Extractive acetonobutylic fermentation by coupling ultrafiltration and distillation

An extractive acetonobutylic fermentation process is developed by integrating bioproduction, Ultrafiltration, and distillation, providing simultaneous retention of biomass, selective removal of inhibitors from the permeate, as well as separation and purification of acetone-butanol-ethanol solvents. Successive batch fermentations were performed with normal pressure distillation (98 degrees C), which permitted prolonging and enhancing (by a factor of 3) solvent production, with very few volume exchanges of medium (average dilution rate ws 0.002 h(-1)), and recovering on-line concentrated solvents. Different operating conditions were also tested in order to study the presence of extracellular autolytic enzymes as inhibition factors: It was shown that, (1) extracellular autolytic activity remains low during the larger part of fermentations, even without enzyme-inactivating thermotreatment in the distillation boiler, and (2) high-temperature distillation causes deleterious effects to the culture medium for long duration treatments. Progressive improvements of the process were achieved, first, by managing continuous runs, providing a minimum renewal of the culture medium and, mainly, by decreasing temperature and pressure of distilation. Solvent productivity then reached 2.6 g/L h for a 0.036 h(-1) average dilution rate, corresponding to a feed concentration of 156 g/L glucose actually consumed.     

A Mathematical model for ethanol production by extractive fermentation in a continuous stirred tank fermentor

Extractive fermentation is a technique that can be used to reduce the effect of end product inhibition through the use of a water-immiscible phase that removes fermentation products in situ. This has the beneficial effect of not only removing inhibitory products as they are formed (thus keeping reaction rates high) but also has the potential for reducing product recovery costs. We have chosen to examine the ethanol fermentation as a model system for end product inhibition and extractive fermentation and have developed a computer model predicting the productivity enhancement possible with this technique together with other key parameters such as extraction efficiency and residual glucose concentration. The model accommodates variable liquid flowrates entering and leaving the system, since it was found that the aqueous outlet flowrate could be up to 35% lower than the inlet flowrate during extractive fermentation of concentrated glucose feeds due to the continuous removal of ethanol from the fermentation broth by solvent extraction. The model predicts a total ethanol productivity of 82.6 g/L h if a glucose feed of 750 g/L is fermented with a solvent having a distribution coefficient of 0.5 at a solvent dilution rate of 5.0 h(-1). This is more than 10 times higher than for a conventional chemostat fermentation of a 250 g/L glucose feed. The model has furthermore illustrated the possible trade-offs that exist between obtaining a high extraction efficiency and a low residual glucose concentration.     

Extractive fermentation for butyric acid production from glucose by Clostridium tyrobutyricum

A novel extractive fermentation for butyric acid production from glucose, using immobilized cells of Clostridium tyrobutyricum in a fibrous bed bioreactor, was developed by using 10% (v/v) Alamine 336 in oleyl alcohol as the extractant contained in a hollow-fiber membrane extractor for selective removal of butyric acid from the fermentation broth. The extractant was simultaneously regenerated by stripping with NaOH in a second membrane extractor. The fermentation pH was self-regulated by a balance between acid production and removal by extraction, and was kept at approximately pH 5.5 throughout the study. Compared with conventional fermentation, extractive fermentation resulted in a much higher product concentration (>300 g/L) and product purity (91%). It also resulted in higher reactor productivity (7.37 g/L. h) and butyric acid yield (0.45 g/g). Without on-line extraction to remove the acid products, at the optimal pH of 6.0, the final butyric acid concentration was only approximately 43.4 g/L, butyric acid yield was 0.423 g/g, and reactor productivity was 6.77 g/L. h. These values were much lower at pH 5.5: 20.4 g/L, 0.38 g/g, and 5.11 g/L. h, respectively. The improved performance for extractive fermentation can be attributed to the reduced product inhibition by selective removal of butyric acid from the fermentation broth. The solvent was found to be toxic to free cells in suspension, but not harmful to cells immobilized in the fibrous bed. The process was stable and provided consistent long-term performance for the entire 2-week period of study.     

