Development of a helical-ribbon impeller bioreactor for high-density plant cell suspension culture

A double helical-ribbon impeller (HRI) bioreactor with a 11-L working volume was developed to grow high-density Catharanthus roseus cell suspensions. The rheological behavior of this suspension was found to be shear-thinning for concentrations higher than 12 to 15 g DW . L(-1). A granulated agar suspension of similar rheological properties was used as a model fluid for these suspensions. Mixing studies revealed that surface baffling and bottom profiling of the bioreactor and impeller speeds of 60 to 150 rpm ensured uniform mixing of suspensions. The HRI power requirement was found to increase singnificantly for agar suspensions higher than 13 g DW . L(-1), in conjunction with the effective viscosity increase. Oxygen transfer studies showed high apparent surface oxygen transfer coefficients (k(L)a approximately 4 to 45 h(-1)) from agar suspensions of 30 g DW . L(-1) to water and for mixing speeds ranging from 120 to 150 rpm. These high surface k(I)a values were ascribed to the flow pattern of this bioreactor configuration combined with surface bubble generation and entrainment in the liquid phase caused by the presence of the surface baffles. High-density C. roseus cell suspension cultures were successfully grown in this bioreactor without gas sparging. Up to 70% oxygen enrichment of the head space was required to ensure sufficient oxygen supply to the cultures so that dissolved oxygen concentration would remain above the critical level (>/=10% air saturation). The best mixing speed was 120 rpm. These cultures grew at the same rate ( approximately 0.4 d(-1)) and attained the same high biomass concentrations ( approximately 25 to 27 g DW . L(-1), 450 to 500 g filtered wet biomass . L(-1), and 92% to 100% settled wet biomass volume) as shake flask cultures. The scale-up potential of this bioreactor configuration is discussed.     

Effect of oxygen transfer on glycerol biosynthesis by an osmophilic yeast Candida magnoliae I(2)B

The influence of oxygen on glycerol production by an osmophilic yeast, Candida magnoliae I(2)B, was studied in a bioreactor. Oxygen transfer rates (OTRs) and volumetric oxygen transfer coefficients (k(L)a) were determined at different aeration and agitation rates. Cell growth as well as glycerol production was strongly affected by oxygen supply. Improvement in OTRs resulted in increased cell growth and glycerol yield. However, at high OTRs, there was a reduction in glucose uptake rate, indicating Pasteur Effect, and glycerol accumulation was also reduced at k(L)a of 253 h(-1). The availability of oxygen per unit of cell mass was found to be the most important factor that controlled cell growth, glucose uptake, and glycerol yield. The overall productivity and yield of glycerol could be related with k(L)a. The biosynthesis of glycerol was found to both growth- and non-growth-associated, although glycerol was mainly produced in post-exponential phase.     

Oxygen mass transfer and scale-up studies in baffled roller bioreactors

Oxygen mass transfer was studied in conventional, bead mill and baffled roller bioreactors. Using central composite rotational design, impacts of size, rotation speed and working volume on the oxygen mass transfer were evaluated. Baffled roller bioreactor outperformed its conventional and bead mill counterparts, with the highest k _L a obtained in these configurations being 0.58, 0.19, 0.41 min^?1, respectively. Performances of the bead mill and baffled roller bioreactor were only comparable when a high bead loading (40 %) was applied. Regardless of configuration increase in rotation speed and decrease in working volume improved the oxygen mass transfer rate. Increase in size led to enhanced mass transfer and higher k _L a in baffled roller bioreactor (0.49 min^?1 for 2.2 L and 1.31 min^?1 for 55 L bioreactors). Finally, the experimentally determined k _L a in the baffled roller bioreactors of different sizes fit reasonably well to an empirical correlation describing the k _L a in terms of dimensionless numbers.     

A study of oxygen transfer in shake flasks using a non-invasive oxygen sensor

We describe a study of oxygen transfer in shake flasks using a non-invasive optical sensor. This study investigates the effect of different plugs, presence of baffles, and the type of media on the dissolved oxygen profiles during Escherichia coli fermentation. We measured the volumetric mass transfer coefficient (k(L)a) under various conditions and also the resistances of the various plugs. Finally, we compared shake flask k(L)a with that from a stirred tank fermentor. By matching k(L)a's we were able to obtain similar growth and recombinant protein product formation kinetics in both a fermentor and a shake flask. These results provide a quantitative comparison of fermentations in a shake flask vs. a bench-scale fermentor and should be valuable in guiding scale-up efforts.     

