Effect of dissolved oxygen concentration and impeller tip speed on itaconic acid production by Aspergillus terreus

Summary Effect of aeration rate and impeller tip speed on mycelium growth and itaconic acid production was investigated in a batch culture of Aspergillus terreus IFO-6365. When impeller tip speed was 94.2 cm/sec at a fixed aeration rate of 0.5 vvm, itaconic acid concentration was 3.6 and 1.6 times higher than those in the impeller tip speed of 62.8 and 125.7 cm/sec, respectively. When an oxygen-enriched air was supplied at a fixed impeller tip speed of 94.2 cm/sec and dissolved oxygen concentration was maintained in the 20–60 % range, both itaconic acid concentration and mycelium growth were not affected by the dissolved oxygen concentration.     

Influence of pH and impeller tip speed on the cultivation of<Emphasis Type="Italic">Bifidobacterium pseudocatenulatum</Emphasis> G4 in a milk-based medium

Biomass production ofBifidobacterium pseudocatenulatum G4 in a milk-based medium was carried out in a 2- and 10-L stirred tank fermenters. The effects of impeller tip speed (0.28, 0.56, and 0.83 m/s) and pH control (6.0, 6.5, and 7.0) on the biomass production were investigated. The growth performance in the 2-L fermenter was significantly improved when the impeller tip speed was held constant at 0.56 m/s and the pH was controlled at 6.5. These conditions yielded a maximum biomass of 1.687×10⁹ cfu/mL, a maximum specific growth rate of 0.504 h⁻¹, a biomass productivity of 9.240×10⁷ cfu/mL·h, and a biomass yield of 9.791×10¹⁰ cfu/g lactose. The consumption of milk lactose resulted in the accumulation of 7.353 g/L acetic acid and 6.515 g/L lactic acid, with an acetic:lactic ratio of 1.129. Scale-up of the fermentation process to a 10-L fermenter based on a constant impeller tip speed of 0.56 m/s yielded reproducible results with respect to biomass production and cell viability.     

The induction and repression of benzene and catechol oxidizing capacity of Pseudomonas putida ML2 studied in perturbed chemostat culture

The oxidation of catechol, an intermediate in benzene catabolism, was studied using transient variations in dissolved oxygen tension (DOT) when a succinate limited steady state culture of Pseudomonas putida ML2 was perturbed with a pulse of another substrate. A model was developed and tested for the effect of fluctuations in oxidizing enzyme activity on DOT. It was found that the rate of induction of catechol oxidizing enzymes was independent of dilution rate up to a relative growth rate /_max of 0.75. Only at higher dilution rates was catabolite repression observed.Abbreviations DOT dissolved oxygen tension - K _L a gas transfer coefficient - specific growth rate - _max maximum specific growth rate - K_s substrate saturation constant     

The effect of dissolved oxygen tension on 11β- and 19-hydroxylation of Reichstein's Substance S by Pellicularia filamentosa

Summary The 11- and 19-hydroxylation enzyme(s) of Pellicularia filamentosa IFO 6298 have been shown to be inducible by Reichstein's Substance S. By using the protein synthesis inhibitor, cycloheximide, in fermenter culture the effects of dissolved oxygen tension (DOT) on enzyme induction and enzyme expression have been separately investigated. For both hydroxylations, an optimum DOT for induction has been shown at 15% of saturation, while the optimum for expression is at 30% of saturation. The results have been verified in the absence of cycloheximide. Thus, maximum rates of hydroxylation are achieved when induction is performed at low DOT, followed by elevation to ensure maximum expression.     

Study of biphenyl hydroxylase activity in Aspergillus parasiticus using a colorimetric assay

A colorimetric assay, based on the hydroxylation of 4-nitrobiphenyl (NBP), allows for the first time the quick measurement of the biphenyl hydroxylase activity of whole liquid cultures of Aspergillus parasiticus. The assay can be used to measure the activity in whole cultures containing biphenyl hydroxylase substrates other than NBP. The assay was used to investigate the magnitude and time dependence of the activity induced by different culture treatments. The biphenyl hydroxylase activities measured by the assay correlate with the rates of biphenyl substrate hydroxylation as determined by chromatographic (HPLC) analysis, so the assay is a convenient alternative to the HPLC method for determining effects of culture conditions on hydroxylation rates. The assay was used to demonstrate that biphenyl substrates (4-bromobiphenyl and m-terphenyl) and a product of biphenyl hydroxylation (4,4-dihydroxybiphenyl) induce (i.e., stimulate synthesis of) the hydroxylase system. The rates of hydroxylation of NBP observed in the assays (up to 0.6 g product/l per hour) are considerably higher than the rates of biphenyl substrate hydroxylation previously reported in cultures of A. parasiticus. Correspondence to: D. P. Mobley     