Acetone-butanol-ethanol fermentation and isoflavone extraction using kudzu roots

The economics of Acetone-butanol-ethanol (ABE) fermentation is greatly affected by raw materials, and the use of readily available starchy materials from marginal farming lands could be a viable option for reducing costs. Kudzu, a rapidly growing perennial leguminous vine, has been planted on marginal farming land and widely distributed in Asia and America. This study investigated ABE fermentation by C. acetobutylicum ATCC 824 using kudzu roots and isoflavone extraction from kudzu fermentation residue (KFR). The kudzu roots could be used as a sole substrate for ABE fermentation without nutritional supplements. Batch culture containing 140 g kudzu/L produced 17.99 ± 1.08 g/L solvent (ABE), including 11.20 ± 0.79 g/L butanol, 5.54 ± 0.20 g/L acetone, and 1.15 ± 0.09 g/L ethanol, with a productivity of 0.19 g/(L/h) and a yield of 0.33 g solvent/g sugar after 96 h of fermentation. Isoflavone yield extracted from KFR was 1.90/100 g KFR, approximately 48% higher compared with that extracted from raw kudzu. A kinetic analysis of the extraction process showed that both the isoflavone yield and the extraction rate obtained from KFR were higher than the corresponding values obtained from raw kudzu. These results indicate that kudzu may provide a new potential raw material for ABE production and the process of ABE fermentation integrated with isoflavone extraction may provide a new way to reduce fermentable substrate costs.     

Ethanol from whey: Continuous fermentation with cell recycle

The production of ethanol from cheese whey lactose has been demonstrated using a single-stage continuous culture fermentation with 100% cell recycle. In a two-step process, an aerobic fed batch operation was used initially to allow biomass buildup in the absence of inhibitory ethanol concentrations. In the anaerobic ethanol-producing second step, a strain of Kluyveromyces fragilis selected on the basis of batch fermentation data had a maximum productivity of 7.1 g ethanol/L/h at a dilution rate of 0.15 h(-1), while achieving the goal of zero residual sugar concentration. The fermentation productivity diminished when the feed sugar concentation exceeded 120 g/L despite the inclusion of a lipid mixture previous shown to enhance batch fermentation productivities.     

NADH fluorscence in a carbon-limited fermentation

The continuous flow acetone-butanol fermentation conducted at lowered inlet feed sugar concentrations and at a constant dilution rate D =0.075 h(-1) demonstrated a significant decreases in the availability of the cell population "reduction energy" (F/X), resulting in an exclusive accumulation of intermediate acids under those conditions. The cultures resumed its solvent production activity when the inlet sugar concentration in the feed stream was increased from 20 to 40 g/L at the same low growth/dilution rates. A linear correlation between the culture reduction content (F/X) and the specific butanol rate (q(B)) was observed under the present conditions, indicating the necessity of the NADH availability for the increased solvent production.     

一株拜氏梭菌利用甘蔗废糖蜜发酵生产丙酮丁醇

以甘蔗废糖蜜作为原料,利用Clostridium beijerinckii DSM 6422菌株进行丙酮丁醇发酵的初步研究.结果表明:采用H2SO4预处理糖蜜,初糖质量浓度60 g/L,(NH4)2SO4 2g/L,CaCO3 10 g/L,温度30℃,pH 5.5～7.0,接种量6％(体积分数),在5L发酵罐中发酵培养96 h,总溶剂产量为16.17 g/L,其中丁醇质量浓度为10.07 g/L,总溶剂产率为30.2％,糖利用率为89.3％.     

Enhanced acetone-butanol fermentation using repeated fed-batch operation coupled with cell recycle by membrane and simultaneous removal of inhibitory products by adsorption

A novel acetone-butanol production process was developed which integrates a repeated fed-batch fermentation with continuous product removal and cell recycle. The inhibitory product concentrations of the fermentation by Clostridium acetobutylicum were reduced by the simultaneous extraction process using polyvinylpyridine (PVP) as an adsorbent. Because of the reduced inhibition effect, a higher specific cell growth rate and thus a higher product formation rate was achieved. The cell recycle using membrane separation increased the total cell mass density and, therefore, enhanced the reactor productivity. The repeated fed-batchoperation overcame the drawbacks typically associated with a batch operation such as down times, long lag period, and the limitation on the maximum initial substrate concentration allowed due to the substrate inhibition. Unlike a continuous operation, the repeated fed-batch operation could beoperated for a long time at a relatively higher substrate concentration without sacrificing the substrate loss in the effluent. As a result, the integrated process reached 47.2 g/L in the equivalent solvent concentration (including acetone, butanol, and ethanol) and 1.69 g/L . h in the fermentor productivity, on average, over a 239.5-h period. Compared with a controlled traditional batch acetone-butanol fermentation, the equivalent solvent concentration and the tormentor productivity were increased by 140% and 320%, respectively. (c) 1995 John Wiley & Sons Inc.     