Modeling of growth and laccase production by Pycnoporus sanguineus

Production of extracellular laccase by the white-rot fungus Pycnoporus sanguineus was examined in batch submerged cultures in shake flasks, baffled shake flasks and a stirred tank bioreactor. The biomass growth in the various culture systems closely followed a logistic growth model. The production of laccase followed a Luedeking-Piret model. A modified Luedeking-Piret model incorporating logistic growth effectively described the consumption of glucose. Biomass productivity, enzyme productivity and substrate consumption were enhanced in baffled shake flasks relative to the cases for the conventional shake flasks. This was associated with improved oxygen transfer in the presence of the baffles. The best results were obtained in the stirred tank bioreactor. At 28 °C, pH 4.5, an agitation speed of 600 rpm and a dissolved oxygen concentration of ~25 % of air saturation, the laccase productivity in the bioreactor exceeded 19 U L^?1 days^?1, or 1.5-fold better than the best case for the baffled shake flask. The final concentration of the enzyme was about 325 U L^?1.     

Quantification of power consumption and oxygen transfer characteristics of a stirred miniature bioreactor for predictive fermentation scale-up

Miniature parallel bioreactors are becoming increasingly important as tools to facilitate rapid bioprocess design. Once the most promising strain and culture conditions have been identified a suitable scale-up basis needs to be established in order that the cell growth rates and product yields achieved in small scale optimization studies are maintained at larger scales. Recently we have reported on the design of a miniature stirred bioreactor system capable of parallel operation [Gill et al. (2008); Biochem Eng J 39:164-176]. In order to enable the predictive scale-up of miniature bioreactor results the current study describes a more detailed investigation of the bioreactor mixing and oxygen mass transfer characteristics and the creation of predictive engineering correlations useful for scale-up studies. A Power number of 3.5 for the miniature turbine impeller was first established based on experimental ungassed power consumption measurements. The variation of the measured gassed to ungassed power ratio, P(g)/P(ug), was then shown to be adequately predicted by existing correlations proposed by Cui et al. [Cui et al. (1996); Chem Eng Sci 51:2631-2636] and Mockel et al. [Mockel et al. (1990); Acta Biotechnol 10:215-224]. A correlation relating the measured oxygen mass transfer coefficient, k(L)a, to the gassed power per unit volume and superficial gas velocity was also established for the miniature bioreactor. Based on these correlations a series of scale-up studies at matched k(L)a (0.06-0.11 s(-1)) and P(g)/V (657-2,960 W m(-3)) were performed for the batch growth of Escherichia coli TOP10 pQR239 using glycerol as a carbon source. Constant k(L)a was shown to be the most reliable basis for predictive scale-up of miniature bioreactor results to conventional laboratory scale. This gave good agreement in both cell growth and oxygen utilization kinetics over the range of k(L)a values investigated. The work described here thus gives further insight into the performance of the miniature bioreactor design and will aid its use as a tool for rapid fermentation process development.     

A restructured framework for modeling oxygen transfer in two-phase partitioning bioreactors

This communication proposes a mechanistic modification to a recently published method for analyzing oxygen mass transfer in two-phase partitioning bioreactors (Nielsen et al., 2003), and corrects an oversight in that paper. The newly proposed modification replaces the earlier empirical approach, which treated the two liquid phases as a single, homogeneous liquid phase, with a two-phase mass transfer model of greater fundamental rigor. Additionally, newly developed empirical models are presented that predict the mass transfer coefficient of oxygen absorption in both aqueous medium and an organic phase (n-hexadecane) as a function of bioreactor operating conditions. Experimental values and theoretical predictions of mass transfer coefficients in two-phase dispersions, k(L)a(TP), are compared. The revised approach more clearly demonstrates the potential for oxygen mass transfer enhancement by organic phase addition, one of the motivations for employing a distinct second phase in a partitioning bioreactor.     