Reactor properties of a high-speed bead mill for microbial cell rupture

Laboratory and pilot-plant high-speed bead mills of 0.6 and 5 liter capacity and consisting of four and five impellers in series, respectively, were used to follow the batch and continuous disruption of bakers' yeast (Saccharomyces cerevisiae). The mills are not scaled equivalents. Throughputs ranging from 1 × 10^?6m³/sec to 12 × 10^?6m³/sec for the 0.6 liter mill and from 16 × 10^?6m³/sec to 100 × 10^?6m³/sec for the 5 liter mill were used for continuous disruption studies. Variables studied included the effect of impeller tip speed, temperature, and packed yeast concentration (ranging from 15 to75% by weight packed yeast). Disruption kinetics, as measured by the release of soluble protein, followed a first-order rate equation, the rate constant being a function of impeller tip speed and yeast concentration. For continuous disruption studies the bead mills behaved as a series of continuous stirred-tank reactors, each impeller forming a reactor. In the smaller mill a considerable degree of backflow between the reactors was evident. For certain mixing conditions the maximum amount of releasable protein was dependent on the impeller geometry, construction material, and also the concentration of packed yeast. The relative power efficiencies of the two mills are discussed along with possible criteria for scaling of bead mills.     

Uncoupling and isotope effects in γ-butyrobetaine hydroxylation

Replacement of unlabeled -butyrobetaine with -[2,3,4-²H₆]butyrobetaine has a profound effect on the stoichiometry between decarboxylation of 2-oxoglutarate and hydroxylation in the reaction catalyzed by human -butyrobetaine hydroxylase. The ratios between decarboxylation and hydroxylation are 1.16 with Unlabeled and 7.48 with deuterated -butyrobetaine as substrate. From these ratios an internal isotope effect of 41 has been calculated. DV in the overall reaction measured as 2- oxoglutarate decarboxylation is 2.5 and D_V/K is 1.0. For -butyrobetaine hydroxylase fromPseudomonas sp. AK 1, 2-oxoglutarate decarboxylation exceeds hydroxylation with 10% when deuterated -butyrobetaine is used. No excess was found with unlabeled substrate and no internal isotope effect could be calculated. D_V for the bacterial enzyme is 6.     

Concomitant hydroxylation of proline and lysine residues in collagen using purified enzymes in vitro

Concomitant hydroxylation of proline and lysine residues in protocollagen was studied using purified enzymes. The data suggest that prolyl 4-hydroxylase (prolyl-glycyl-peptide, 2-oxoglutarate: oxygen oxidoreductase (4-hydroxylating), EC 1.14.11.2) and lysyl hydroxylase (peptidyllysine, 2-oxoglutarate; oxygen 5-oxidoreductase, EC 1.14.11.4) are competing for the protocollagen substrate, this competition resulting in an inhibition of the lysyl hydroxylase but not of the prolyl 4-hydroxylase reaction. When the same protocollagen was used for these hydroxylases, the affinity of prolyl 4-hydroxylase to the protocollagen substrate was about 2-fold higher than that of lysyl hydroxylase. Hydroxylation of lysine residues in protocollagen had no effect on the affinity of prolyl 4-hydroxylase, whereas hydroxylation of proline residues decreased the affinity of lysyl hydroxylase to one-half of the value determined before the hydroxylation. When enzyme preparations containing different ratios of lysyl hydroxylase activity to prolyl 4-hydroxylase activity were used to hydroxylase protocollagen substrate, it was found that in the case of a low ratio the hydroxylation of lysine residues seemed to proceed only after a short lag period. Accordingly, it seems probable that most proline residues are hydroxylated to 4-hydroxyproline residues before hydroxylation of lysine residues if the prolyl 4-hydroxylase and lysyl hydroxylase are present as free enzymes competing for the same protocollagen substrate.     

