Histomorphometric evaluation of bone ingrowth of porous titanium by a computer-assisted analyzing system]

The objective of this study was to evaluate the bone ingrowth of a new vacuum plasma sprayed titanium surface (vps-ti) in comparison to cs-titanium implants in a g?ttinger minipig model. Fifteen g?ttinger minipigs each received the two implants, vacuum plasma sprayed titanium with a porosity of 50% and a pore size of 200 microm (vps-ti) and an implant with a similar porosity but a different pore size 500 microm (cs-ti), at the proximal femur metaphysis by press-fit technique. The pigs were euthanized at three different postsurgical periods: 4, 8 and 12 weeks. Each femur was harvested and qualitative (macroscopic and microscopic) and quantitative (histomorphometric) histological analysis was done on histological slides. The results indicated that there was a difference in bone ingrowth between the two implants, whereas the bone ingrowth of vps-ti was superior to cs-ti after 4 and 8 weeks healing time. 12 weeks post implantationem no statistiscal difference was evident. The pore size of 200 microm seemed superior to a pore size of 500 microm. Whether or not these effects lead to a better mechanical stability remains unanswered.     

Similarity of bone ingrowth in rats and goats: a bone chamber study

Bone ingrowth has been studied extensively in rats by use of bone chambers. However, it is not known whether results in small animals, with respect to bone ingrowth processes, are similar in large animals, in which more realistic models are often used. Since the metabolic rate in small animals is, in general, higher than that in larger species, we hypothesized that bone ingrowth in chambers develops more rapidly in small animals. Therefore, identical bone chambers were placed in the tibias of rats and goats. After 6 and 12 weeks, histologic and histomorphometric examinations were carried out to measure bone and tissue ingrowth distances. Bone ingrowth was higher in both species at 12, compared with 6 weeks (P < 0.01). Tissue ingrowth in general (including soft tissue) was less in rats than in goats at both time periods (P < 0.001). However, bone ingrowth did not differ between species. Thus, when differences in size of an osseous defect are corrected for, there seems to be only little influence of differences in body size.     

Use of amine buffers for in vitro studies of bone resorption

Summary Responses of cultured fetal rat bones to parathyroid hormone (PTH) were compared in media gassed with 5% CO₂ and buffered with bicarbonate or in media buffered with the amine buffers HEPES (N-2-hydroxyethylpiperazine-N′-2-ethanesulfonic acid), TES (N-tris(hydroxymethyl)methyl-2-aminoethanesulfonic acid), PIPES (piperazine-N,N′-bis(2-ethanesulfonic acid)), Tris (tris(hydroxymethyl)aminomethane), or glycylglycine. PTH-induced bone resorption was markedly reduced in media buffered with the amine buffers and cultured in air in the absence of added bicarbonate. When the amine buffers were added to bicarbonate-buffered media, they decreased the responses of the bones to submaximal concentrations of PTH. But the response to supramaximal concentrations of PTH was usually not impaired. The results confirm our earlier studies indicating a CO₂ and/or bicarbonate requirement for optimal bone resorption. They also demonstrate that the amine buffers can inhibit the responses of bone to PTH even in the presence of CO₂ and bicarbonate. Supported by NIH research Grant #AM 11262. Supported by NIH Research Career Development Award #AM 70210.     

Use of the fluorescent antibody technique for the evaluation of Arthroderma uncinatum in soil

The fact that Arthroderma uncinatum can grow through soil has been demonstrated by the fluorescent antibody technique which appears to be a useful tool in investigating the ecology of keratin-decomposing fungi in the soil.     

Elastic properties of cancellous bone: measurement by an ultrasonic technique

The high degree of porosity of cancellous bone makes elastic property measurement difficult by traditional mechanical testing methods. An ultrasonic technique is described with which mechanical properties of anisotropic, rigid, porous materials, such as cancellous bone, can be measured. The technique utilizes unique piezoelectric transducers operated in a continuous wave mode at a frequency of approximately 50 kHz. Both longitudinal and shear waves can be propagated and received with the transducers allowing both Young's moduli and shear moduli to be determined with the technique. A comparison between moduli measured with the ultrasonic technique and moduli measured with traditional mechanical testing shows the new method to be quite accurate in elastic property determination, (r2 = 0.935, Emech = 1.00E1dt + 23.3 MPa) (r2 = 0.656, Gmech = 1.08 Gult--3.3MPa).     

