different stability. Free and immobilized preparation reduced the viscosity of highly esterified pectin from 1.09 to 0.70 and 0.72 mm(2) s(-1), respectively, after 30 min at 40 degrees C. Furthermore, the immobilized enzyme could be re-used through 4 cycles and the efficiency loss in viscosity reduction was found to be only 9.2%.     

Immobilization of beta-galactosidase on fibrous matrix by polyethyleneimine for production of galacto-oligosaccharides from lactose

The production of galacto-oligosaccharides (GOS) from lactose by Aspergillus oryzae beta-galactosidase immobilized on cotton cloth was studied. A novel method of enzyme immobilization involving PEI-enzyme aggregate formation and growth of aggregates on individual fibrils of cotton cloth leading to multilayer immobilization of the enzyme was developed. A large amount of enzyme was immobilized (250 mg/g support) with about 90-95% efficiency. A maximum GOS production of 25-26% (w/w) was achieved at near 50% lactose conversion from 400 g/L of lactose at pH 4.5 and 40 degrees C. Tri- and tetrasaccharides were the major types of GOS formed, accounting for about 70% and 25% of the total GOS produced in the reactions, respectively. Temperature and pH affected not only the reaction rate but also GOS yield to some extend. A reaction pH of 6.0 increased GOS yield by as much as 10% compared with that of pH 4.5 while decreased the reaction rate of immobilized enzyme. The cotton cloth as the support matrix for enzyme immobilization did not affect the GOS formation characteristics of the enzyme under the same reaction conditions, suggesting diffusion limitation was negligible in the packed bed reactor and the enzyme carrier. Increase in the thermal stability of PEI-immobilized enzyme was also observed. The half-life for the immobilized enzyme on cotton cloth was close to 1 year at 40 degrees C and 21 days at 50 degrees C. Stable, continuous operation in a plug-flow reactor was demonstrated for about 3 days without any apparent problem. A maximum GOS production of 26% (w/w) of total sugars was attained at 50% lactose conversion with a feed containing 400 g/L of lactose at pH 4.5 and 40 degrees C. The corresponding reactor productivity was 6 kg/L/h, which is several-hundred-fold higher than those previously reported.     

漆酶在磁性壳聚糖微球上的固定及其酶学性质研究

以磁性壳聚糖微球为载体,戊二醛为交联剂,共价结合制备固定化漆酶。探讨了漆酶固定化的影响因素,并对固定化漆酶的性质进行了研究。确定漆酶固定化适宜条件为：50 mg磁性壳聚糖微球,加入10mL 0.8mg/mL 漆酶磷酸盐缓冲液（0.1mol/L,pH 7.0）,在4℃固定2h。固定化酶最适pH为3.0, 最适温度分别为10℃和55℃,均比游离酶降低5℃。在pH 3.0,温度37℃时,固定化酶对ABTS的表观米氏常数为171.1μmol/L。与游离酶相比,该固定化漆酶热稳定性明显提高,并具有良好的操作和存储稳定性。     

Continuous hydrolysis of tallow with immobilized lipase in a microporous membrane

Thermostable lipase from Thermomyces lanuginosus was immobilized in untreated microporous membranes. Melted tallow pumped through the membrane did not wash the enzyme out. From 0.4 to 0.9% of the soluble activity remained after immobilization with half-lives of 1-2 months or more at 50 degrees C. Membranes can be acid/base washed and reloaded with enzyme with no adverse effects. Buffer was required for a long half-life, and recycling the buffer improved the mass transfer of glycerol out of the immobilized lipase reactor. Immobilized activity was unaffected when the pH of the aqueous product changed from 5.5 to 6.5.     

Glutaraldehyde activation of polymer Nylon-6 for lipase immobilization: enzyme characteristics and stability

An extracellular alkaline lipase of a thermo tolerant Bacillus coagulans BTS-3 was immobilized onto glutaraldehyde activated Nylon-6 by covalent binding. Under optimum conditions, the immobilization yielded a protein loading of 228 microg/g of Nylon-6. Immobilized enzyme showed maximum activity at a temperature of 55 degrees C and pH 7.5. The enzyme was stable between pH 7.5-9.5. It retained 88% of its original activity at 55 degrees C for 2h and also retained 85% of its original activity after eight cycles of hydrolysis of p-NPP. Kinetic parameters Km and Vmax were found to be 4mM and 10 micromol/min/ml, respectively. The influence of organic solvents on the catalytic activity of immobilized enzyme was also evaluated. The bound lipase showed enhanced activity when exposed to n-heptane. The substrate specificity of immobilized enzyme revealed more efficient hydrolysis of higher carbon length (C-16) ester than other ones.     