Optimization of oxygen mass transfer in a multiphase bioreactor with perfluorodecalin as a second liquid phase

Oxygenation is an important parameter involved in the design and operation of mixing-sparging bioreactors and it can be analyzed by means of the oxygen mass transfer coefficient (k(L)a). The operational conditions of a stirred, submerged aerated 2-L bioreactor have been optimized by studying the influence of a second liquid phase with higher oxygen affinity (perfluorodecalin or olive oil) in the k(L)a. Using k(L)a measurements, the influence of the following parameters on the oxygen transfer rate was evaluated: the volume of working medium, the type of impellers and their position, the organic phase concentration, the aqueous phase composition, and the concentration of inactive biomass. This study shows that the best experimental conditions were achieved with a perfluorodecalin volume fraction of 0.20, mixing using two Rushton turbines with six vertical blades and in the presence of YPD medium as the aqueous phase, with a k(L)a value of 64.6 h(-1). The addition of 20% of perfluorodecalin in these conditions provided a k(L)a enhancement of 25% when pure water was the aqueous phase and a 230% enhancement when YPD medium was used in comparison to their respective controls (no perfluorodecalin). Furthermore it is shown that the presence of olive oil as a second liquid phase is not beneficial to the oxygen transfer rate enhancement, leading to a decrease in the k(L)a values for all the concentrations studied. It was also observed that the magnitude of the enhancement of the k(L)a values by perfluorodecalin depends on the biomass concentration present.     

Oxygen transfer and consumption in a thiosulfate oxidizing bioreactor with sulfur production

AIMS: To evaluate the contribution of oxygen transfer and consumption in a sulfoxidizing system to increase the elemental sulfur yield from thiosulfate oxidation. METHODS AND RESULTS: A 10 l thiosulfate oxidizing bioreactor with suspended cells operating under microaerophilic conditions and a separated aerator with a variable volume of 0.8--1.7 l were operated with a consortium containing mainly Thiobacillus sp. that oxidizes several sulfide species to elemental sulfur and sulfate. From the gas-liquid oxygen balance, the k(L)a was estimated under different operation conditions. A k(L)a of around 200 h(-1) favoured elemental sulfur production and can serve as scale-up criterion. It was further shown that more than 50% of the oxygen fed to the system was consumed in the aerator. CONCLUSIONS: The performance of the sulfoxidizing system can be improved by controlling oxygen transfer. SIGNIFICANCE AND IMPACT OF THE STUDY: The proposed method for the k(L)a determination was based on the oxygen balance, which incorporates the oxygen concentrations measured in the liquid in steady state, reducing the interference of the response time in the traditional non-steady state methods. This approach can be used to optimize reactors where microaerophilic conditions are desirable.     

Prediction of gas-liquid mass transfer coefficient in sparged stirred tank bioreactors

Oxygen mass transfer in sparged stirred tank bioreactors has been studied. The rate of oxygen mass transfer into a culture in a bioreactor is affected by operational conditions and geometrical parameters as well as the physicochemical properties of the medium (nutrients, substances excreted by the micro-organism, and surface active agents that are often added to the medium) and the presence of the micro-organism. Thus, oxygen mass transfer coefficient values in fermentation broths often differ substantially from values estimated for simple aqueous solutions. The influence of liquid phase physicochemical properties on kLa must be divided into the influence on k(L) and a, because they are affected in different ways. The presence of micro-organisms (cells, bacteria, or yeasts) can affect the mass transfer rate, and thus kLa values, due to the consumption of oxygen for both cell growth and metabolite production. In this work, theoretical equations for kLa prediction, developed for sparged and stirred tanks, taking into account the possible oxygen mass transfer enhancement due to the consumption by biochemical reactions, are proposed. The estimation of kLa is carried out taking into account a strong increase of viscosity broth, changes in surface tension and different oxygen uptake rates (OURs), and the biological enhancement factor, E, is also estimated. These different operational conditions and changes in several variables are performed using different systems and cultures (xanthan aqueous solutions, xanthan production cultures by Xanthomonas campestris, sophorolipids production by Candida bombicola, etc.). Experimental and theoretical results are presented and compared, with very good results.     

