Citric acid and maleic anhydride as compatibilizers in starch/poly(butylene adipate-co-terephthalate) blends by one-step reactive extrusion

Starch/poly(butylene adipate-co-terephthalate) films were obtained by one-step reactive extrusion using maleic anhydride (MA) and citric acid (CA) as compatibilizers. The mechanical, structural, optical and barrier properties of the films were analyzed when glycerol (GLY), CA and MA were added to the starch/PBAT (55:45, w/w) according to mixture design. FTIR analysis showed that CA and MA were able to promote esterification/transesterification reactions and that CA induced them more efficiently. When a greater proportion of compatibilizer (1.5 wt%) was used, the resulting films were more opaque and had a greater tensile strength. A greater proportion of GLY (10.0%, w/w) improved the elongation at the break of the films. The barrier properties to water vapor of the films were improved by high levels of CA (1.5 wt%) and intermediate levels of GLY (9.25 wt%). The inclusion of compatibilizers resulted in blends with improved properties, representing a potential replacement for non-biodegradable films.     

Mechanical and water barrier properties of starch/PVA composite films by adding nano-sized poly(methyl methacrylate-co-acrylamide) particles

The aim of this work is to prepare starch/PVA composite films added nano-sized poly(methyl methacrylate-co-acrylamide) (PMMA-co-AAm) particles and to investigate the mechanical properties, water barrier properties, and soil burial degradation for the films. Composite films were prepared by using corn starch, polyvinyl alcohol (PVA), nano-sized PMMA-co-AAm particles, and additives, i.e., glycerol (GL), xylitol (XL), and citric acid (CA). Nano-sized PMMA-co-AAm particles were synthesized by emulsion polymerization. The results of the evaluation of properties for prepared films indicated that compared with films without PMMA-co-AAm particles, the mechanical properties and water resistance were improved up to 70-400% by the addition of nano-sized PMMA-co-AAm. In addition, the results of the soil burial biodegradation revealed that films added PMMA-co-AAm particles were degraded by about 45-65% after 165 days.     

角质酶在生物可降解聚酯聚己二酸/对苯二甲酸丁二醇酯降解中的应用

随着废弃塑料带来的环境污染越来越严重,生物可降解聚酯已成为大众关注的焦点。聚己二酸/对苯二甲酸丁二醇酯[poly(butylene adipate-co-terephthalate),PBAT]是脂肪族和芳香族共聚形成的生物可降解聚酯,兼具两者的优异性能。针对PBAT在自然条件下对降解环境要求严格且降解周期长的不足之处,本研究探究了角质酶在PBAT降解中的应用和对苯二甲酸-丁二醇酯(butylene terephthalate,BT)含量对PBAT生物降解性的影响,以实现对PBAT降解速率的提升。选取5种不同来源的聚酯降解酶对PBAT进行降解应用并比较出降解效果最优的酶,并测定了含有不同BT含量的PBAT聚酯的降解效率。结果表明,角质酶ICCG为降解效果最好的酶,且BT含量越高PBAT的降解率越低。此外,还确定了角质酶ICCG对高BT含量的PBAT(H)降解的最适温度、最适缓冲液类型、最适pH、最适E/S(enzyme to substrate)和最适底物浓度比分别为75℃、Tris-HCl、9.0、0.4%和1.0%。本研究结果可为角质酶在PBAT降解中的应用提供一定的理论依据和实验...     

Study of biodegradable polylactide/poly(butylene adipate-co-terephthalate) blends

Both polylactide (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable polymers. They are thermoplastics which can be processed using most conventional polymer processing methods. PLA is high in strength and modulus (63 MPa and 3.4 GPa, respectively) but brittle (strain at break 3.8%) while PBAT is flexible and tough (strain at break approximately 710%). In view of their complementary properties, blending PLA with PBAT becomes a natural choice to improve PLA properties without compromising its biodegradability. In this study, PLA and PBAT were melt blended using a twin screw extruder. Melt elasticity and viscosity of the blends increased with the concentration of PBAT. Crystallization of the PLA component, phase morphology of the blend, mechanical properties, and toughening mechanism were investigated. The blend comprised an immiscible, two-phase system with the PBAT evenly dispersed in the form of approximately 300 nm domains within the PLA matrix. The PBAT component accelerated the crystallization rate of PLA but had little effect on its final degree of crystallinity. With the increase in PBAT content (5-20 wt %), the blend showed decreased tensile strength and modulus; however, elongation and toughness were dramatically increased. With the addition of PBAT, the failure mode changed from brittle fracture of the neat PLA to ductile fracture of the blend as demonstrated by tensile test and scanning electron microcopy (SEM) micrographs. Debonding between the PLA and PBAT domains induced large plastic deformation in PLA matrix ligaments.     