Immobilization of trypsin on chitosan gels: use of different activation protocols and comparison with other supports

Trypsin was immobilized on chitosan gels coagulated with 0.1 or 1 M NaOH and activated with glutaraldehyde or glycidol. The derivatives were characterized by their recovered activity, thermal (40, 55 and 70 degrees C) and alkaline (pH 11) stabilities, amount of enzyme immobilized on gels for several enzyme loads (8-14 mg(protein)/g(Gel)) and compared to agarose derivatives. Enzyme loads higher than 14 mg(protein)/g(Gel) can be immobilized on glutaraldehyde derivatives, which showed 100% immobilization yield and, for loads up to 8 mg(protein)/g(Gel), 100% recovered activity. Activation with glycidol led to lower immobilization yields than the ones obtained with glutaraldehyde, 61% for agarose-glyoxyl (AgGly) with low grade of activation and 16% for the chitosan-glyoxyl (ChGly), but allowed obtaining the most stable derivative (ChGly), that was 660-fold more stable than the soluble enzyme at 55 and 70 degrees C-approximately threefold more stable than AgGly. The ChGly derivative presented also the highest stability during incubation at pH 11. Analyses of lysine residue contents in soluble and immobilized trypsin indicated formation of multipoint bonds between enzyme and support, for glyoxyl derivatives.     

Immobilized cyclomaltodextrin glucanotransferase of an alkalophilic Bacillus sp. No. 38-2

Cyclomaltodextrin glucanotransferase [1,4-alpha-D-glucan-4-alpha-D-(1,4-alpha-D-glucano)-transferase (cyclizing), E.C.-2.4.1.19] of an alkalophilic Bacillus sp. No. 38-2 (ATCC 21783), which contains three types of enzymes (acid, neutral, and alkaline enzymes), was immobilized on synthetic adsorption resin. No distinguishing changes in pH or thermal stabilities of enzyme were observed due to the immobilization. Since acid-enzyme activity had disappeared, the optimum pH of immobilized enzyme was 9.0. Optimum temperature for the enzyme activity changed from 50 to 55 degrees C. The enzyme converted starch to cyclodextrins without significant loss of activity under the conditions of continuous reaction for about two weeks by using the column system (60 degrees C at pH 8.0). About 63% of soluble starch solution [4% (w/v)] was changed to cyclodextrins, as tested so far.     

Characterization of dextransucrase immobilized on calcium alginate beads from Leuconostoc mesenteroides PCSIR-4

Immobilization of dextransucrase from Leuconostoc mesenteroides PCSIR-4 on alginate is optimized for application in the production of dextran from sucrose. Dextransucrase was partially purified by ethanol upto 2.5 fold. Properties of dextransucrase were less affected by immobilization on alginate beads from soluble enzyme. Highest activities of both soluble and immobilized dextransucrase found to be at 35 degrees C and optimum pH for activity remain 5.00. Substrate maxima for immobilized enzyme changed from 125 mg/ml to 200 mg/ml. Incubation time for enzyme-substrate reaction for maximum enzyme activity was increased from 15 minutes to 60 minutes in case of immobilized enzyme. Maximum stability of immobilized dextransucrase was achieved at 25 degrees C with respect to time.     

