Development of an acetone/water fractional precipitation process for purification of paclitaxel from plant cell cultures

This study investigated the efficiency of acetone/water fractional precipitation for the purification of paclitaxel from plant cell cultures. Adding distilled water at room temperature into an acetone solution of dissolved crude extract until the acetone/water ratio became 40:60, 30:70, 20:80, and 10:90 (v/v) and stirring the mixture for 10 min at room temperature resulted in paclitaxel yields of 54.3, 89.1, 95.5, and 97.6%, respectively. With an acetone/water ratio of 40:60, v/v, a high yield of paclitaxel (84.8 ~ 86.0%) was produced by an additional 2 h storage at a low temperature (4oC) without additional mixing, or at room temperature with additional mixing. In contrast, preparing the 40:60 (v/v) acetone/water mixture at a low temperature (4oC) and mixing for 10 min at a low temperature, a similar high yield (~ 87.9%) of paclitaxel was obtained immediately. Thus, increasing the proportion of distilled water, or decreasing the temperature of the added water were confirmed as important for obtaining high yields of paclitaxel by acetone/water fractional precipitation.     

Improvement of fractional precipitation process for pre-purification of paclitaxel

Fractional precipitation is a simple, efficient method for pre-purifying paclitaxel extracted from plant cell cultures. However, the fractional precipitation process has been inherently problematic due to the lengthy precipitation time (～3 days) that is required. An improved fractional precipitation process could significantly reduce the precipitation time by increasing the purity of crude extract and the surface area available for precipitation. Glass beads (7 mm) were used to increase the surface area, and the optimal surface area per working volume (i.e. volume of reaction solution) (S/V) for achieving the highest purity and yield of paclitaxel possible was found to be 0.428 mm^?1. The content of paclitaxel dissolved in methanol that can be processed during fractional precipitation was evaluated, and it was established that up to 0.9% (w/v) pure paclitaxel content could be processed. This improved pre-purification process serves to minimize solvent usage and the size and complexity of the high performance liquid chromatography operation required for paclitaxel purification.     

Evaluation of feeding and mixing conditions for fractional precipitation of paclitaxel from plant cell cultures

Fractional precipitation based on the difference in solubility of crude paclitaxel dissolved in methanol, to which distilled water must be added, is the most effective method for the pre-purification of paclitaxel. In this study, the effect of the distilled water feeding and mixing method on the efficiency of fractional precipitation and the formation of paclitaxel precipitate were evaluated. When the distilled water was added all at once, the highest purity (∼57.0%) and yield (∼81.0%) were obtained, and a spherical precipitate was formed by the clustering of crystal branches. On the other hand, when the distilled water was added intermittently in several aliquots, the purity and yield tended to decrease with increasing number of additions, and the precipitate took the form of a cross or pentagon with less clustering of branches. Not mixing after the addition of distilled water resulted in high purity (∼57.0%) and the formation of a spherical precipitate that showed increased branching around the nucleus over time. In contrast, when the sample was mixed intermittently after adding distilled water, paclitaxel was obtained in high yield (∼99.7%). Continuously mixing the sample after adding distilled water, however, caused the precipitate crystals to be broken into smaller pieces.     

Development of a micelle-fractional precipitation hybrid process for the pre-purification of paclitaxel from plant cell cultures

A micelle-fractional precipitation hybrid process was developed for the effective pre-purification of the anticancer agent paclitaxel extracted from plant cell cultures. First, it was found that the efficiency of such a developed process could be remarkably enhanced by removing waxy substances originating from plant cells using the adsorbent sylopute. Paclitaxel yield was improved and the fractional precipitation time was shortened by increasing the surface area per working volume (S/V) of the reacting solution through the addition of a cation exchange resin (Amberlite IR120 or Amberlite 200), an anion exchange resin (Amberlite IRA400 or Amberlite IRA96), or glass beads. Most of the paclitaxel (>98%) could be obtained after about 12 h of fractional precipitation using Amberlite 200. Purity increased with increasing fractional precipitation time up to 9 h to about 85%, after which it showed little change. On the other hand, no paclitaxel precipitate was formed using either of the nonionic exchange resins because paclitaxel, which is hydrophobic, was strongly adsorbed on the hydrophobic resin surface. Since high-purity paclitaxel can be obtained in high yield and the precipitation time can be reduced by combining micelle formation with fractional precipitation, this hybrid method is expected to significantly enhance the final purification process.     

