Copper Uptake by <Emphasis Type="Italic">Pseudomonas aeruginosa</Emphasis> Isolated from Infected Burn Patients

Pseudomonas aeruginosa was isolated from infected burn patients and characterized by standard biochemical tests. The in vitro copper uptake was compared between this isolated pathogenic strain and two non-pathogenic control strains of Gram positive bacteria Bacillus thuringiensis strain Israelis as well as Gram negative bacteria Enterobacter aerogenes. Maximum copper uptake of 470 ppm/g biomass was obtained by P. aeruginosa strain, while the control strains B. thuringiensis and Enterobacter aerogenes had copper uptake of 350 and 383 ppm/g biomass, respectively. However, the lowest copper uptake (60 ppm/g biomass) was observed with another control the saprophytic strain Pseudomonas (Shewanella) putrefaciens. A further investigation regarding the effect of copper toxicity on bacterial growth, gave an MIC score of 600 ppm for P. aeruginosa strain compared to 460 and 300 ppm for the two Gram positive and Gram negative control strains, respectively. In tandem with these in vitro findings, blood analysis on burn patients infected with P. aeruginosa has indicated a selective decrease of copper (hypocupremia) and ceruloplasmin plasma levels. The iron metabolism was also affected by this copper deprivation leading to a similar decrease in plasma levels of PCV, iron, total iron binding capacity, and transferrin. All these hematological changes were significantly different (P < 0.05) from the matched group of non-infected burn patients. The observed hypocupremia in infected burn patients was attributed to demanding scavenger ability by P. aeruginosa strain for the copper of plasma.     

Biosorption of Copper(II) by Live and Dried Biomass of the White Rot Fungi Phanerochaete chrysosporium and Funalia trogii

Biosorption is an innovative and alternative technology to remove heavy metal pollutants from aqueous solution using live, inactive and dead biomasses such as algae, bacteria and fungi. In this study, live and dried biomass of Phanerochaete chrysosporium and Funalia trogii was applied as heavy metal adsorbent material. Biosorption of copper(II) cations in aqueous solution by live and dried biomass of Phanerochaete chrysosporium and Funalia trogii was investigated to study the effects of initial heavy metal concentration, pH, temperature, contact time, agitation rate and amount of fungus. Copper(II) was taken up quickly by fungal biomass (live or dried) during the first 15 min and the most important factor which affected the copper adsorption by live and dried biomass was the pH value. An initial pH of around 5.0 allowed for an optimum adsorption performance. Live biomass of two white rot fungi showed a high copper adsorption capacity compared with dried biomass. Copper(II) uptake was found to be independent of temperature in the range of 20–45 °C. The initial metal ion concentration (10–300 mg/L) significantly influenced the biosorption capacity of these fungi. The results indicate that a biosorption as high as 40–60 % by live and dried biomass can be obtained under optimum conditions.     

Biosorbents for recovery of metals from industrial solutions

Summary Biosorbent materials are a potential alternative to conventional processes of metal recovery from industrial solutions. Algal biomass ofSargassum natans andAscophyllum nodosum outperformed ion exchange resins in sequestering respectively gold and cobalt from solutions. Non-living biomass ofSaccharomyces cerevisiae andRhizopus arrhizus exhibited higher metal-uptake capacity than the living biomass for the uptake of copper, zinc, cadmium, uranium. The solution pH affected the metal-uptake capacity of the biomass whereas the equilibrium biosorption isotherms were independent of the initial concentration of the metal in the solution. Desorption of the metal from the biosorbent and recycle of the biosorbent have also been demonstrated.     