A semi-automated in vitro gas production technique for ruminant feedstuff evaluation

This technical note describes the Reading Pressure Technique (RPT) – an in vitro feed evaluation system based on a semi-automated gas production technique. Substrates are incubated together with buffered rumen fluid in sealed fermentation flasks. A pressure transducer, interfaced with a PC allows accumulated head-space gas pressure values to be directly entered into a spreadsheet. These pressure measurements are then used to generate gas volume estimates using a quadratic function derived from simultaneous pressure and volume measurements. Earlier attempts to derive volume from pressure resulted in predicted volume being under estimated. This discrepancy was most likely due to diffusion of head-space gases into the liquid phase, a factor not considered in Boyle's Law, the initial relationship used. In comparison with the syringe technique (Theodorou et al., 1994), the modifications improved both the accuracy (reduced operator error) and rate at which measurements could be taken (5–6 s per flask) greatly increasing the analytical capacity (to 336 flasks or 75 substrates per incubation series). The ability of this system to provide information not just on both rate and extent of degradation, but also fermentation efficiency and degradation kinetics offers a wide variety of applications, for example the systematic evaluation of tropical feedstuffs. In conclusion it is suggested that the simplicity, low cost and high capacity of the RPT system make it ideal for those situations where either budget constraints or the level of technical expertise required render the more complex systems inappropriate.     

Fatigue evaluation of long cortical bone using ultrasonic guided waves

Bone fatigue fracture is a progressive disease due to stress concentration. This study aims to evaluate the long bone fatigue damage using the ultrasonic guided waves. Two-dimensional finite-difference time-domain method was employed to simulate the ultrasonic guided wave propagation in the long bone under different elastic modulus. The experiment was conducted on a 3.8 mm-thick bovine bone plate. The phase velocities of two fundamental guided modes, A1 and S1, were measured by using the axial transmission technique. Simulation shows that the phase velocities of guided modes A1 and S1 decrease with the increasing of the fatigue damage. After 20,000 cycles of fatigue loading on the bone plate, the average phase velocities of A1 and S1 modes were 6.6% and 5.3% respectively, lower than those of the intact bone. The study suggests that ultrasonic guided waves can be potentially used to evaluate the fatigue damage in long bones.     

Interstitial bone stress distributions accompanying ingrowth of a screen-like prosthesis anchorage layer

Recent development of screen-like bonded weaves of titanium wire for orthopaedic implant anchorage affords a unique opportunity for analytic studies of porous ingrowth micromechanics. The regular geometry of individual wires and the periodicity of the mesh weave are exploited in a series of two-dimensional finite element models, mapping interstitial bone stress fields as a function of ingrowth depth and wire size, shape, and spacing.

When the depth of bone ingrowth was less than one wire diameter, peak bone stresses always occurred at the leading (i.e. deepest) edge of bone ingrowth, immediately adjacent to the wire. As ingrowth depth approached a full wire diameter, peak local bone stresses were 2–9 times the nominal applied host bone stress, with greater stresses occurring for lower screen weave densities. Within multiple screen layers, the top layer consistently experienced the peak stress and transmitted most of the applied load, regardless of the number of underlying screen layers surrounded by bone. Neither wire size variations nor partial wire flattening substantially affected general trends in stress predictions.     

In vitro evaluation of natural marine sponge collagen as a scaffold for bone tissue engineering

The selection of a suitable scaffold matrix is critical for cell-based bone tissue engineering. This study aimed to identify and characterize natural marine sponges as potential bioscaffolds for osteogenesis. Callyspongiidae marine sponge samples were collected from the Fremantle coast of Western Australia. The sponge structure was assessed using scanning electron microscopy (SEM) and Hematoxylin and eosin. Mouse primary osteoblasts were seeded onto the sponge scaffold and immunostained with F-actin to assess cell attachment and aggregation. Alkaline phosphatase expression, von Kossa staining and real-time PCR were performed to examine the osteogenic potential of sponge samples. SEM revealed that the sponge skeleton possessed a collagenous fibrous network consisting of interconnecting channels and a porous structure that support cellular adhesion, aggregation and growth. The average pore size of the sponge skeleton was measured 100 to 300 μm in diameter. F-actin staining demonstrated that osteoblasts were able to anchor onto the surface of collagen fibres. Alkaline phosphatase expression, a marker of early osteoblast differentiation, was evident at 7 days although expression decreased steadily with long term culture. Using von Kossa staining, mineralisation nodules were evident after 21 days. Gene expression of osteoblast markers, osteocalcin and osteopontin, was also observed at 7, 14 and 21 days of culture. Together, these results suggest that the natural marine sponge is promising as a new scaffold for use in bone tissue engineering.     