A novel centrifugal impeller bioreactor. II. Oxygen transfer and power consumption

The effects of the impeller configuration, aeration rate, and agitation speed on oxygen transfer coefficient K(L)a were studied in a newly designed centrifugal impeller bioreactor (5-L). The oxygen transfer rates in the novel bioreactor were also compared with those in a cell-lift bioreactor with comparable dimensions. The cell-lift impeller produced much higher surface oxygen transfer rates than the centrifugal one at an agitation speed over 200 rpm. This result was in good agreement with our observation that the cell-lift impeller produced much higher unfavorable turbulence. In addition, the experiments using granulated agar particles as pseudo plant cells indicated that the K(L)a value decreased steadily with an increase in agar particle concentration, and the centrifugal impeller still demonstrated a larger K(L)a than the cell lift up to a high pseudo cell concentration of 19.5 g dry weight (DW)/L (under 150 rpm and 0.20 vvm) or 22.3 g DW/L (under 200 rpm and 0.20 vvm). Furthermore, the correlation between power number and impeller Reynolds number for both the centrifugal and the cell-lift impellers was successfully obtained, which could be used for predicting the power input required by each impeller. From the results obtained, the centrifugal impeller bioreactor is expected to have great potential in its application to shear-sensitive biological systems.     

Gas transfer characteristics of a novel membrane bioreactor

We show the design features of a membrane bioreactor based on pulsatile flow across dimpled membranes. Results show an enhanced mass transfer of air of at least five-fold magnitude as compared with flat membranes. An increased working volume form 20 mL to 120 mL reduced the k(L)A at a given Reynolds number because of axial mixing of fluid from the deoxygenated end chamber. The bioreactor was used to supply air to a hybridoma mammalian cell line, and the calculated oxygen uptake showed that high-density cultures could be maintained in a 20mL, single-dimpled cultures could be maintained in a 20 mL, single-dimpled membrane system. Indirect aeration of a 2 L continuous stirred tank reactor, by a double-membrane system, showed that air could be supplied to mammalian cells at cell densities of approximately 4 x 10(6) /mL.     

Characterization of mixing in a novel wavy-walled bioreactor for tissue engineering

The wavy-walled bioreactor (WWB) possesses a novel geometry comprised of walls with sinusoidal waves that mimic baffles in an effort to promote mixing. This geometry provides a unique hydrodynamic environment suitable for the cultivation of mammalian cells and tissues and the investigation of fluid mechanical effects on cell and tissue growth and development. In the present study, mixing in WWB was characterized and compared to that in a conventional spinner flask (SF). The key parameters included in this characterization were mixing time, residence time distribution (RTD), and dissolved oxygen concentration during engineered cartilage tissue cultivation. Factors that influenced mixing in WWB included wave amplitude, agitation rate, and the ratio of the impeller diameter to the tank diameter (D/T). Data obtained from RTD and acid base neutralization studies confirmed the presence of different mixing zones in WWB. A theoretical comparison of WWB to a baffled spinner flask (BSF) using computational fluid dynamics (CFD) modeling predicted that while enhanced mixing was achieved in wavy-walled and BSF bioreactors, the shear stresses applied on tissue constructs were 15% lower in WWB. Improved mixing was achieved in WWB compared to the SF at similar D/T ratios, verified by improved oxygen transport and increased dispersion. However, for lower D/T ratios mixing in WWB was not necessarily improved. This study demonstrated the importance of characterization of mixing by showing the impact of even minor changes in bioreactor geometry and operating conditions.     