Films of starch and poly(butylene adipate co-terephthalate) added of soybean oil (SO) and Tween 80

Starch extruded in the presence of a plasticizer results in a material called thermoplastic starch (TPS). TPS mixed with poly(butylene adipate co-terephthalate) (PBAT), soybean oil (SO), and surfactant may result in films with improved mechanical properties due to greater hydrophobicity and compatibility among the polymers. This study characterized films produced from blends containing 65% TPS and 35% PBAT with SO added as compatibilizer. The Tween 80 was added to prevention of phase separation. The elongation and resistance were greater in the films with SO. The infrared spectra confirmed an increase in ester groups bonded to the PBAT and the presence of groups bonded to the starch ring, indicating TPS-SO and PBAT-SO interactions. The micrographs suggest that the films with SO were more homogenous. Thus, SO is considered to be a good compatibilizer for blends of TPS and PBAT.     

Biodegradability and mechanical properties of starch films from Andean crops

Different Andean crops were used to obtain starches not previously reported in literature as raw material for the production of biodegradable polymers. The twelve starches obtained were used to prepare biodegradable films by casting. Water and glycerol were used as plasticizers. The mechanical properties of the starch based films were assessed by means of tensile tests. Compost tests and FTIR tests were carried out to assess biodegradability of films. The results show that the mechanical properties (UTS, Young's modulus and elongation at break) of starch based films strongly depend on the starch source used for their production. We found that all the starch films prepared biodegrade following a three stage process and that the weight loss rate of all the starch based films tested was higher than the weight loss rate of the cellulose film used as control.     

Microbial degradation of aliphatic and aliphatic-aromatic co-polyesters

Biodegradable plastics (BPs) have attracted much attention since more than a decade because they can easily be degraded by microorganisms in the environment. The development of aliphatic-aromatic co-polyesters has combined excellent mechanical properties with biodegradability and an ideal replacement for the conventional nondegradable thermoplastics. The microorganisms degrading these polyesters are widely distributed in various environments. Although various aliphatic, aromatic, and aliphatic-aromatic co-polyester-degrading microorganisms and their enzymes have been studied and characterized, there are still many groups of microorganisms and enzymes with varying properties awaiting various applications. In this review, we have reported some new microorganisms and their enzymes which could degrade various aliphatic, aromatic, as well as aliphatic-aromatic co-polyesters like poly(butylene succinate) (PBS), poly(butylene succinate)-co-(butylene adipate) (PBSA), poly(ε-caprolactone) (PCL), poly(ethylene succinate) (PES), poly(l-lactic acid) (PLA), poly(3-hydroxybutyrate) and poly(3-hydoxybutyrate-co-3-hydroxyvalterate) (PHB/PHBV), poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly(butylene adipate-co-terephthalate (PBAT), poly(butylene succinate-co-terephthalate) (PBST), and poly(butylene succinate/terephthalate/isophthalate)-co-(lactate) (PBSTIL). The mechanism of degradation of aliphatic as well as aliphatic-aromatic co-polyesters has also been discussed. The degradation ability of microorganisms against various polyesters might be useful for the treatment and recycling of biodegradable wastes or bioremediation of the polyester-contaminated environments.     

Biodegradability and mechanical properties of polycaprolactone composites encapsulating phosphate-solubilizing bacterium Bacillus sp. PG01