Soft tissue movement and stress shielding do not affect bone ingrowth in the bone conduction chamber

A variety of bone chambers are used in orthopedic research to study bone and tissue ingrowth in small and large animals. If different bone chambers are placed in one species, differences in bone ingrowth are observed. For instance, bone ingrowth in the bone conduction chamber (BCC) is high, but is low or absent in the repeated sampling bone chamber (RSBC). This difference may be explained by the design and fixation of these chambers. It is known that stress shielding and micromovement can influence bone formation. The objective of the study reported here was to determine whether stress shielding or soft tissue movement affected bone ingrowth in the BCC in the goat. Two types of caps were made, with fixation similar to that of the fixation plate of the RSBC. By placing the caps over the BCCs and fixating the caps directly to the tibial bone, the effect of stress shielding was studied. One cap was in direct contact with the bone chamber underneath, the other cap did not touch the chamber. This difference was used to observe whether movement of the soft tissue on top of the chamber and cap would affect bone ingrowth. Each limb received one control chamber without a cap and a chamber with a cap, either with or without contacting the BCC, yielding four implants per goat. After 12 weeks, bone and total tissue ingrowths were measured. Bone ingrowth was seen in 38 of 40 chambers. Total tissue and bone ingrowths were comparable between control chambers and BCCs with a cap, irrespective of type. Neither stress shielding, nor lack of movement of soft tissue affected bone ingrowth. Other factors in the design of the chambers were responsible for the difference in bone ingrowth between the BCC and the RSBC.     

In vitro pharmacodynamic evaluation of antiviral medicinal plants using a vector-based assay technique

AIMS: Medicinal plants are increasingly being projected as suitable alternative sources of antiviral agents. The development of a suitable in vitro pharmacodynamic screening technique could contribute to rapid identification of potential bioactive plants and also to the standardization and/or pharmacokinetic-pharmacodynamic profiling of the bioactive components. METHODS AND RESULTS: Recombinant viral vectors (lentiviral, retroviral and adenoviral) transferring the firefly luciferase gene were constructed and the inhibition of viral vector infectivity by various concentrations of plant extracts was evaluated in HeLa or Hep2 cells by measuring the changes in luciferase activity. Cytotoxicity of the extracts was evaluated in parallel on HeLa or Hep2 cells stably expressing luciferase. Amongst the 15 extracts screened, only the methanol (ME) and the ethyl acetate (ET) fractions of the lichen, Ramalina farinacea specifically reduced lentiviral and adenoviral infectivity in a dose-dependent manner. Further, chromatographic fractionation of ET into four fractions (ET1-ET4) revealed only ET4 to be selectively antiviral with an IC50 in the 20 microg ml(-1) range. Preliminary mechanistic studies based on the addition of the extracts at different time points in the viral infection cycle (kinetic studies) revealed that the inhibitory activity was highest if extract and vectors were preincubated prior to infection, suggesting that early steps in the lentiviral or adenoviral replication cycle could be the major target of ET4. Inhibition of wild-type HIV-1 was also observed at a 10-fold lower concentration of the extract. CONCLUSIONS: The vector-based assay is a suitable in vitro pharmacodynamic evaluation technique for antiviral medicinal plants. The technique has successfully demonstrated the presence of antiviral principles in R. farinacea. SIGNIFICANCE AND IMPACT OF STUDY: Potential anti-HIV medicinal plants could rapidly be evaluated with the reported vector-based technique. The lichen, R. farinacea could represent a lead source of antiviral substances and is thus worthy of further studies.     

Influence of ingrowth regions on bone remodelling around a cementless hip resurfacing femoral implant

Hip resurfacing arthroplasty is an alternative to traditional hip replacement that can conserve proximal bone stock and has gained popularity but bone resorption may limit implant survival and remains a clinical concern. The goal of this study was to analyze bone remodelling patterns around an uncemented resurfacing implant and the influence of ingrowth regions on resorption. A computed tomography-derived finite element model of a proximal femur with a virtually implanted resurfacing component was simulated under peak walking loads. Bone ingrowth was simulated by six interface conditions: fully bonded; fully friction; bonded cap with friction stem; a small bonded region at the stem-cup intersection with the remaining surface friction; fully frictional, except for a bonded band along the distal end of the cap and superior half of the cap bonded with the rest frictional. Interface condition had a large influence on remodelling patterns. Bone resorption was minimized when no ingrowth occurred at the bone-implant interface. Bonding only the superior half of the cap increased bone resorption slightly but allowed for a large ingrowth region to improve secondary stability.     