Continuous acetone-butanol-ethanol (ABE) fermentation using immobilized cells of Clostridium acetobutylicum in a packed bed reactor and integration with product removal by pervaporation

An integrated solvent (ABE) fermentation and product removal process was investigated. A stable solvent productivity of 3.5 g/L h was achieved by using cells of Clostridium acetobutylicum immobilized onto a packed bed of bonechar, coupled with continuous product removal by pervaporation. Using a concentrated feed solution containing lactose at 130g/L, a lactose value of 97.9% was observed. The integrated fermentation and product removal system, with recycling of the treated fermentor effluent containing only low amount of solvents (/but lactose and acids), leads to only low acid losses. Therefore, most of the acids are converted to solvents, and this results in a high solvent yield of 0.39 g solvents/g lactose utilized. The pervaporation system provided a high product removal rate even at low solvent concentrations. A solvent membrane flux of 7.1 g/m(2) h with a selectivity of 5 was achieved during these investigations. The system proved to be very reliable.     

Bacterial cellulose production by fed-batch fermentation in molasses medium

Batch and fed-batch fermentations for bacterial cellulose (BC) production using molasses as a carbon source by Acetobacter xylinum BPR2001 were carried out in a jar fermentor. For improvement of BC production, molasses was subjected to H2SO4-heat treatment. The maximum BC concentration by this treated molasses increased 76%, and the specific growth rate increased 2-fold compared with that by untreated molasses. In batch fermentation, when the initial sugar concentrations of H2SO4-heat-treated molasses were varied from 20 to 70 g/L, the highest value of maximum BC concentration of 5.3 g/L was observed at 20 g/L. BC production in intermittent fed-batch (IFB) fermentation was conducted referring to the data in batch fermentation, and the highest BC production of 7.82 g/L was obtained when 0.2 L of molasses medium was added five times. When continuous fed-batch (CFB) fermentations were conducted, maximum BC concentration was obtained with a feeding rate of 6.3 g-sugar/h, which was derived from the optimal IFB experiment.     

无载体固定化酵母细胞木薯淀粉质原料酒精连续发酵研究

以木薯粉糖化液为发酵底物,在总发酵体积(有效)为15L的悬浮床生物反应器中,对一株粟酒裂殖酵母变异株进行一级和二级连续发酵研究。结果表明,二级连续发酵系统可明显改善一级系统的不足,并取得了平均流加糖液浓度150g/L,发酵强度为97g/L.h,流出液酒精浓度727g/L,残糖浓度374g./L,总糖利用率达90%的较好结果;整个系统在连续一个月的运行中从未发现染菌现象,发酵操作稳定。     

Simultaneous single-cell protein production and COD removal with characterization of residual protein and intermediate metabolites during whey fermentation by K. marxianus

Cheese whey fermentation with Kluyveromyces marxianus was carried out at 40 °C and pH 3.5 to examine simultaneous single-cell protein production and chemical oxygen demand (COD) removal, determine the fate of soluble whey protein and characterize intermediate metabolites. After 36 h of batch fermentation, the biomass concentration increased from 2.0 to 6.0 g/L with 55 % COD reduction (including protein), whereas soluble whey protein concentration decreased from 5.6 to 4.1 g/L. It was confirmed through electrophoresis (SDS-PAGE) that the fermented whey protein was different from native whey protein. HPLC and GC–MS analysis revealed a change in composition of organic compounds post-fermentation. High inoculum concentration in batch fermentation resulted in an increase in biomass concentration from 10.3 to 15.9 g/L with 80 % COD reduction (including protein) within 36 h with residual protein concentration of 4.5 g/L. In third batch fermentation, the biomass concentration increased from 7.3 to 12.4 g/L with 71 % of COD removal and residual protein concentration of 4.3 g/L after 22 h. After 22 h, the batch process was shifted to a continuous process with cell recycle, and the steady state was achieved after another 60 h with biomass yield of 0.19 g biomass/g lactose and productivity of 0.26 g/L h. COD removal efficiency was 78–79 % with residual protein concentration of 3.8–4.2 g/L. The aerobic continuous fermentation process with cell recycle could be applied to single-cell protein production with substantial COD removal at low pH and high temperature from cheese whey.     

Membrane-integrated fermentation system for improving the optical purity of D-lactic acid produced during continuous fermentation

This report describes the production of highly optically pure D-lactic acid by the continuous fermentation of Sporolactobacillus laevolacticus and S. inulinus, using a membrane-integrated fermentation (MFR) system. The optical purity of D-lactic acid produced by the continuous fermentation system was greater than that produced by batch fermentation; the maximum value for the optical purity of D-lactic acid reached 99.8% enantiomeric excess by continuous fermentation when S. leavolacticus was used. The volumetric productivity of the optically pure D-lactic acid was about 12 g/L/h, this being approximately 11-fold higher than that obtained by batch fermentation. An enzymatic analysis indicated that both S. laevolacticus and S. inulinus could convert L-lactic acid to D-lactic acid by isomerization after the late-log phase. These results provide evidence for an effective bio-process to produce D-lactic acid of greater optical purity than has conventionally been achieved to date.     