The disruption ofSaccharomyces cerevisiae cells and release of glucose 6-phosphate dehydrogenase (G6PDH) in a horizontal dyno bead mill operated in continuous recycling mode

Baker’s yeast was disrupted in a 1.4-L stainless steel horizontal bead mill under a continuous recycle mode using 0.3 mm diameter zirconia beads as abrasive. A single pass in continuous mode bead mill operation liberates half of the maximally released protein. The maximum total protein release can only be achieved after passaging the cells 5 times through the disruption chamber. The degree of cell disruption was increased with the increase in feeding rate, but the total protein release was highest at the middle range of feeding rate (45 L/h). The total protein release was increased with an increase in biomass concentration from 10 to 50% (w/v). However, higher heat dissipation as a result of high viscosity of concentrated biomass led to the denaturation of labile protein such as glucose 6-phosphate dehydrogenase (G6PDH). As a result the highest specific activity of G6PDH was achieved at biomass concentration of 20% (ww/v). Generally, the degree of cell disruption and total protein released were increased with an increase in impeller tip speed, but the specific activity of G6PDH was decreased substantially at higher impeller tip speed (14 m/s). Both the degree of cell disruption and total protein release increased, as the bead loading increased from 75 to 85% (v/v). Hence, in order to obtain a higher yield of labile protein such as G6PDH, the yeast cell should not be disrupted at biomass concentration and impeller tip speed higher than 20% (w/v) and 10 m/s, respectively.     

The hydroxylation of phenylalanine and tyrosine by tyrosine hydroxylase from cultured pheochromocytoma cells.

Pheochromocytoma tyrosine hydroxylase was reported to have unusual catalytic properties, which might be unique to the tumor enzyme (Dix, T. A., Kuhn, D. M., and Benkovic, S. J. (1987) Biochemistry 24, 3354-3361). Two such properties, namely the apparent inability to hydroxylate phenylalanine and an unprecedented reactivity with hydrogen peroxide were investigated further in the present study. Tyrosine hydroxylase was purified to apparent homogeneity from cultured pheochromocytoma PC12 cells. The purified tumor enzyme was entirely dependent on tetrahydrobiopterin (BH4) for the hydroxylation of tyrosine to 3,4-dihydroxyphenylalanine and hydrogen peroxide could not substitute for the natural cofactor. Indeed, in the presence of BH4, increasing concentrations of hydrogen peroxide completely inhibited enzyme activity. The PC12 hydroxylase exhibited typical kinetics of tyrosine hydroxylation exhibited typical kinetics of tyrosine hydroxylation, both as a function of tyrosine (S0.5 Tyr = 15 microM) and BH4 (apparent Km BH4 = 210 microM). In addition, the enzyme catalyzed the hydroxylation of substantial amounts of phenylalanine to tyrosine and 3,4-dihydroxyphenylalanine (apparent Km Phe = 100 microM). Phenylalanine did not inhibit the enzyme in the concentrations tested, whereas tyrosine showed typical substrate inhibition at concentrations greater than or equal to 50 microM. At higher substrate concentrations, the rate of phenylalanine hydroxylation was equal to or exceeded that of tyrosine. Essentially identical results were obtained with purified tyrosine hydroxylase from pheochromocytoma PC18 cells. The data suggest that the tumor enzyme has the same substrate specificity and sensitivity to hydrogen peroxide as tyrosine hydroxylase from other tissues.     

The influence of bakers’ yeast cells on protein adsorption in anion exchange expanded bed chromatography

Baker’s yeast was disrupted in a 1.4-L stainless steel horizontal bead mill under a continuous recycle mode using 0.3 mm diameter zirconia beads as abrasive. A single pass in continuous mode bead mill operation liberates half of the maximally released protein. The maximum total protein release can only be achieved after passaging the cells 5 times through the disruption chamber. The degree of cell disruption was increased with the increase in feeding rate, but the total protein release was highest at the middle range of feeding rate (45 L/h). The total protein release was increased with an increase in biomass concentration from 10 to 50% (w/v). However, higher heat dissipation as a result of high viscosity of concentrated biomass led to the denaturation of labile protein such as glucose 6-phosphate dehydrogenase (G6PDH). As a result the highest specific activity of G6PDH was achieved at biomass concentration of 20% (ww/v). Generally, the degree of cell disruption and total protein released were increased with an increase in impeller tip speed, but the specific activity of G6PDH was decreased substantially at higher impeller tip speed (14 m/s). Both the degree of cell disruption and total protein release increased, as the bead loading increased from 75 to 85% (v/v). Hence, in order to obtain a higher yield of labile protein such as G6PDH, the yeast cell should not be disrupted at biomass concentration and impeller tip speed higher than 20% (w/v) and 10 m/s, respectively.     