Desorption of Copper from Polyvinyl Alcohol‐Immobilized Seaweed Biomass

The desorption characteristics of copper on biomass of a marine macroalga, Sargassum baccularia, immobilized in polyvinyl alcohol (PVA) gel beads, were investigated using HCl eluting solutions. Both the extent and the rate of desorption were affected by the pH of the eluent. Nearly 91% of the copper initially adsorbed was released back into an HCl solution at pH 1.0 after 40 min of contact time when apparent desorption equilibrium was achieved. When the pH was raised to 2.0, about 81% of the bound copper was desorbed within 120 min of contact time. Apparent desorption rate constants were determined using first‐order desorption models. Very high concentrations of copper in the eluate could be obtained by using small amounts of the HCl eluent. However, this was achieved at the expense of the desorption efficiency. The PVA‐immobilized seaweed biomass beads could be regenerated with HCl solution at pH 1.0 or 2.0 in multiple cycles of copper biosorption‐desorption. Following desorption at pH 1.0 in the first cycle, about 55% of the biosorption capacity of the virgin biomass could be reused in subsequent cycles; in the case of desorption at pH 2.0, about 67% of the original uptake capacity was reusable.     

Considerations on the use of commercially available yeast biomass for the treatment of metal-containing effluents

Summary Three strains ofSaccharomyces cerevisiae and one strain of aCandida sp. obtained from different industrial sources were screened for uptake of silver and copper. Considerable differences in metal uptake capacities were found between the different strains ofS. cerevisiae and betweenS. cerevisiae and theCandida sp. used. Copper uptake capacities ranged from 0.05 mmol g^–1 dry wt to 0.184 mmol g^–1 dry wt while values of 0.034 mmol Ag g^–1 dry wt and 0.193 mmol Ag g^–1 dry wt biomass were observed. Use of ion-selective electrodes (ISEs) enabled the detection of copper complexing agents (possibly proteins and carbohydrates) released by yeasts into the surrounding medium. In contrast, these compounds had no silver complexation abilities. Langmuir and Scatchard transformations of metal adsorption isotherms suggested differences in the mechanisms involved in metal uptake by the various yeasts. The differences between strains ofS. cerevisiae were due possibly to differences in cell wal composition. Different methods of preparation of biomass (fresh, air, oven and freeze-dried) had little effect on metal uptake in comparison with fresh biomass. Storage of fresh waste biomass at 4°C for 20 days had no effect on metal biosorption capacities. It was also observed that individual batches of waste biomass produced from different fermentation runs had consistent metal uptake capacities. The implications of the above results on the use of waste yeast biomass for treatment of metal-containing effluents are discussed.     

Electrooptical Properties of Cells of the Soil Nitrogen-Fixing Bacterium Azospirillum brasilense: Effects of Copper Ions

The effects of copper ions on the uptake of some essential metals in the biomass and the electrooptical properties of cell suspensions of the nitrogen-fixing soil bacterium Azospirillum brasilensesp. 245 were studied. Copper cations were shown to be effectively taken up by the cell biomass from the culture medium. The addition of copper ions increased the rate of uptake of some other metals present in the culture medium. This was accompanied by changes in the electrooptical characteristics of cell suspension as measured within the orienting electric field frequency range of 10 to 10000 kHz. The effects observed during short-term incubation of A. brasilensein the presence of copper cations were less significant than during long-term incubation. These results can be used for the rapid screening of microbial cultures for the enhanced efficiency of sorption and the uptake of metals.     

Assessment of the metal removal capability of two capsulated cyanobacteria, Cyanospira capsulata and Nostoc PCC7936