Characterization of gas-liquid mass transfer phenomena in microtiter plates

Gas-liquid mass transfer properties of shaken 96-well microtiter plates were characterized using a recently described method. The maximum oxygen transfer capacity (OTR(max)), the specific mass transfer area (a), and the mass transfer coefficient (k(L)) in a single well were determined at different shaking intensities (different shaking frequencies and shaking diameters at constant filling volume) and different filling volumes by means of sulfite oxidation as a chemical model system. The shape (round and square cross-sections) and the size (up to 2 mL maximum filling volume) of a microtiter plate well were also considered as influencing parameters. To get an indication of the hydrodynamic behavior of the liquid phase in a well, images were taken during shaking and the liquid height derived as a characteristic parameter. The investigations revealed that the OTR(max) is predominantly dependent on the specific mass transfer area (a) for the considered conditions in round-shaped wells. The mass transfer coefficient (k(L)) in round-shaped wells remains at a nearly constant value of about 0.2 m/h for all shaking intensities, thus within the range reported in the literature for surface-aerated bioreactors. The OTR(max) in round-shaped wells is strongly influenced by the interfacial tension, determined by the surface tension of the medium used and the surface properties of the well material. Up to a specific shaking intensity the liquid surface in the wells remains horizontal and no liquid movement can be observed. This critical shaking intensity must be exceeded to overcome the surface tension and, thus, to increase the liquid height and enlarge the specific mass transfer area. This behavior is solely specific to microtiter plates and has not yet been observed for larger shaking bioreactors such as shaking flasks. In square-shaped microtiter plate wells the corners act as baffles and cause a significant increase of OTR(max), a, and k(L). An OTR(max) of up to 0.15 mol/L/h can be reached in square-shaped wells.     

Mass transfer and hydrodynamic characteristics of unbaffled stirred bio-reactors: Influence of impeller design

Unbaffled stirred tanks are increasingly recognized as a viable alternative to common baffled tanks for a range of processes where the presence of baffles is undesirable for some reason. For instance, in the case of shear sensitive cell cultivation (e.g. human cells), unbaffled tanks have been recently found to be able to provide sufficient mass transfer through the free surface vortex. As a consequence the need for bubble formation and subsequent bursting, along with relevant cells damage, is conveniently avoided. In this work the influence of impeller geometry on mass transfer performance and power demand of an unbaffled stirred vessel operating both in sub-critical conditions (the free surface vortex has not yet reached the impeller) and in super-critical conditions (the free surface vortex has reached the impeller and a gas phase is ingested and dispersed inside the reactor) is presented.Experimental results show that the mass transfer performance of unbaffled systems is mainly affected by specific power consumption. Among the stirrer geometries investigated a simple PBT was found to provide the most interesting oxygen transfer performance in the sub-critical regime, and can therefore be regarded as a particularly suitable stirrer for shear sensitive cultures. As regards the super-critical regime, unbaffled tanks are found to provide a performance comparable with that of the standard (baffled) bioreactors, hence resulting in a viable alternative also for fermentations involving robust cells.     

Influence of Dissolved Oxygen Levels on Production of l-Asparaginase and Prodigiosin by Serratia marcescens

The effect of dissolved oxygen concentrations on the behavior of Serratia marcescens and on yields of asparaginase and prodigiosin produced in shaken cultures and in a 55-liter stainless-steel fermentor was studied. A range of oxygen transfer rates was obtained in 500-ml Erlenmeyer flasks by using internal, stainless-steel baffles and by varying the volume of medium per flask, and in the fermentor by high speed agitation (375 rev/min) or low rates of aeration (1.5 volumes of air per volume of broth per min), or both. Dissolved oxygen levels in the fermentation medium were measured with a membrane-type electrode. Peak yields of asparaginase were obtained in unbaffled flasks (3.0 to 3.8 IU/ml) and in the fermentor (2.7 IU/ml) when the level of dissolved oxygen in the culture medium reached zero. A low rate of oxygen transfer was accomplished by limited aeration. Production of prodigiosin required a supply of dissolved oxygen that was obtainable in baffled flasks with a high rate of oxygen transfer and in the fermentor with a combination of high-speed agitation and low-rate aeration. The fermentation proceeded at a more rapid rate and changes in pH and cell populations were accelerated by maintaining high levels of dissolved oxygen in the growth medium.     