Improvement of the functional properties of a thermostable lipase from alcaligenes sp. via strong adsorption on hydrophobic supports

Lipase QL from Alcaligenes sp. is a quite thermostable enzyme. For example, it retains 75% of catalytic activity after incubation for 100 h at 55 °C and pH 7.0. Nevertheless, an improvement of the enzyme properties was intended via immobilization by covalent attachment to different activated supports and by adsorption on hydrophobic supports (octadecyl-sepabeads). This latter immobilization technique promotes the most interesting improvement of enzyme properties: (a) the enzyme is hyperactivated after immobilization: the immobilized preparation exhibits a 135% of catalytic activity for the hydrolysis of p-nitrophenyl propionate as compared to the soluble enzyme; (b) the thermal stability of the immobilized enzyme is highly improved: the immobilized preparation exhibits a half-life time of 12 h when incubated at 80 °C, pH 8.5 (a 25-fold stabilizing factor regarding to the soluble enzyme); (c) the optimal temperature was increased from 50 °C (soluble enzyme) up to 70 °C (hydrophobic support enzyme immobilized preparations); (d) the enantioselectivity of the enzyme for the hydrolysis of glycidyl butyrate and its dependence on the experimental conditions was significantly altered. Moreover, because the enzyme becomes reversibly but very strongly adsorbed on these highly hydrophobic supports, the lipase may be desorbed after its inactivation and the support may be reused. Very likely, adsorption occurs via interfacial activation of the lipase on the hydrophobic supports at very low ionic strength. On the other hand, all the covalent immobilization protocols used to immobilize the enzyme hardly improved the properties of the lipase.     

Immobilization of invertase onto poly(3-methylthienyl methacrylate)/poly(3-thiopheneacetic acid) matrix

A novel immobilization matrix, poly(3-methylthienyl methacrylate)–poly(3-thiopheneacetic acid) (PMTM–PTAA), was synthesized and used for the covalent immobilization of Saccharomyces cerevisiae invertase to produce invert sugar. The immobilization resulted in 87% immobilization efficiency. Optimum conditions for activity were not affected by immobilization and the optimum pH and temperature for both free and immobilized enzyme were found to be 4.5 and 55 °C, respectively. However, immobilized invertase was more stable at high pH and temperatures. The kinetic parameters for free and immobilized invertase were also determined using the Lineweaver–Burk plot. The K_m values were 35 and 38 mM for free and immobilized enzyme, respectively. The V_max values were 29 and 24 mg glucose/mg enzyme min for free and immobilized enzyme, respectively. Immobilized enzyme could be used for the production of glucose and fructose from sucrose since it retained almost all the initial activity for a month in storage and retained the whole activity in repeated 50 batch reactions.     

Immobilization of polygalacturonase from Aspergillus niger onto activated polyethylene and its application in apple juice clarification

The present work is focused on efficient immobilization of polygalacturonase on polyethylene matrix, followed by its application in apple juice clarification. Immobilization of polygalacturonase on activated polyethylene and its use in apple juice clarification was not reported so far. Aspergillus niger Van Tieghem (MTCC 3323) produced polygalacturonase when grown in modified Riviere's medium containing pectin as single carbon source by fed-batch culture. The enzyme was precipitated with ethanol and purified by gel filtration chromatography (Sephacryl S-100) and immobilized onto glutaraldehyde-activated polyethylene. The method is very simple and time saving for enzyme immobilization. Various characteristics of immobilized enzyme such as optimum reaction temperature and pH, temperature and pH stability, binding kinetics, efficiency of binding, reusability and metal ion effect on immobilized enzymes were evaluated in comparison to the free enzyme. Both the free and immobilized enzyme showed maximum activity at a temperature of 45 degrees C and pH 4.8. Maximum binding efficiency was 38%. The immobilized enzyme was reusable for 3 cycles with 50% loss of activity after the third cycle. Twenty-four U of immobilized enzyme at 45 degrees C and 1 h incubation time increased the transmittance of the apple juice by about 55% at 650 nm. The immobilized enzyme can be of industrial advantage in terms of sturdiness, availability, inertness, low price, reusability and temperature stability.     

温和气单孢菌YH311硫酸软骨素裂解酶的分离纯化与固定化

通过硫酸铵沉淀、QAESephadex-A50柱层析及Sephadex-G150凝胶过滤等纯化步骤,对源自温和气单孢菌YH311的ChSase进行了分离纯化。结果表明,ChSase经上述纯化步骤后被纯化了55倍,其最终纯度可达95%以上,比活为31.86u/mg。经SDSPAGE及IFE测定可知该酶的分子量约为80kD,等电点为4.3～4.8。将纯化后的ChSase用海藻酸钠或纤维素固定化后,ChSase的热稳定性及贮存稳定性均可得到大幅度的提高：固定化酶用80℃水浴处理120min或于4℃冰箱放置30d后仍可保留50%以上的相对活力;但固定化酶的收率较低,仅为18.56%和18.86%。     