Performance of batch, fed-batch, and continuous A-B-E fermentation with pH-control

Batch, fed-batch, and continuous A-B-E fermentations were conducted and compared with pH controlled at 4.5, the optimal range for solvent production. While the batch mode provides the highest solvent yield, the continuous mode was preferred in terms of butanol yield and productivity. The highest butanol yield and productivity found in the continuous fermentation at dilution rate of 0.1 h⁻¹ were 0.21 g-butanol/g-glucose and 0.81 g/L/h, respectively. In the continuous and fed-batch fermentation, the time needed for passing acidogenesis to solventogenesis was an intrinsic hindrance to higher butanol productivity. Therefore, a low dilution rate is suggested for the continuous A-B-E fermentation, while the fed-batch mode is not suggested for solvent production. While 3:6:1 ratio of acetone, butanol, and ethanol is commonly observed from A-B-E batch fermentation by Clostridium acetobutylicum when the pH is uncontrolled, up to 94% of the produced solvent was butanol in the chemostat with pH controlled at 4.5.     

Acetone-butanol-ethanol (ABE) fermentation in an immobilized cell trickle bed reactor

Acetone-butanol-ethanol (ABE) fermentation was successfully carried out in an immobilized cell trickle bed reactor. The reactor was composed of two serial columns packed with Clostridium acetobutylicum ATCC 824 entrapped on the surface of natural sponge segments at a cell loading in the range of 2.03-5.56 g dry cells/g sponge. The average cell loading was 3.58 g dry cells/g sponge. Batch experiments indicated that a critical pH above 4.2 is necessary for the initiation of cell growth. One of the media used during continuous experiments consisted of a salt mixture alone and the other a nutrient medium containing a salt mixture with yeast extract and peptone. Effluent pH was controlled by supplying various fractions of the two different types of media. A nutrient medium fraction above 0.6 was crucial for successful fermentation in a trickle bed reactor. The nutrient medium fraction is the ratio of the volume of the nutrient medium to the total volume of nutrient plus salt medium. Supplying nutrient medium to both columns continuously was an effective way to meet both pH and nutrient requirement. A 257-mL reactor could ferment 45 g/L glucose from an initial concentration of 60 g/L glucose at a rate of 70 mL/h. Butanol, acetone, and ethanol concentrations were 8.82, 5.22, and 1.45 g/L, respectively, with a butanol and total solvent yield of 19.4 and 34.1 wt %. Solvent productivity in an immobilized cell trickle bed reactor was 4.2 g/L h, which was 10 times higher than that obtained in a batch fermentation using free cells and 2.76 times higher than that of an immobilized CSTR. If the nutrient medium fraction was below 0.6 and the pH was below 4.2, the system degenerated. Oxygen also contributed to the system degeneration. Upon degeneration, glucose consumption and solvent yield decreased to 30.9 g/L and 23.0 wt %, respectively. The yield of total liquid product (40.0 wt %) and butanol selectivity (60.0 wt %) remained almost constant. Once the cells were degenerated, they could not be recovered.     

分批补料对木糖发酵生产乙醇的影响

以树干毕赤酵母为发酵菌种,纯木糖为发酵底物,通过分批补料来提高糖利用率以及乙醇得率。结果表明,在24h内,最佳初始木糖浓度为80g/L,在28h的发酵周期中,可以将木糖浓度提高至90g/L,在32h发酵周期内可以将木糖浓度提高至100g/L。通过分批补料,乙醇浓度得到明显提高。当总糖浓度分别为80g/L、90g/L时,24h发酵周期内,分批补料次数以1次为宜,乙醇浓度分别达30.95g/L、32.60g/L,相比于不补料即一次性投料,乙醇浓度分别提高了9.36%、9.18%。总糖浓度100g/L,28h发酵周期内,补料2次效果最佳,乙醇浓度达37.49g/L,比一次性投料下提高了10.36%,较一次性投料达到相同发酵效果缩短了4h。     

Performance comparison of ethanol and butanol production in a continuous and closed-circulating fermentation system with membrane bioreactor