This study examined the feasibility of using polycaprolactone (PCL) and its composites (with starch and/or clay) in encapsulating cells of phosphate-solubilizing bacteria (PSB) for the development of biodegradable and “controlled-release” bacterial fertilizer. The PSB used in this work was an indigenous Bacillus sp. PG01 isolate. The results show that the PG01 strain was able to degrade all the cell-loaded capsules made of PCL and PCL composites, resulting in a continual cell release. Morphology observation indicates that severe disruption of the capsule structure occurred after incubation for 15–20 days. The biodegradability of the capsules decreased in the order of PCL/starch (20 wt%) > PCL/starch (20 wt%)/cay (7 wt%) > PCL alone > PCL/clay (7 wt%). Similar trends were also observed for the decrease in tensile strength and elongation at break, suggesting strong connections between biodegradability and the mechanical properties. Addition of starch appeared to enhance the biodegradability of the capsules, whereas the clay-blended composites were less biodegradable. The amount and rate of cell release from cell-encapsulated PCL-based capsules were positively dependent on the biodegradability and on the decrease in the mechanical strength. Nevertheless, the pattern of cell release was quite similar for all types of capsules. The outcome of this work seems to suggest that by proper manipulation of composite compositions, the controlled release of the bacterial fertilizer (i.e., Bacillus sp. PG01 cells) might be achievable.     

Multifunctional polyelectrolyte multilayer films: combining mechanical resistance, biodegradability, and bioactivity

Cross-linked polyelectrolyte multilayer films (CL PEM) have an increased rigidity and are mechanically more resistant than native (e.g., uncrosslinked) films. However, they are still biodegradable, which make them interesting candidates for biomedical applications. In this study, CL PEM films have been explored for their multifunctional properties as (i) mechanically resistant, (ii) biodegradable, and (iii) bioactive films. Toward this end, we investigated drug loading into CL chitosan/hyaluronan (CHI/HA) and poly(L-lysine)/hyaluronan (PLL/HA) films by simple diffusion of the drugs. Sodium diclofenac and paclitaxel were chosen as model drugs and were successfully loaded into the films. The effect of varying the number of layers in the (CHI/HA) films as well as the cross-linker concentration on diclofenac loading were studied. Diclofenac was released from the film in about 10 h. Paclitaxel was also found to diffuse within CL films. Its activity was maintained after loading in the CL films, and cellular viability could be reduced by about 55% over 3 days. Such a simple approach may be applied to other types of cross-linked films and to other drugs. These results prove that it is possible to design multifunctional multilayer films that combine mechanical resistance, biodegradability, and bioactivity properties into a single PEM architecture.     

Use of xylan,an agricultural by-product,in wheat gluten based biodegradable films: mechanical,solubility and water vapor transfer rate properties

The possibility of using xylan, as an agricultural by-product, for production of composite films in combinations with wheat gluten was investigated. Different levels of xylan (0-40% w/w) were incorporated into wheat gluten to form biodegradable composite films. Films were prepared at pH 4 and 11, and dried at either uncontrolled or controlled conditions. The mechanical properties, solubilities and water vapour transfer rate (WVTR) of the composite films were studied. Films were obtained with added xylan without decreasing film-forming quality. Xylan can be used as an additive, as much as 40% (w/w), in wheat gluten films. Changing pH, wheat gluten/xylan ratio, xylan type and drying conditions affected mechanical and solubility properties, however, WVTR was not affected by xylan additions. Wheat gluten/xylan composite films having different characteristics can be produced depending on xylan type, composition and process conditions.     

Tuning the mechanical and physicochemical properties of cross-linked protein films

Films derived from natural sources such as proteins provide an advantage over synthetic films due to their noncytotoxicity, biodegradability, and vast functionality. A new protein source gained from the cataractous eye protein isolate (CEPI) obtained after surgery has been investigated for this purpose. Glycerol has been employed as the plasticizer and glutaraldehyde (GD) as a cross-linker. Fourier transform infrared spectroscopy was employed to characterize the films. Nanoindentation and thermogravimetric analyses reveal improved mechanical and thermal properties of the cross-linked films. The films with 20% (w/w) GD exhibited properties such as the highest modulus and low water solubility. It is possible to tune the properties based on the extent of cross-linking. All the films were completely degraded by the enzyme trypsin. The similarity of these films was checked by using the prepared films as a delivery vehicle for a model compound, ampicillin sodium. The encapsulation efficiency was found to be 74%, and in vitro release studies showed significant amounts of drug release at physiological pH. This study will help us understand how the properties of protein films can be tuned to obtain the desired physicochemical properties. These biodegradable protein films could find use in pharmaceutical industries as delivery carriers.     