Two capsulated, exopolysaccharide-producing cyanobacteria, Cyanospira capsulata and Nostoc PCC7936, were tested with regard to their metal removal capability by using copper as model metal. The experiments, carried out with the sole cyanobacterial biomass suspended in distilled water and confined into small dialysis tubings, showed that C. capsulata biomass is characterized by the best efficiency in metal removal, with a q_max (maximum amount of copper removed per biomass unit) of 96 ± 2 mg Cu(II) removed per g of protein in comparison with the value of 79 ± 3 of Nostoc PCC7936 biomass. The experimental data obtained with both cyanobacterial biomass best fit the Langmuir sorption isotherm. The sorption of copper started from the first minutes of contact with the metal and attained the equilibrium state, when no more copper removal was evident, after 5 and 6 hours, for C. capsulata and Nostoc PCC7936, respectively. The best efficiency in Cu(II) removal was obtained at pH 6.1–6.2, while the presence of Mg²⁺ or Ca²⁺ reduced copper removal capability of both species to 60–70% of their q_max. The results showed that the biomass of C. capsulata and Nostoc PCC7936 possesses a high affinity and a high specific uptake for copper, comparable with the best performances shown by other microbial biomass, and suggest the possibility to use the capsulated trichomes of the two cyanobacteria for the bioremoval of heavy metals from polluted water bodies.     

Removal of copper ions by the filamentous fungus, Rhizopus oryzae from aqueous solution

Removal of heavy metals present in wastewaters has been a major concern due to their non-biodegradability and toxicity. Removal of copper ion using NaOH treated Rhizopus oryzae biomass was investigated in a batch reactor. The copper uptake exhibited substantial enhancement both in terms of kinetics of uptake as well as the loading capacity. The copper biosorption by viable and pretreated fungal biomass fit well to a Lagergren's pseudo second order reaction in comparison to pseudo first order kinetics. Investigation on effect of pH indicated improved performance in the range of pH 4-6 in alkali treated biomass. Copper uptake exhibited by viable biomass was highest at 21 degrees C, unlike pretreated biomass that showed maximum uptake across the range of temperature 21-55 degrees C. The maximum copper loading capacity of the viable and pretreated biomass according to Langmuir isotherm was 19.4 and 43.7 mg/g, respectively. Distribution coefficient of pretreated biomass showed improvement at lower residual concentration, indicating a change in the nature of binding by the treated biomass. Copper uptake decreased with an increasing dose of biosorbent, although enhancement in the total metal ion removal was observed at higher dose.     

Absorption of copper and copper–histidine complexes across the apical surface of freshwater rainbow trout intestine

Bioavailability is integral in mediating the delicate balance between nutritive and potentially toxic levels of copper in fish diets. Brush-border membrane vesicles isolated from freshwater rainbow trout intestine were used to characterise apical copper absorption, and to examine the influence of the amino acid histidine on this process. In the absence of histidine, a low affinity, high capacity copper uptake mechanism was described. However, when expressed as a function of ionic copper (Cu²⁺), absorption was linear, rather than saturable, suggesting that the saturable curve was an artifact of copper speciation. Conversely, in the presence of l-histidine (780 μM) saturable uptake was characterised. The uptake capacity discerned (J _max of 354 ± 81 nmol mg protein⁻¹ min⁻¹) in the presence of histidine indicated a significantly reduced capacity for copper transport than that in the absence of histidine. To determine if copper uptake was achievable through putative histidine uptake pathways, copper and histidine were incubated in the presence of tenfold greater concentrations of amino acids proposed to block histidine transporters. Accounting for changes in copper speciation, significant inhibition of uptake by glycine and lysine were noted at copper levels of 699 and 1,028 μM. These results suggest that copper–histidine complexes may be transportable via specific amino acid-transporters in the brush-border membrane.     

Biosorption of copper by fungal melanin

Summary Melanin obtained from Aureobasidium pullulans and Cladosporium resinae was an efficient biosorbent for copper. Copper uptake could be expressed using various adsorption isotherms; melanin from A. pullulans obeyed Freundlich and Langmuir isotherms whereas C. resinae melanin followed the BET isotherm indicating a more complex type of adsorption than in A. pullulans. In general, uptake capacities of melanin were greater than for intact biomass and the higher uptake by pigmented rather than albino biomass could be correlated with the presence of melanin. Cu²⁺ was less readily desorbed from melanin by dilute mineral acids than from intact biomass and again, the relative ease of Cu²⁺ desorption from pre-loaded pigmented or albino biomass was correlated with the presence or absence of melanin. Mg²⁺ and Zn²⁺ appeared to be the most effective cations for desorption with Na⁺ and K⁺ the least effective. The addition of melanin to a coppercontaining culture of the albino strain of A. pullulans resulted in some reduction of toxicity.     