Immobilization of Amaranthus leaf oxalate oxidase on alkylamine glass

A membrane bound oxalate oxidase from leaves of Amaranthus spionsus has been partially purified and immobilized on alkylamine glass with a yield of 9.2 mg protein/g support. The enzyme retained 99.4% of initial activity of free enzyme after immobilization. There was no change in the optimum pH (3.5) and Vmax but the temperature for maximum activity was slightly decreased (35 degrees C) and energy of activation (Ea) and Km for oxalate were increased after immobilization. The immobilized enzyme preparation was stable for 6 months, when stored in distilled water at 4 degrees C. Presence of Cl- did not affect the activity of immobilized enzyme.     

Characterization and optimization of β-galactosidase immobilization process on a mixed-matrix membrane

β-Galactosidase is an important enzyme catalyzing not only the hydrolysis of lactose to the monosaccharides glucose and galactose but also the transgalactosylation reaction to produce galacto-oligosaccharides (GOS). In this study, β-galactosidase was immobilized by adsorption on a mixed-matrix membrane containing zirconium dioxide. The maximum β-galactosidase adsorbed on these membranes was 1.6 g/m2, however, maximal activity was achieved at an enzyme concentration of around 0.5 g/m2. The tests conducted to investigate the optimal immobilization parameters suggested that higher immobilization can be achieved under extreme parameters (pH and temperature) but the activity was not retained at such extreme operational parameters. The investigations on immobilized enzymes indicated that no real shift occurred in its optimal temperature after immobilization though the activity in case of immobilized enzyme was better retained at lower temperature (5 °C). A shift of 0.5 unit was observed in optimal pH after immobilization (pH 6.5 to 7). Perhaps the most striking results are the kinetic parameters of the immobilized enzyme; while the Michaelis constant (K(m)) value increased almost eight times compared to the free enzyme, the maximum enzyme velocity (V(max)) remained almost constant.     

Immobilization and properties of carminomycin 4-O-methyltranferase, the enzyme which catalyzes the final step in the biosynthesis of daunorubicin in Streptomyces peucetius

The carminomycin 4-O-methyltransferase enzyme from Streptomyces peucetius was covalently immobilized on 3M Emphaze ABI-activated beads. Optimal conditions of time, temperature, pH, ionic strength, enzyme, substrate (carminomycin), and cosubstrate (S-adenosyl-L-methionine) concentrations were defined for the immobilization reaction. Protein immobilization yield ranged from 52% to 60%. Including carminomycin during immobilization had a positive effect on the activity of the immobilized enzyme but a strongly negative effect on the coupling efficiency. The immobilized enzyme retained at least 57% of its maximum activity after storage at 4 degrees C for more than 4 months. The properties of the free and immobilized enzyme were compared to determine whether immobilization could alter enzyme activity. Both soluble and bound enzyme exhibited the same pH profile with an optimum near 8.0. Immobilization caused an approximately 50% decrease in the apparent K(m) (K'(m)) for carminomycin while the K'(m) for S-adenosyl-L-methionine was approximately doubled. A 57% decrease in the V(max) value occurred upon immobilization. These changes are discussed in terms of active site modifications as a consequence of the enzyme immobilization. This system has a potential use in bioreactors for improving the conversion of carminomycin to daunorubicin. (c) 1995 John Wiley & Sons, Inc.     

Continuous production of fructooligosaccharides using fructosyltransferase immobilized on ion exchange resin

A continuous production of fructooligosaccharides from sucrose was investigated by fructosyltransferase immobilized on a high porous resin, Diaion HPA 25. The optimum pH (5.5) and temperature (55°C) of the enzyme for activity was unaltered by immobilization, and the immobilized enzyme became less sensitive to the pH change. The optimal operation conditions of the immobilized enzyme column for maximizing the productivity were as follows: 600 g/L of sucrose feed concentration, flow rate of superficial space velocity 2.7 h^?1. When the enzyme column was run at 50°C, about 8% loss of the initial activity of immobilized enzyme was observed after 30 days of continuous operation, during which high productivity of 1174 g/L·h was achieved. The kinds of products obtained using the immobilized enzyme were almost the same as those using soluble enzymes or free cells.     