Cephalosporin C production by immobilized Cephalosporium acremonium cells in a repeated batch tower bioreactor

The industrial production of antibiotics with filamentous fungi is usually carried out in conventional aerated and agitated tank fermentors. Highly viscous non-Newtonian broths are produced and a compromise must be found between convenient shear stress and adequate oxygen transfer. In this work, cephalosporin C production by bioparticles of immobilized cells of Cephalosporium acremonium ATCC 48272 was studied in a repeated batch tower bioreactor as an alternative to the conventional process. Also, gas-liquid oxygen transfer volumetric coefficients, k(L)a, were determined at various air flow-rates and alumina contents in the bioparticle. The bioparticles were composed of calcium alginate (2.0% w/w), alumina ( < 44 micra), cells, and water. A model describing the cell growth, cephalosporin C production, oxygen, glucose, and sucrose consumption was proposed. To describe the radial variation of oxygen concentration within the pellet, the reaction-diffusion model forecasting a dead core bioparticle was adopted. The k(L)a measurements with gel beads prepared with 0.0, 1.0, 1.5, and 2.0% alumina showed that a higher k(L)a value is attained with 1.5 and 2.0%. An expression relating this coefficient to particle density, liquid density, and air velocity was obtained and further utilized in the simulation of the proposed model. Batch, followed by repeated batch experiments, were accomplished by draining the spent medium, washing with saline solution, and pouring fresh medium into the bioreactor. Results showed that glucose is consumed very quickly, within 24 h, followed by sucrose consumption and cephalosporin C production. Higher productivities were attained during the second batch, as cell concentration was already high, resulting in rapid glucose consumption and an early derepression of cephalosporin C synthesizing enzymes. The model incorporated this improvement predicting higher cephalosporin C productivity.     

From field sampling to pneumatic bioreactor mycelia production of the ectomycorrhizal mushroom Laccaria trichodermophora

In order to increase survival rates of greenhouse seedlings destined for restoration and conservation programs, successful mycorrhization of the seedlings is necessary. To reforest forest ecosystems, host trees must be inoculated with ectomycorrhizal fungi and, in order to guarantee a sufficient supply of ectomycorrhizal inoculum, it is necessary to develop technologies for the mass production of ectomycorrhizal fungi mycelia. We selected the ectomycorrhizal fungus Laccaria trichodermophora, due to its ecological traits and feasible mycelia production in asymbiotic conditions. Here, we report the field sampling of genetic resources, as well as the highly productive nutritional media and cultivation parameters in solid cultures. Furthermore, in order to achieve high mycelial production, we used strain screening and evaluated pH, carbon source concentration, and culture conditions of submerged cultures in normal and baffled shake flasks. The higher productivity culture conditions in shake flasks were selected for evaluation in a pneumatic bioreactor, using modified BAF media with a 10 g/L glucose, pH 5.5, 25 °C, and a volumetric oxygen transfer coefficient (K_La) of 36 h⁻¹. Under those conditions less biomass (12–37 %) was produced in the pneumatic bioreactor compared with the baffled shake flasks. This approach shows that L. trichodermophora can generate a large biomass concentration and constitute the biotechnological foundation of its mycelia mass production.     

Physical and Biological Treatment of Oil-Contaminated Soil in a Baffled Roller Bioreactor

Physical and biological removal of diesel oil from contaminated soil was studied in a baffled roller bioreactor. Initially, the effects of four factors (soil loading, temperature, pH, and surfactant) on physical removal of diesel oil were investigated. Only the presence of a surfactant (sodium dodecyl sulfate [SDS]) demonstrated a significant effect on diesel oil removal. Diesel oil removal efficiency was increased from 32.0% to 63.9% in the presence of 100 mg/L SDS. Using a microbial culture enriched from contaminated soil, biological treatment of diesel oil polluted soil under different soil loadings (15% to 50%), different diesel oil concentrations (1 to 50 g/L), and different types of soil (sand, silt, and clay) was then investigated in the baffled roller bioreactor. Biodegradation consisted of both fast and slow stages for degradation of light and heavy compounds, respectively. All biodegradation experiments demonstrated significant decreases in diesel oil concentrations (88.3% in 14 days for initial diesel oil concentrations of 1000 mg/L and a wide range of soil loadings). The presence of silty or sandy soils enhanced the biodegradation rate compared to the control bioreactor (without soil). The sandy soil loading had no effect on the biodegradation results. Using the enriched culture, the baffled roller bioreactor was able to biodegrade high diesel concentrations (up to 50 g/L) with biodegradation rates of 112.2 and 39.3 mg/L· h during fast and slow stages, respectively.