Biosorption of heavy metals by Saccharomyces cerevisiae

Abundant and common yeast biomass has been examined for its capacity to sequester heavy metals from dilute aqueous solutions. Live and non-living biomass of Saccharomyces cerevisiae differs in the uptake of uranium, zinc and copper at the optimum pH 4–5. Culture growth conditions can influence the biosorbent metal uptake capacity which normally was: living and non-living brewer's yeast: U > Zn > Cd > Cu; non-living baker's yeast: Zn > (Cd) > U > Cu; living baker's yeast: Zn > Cu (Cd) > U. Non-living brewer's yeast biomass accumulated 0.58 mmol U/g. The best biosorbent of zinc was non-living baker's yeast ( 0.56 mmol Zn/g). Dead cells of S. cerevisiae removed approximately 40% more uranium or zinc than the corresponding live cultures. Biosorption of uranium by S. cerevisiae was a rapid process reaching 60% of the final uptake value within the first 15 min of contact. Its deposition differing from that of other heavy metals more associated with the cell wall, uranium was deposited as fine-needle-like crystals both on the inside and outside of the S. cerevisiae cells.     

Biosorption of lead and copper from aqueous solutions by pre-treated crab and arca shell biomass

Sorption potential of pretreated crab and arca shell biomass for lead and copper from aqueous media was explored. The effects of pH, initial concentration, biosorbent dosage and contact time were studied in batch experiments. Effects of common ions like sodium, potassium, calcium and magnesium on the sorption capacity of pretreated crab and arca biomasses were also studied. At equilibrium, the maximum uptake by crab shell biomass was 19.83+/-0.29 and 38.62+/-1.27 mg/g for lead and copper, respectively. In case of arca shell biomass the maximum uptake capacity was 18.33+/-0.44 mg/g and 17.64+/-0.31 mg/g for lead and copper, respectively. Combined effect of all the common ions up to 50 microg/ml concentration was negligible for both the metals using both biomasses. Sorption isotherms were studied to explain the removal mechanism of both elements by fitting isotherms data into Lagergren, Freundlich and Langmuir equations.     

Biosorption of uranium and thorium

Selected samples of waste microbial biomass originating from various industrial fermentation processes and biological treatment plants have been screened for biosorbent properties in conjunction with uranium and thorium in aqueous solutions. Biosorption isotherms have been used for the evaluation of biosorptive uptake capacity of the biomass which was also compared to an activated carbon and the ion exchange resin currently used in uranium production processes. Determined uranium and thorium biosorption isotherms were independent of the initial U or Th solution concentration. Solution pH affected the exhibited uptake. In general, lower biosorptive uptake was exhibited at pH 2 than at pH 4. No discernible difference in uptake was observed between pH 4 and pH 5 where the optimum pH for biosorption lies. The biomass of Rhizopus arrhizus at pH 4 exhibited the highest uranium and thorium biosorptive uptake capacity (g) in excess of 180 mg/g. At an equilibrium uranium concentration of 30 mg/liter, R. arrhizus removed approximately 2.5 and 3.3 times more uranium than the ion exchange resin and activated carbon, respectively. Under the same conditions, R. arrhizus removed 20 times more thorium than the ion exchange resin and 2.3 times more than the activated carbon. R. arrhizus also exhibited higher uptake and a generally more favorable isotherm for both uranium and thorium than all other biomass types examined.     