Fractional precipitation for paclitaxel pre-purification from plant cell cultures of Taxus chinensis

Fractional precipitation is a simple and efficient procedure for pre-purification of paclitaxel. The optimal methanol composition in water, paclitaxel content in crude extract, storage temperature, and time were 61.5% (v/v), 0.5% (w/v), 0°C, and 3 days, respectively. As purity of the paclitaxel in the crude extract increases, the purity and yield of paclitaxel from fractional precipitation increases. This pre-purification process serves to minimize the solvent usage, size and complexity of the HPLC operations for paclitaxel purification. This process is readily scalable to a pilot plant and eventually to a production environment where multikilogram quantities of material are expected to be produced.     

A robust whole-cell biocatalyst that introduces a thermo- and solvent-tolerant lipase into Aspergillus oryzae cells: Characterization and application to enzymatic biodiesel production

To develop a robust whole-cell biocatalyst that works well at moderately high temperature (40–50 °C) with organic solvents, a thermostable lipase from Geobacillus thermocatenulatus (BTL2) was introduced into an Aspergillus oryzae whole-cell biocatalyst. The lipase-hydrolytic activity of the immobilized A. oryzae (r-BTL) was highest at 50 °C and was maintained even after an incubation of 24-h at 60 °C. In addition, r-BTL was highly tolerant to 30% (v/v) organic solvents (dimethyl carbonate, ethanol, methanol, 2-propanol or acetone). The attractive characteristics of r-BTL also worked efficiently on palm oil methanolysis, resulting in a nearly 100% conversion at elevated temperature from 40 to 50 °C. Moreover, r-BTL catalyzed methanolysis at a high methanol concentration without a significant loss of lipase activity. In particular, when 2 molar equivalents of methanol were added 2 times, a methyl ester content of more than 90% was achieved; the yield was higher than those of conventional whole-cell biocatalyst and commercial Candida antarctica lipase (Novozym 435). On the basis of the results regarding the excellent lipase characteristics and efficient biodiesel production, the developed whole-cell biocatalyst would be a promising biocatalyst in a broad range of applications including biodiesel production.     

Determination of pyrrole–imidazole polyamide in rat plasma by liquid chromatography–tandem mass spectrometry

Pyrrole (Py)–imidazole (Im) polyamides synthesized by combining N-methylpyrrole and N-methylimidazole amino acids have been identified as novel candidates for gene therapy. In this study, a sensitive method using liquid chromatography–tandem mass spectrometry (LC–MS/MS) with an electrospray ionization (ESI) source was developed and validated for the determination and quantification of Py–Im polyamide in rat plasma. Py–Im polyamide was extracted from rat plasma by solid-phase extraction (SPE) using a Waters Oasis^® HLB cartridge. Separation was achieved on an ACQUITY UPLC HSS T3 (1.8 μm, 2.1 × 50 mm) column by gradient elution using acetonitrile:distilled water:acetic acid (5:95:0.1, v/v/v) and acetonitrile:distilled water:acetic acid (95:5:0.1, v/v/v). The method was validated over the range of 10–1000 ng/mL and the lower limit of quantification (LLOQ) was 10 ng/mL. This method was successfully applied to the investigation of the pharmacokinetics of Py–Im polyamide after intravenous administration.     

Organic solvent extraction and metabonomic profiling of the metabolites in erythrocytes

We used erythrocytes as the model tissue to evaluate an optimal solution for the extraction of intracellular metabolites and time-dependent variation of the metabolome in living cells. Projection to latent structure (PLS) of the GC/MS and LC/MS data suggested that the most efficient solution for the extraction of metabolites from wet erythrocytes (50 mg) could be a methanol–chloroform–water mixture (950 μL, 700:200:50, v/v/v). PLS-discriminant analysis (DA) clearly profiled a time-dependent alternation of metabolic phenotype of erythrocytes. Identification of the metabolites showed that the process was characterized by accumulating of metabolic products and depleting of nutritious substances in erythrocytes during incubation.     