Mechanism of "uncoupled" tetrahydropterin oxidation by phenylalanine hydroxylase

Phenylalanine hydroxylase can catalyze the oxidation of its tetrahydropterin cofactor without concomitant substrate hydroxylation. We now report that this "uncoupled" tetrahydropterin oxidation is mechanistically distinct from normal enzyme turnover. Tetrahydropterins are oxygenated to 4a-carbinolamines only during catalytic events involving substrate hydroxylation. In the absence of hydroxylation tetrahydropterins are oxidized directly to quinonoid dihydropterins. Stoichiometry studies define a ratio of two tetrahydropterins oxidized per O2 consumed in uncoupled enzyme turnover, thus indicating the complete reduction of O2 to H2O. Complementary results establish the lack of H2O2 production by the enzyme when uncoupled and define a tetrahydropterin oxidase activity for the enzyme. Thus, the hydroxylating intermediate of phenylalanine hydroxylase may be discharged in two ways, by substrate hydroxylation or by electron abstraction. A mechanism is proposed for the uncoupled oxidation of tetrahydropterins by phenylalanine hydroxylase, and the significance of these findings is discussed.     

Molecular cloning and analysis of the genes encoding the 4-hydroxyphenylacetate hydroxylase from Klebsiella pneumoniae

The Klebsiella pneumoniae genes encoding the hydroxylase involved in the meta-cleavage pathway of 4-hydroxyphenylacetic acid (4-HPA) were cloned, and the DNA fragment from the region essential for hydroxylase activity was sequenced. K. pneumoniae 4-HPA hydroxylase was composed of two proteins (HpaA and HpaH) with different molecular masses. HpaA seems to be a flavin-containing hydroxylase with a molecular mass of 58,781 Da. HpaH, with a molecular mass of 18,680 Da, seems to be a “helper” protein required for productive hydroxylation of the substrate. The hpa genes were expressed and the hydroxylase was active in Escherichia coli. Comparison of the enzyme with other monooxygenases indicates that K. pneumoniae 4-HPA hydroxylase is a member of a new family of hydroxylases. Received: 21 August 1996 / Accepted: 6 December 1996     

Effects of agitation on the microalgae Phaeodactylum tricornutum and Porphyridium cruentum

The effect of mechanical agitation on the microalgae Phaeodactylum tricornutum and Porphyridium cruentum was investigated in aerated continuous cultures with and without the added shear protectant Pluronic F68. Damage to cells was quantified through a decrease in the steady state concentration of the biomass in the photobioreactor. For a given aeration rate, the steady state biomass concentration rose with increasing rate of mechanical agitation until an upper limit on agitation speed was reached. This maximum tolerable agitation speed depended on the microalgal species. Further increase in agitation speed caused a decline in the steady state concentration of the biomass. An impeller tip speed of >1.56 m s^–1 damaged P. tricornutum in aerated culture. In contrast, the damage threshold tip speed for P. cruentum was between 2.45 and 2.89 m s^–1. Mechanical agitation was not the direct cause of cell damage. Damage occurred because of the rupture of small gas bubbles at the surface of the culture, but mechanical agitation was instrumental in generating the bubbles that ultimately damaged the cells. Pluronic F68 protected the cells against damage and increased the steady state concentration of the biomass relative to operation without the additive. The protective effect of Pluronic was concentration-dependent over the concentration range of 0.01–0.10% w/v.     

Mechanism of oxygen activation by tyrosine hydroxylase

The mechanism by which the tetrahydropterin-requiring enzyme tyrosine hydroxylase (TH) activates dioxygen for substrate hydroxylation was explored. TH contains one ferrous iron per subunit and catalyzes the conversion of its tetrahydropterin cofactor to a 4a-carbinolamine concomitant with substrate hydroxylation. These results are in accord with shared mechanisms of oxygen activation by TH and the more commonly studied tetrahydropterin-dependent enzyme phenylalanine hydroxylase (PAH) and strongly suggest that a peroxytetrahydropterin is the hydroxylating species generated during TH turnover. In addition, TH can also utilize H2O2 as a cofactor for substrate hydroxylation, a result not previously established for PAH. A detailed mechanism for the reaction is proposed. While the overall pattern of tetrahydropterin-dependent oxygen activation by TH and PAH is similar, the H2O2-dependent hydroxylation performed by TH provides an indication that subtle differences in the Fe ligand field exist between the two enzymes. The mechanistic ramifications of these results are briefly discussed.     