Cadmium biosorption by <Emphasis Type="Italic">Bacillus</Emphasis><Emphasis Type="Italic"> circulans</Emphasis> strain EB1

Summary A heavy metal resistant bacterium, Bacillus circulans strain EB1 showed a high cadmium biosorption capacity coupled with a high tolerance to this metal when grown in its presence. Bacillus circulans EB1 cells grown in the presence of 28.1 mg cadmium/l were capable of removing cadmium with a specific biosorption capacity of 5.8 mg Cd/g dry wt biomass in the first 8 h. When the cells were pre-conditioned with low concentrations of cadmium in pre-grown medium, the uptake was increased to 6.7 mg Cd/g dry wt biomass. The maximum uptake of␣cadmium was during mid-logarithmic phase of growth. The resting cells (both wet and dry) of EB1 were also able to biosorb cadmium. Specific biosorption capacities of wet and dry biomass were 9.8 and 26.5 mg Cd/g dry wt biomass, respectively. Maximum cadmium removals by both wet and dry cells were at pH 7.0. The results showed that the cadmium removal capacity of resting cells was markedly higher than that of growing cells. Since both growing and resting cells had a high biosorption capacity for cadmium, EB1 cells could serve as an excellent biosorbent for removal of cadmium from natural environments.     

Enhancement of Lead(II) Biosorption by Microalgal Biomass Immobilized onto Loofa (Luffa cylindrica) Sponge

A unicellular green microalga, Chlorella sorokiniana, was immobilized on loofa (Luffa cylindrica) sponge and successfully used as a new biosorption system for the removal of lead(II) ions from aqueous solutions. The biosorption of lead(II) ions on both free and immobilized biomass of C. sorokiniana was investigated using aqueous solutions in the concentration range of 10–300 mg/L. The biosorption of lead(II) ions by C. sorokiniana biomass increased as the initial concentration of lead(II) ions increased in the medium. The maximum biosorption capacity for free and immobilized biomass of C. sorokiniana was found to be 108.04 and 123.67 mg lead(II)/g biomass, respectively. The biosorption kinetics were found to be fast, with 96 % of adsorption within the first 5 min and equilibrium reached at 15 min. The adsorption of lead(II) both by free and immobilized C. sorokiniana biomass followed the Langmuir isotherm. The biosorption capacities were detected to be dependent on the pH of the solution; and the maximum adsorption was obtained at a solution pH of about 5. The effect of light metal ions on lead(II) uptake was also studied and it was shown that the presence of light metal ions did not significantly affect lead(II) uptake. The loofa sponge‐immobilized C. sorokiniana biomass could be regenerated using 0.1 M HCl, with up to 99 % recovery. The desorbed biomass was used in five biosorption‐desorption cycles, and no noticeable loss in the biosorption capacity was observed. In addition, fixed bed breakthrough curves for lead(II) removal were presented. These studies demonstrated that loofa sponge‐immobilized biomass of C. sorokiniana could be used as an efficient biosorbent for the treatment of lead(II) containing wastewater.     

Biosorption of Copper by Cyanobacterial Bloom-Derived Biomass Harvested from the Eutrophic Lake Dianchi in China

Biomass of cyanobacterial bloom from Lake Dianchi was used as a biosorbent for copper removal from aqueous solution. The maximum capacity was found at conditions of pH 4, initial concentration of copper was 10 mg/l and initial dose of biomass was 1.0 g/l. HNO₃ demonstrated the highest desorption efficiency compared with HCl, EDTA, and citric acid. Physical adsorption was assumed not to be the dominant mechanism of biosorption as revealed by scanning electron microscopy and surface area measurement of the biomass. Infrared ray spectra analysis of the biomass suggested that ion-exchange is the principal mechanism for biosorption. Considering the advantages—low cost, easy to collect, and huge in quantity—the Microcystis bloom biomass could be used as a sorbent for copper and other heavy metals removal.     