Simultaneous determination of citalopram and its metabolite in human plasma by LC–MS/MS applied to pharmacokinetic study

A simple sensitive and robust method for simultaneous determination of citalopram and desmethylcitalopram was developed using liquid chromatography tandem mass spectrometry (LC–MS/MS). A 200 μL aliquot of plasma sample was employed and deproteinized with methanol and desipramine was used as the internal standard. After vortex mixing and centrifugation, the supernatant was diluted with water (1:1, v/v) and then directly injected to analysis. Analytes were separated by a Zorbax XDB C₁₈ column with the mobile phase composed of acetonitrile and water (30:70, v/v) with 0.25% formic acid and monitored in MRM mode using a positive electrospray source with tandem mass spectrometry detection. The total run time was 3.5 min. The dynamic range was 0.2–100 ng/mL for citalopram and 0.25–50 ng/mL for desmethylcitalopram, respectively. Compared to the best existing literatures for plasma samples, the same LOQ for CIT (0.5 ng/mL) and lower LOQ for DCIT (0.25 vs 5 ng/mL) were reached, and less sample preparation steps and runtime (3.5 vs 10 min) were taken for our method. Accuracy and precision was lower than 8% and lower than 11.5% for either target. Validation results and its application to the analysis of plasma samples after oral administration of citalopram in healthy Chinese volunteers demonstrated the method was applicable to pharmacokinetic studies.     

Evaluation of adsorbents for separation and purification of paclitaxel from plant cell cultures

In this study, we evaluated the efficiency of different adsorbents for the removal of plant-derived impurities during the pre-purification of paclitaxel from plant cell cultures. Using the synthetic adsorbents sylopute and active clay and their major components SiO₂ and MgO, we performed adsorbent treatment and analyzed the paclitaxel precipitates recovered from hexane precipitation. When SiO₂ was used, the highest purity (～58.1%) and yield (～91.5%) of paclitaxel were obtained. We also determined differences in the effectiveness of the adsorbent treatment according to changes in the surface area, pore volume and pore diameter of SiO₂. Adsorbent treatment was more effective when pore diameter was larger (silica I [2.19 nm] < silica II [4.92 nm] < silica III [9.07 nm]). The highest purity (～74.3%) and yield (～92.9%) of paclitaxel were obtained when silica III was used in the adsorbent treatment. Pore diameter had a greater effect on the removal of plant-derived impurities during the pre-purification of paclitaxel compared with surface area and pore volume. This result could be confirmed by HPLC analysis of the absorbent after treatment and TGA of the organic substances that were bonded to the adsorbent.     

A straightforward procedure to biosynthesise melatonin using freshly chopped Achillea millefolium L. as reagent

d, l-Tryptophan as the precursor of melatonin and Achillea millefolium L. as the plant cell tissue were used in order to force the plant enzymatic system to enhance the production of melatonin.The biotransformation protocol was performed by adding the precursor to the freshly chopped plant material suspended in water and stirred at room temperature in total darkness. The melatonin content was evaluated by LC-DAD-ESI-MS. The precursor-treated sample gave at least six times (345 ng/g_{fresh plant}) the melatonin amount usually produced in young plants of A. millefolium L. (50 ng/g_fresh plant).The present study shows that, in principle, adding a specific precursor to a suitable freshly chopped plant material can significantly enhance a secondary metabolite production.     

Downstream processing and characterization of pullulan from a novel colour variant strain of Aureobasidium pullulans FB-1

Exopolysaccharide produced by a new novel colour variant strain of Aureobasidium pullulans FB-1 was purified by cell harvesting and precipitation of the polymer. Various organic solvents were screened for pullulan precipitation. Isolation and purification of pullulan from fermentation broth was carried out using single-step purification strategy by isopropyl alcohol precipitation. Ratio of culture supernatant to isopropyl alcohol and time of precipitation were optimized for pullulan precipitation. Maximum yield (4.47%, w/v) of polysaccharide was obtained when two volumes of ice-cold isopropyl alcohol were added to one volume of supernatant with precipitation time of 12 h. IR spectra as well as carbon-13 and proton NMR spectra in aqueous solution of intact polysaccharide obtained from A. pullulans FB-1 and commercially available pullulan (Sigma, USA) revealed solely α-(1 → 6) linked maltosyl units, in accord with the generally accepted structure of pullulan. Maximum hydrolysis (94.25%) of purified pullulan at 50 °C by pullulanase was achieved under agitation (150 rpm) after 360 min.     