Fabrication and Characterization of Native and Oxidized Potato Starch Biodegradable Films

The need to replace conventional polymers due to environmental pollution caused by them has led to increased production of biodegradable polymers such as starch. Thus, the application possibilities of starch have increased. In this study, we produced and characterized biodegradable films derived from native and oxidized potato starch. The film-forming solution was prepared with different concentrations of extracted starch (native or oxidized) and a plasticizer (glycerol or sorbitol). Then, the mechanical, barrier, morphological, and structural properties of the films were characterized. The moisture content of the films varied from 15.35?±?1.31 to 21.78?±?0.49%. The elastic modulus of the films ranged from 219?±?14.97 to 2299?±?62.91 MPa. The film of oxidized starch plasticized with sorbitol in the lowest content was the most resistant and flexible; moreover, this film also presented lower water vapor permeability and low solubility in water. Fourier-transform infrared spectroscopic analysis of the biodegradable films indicated the presence of same functional groups as those of starch with bands in the same regions. The film thickness was lower for the films plasticized with glycerol whereas the color variation (Δ?) was lower for the ones plasticized with sorbitol. In case of both plasticizers, the increase in their content decreased the Δ? value. All the biodegradable films presented stability against water absorption owing to their low solubility in water. Morphological evaluation revealed the presence of partially gelatinized starch granules in the films. The roughness parameter (Rq) of the films varied from 3.39 to 10.9 nm, indicating that their surfaces are smooth. X-ray diffraction studies showed a B-type pattern for the starches, which is representative of tubers. Further, the films present higher relative crystallinity (RC) compared to the starches. The biodegradable starch films are uniform, transparent and with low solubility in water. The oxidation of starch and use of sorbitol as a plasticizer resulted in improved properties of the starch films, which is suitable for application.     

Biodegradable foam plastics based on castor oil

In this work, a simple but effective approach was proposed for preparing biodegradable plastic foams with a high content of castor oil. First of all, castor oil reacted with maleic anhydride to produce maleated castor oil (MACO) without the aid of any catalyst. Then plastic foams were synthesized through free radical initiated copolymerization between MACO and diluent monomer styrene. With changes in MACO/St ratio and species of curing initiator, mechanical properties of MACO foams can be easily adjusted. In this way, biofoams with comparable compressive stress at 25% strain as commercial polyurethane (PU) foams were prepared, while the content of castor oil can be as high as 61 wt %. The soil burial tests further proved that the castor oil based foams kept the biodegradability of renewable resources despite the fact that some petrol-based components were introduced.     

聚乳酸/聚己二酸-对苯二甲酸丁二酯对土壤细菌群落结构的影响及其降解菌的筛选

【背景】近年来,聚乳酸/聚己二酸-对苯二甲酸丁二酯(polylactide/polybutyleneadipateco-terephthalate,PLA/PBAT)可降解地膜得到了广泛的使用,然而材料使用对土壤微生物的影响却鲜有报道。【目的】以新疆土壤为例,研究PLA/PBAT地膜的使用对土壤中微生物群落结构的影响;并从土壤中筛选可降解PLA/PBAT的菌株,为土壤环境的原位修复提供技术支持。【方法】采用高通量测序的方法对比使用PLA/PBAT地膜前后土壤中细菌群落的结构变化;采用筛选培养基从土壤中分离、鉴定PLA/PBAT的降解菌,通过改变不同培养条件研究菌株降解效果。【结果】使用PLA/PBAT地膜后,土壤中酸杆菌门、芽单胞菌门的相对丰度上升,变形菌门、放线菌门的相对丰度下降,这可能是地膜降解过程中其中间产物对土壤pH及微生物的抑制作用所致;并从土壤中分离出一株PLA/PBAT降解菌XJ11,初步鉴定为Delftiatsuruhatensis,在外加1.5%胰蛋白胨的PLA/PBAT (规格1×1×0.05 cm)筛选培养基中,接种菌液1 mL,在pH为7.2、37°C、130 ...     

Biodegradation of polyurethane acrylate with acrylated epoxidized soybean oil blend elastomers by Chaetomium globosum

This paper studies the biodegradation features of a novel blend of polyurethane acrylate-acrylated epoxidized soybean oil-based cross-linked polyurethane elastomers in the presence of the soft-rot fungus Chaetomium globosum. After the specimens were incubated at 28 °C for 90 and 130 days, the degree of fungal damage was measured by analysis of weight loss and mechanical properties. The biodegradation of the films was also evidenced by SEM and FTIR spectroscopic studies. After fungal attack, the FTIR spectra indicate a degradation of urethane and ester groups of the polyurethane and especially of the ester groups from the modified soybean oil part. The polyurethane blend films exposed to fungal attack suffered a loss in strength of up to 55% and a loss in elongation of up to 80%, depending on the content of acrylated epoxidized soybean oil. The biodegradation of the blends was also confirmed by SEM analyses. The biodegradation results show that samples with a high content of acrylated epoxidized soybean oil are more biodegradable than mere polyurethane acrylate. These biodegradable polymer blends present an optimum balance of physical properties and biodegradable properties with the potential for application as eco-friendly biomaterials.     