Since both ethanol and butanol fermentations are urgently developed processes with the biofuel-demand increasing, performance comparison of aerobic ethanol fermentation and anerobic butanol fermentation in a continuous and closed-circulating fermentation (CCCF) system was necessary to achieve their fermentation characteristics and further optimize the fermentation process. Fermentation and pervaporation parameters including the average cell concentration, glucose consumption rate, cumulated production concentration, product flux, and separation factor of ethanol fermentation were 11.45?g/L, 3.70?g/L/h, 655.83?g/L, 378.5?g/m²/h, and 4.83, respectively, the corresponding parameters of butanol fermentation were 2.19?g/L, 0.61?g/L/h, 28.03?g/L, 58.56?g/m²/h, and 10.62, respectively. Profiles of fermentation and pervaporation parameters indicated that the intensity and efficiency of ethanol fermentation was higher than butanol fermentation, but the stability of butanol fermentation was superior to ethanol fermentation. Although the two fermentation processes had different features, the performance indicated the application prospect of both ethanol and butanol production by the CCCF system.     

Design and evaluation of a continuous semipartition bioreactor for in situ liquid‐liquid extractive fermentation

Extractive fermentation (or in situ product removal (ISPR)) is an operational method used to combat product inhibition in fermentations. To achieve ISPR, different separation techniques, modes of operation and physical reactor configurations have been proposed. However, the relative paucity of industrial application necessitates continued investigation into reactor systems. This article outlines a bioreactor designed to facilitate in situ product extraction and recovery, through adapting the reaction volume to include a settler and solvent extraction and recycle section. This semipartition bioreactor is proposed as a new mode of operation for continuous liquid‐liquid extractive fermentation. The design is demonstrated as a modified bench‐top fermentation vessel, initially analysed in terms of fluid dynamic studies, in a model two‐liquid phase system. A continuous abiotic simulation of lactic acid (LA) fermentation is then demonstrated. The results show that mixing in the main reaction vessel is unaffected by the inserted settling zone, and that the size of the settling tube effects the maximum volumetric removal rate. In these tests the largest settling tube gave a potential continuous volumetric removal rate of 7.63 ml/min; sufficiently large to allow for continuous product extraction even in a highly productive fermentation. To demonstrate the applicability of the developed reactor, an abiotic simulation of a LA fermentation was performed. LA was added to reactor continuously at a rate of 33ml/h, while continuous in situ extraction removed the LA using 15% trioctylamine in oleyl alcohol. The reactor showed stable LA concentration of 1 g/L, with the balance of the LA successfully extracted and recovered using back extraction. This study demonstrates a potentially useful physical configuration for continuous in situ extraction.     

Ethanol fermentation in a magnetically fluidized bed reactor with immobilized Saccharomyces cerevisiae in magnetic particles

Ethanol fermentation by immobilized Saccharomyces cerevisiae cells in magnetic particles was successfully carried out in a magnetically stabilized fluidized bed reactor (MSFBR). These immobilized magnetic particles solidified in a 2 % CaCl(2) solution were stable and had high ethanol fermentation activity. The performance of ethanol fermentation of glucose in the MSFBR was affected by initial particle loading rate, feed sugar concentration and dilution rate. The ethanol theoretical yield, productivity and concentration reached 95.3%, 26.7 g/L h and 66 g/L, respectively, at a particle loading rate of 41% and a feed dilution rate of 0.4 h(-1) with a glucose concentration of 150 g/L when the magnetic field intensity was kept in the range of 85-120 Oe. In order to use this developed MSFBR system for ethanol production from cheap raw materials, cane molasses was used as the main fermentation substrate for continuous ethanol fermentation with the immobilized S. cerevisiae cells in the reactor system. Molasses gave comparative ethanol productivity in comparison with glucose in the MSFBR, and the higher ethanol production was observed in the MSFBR than in a fluidized bed reactor (FBR) without a magnetic field.     

铁改性沸石对Clostridium acetobutylicum XY16固定效率及发酵性能的影响

考察4种无机铁盐改性沸石对丁醇生产菌Clostridium acetobutylicum XY16的固定效率及其发酵产丁醇性能的影响。结果表明:铁改性沸石对菌体的固定效率均优于未改性沸石,而Fe3+改性效果优于Fe2+,经FeCl3改性的沸石对菌体具有良好的吸附作用,当Fe3+-zeolite用量为180 g/L时,细胞的固定效率达到87%。在此基础上,比较了沸石负载的铁离子量对丁醇发酵性能的影响,沸石负载的铁离子量为6.0 mg/g时可显著提高丁醇发酵性能,当葡萄糖质量浓度为60 g/L时进行发酵,丁醇产量为13.5 g/L,总溶剂可达20 g/L,总溶剂的生产速率为0.385g/(L.h),比游离细胞发酵分别提高了9.5%、10.3%和40%。