Solid-phase extraction of tanshinones from Salvia Miltiorrhiza Bunge using ionic liquid-modified silica sorbents

New ionic liquid-modified silica sorbents were developed by the surface chemical modification of the commercial silica using synthesized ionic liquids. The obtained ionic liquid-modified particles were successfully used as a special sorbent in solid-phase extraction process to isolation of cryptotanshinone, tanshinone I and tanshinone IIA from Salvia Miltiorrhiza Bunge. Different washing and elution solvents such as water, methanol and methanol–acetic acid (90/10, v/v) were evaluated. A comparison of ionic liquid-modified silica cartridges and traditional silica cartridge show that higher recovery was observed using ionic liquid-modified silica sorbents. A quantitative analysis was conducted by high-performance liquid chromatography using a C₁₈ column (5 μm, 150 mm × 4.6 mm) with methanol–water (78:22, v/v, and containing 0.5% acetic acid) as a mobile phase. Good linearity was obtained from 0.5 × 10^?4 to 0.5 mg/mL (r² > 0.999) with the relative standard deviations less than 4.8%.     

Validation of a quantitative assay for human neutrophil peptide-1, -2, and -3 in human plasma and serum by liquid chromatography coupled to tandem mass spectrometry

A quantitative assay for simultaneous measurement of individual human neutrophil peptide-1, -2 and -3 concentrations will aid in exploring the potential of these antimicrobial peptides as biomarkers for various diseases. Therefore, a liquid chromatography–tandem mass spectrometry method has been developed and validated to allow separate quantification of the three human neutrophil peptides in human plasma and serum. Plasma and serum samples (100 μl) were deproteinized by precipitation, followed by chromatographic separation on a Symmetry 300 C₁₈ column (50 mm × 2.1 mm I.D., particle size 3.5 μm), using a water–methanol gradient containing 0.25% (v/v) formic acid and human alpha-defensin 5 as internal standard. Tandem mass spectrometric detection was performed on a triple quadrupole mass spectrometer equipped with electrospray ionization. Despite low fragmentation efficiency of the antimicrobial peptides, multiple reaction monitoring was used for detection, though selecting the quaternary charged ions as both precursor and product. The method was linear for concentrations between 5 and 1000 ng/ml with a limit of detection around 3 ng/ml for all peptides. Intra- and inter-assay precisions were 14.8 and 19.1%, respectively, at the lowest measured endogenous concentration (6.4 ng/ml of HNP-1 in plasma), representing the lower limit of quantification of the assay. Recoveries of HNP-1, -2 and -3 from plasma and serum ranged between 85 and 128%. Analysis of serum samples from intensive care patients showed average concentrations of 362, 570 and 143 ng/ml for HNP-1, -2 and -3, respectively.     

Validation and application of a liquid chromatography–tandem mass spectrometric method for quantification of the drug transport probe fexofenadine in human plasma using 96-well filter plates

A rapid method to determine fexofenadine concentrations in human plasma using protein precipitation in 96-well plates and liquid chromatography–tandem mass spectrometry was validated. Plasma proteins were precipitated with acetonitrile containing the internal standard fexofenadine-d6, mixed briefly, and then filtered into a collection plate. The resulting filtrate was diluted and injected onto a Phenomenex Gemini C18 (50 mm × 2.0 mm, 5 μm) analytical column. The mobile phase consisted of 0.1% formic acid, 5 mM ammonium acetate in deionized water and methanol (35:65, v/v). The flow rate was 0.2 ml/min and the total run time was 2 min. Detection of the analytes was achieved using positive ion electrospray ionization and high resolution multiple reaction monitoring mode (H-SRM). The linear standard curve ranged from 1 to 500 ng/ml and the precision and accuracy (intra- and inter-run) were within 4.3% and 8.0%, respectively. The method has been applied successfully to determine fexofenadine concentrations in human plasma samples obtained from subjects administered a single oral dose of fexofenadine. The method is rapid, sensitive, selective and directly applicable to human pharmacokinetic studies involving fexofenadine.     