Biosynthesis and Uptake of Copper Nanoparticles by Dead Biomass of Hypocrea lixii Isolated from the Metal Mine in the Brazilian Amazon Region

A biological system for the biosynthesis of nanoparticles (NPs) and uptake of copper from wastewater, using dead biomass of Hypocrea lixii was analyzed and described for the first time. The equilibrium and kinetics investigation of the biosorption of copper onto dead, dried and live biomass of fungus were performed as a function of initial metal concentration, pH, temperature, agitation and inoculum volume. The high biosorption capacity was observed for dead biomass, completed within 60 min of contact, at pH 5.0, temperature of 40°C and agitation speed of 150 rpm with a maximum copper biosorption of 19.0 mg g⁻¹. The equilibrium data were better described using the Langmuir isotherm and kinetic analysis indicated that copper biosorption follows a pseudo-second-order model. The average size, morphology and location of NPs biosynthesized by the fungus were determined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM). NPs were mainly spherical, with an average size of 24.5 nm, and were synthesized extracellularly. The X-ray diffraction (XRD) analysis confirms the presence of metallic copper particles. Infrared spectroscopy (FTIR) study revealed that the amide groups interact with the particles, which was accountable for the stability of NPs. This method further confirmed the presence of proteins as stabilizing and capping agents surrounding the copper NPs. These studies demonstrate that dead biomass of Hypocrea lixii provides an economic and technically feasible option for bioremediation of wastewater and is a potential candidate for industrial-scale production of copper NPs.     

Functional aspects of root architecture and mycorrhizal inoculation with respect to nutrient uptake capacity

The aim of this research was to investigate the effect of arbuscular mycorrhizal (AM) colonisation on root morphology and nitrogen uptake capacity of carob ( Ceratonia siliqua L.) under high and low nutrient conditions. The experimental design was a factorial arrangement of presence/absence of mycorrhizal fungus inoculation ( Glomus intraradices) and high/low nutrient status. Percent AM colonisation, nitrate and ammonium uptake capacity, and nitrogen and phosphorus contents were determined in 3-month-old seedlings. Grayscale and colour images were used to study root morphology and topology, and to assess the relation between root pigmentation and physiological activities. AM colonisation lead to a higher allocation of biomass to white and yellow parts of the root. Inorganic nitrogen uptake capacity per unit root length and nitrogen content were greatest in AM colonised plants grown under low nutrient conditions. A better match was found between plant nitrogen content and biomass accumulation, than between plant phosphorus content and biomass accumulation. It is suggested that the increase in nutrient uptake capacity of AM colonised roots is dependent both on changes in root morphology and physiological uptake potential. This study contributes to an understanding of the role of AM fungi and root morphology in plant nutrient uptake and shows that AM colonisation improves the nitrogen nutrition of plants, mainly when growing at low levels of nutrients.     

Removal of cadmium by Pleurotus sajor-caju basidiomycetes

The bioaccumulation of cadmium by the white rot fungus Pleurotus sajor-caju onto dry biomass was investigated using aqueous media with concentrations in the range of 0.125 mM–1.0 mM The highest cadmium uptake (between 88.9 and 91.8%) was observed with aerobic fungal biomass from the exponential growth phase. Up to 1.0 mM cadmium gradually inhibited mycelium development, but never blocked it completely. Freeze-dried, oven-dried and non-metabolizing live Pleurotus sajor-caju biomass types were tested for their capacity to adsorb the test ion Cd²⁺ within the pH range of 4.5 to 6.0. Freeze–dried biomass proved to be the most efficient biomass type for Cd²⁺ metal adsorption. Therefore, Pleurotus sajor-caju may be used for heavy metal removal and bioremediation.     

Application of adsorption isotherms to chromium adsorption onZ.ramigera

Summary Adsorption isotherms for the adsorption of chromium onZoogloea ramigera are developed. The rates were affected by the pH and temperature of adsorption medium. The biomass ofZ. ramigera at pH 2.0 where the optimum pH for biosorption lies exhibited the highest chromium adsorptive uptake capacity. In general, higher adsorptive uptake was observed at 25°C than 35°C and 45°C.