Preparation and characterization of kappa-carrageenan immobilized urease

Urease was encapsulated within kappa-carrageenan beads. Various parameters, such as amount of kappa-carrageenan and enzyme activity, were optimized for the immobilization of urease. Immobilized urease was thoroughly characterized for pH, temperature, and storage stabilities and these properties were compared with the free enzyme. The free urease activity quickly decreased and the half time of the activity decay was about 3 days at 4 degrees C. The immobilized urease remained very active over a long period of time and this enzyme lost about 70.43% of its orginal activity over the period of 26 days for storage at 4 degrees C. The Michaelis constant (Km) and maximum reaction velocity (Vmax) were calculated from Lineweaver-Burk plots for both free and immobilized enzyme systems. Vmax = 227.3 U/mg protein, Km = 65.6 mM for free urease and Vmax = 153.9 U/mg protein, Km = 96.42 mM for immobilized urease showed a moderate decrease of enzyme specific activity and change of substrate affinity.     

Direct immobilization of tyrosinase enzyme from natural mushrooms (Agaricus bisporus) on D-sorbitol cinnamic ester

Mushroom tyrosinase was immobilized from an extract onto the totally cinnamoylated derivative of D-sorbitol by direct adsorption as a result of the intense hydrophobic interactions that took place. The immobilization pH value and mass of lyophilized mushrooms were important parameters that affected the immobilization efficiency, while the immobilization time and immobilization support concentration were not important in this respect. The extracted/immobilized enzyme could best be measured above pH 3.5 and the optimum measuring temperature was 55 degrees C. The apparent Michaelis constant using 4-tert-butylcatechol as substrate was 0.38+/-0.02 mM, which was lower than for the soluble enzyme from Sigma (1.41+/-0.20 mM). Immobilization stabilized the extracted enzyme against thermal inactivation and made it less susceptible to activity loss during storage. The operational stability was higher than in the case of the tyrosinase supplied by Sigma and immobilized on the same support. The results show that the use of p-nitrophenol as enzyme-inhibiting substrate during enzyme extraction and immobilization made the use of ascorbic acid unnecessary and is a suitable method for extracting and immobilizing the tyrosinase enzyme, providing good enzymatic activity and stability.     

Immobilization of lactate dehydrogenase on polyacrylamide beads

Pig muscle lactate dehydrogenase (L-lactate:NAD oxidoreductase, EC 1.1.1.27) was covalently immobilized on polyacrylamide beads containing carboxylic functional groups activated by water-soluble carbodiimide. The effects of immobilization on the catalytic properties and stability of the lactate dehydrogenase were studied. There was no shift in the pH optimum of the immobilized enzyme compared to that of the soluble one. The apparent optimum temperature of the soluble enzyme was 65 degrees C, while that of the immobilized enzyme was between 50 and 65 degrees C. The apparent Km values of the immobilized enzyme with pyruvate and NADH substrates were higher than those of the soluble enzyme. As a result of immobilization, enhanced stabilities were found against heat treatment, changes in pH, and urea denaturation.     

Enzymatic properties of immobilized Alcaligenes faecalis cells with cell-associated beta-glucosidase activity

Enzymatic properties of Alcaligenes faecalis cells immobilized in polyacrylamide were characterized and compared with those reported for the extracted enzyme, and with those measured for free cells. Many of the properties reflected those of the extracted enzyme rather than those measured in the free whole cells prior to immobilization, suggesting cell disruption during immobilization. These properties included the pH activity profile, a slightly broader pH stability profile, and the activation energy. Electron micrographs showed evidence of cell debris among the polymer matrix. The immobilized cells were not viable, and did not consume glucose. Thermal stability was less after immobilization with a half-life of 16 h at 45 degrees C, and 3.5 h at 50 degrees C. The immobilized preparation was more stable when stored lyophilized rather than in buffer, losing 23 and 52% activity, respectively, after six months. The enzyme was irreversibly inhibited by both acetate and citrate buffers. If the immobilized enzyme is to be used in conjunction with cellulases from Trichoderma reesei for cellulase saccharification, the optimal conditions would be pH 5.5 and 45 degrees C in a buffer containing no carboxylic acid groups.