Simultaneous determination of paracetamol,pseudoephedrine, dextrophan and chlorpheniramine in human plasma by liquid chromatography–tandem mass spectrometry

For the first time, a highly sensitive and simple LC–MS/MS method after one-step precipitation was developed and validated for the simultaneous determination of paracetamol (PA), pseudoephedrine (PE), dextrophan (DT) and chlorpheniramine (CP) in human plasma using diphenhydramine as internal standard (IS). The analytes and IS were separated on a YMC-ODS-AQ C₁₈ Column (100 mm × 2.0 mm, 3 μm) by a gradient program with mobile phase consisting of 0.3% (v/v) acetic acid and methanol at a flow rate of 0.30 mL/min. Detection was performed on a triple quadrupole tandem mass spectrometer via electrospray ionization in the positive ion mode. The method was validated and linear over the concentration range of 10–5000 ng/mL for PA, 2–1000 ng/mL for PE, 0.05–25 ng/mL for DT and 0.1–50 ng/mL for CP. The accuracies as determined from quality control samples were in range of ?8.37% to 3.13% for all analytes. Intra-day and inter-day precision for all analytes were less than 11.54% and 14.35%, respectively. This validated method was successfully applied to a randomized, two-period cross-over bioequivalence study in 20 healthy Chinese volunteers receiving multicomponent formulations containing 325 mg of paracetamol, 30 mg of pseudoephedrine hydrochloride, 15 mg of dextromethorphan hydrobromide and 2 mg of chlorphenamine maleate.     

Simultaneous analysis of isomers of escin saponins in human plasma by liquid chromatography–tandem mass spectrometry: Application to a pharmacokinetic study after oral administration

A rapid and sensitive bioassay based on liquid chromatography–tandem mass spectrometry (LC–MS/MS) for the simultaneous determination of four isomeric escin saponins (escin Ia, escin Ib, isoescin Ia and isoescin Ib) in human plasma has been developed and validated. Sample preparation of plasma after addition of telmisartan as internal standard (I.S.) involved solid-phase extraction (SPE) on C18 cartridges. Separation was based on reversed phase chromatography using gradient elution with methanol–acetonitrile (50:50, v/v) and 10 mM ammonium acetate solution (pH 6.8). MS/MS detection in the positive ion mode used multiple reaction monitoring of the transition at m/z 1113.8 → 807.6. Stability issues with the four saponins required the addition of formic acid to plasma samples prior to storage at ?80 °C and analysis within 30 days. The method was linear at concentrations up to 10 ng/mL with correlation coefficients > 0.996 for all analytes. The lower limit of quantitation (LLOQ) for all four saponins was 33 pg/mL. Intra- and inter-day precisions (as relative standard deviation) were all <15% and accuracies (as relative error) in the range ?5.3% to 6.1%. The method was successfully applied to a pharmacokinetic study of escins in healthy volunteers after oral administration of sodium aescinate tablets containing 60 mg escin saponins.     

Optimized synthesis of (Z)-3-hexen-1-yl caproate using germinated rapeseed lipase in organic solvent