Rib biopsy technique for cortical bone evaluation in rhesus monkeys (Macaca mulatta)

Old World primates are often studied to model human skeletal physiology. An important advantage of monkeys over other animal models (i.e., rodents) is the presence of cortical bone Haversian remodeling. Seventy-five female rhesus monkeys (Macaca mulatta) were subjected to bone biopsy. With monkeys in lateral decubitus position, the tenth rib was surgically exposed and freed from periosteum by use of careful sharp and blunt dissection. The rib section was resected, using bone cutters, and the surgical wound was closed. This procedure was repeated for the contralateral rib at a later time point in 65 monkeys. There was no mortality or appreciable morbidity. The bone specimens were (mean +/- SD) 2.50 +/- 0.25 cm long, with 5.5 +/- 1.0 mm2 total cross-sectional area. They were adequate for histologic, immunohistochemical, and quantitative histomorphometric examinations. Prevalence of pneumothorax was approximately 8.0% for the 140 procedures. This complication was immediately and successfully corrected by insertion of a small thoracic tube, evacuation of pneumothorax, and closure of the incision. This well-tolerated, repeatable procedure yields excellent specimens for performance of cortical bone histologic examination without euthanasia, allowing longitudinal evaluation.     

A contact model with ingrowth control for bone remodelling around cementless stems.

This work presents a computational model for bone remodelling around cementless stems. The problem is formulated as a material optimisation problem considering the bone and stem surfaces to be in contact. To emphasise the behaviour of the bone/stem interface, the computer model detects the existence of bone ingrowth during the remodelling; consequently, the contact conditions are changed for a better interface simulation. The trabecular bone is modelled as a strictly orthotropic material with equivalent properties computed by homogenisation. The distribution of bone relative density is obtained by the minimisation of a function that considers both the bone structural stiffness and the biological cost associated with metabolic maintenance of bone tissue. The situation of multiple load conditions is considered. The remodelling law, obtained from the necessary conditions for an optimum, is derived analytically from the optimisation problem and solved numerically using a suitable finite element mesh. The formulation is applied to an implanted femur. Results of bone density and ingrowth distribution are obtained for different coating conditions. Bone ingrowth does not occur over the entire coated surfaces. Indeed, we observed regions where separation or high relative displacement occurs that preclude bone ingrowth attachment. This prediction of the model is consistent with clinical observations of bone ingrowth. Thus, this model, which detect bone ingrowth and allow modification of the interface conditions, are useful for analysis of existing stems as well as design optimisation of coating extent and location on such stems.     

Reproducibility of a non-invasive ultrasonic technique of tendon force measurement,determined in vitro in equine superficial digital flexor tendons

A non-invasive ultrasonic (US) technique of tendon force measurement has been recently developed. It is based on the relationship demonstrated between the speed of sound (SOS) in a tendon and the traction force applied to it. The objectives of the present study were to evaluate the variability of this non-linear relationship among 7 equine superficial digital flexor (SDF) tendons, and the reproducibility of SOS measurements in these tendons over successive loading cycles and tests. Seven SDF tendons were equipped with an US probe (1 MHz), secured in contact with the skin overlying the tendon metacarpal part. The tendons were submitted to a traction test consisting in 5 cycles of loading/unloading between 50 and 4050 N. Four tendons out of the 7 were submitted to 5 additional cycles up to 5550 N. The SOS-tendon force relationships appeared similar in shape, although large differences in SOS levels were observed among the tendons. Reproducibility between cycles was evaluated from the root mean square of the standard deviations (RMS-SD) of SOS values observed every 100 N, and of force values every 2 m/s. Reproducibility of SOS measurements revealed high between successive cycles: above 500 N the RMS-SD was less than 2% of the corresponding traction force. Reproducibility between tests was lower, partly due to the experimental set-up; above 500 N the difference between the two tests stayed nevertheless below 15% of the corresponding mean traction force. The reproducibility of the US technique here demonstrated in vitro has now to be confirmed in vivo.     

Optical verification of a technique for in situ ultrasonic measurement of articular cartilage thickness

Several investigators have used pulse-echo ultrasonics to measure the thickness of articular cartilage in situ. The underlying assumption in all measurements was that the second reflection used in thickness calculations was from the calcified-cartilage/cartilage boundary (tidemark). To investigate this assumption, the thickness of 24 cartilage plugs excised from a human femoral head was measured both ultrasonically and optically. Measurements established that the second reflection was from the tidemark and validated the ultrasonic technique as a method of mapping the thickness distribution of articular cartilage in synovial joints in situ.