Possible involvement of G-proteins and cAMP in the induction of progesterone hydroxylating enzyme system in the vascular wilt fungus Fusarium oxysporum

Fungi present the ability to hydroxylate steroids. In some filamentous fungi, progesterone induces an enzyme system which converts the compound into a less toxic hydroxylated product. We investigated the progesterone response in the vascular wilt pathogen Fusarium oxysporum, using mass spectrometry and high performance liquid chromatography (HPLC). Progesterone was mainly transformed into 15α-hydroxyprogesterone, which was found predominantly in the extracellular medium. The role of two conserved fungal signaling cascades in the induction of the progesterone-transforming enzyme system was studied, using knockout mutants lacking the mitogen-activated protein kinase Fmk1 or the heterotrimeric G-protein β subunit Fgb1 functioning upstream of the cyclic adenosine monophosphate (cAMP) pathway. No steroid hydroxylation was induced in the Δfgb1 strain, suggesting a role for the G-protein β subunit in progesterone signaling. Exogenous cAMP restored the induction of progesterone-transforming activity in the Δfgb1 strain, suggesting that steroid signaling in F. oxysporum is mediated by the cAMP-PKA pathway.     

Distribution of phenylalanine hydroxylase (EC 1.14.3.1) in liver and kidney of vertebrates.

The range of phenylalanine hydroxylase activity was determined by measuring the conversion of radioactive phenylalanine to tyrosine in liver and kidney of various vertebrates. Rodents (rats, mouse, gerbil, hamster and guinea pig) were found to have the highest liver phenylalanine hydroxylase activity among all animals studied. They are also the only species that possessed a significant kidney phenylalanine hydroxylase activity which was about 25% of that found in the liver of the same animal. The synthetic dimethyl-tetrahydro-pteridine, used as a cofactor for the enzyme assay in most studies, catalyzed non-enzymatic hydroxylation of phenylalanine to tyrosine. Inclusion of boiled-blank and strict control of timing between incubation and product measurement were essential precautions to minimize erroneous results from substrate contamination and non-enzymatic hydroxylation.     

Transformation of progesterone by a thermophilic bacillus

Abstract When a thermophilic bacillus was incubated with progesterone for approx. 18 h at 65°C, four progesterone-based metabolites were produced in moderate quantities. Two products were found to be hydroxy derivatives, i.e. 6α-hydroxyprogesterone and 6β-hydroxyprogesterone and two were C-20 reduced epimers of progesterone, i.e. 20α- and 20β-dihydroprogesterone. 6α-Hydroxyprogesterone is a rare microbial transformation product.
Inhibition of hydroxylation by azole-based fungicides and the presence of a carbon-monoxide-reduced difference-spectrum absorbance maximum at 448 nm in the soluble cell fraction suggest that the hydroxylase(s) might be cytochromes(s) P450. The dihydroprogesterones were probably produced by oxidoreductases.     

Mechanistic studies of p-hydroxybenzoate hydroxylase reconstituted with 2-Thio-FAD

2-Thio-FAD (oxygen substituent at position 2 is replaced by sulfur) was used to reconstitute the apoenzyme of p-hydroxybenzoate hydroxylase. The 2-thio-FAD enzyme differs from native enzyme in several respects. While the native enzyme catalyzes the fully coupled hydroxylation of p-hydroxybenzoate, the 2-thio-FAD enzyme shows no hydroxylation of this substrate, instead reducing molecular oxygen to hydrogen peroxide. The rate of reduction of 2-thio-FAD p-hydroxybenzoate hydroxylase by NADPH in the presence of substrate was 7-fold faster than with the native enzyme. However, the oxygen reactivity of the reduced 2-thio-FAD enzyme was less than 1% that of native enzyme. This slow oxygen reaction results in the very high KmO2 observed in steady state kinetic studies of the modified enzyme. Stopped flow studies of the oxygen reaction of the reduced 2-thio-FAD enzyme in the presence of substrate confirmed the formation of a transient intermediate. The spectrum of this intermediate is very similar to those of the flavin-C(4a) adducts obtained with 2-thio-FMN lactate oxidase. This evidence suggests that reduced 2-thio-FAD p-hydroxybenzoate hydroxylase forms a flavin-C(4a)-hydroperoxide on reaction with oxygen in a reaction analogous to that with native enzyme, but that the resulting peroxyflavin is incompetent as an oxygenating species, breaking down instead to oxidized 2-thio-FAD enzyme and hydrogen peroxide.