(Z)-3-hexen-1-yl esters are important green top-note components of food flavors and fragrances. Effects of various process conditions on (Z)-3-hexen-1-yl caproate synthesis employing germinated rapeseed lipase acetone powder in organic solvent were investigated. Rapeseed lipase catalyzed ester formation more efficiently with non-polar compared to polar solvents despite high enzyme stability in both types of solvents. Maximum ester yield (90%) was obtained when 0.125 M (Z)-3-hexen-1-ol and caproic acid were reacted at 25 °C for 48 h in the presence of 50 g/L enzyme in heptane. Enzyme showed little sensitivity towards a_w with optimum yield at 0.45, while added water did not affect ester yield. Esterification reduced by increasing molecular sieves (>0.0125%, w/v). The highest yields of caproic acid were obtained with isoamyl alcohol (93%) followed by butanol and (Z)-3-hexen-1-o1 (88%) respectively reflecting the enzyme specificity for straight and branched chain alcohols. Secondary alcohols showed low reactivity, while tertiary alcohol had either very low reactivity or not esterified at all. A good relationship has been found between ester synthesis and the solvent polarity (log P value); while no correlation for the effect of solvents on residual enzyme activity was observed. It may be concluded that germinated rapeseed lipase is a promising biocatalyst for the synthesis of valuable green flavor note compound. The enzyme also showed a wide range of temperature stability (5–50 °C).     

Response in root morphology and nutrient contents of Myriophyllum spicatum to sediment type

Sediment may play an important role during the submerged macrophyte decline in the eutrophication progress. In order to investigate the response in root morphology and nutrient contents of submerged macrophytes Myriophyllum spicatum to sediment, five sediment types were treated and used (five types of sediment were used in the experiment: treatment 1 was nature sediment + sand, a 50:50 (v/v) mixture, treatment 2 was the studied sediment only, treatment 3 was sediment + nitrogen (N, NH₄Cl 400 mg kg^?1), treatment 4 was sediment + phosphorus (P, NaH₂PO₄ 300 mg kg^?1); treatment 5 was sediment + phosphorus (P, NaH₂PO₄ 600 mg kg^?1)). The results show that the root N content was only significantly affected by adding N in sediments and P was elevated by adding N and P. The root mass and its percentage increased at first, the peak values were reached at 35 d, and then decreased. The root growth was restrained by adding sand and N in sediments, root senescence process was delayed at the later experimental time by adding P in sediments. The increase of root volume showed a similar trend to that of root growth, except for plant with P addition where root volume remained high after 35 d. The root volume decreased while the main root number increased significantly by adding sand in sediments. The mean root length and main root diameter were reduced by adding P in sediments. The compatible sediment nutrient condition is necessary to restore submerged macrophytes in a degraded shallow lake ecosystem, and the effect of sediment on the root morphology and nutrient content is one of the important aspects restricting the restoration of submerged macrophytes.     

Simultaneous determination of etoposide and a piperine analogue (PA-1) by UPLC–qTOF-MS: Evidence that PA-1 enhances the oral bioavailability of etoposide in mice

In the present investigation, a UPLC–qTOF-MS/MS method has been developed for the simultaneous determination of etoposide and a piperine analogue, namely, 4-ethyl 5-(3,4-methylenedioxyphenyl)-2E,4E-pentadienoic acid piperidide (PA-1). The analytes were separated on a reverse phase C18 column using methanol–water (72:28, v/v) mobile phase with a flow rate of 250 μL/min. The qTOF-MS was operated under multiple reaction monitoring mode using electro-spray ionization (ESI) technique with positive ion polarity. The major product ions for etoposide and PA-1 were at m/z 185.1350 and 164.1581, respectively. The recovery of the analytes from mouse plasma was optimized using solid phase extraction technique. The total run time was 6 min and the elution of etoposide and PA-1 occurred at 1.24 and 2.84 min, respectively. The calibration curves of etoposide as well as PA-1 were linear over the concentration range of 2–1000 ng/mL (r², 0.9829), and 1–1000 ng/mL (r², 0.9989), respectively. For etoposide intra-assay and inter-assay accuracy in terms of % bias was in between ?7.65 to +6.26, and ?7.83 to +5.99, respectively. For PA-1 intra-assay and inter-assay accuracy in terms of % bias was in between ?7.01 to +9.10, and ?7.36 to +6.71, respectively. The lower limit of quantitation for etoposide and PA-1 were 2.0 and 1.0 ng/mL, respectively. Analytes were stable under various conditions (in autosampler, during freeze–thaw, at room temperature, and under deep-freeze conditions). The method was used for a pharmacokinetic study which showed that PA-1 enhanced the oral bioavailability of etoposide in mice by 2.32-fold.