Electrospun poly (ɛ-caprolactone)/silk fibroin core-sheath nanofibers and their potential applications in tissue engineering and drug release

One of the key tenets of tissue engineering is to develop scaffold materials with favorable biodegradability, surface properties, outstanding mechanical strength and controlled drug release property. In this study, we generated core-sheath nanofibers composed of poly (?-caprolactone) (PCL) and silk fibroin (SF) blends via emulsion electrospinning. Nanofibrous scaffolds were characterized by combined techniques of scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), contact angle and tensile measurements. An in vitro FITC release study was conducted to evaluate sustained release potential of the core-sheath structured nanofibers. We found that the conformation of SF contained in PCL/SF composite nanofibers was transformed from random coil to β-sheet when treated with methanol, leading to improved crystallinity and tensile strength of nanofibrous scaffolds. The hydrophobicity and diameter of nanofibers decreased when we increased the content of SF in PCL/SF composite nanofibers. Furthermore, we evaluated the potential of fabricated PCL/SF composite nanofibers as scaffold in vitro. The results confirmed that fabricated PCL/SF scaffolds improved cell attachment and proliferation. Our results demonstrated the feasibility to generate core-sheath nanofibers composed of PCL and SF using a single-nozzle technique. The produced nanofibrous scaffolds with sustained drug release have potential application in tissue engineering.     

Wood-plastic composites as promising green-composites for automotive industries!

Wood-plastic composite (WPC) is a very promising and sustainable green material to achieve durability without using toxic chemicals. The term WPCs refers to any composites that contain plant fiber and thermosets or thermoplastics. In comparison to other fibrous materials, plant fibers are in general suitable to reinforce plastics due to relative high strength and stiffness, low cost, low density, low CO2 emission, biodegradability and annually renewable. Plant fibers as fillers and reinforcements for polymers are currently the fastest-growing type of polymer additives. Since automakers are aiming to make every part either recyclable or biodegradable, there still seems to be some scope for green-composites based on biodegradable polymers and plant fibers. From a technical point of view, these bio-based composites will enhance mechanical strength and acoustic performance, reduce material weight and fuel consumption, lower production cost, improve passenger safety and shatterproof performance under extreme temperature changes, and improve biodegradability for the auto interior parts.     

Characterization of edible emulsified films with low affinity to water based on kefiran and oleic acid

New edible composite films based on kefiran and oleic acid (OA) at the ratio of 15, 25, and 35% (w/w) were prepared using emulsification with the aim of improving their water vapour barrier and mechanical properties. Film-forming solutions were characterized in terms of rheological properties and particle-size distribution. The impact of the incorporation of OA into the film matrix was studied by investigating the physical, mechanical, and thermal properties of the films. The water vapour permeability (WVP) of the emulsified films was reduced by approximately 33% by adding OA. The mechanical properties of kefiran films were also affected by adding OA: tensile strength was diminished, and elongation increased considerably. Differential scanning calorimetry showed that the glass transition temperature (T_g) of the kefiran film was −16 °C and was not considerably affected by adding OA. Therefore, OA could be incorporated into these films for some food-technology applications that need a low affinity toward water.     

Extrusion of pectin/starch blends plasticized with glycerol

The microstructural and thermal dynamic mechanical properties of extruded pectin/starch/glycerol (PSG) edible and biodegradable films were measured by scanning electron microscopy (SEM) and thermal dynamic mechanical analysis (TDMA). SEM revealed that the temperature profile (TP) in the extruder and the amount of water present during extrusion could be used to control the degree to which the starch was gelatinized. TDMA revealed that moisture and TP during extrusion and by inference the amount of starch gelatinization had little effect on the mechanical properties of PSG films. Furthermore, TDMA revealed that PSG films underwent a glass transition commencing at about −50°C and two other thermal transitions above room temperature. Finally, it was concluded that the properties of extruded PSG films were comparable to those cast from solution.