Recovery of Clostridium thermosulfurogenes produced beta-amylase by (hydroxypropyl)methylcellulose partition.

A procedure for recovering Clostridium thermosulfurogenes produced beta-amylase from fermentation broth by partition was developed. The partition was achieved by addition of ammonium sulfate to an aqueous solution of the enzyme with (hydroxypropyl)methylcellulose. The beta-amylase-containing pellet formed upon centrifugation could be redissolved and the polymer recovered by a second salt addition. The process was not dependent on polymer/enzyme solution pH, but it was affected by temperature, polymer nominal molecular weight and loading, and fermentation carbon source. Unlike more traditional aqueous-phase partitions, such as poly(ethylene glycol)/dextran, the current approach appeared to be biospecific.     

Design of mucoadhesive polymeric films based on blends of poly(acrylic acid) and (hydroxypropyl)cellulose

Mixing of aqueous solutions of poly(acrylic acid) and (hydroxypropyl)cellulose results in formation of hydrogen-bonded interpolymer complexes, which precipitate and do not allow preparation of homogeneous polymeric films by casting. In the present work the effect of pH on the complexation between poly(acrylic acid) and (hydroxypropyl)cellulose in solutions and miscibility of these polymers in solid state has been studied. The pH-induced complexation-miscibility-immiscibility transitions in the polymer mixtures have been observed. The optimal conditions for preparation of homogeneous polymeric films based on blends of these polymers have been found, and the possibility of radiation cross-linking of these materials has been demonstrated. Although the gamma-radiation treatment of solid polymeric blends was found to be inefficient, successful cross-linking was achieved by addition of N,N'-methylenebis(acrylamide). The mucoadhesive potential of both soluble and cross-linked films toward porcine buccal mucosa is evaluated. Soluble films adhered to mucosal tissues undergo dissolution within 30-110 min depending on the polymer ratio in the blend. Cross-linked films are retained on the mucosal surface for 10-40 min and then detach.     

Affinity separation of immunoglobulin G subclasses on dye attached poly(hydroxypropyl methacrylate) beads

Poly(hydroxypropyl methacrylate) [poly(HPMA)] gel beads with an average size of 150–200 μm were prepared by suspension polymerization of hydroxypropyl methacrylate (HPMA). The poly(HPMA) gel beads were characterized by swelling studies, surface area measurements, scanning electron microscopy (SEM) and elemental analysis. Poly(HPMA) gel beads had a specific surface area of 88.6 m²/g. The dye Reactive Green HE 4BD was chemically attached to yield dye-poly(HPMA) gel beads at an average concentration of 44.3 μmol dye/g bead with a swelling ratio of 75%. These dye attached gel beads were used in the separation of immunoglobulin-G (IgG) through adsorption–elution studies. The non-specific adsorption of IgG on the poly(HPMA) gel beads was 0.5 mg/g. The attachment of Reactive Green HE 4BD significantly increased the adsorption of IgG up to 71 mg/g. The Langmuir adsorption model was found to be applicable in interpretation of data pertaining to the adsorption studies of IgG with Reactive Green HE 4BD attached to the poly(HPMA) gel beads. The adsorption of IgG was found to be optimal at pH 7.0. The adsorption of IgG was observed to decrease by about 76% as the NaCl concentration was increased from 0.001 to 0.1 M. The IgG adsorption capacity of the dye attached poly(HPMA) gel beads was determined for a commercially available IgG solution to be 4.2 mg/g for IgG₁, 64.5 mg/g for IgG₂, 7.1 mg/g for IgG₃ and 10.8 mg/g for IgG₄. The Reactive Green HE 4BD attached poly(HPMA) gel beads have a significant adsorption capacity for IgG₂. The quantity of adsorbed IgG₂ is three times higher than the quantity of the other subclasses, IgG₁, IgG₃ and IgG₄. A similar adsorption behaviour was observed when the albumin free human plasma was used. The quantity of adsorbed IgG₂ is higher than the quantity of the other subclasses, IgG₁, IgG₃ and IgG₄. Adsorption capacities for albumin free human plasma were obtained as 6.4 mg/g for IgG₁, 67.8 mg/g for IgG₂, 5.2 mg/g for IgG₃ and 8.6 mg/g for IgG₄. Significant amount of the adsorbed IgG (up to 95%) was eluted in 1 h in the elution medium containing 2.0 M NaCl. Repeated adsorption/elution processes showed that these dye attached gel beads are suitable for IgG adsorption.     

Preparation of cholesteric (hydroxypropyl)cellulose/polymer networks and ion-mediated control of their optical properties

(Hydroxypropyl)cellulose (HPC)/vinyl polymer networks were synthesized in film form from liquid-crystalline solutions of HPC in a mixed solvent of methacrylate monomer/methanol/water (2:1:2 in weight) containing cross-linking agents, via photopolymerization of the methacrylate monomer. Di(ethylene glycol) monomethyl ether methacrylate (DEGMEM) or 2-hydroxypropyl methacrylate (HPMA) was used as the polymerizing monomer, and tetra(ethylene glycol) diacrylate and glutaraldehyde were the cross-linkers for the monomers and HPC, respectively. The polymer composite films, HPC/PDEGMEM and HPC/PHPMA, prepared at ca. 60-70 wt % concentrations of HPC in the starting solutions, were iridescently colored due to the selective light reflection, originating from the cholesteric helical arrangement carried over successively into the network system. When the cholesteric films were immersed and swollen in water containing an inorganic neutral salt, their coloration and optical turbidity varied according to a strength of 'chaotropicity' of the impregnant ions. This ionic effect may be interpreted as essentially identical with that found formerly in the coexistent salt-sort dependence of the cholesteric pitch and lower critical solution temperature for HPC aqueous solutions. It is also demonstrated that visual appearance of the swollen networks can be changed by application of an electric potential of practical magnitude between both edges of the samples of rectangular shape.     

Developing hydroxypropyl methylcellulose/hydroxypropyl starch blends for use as capsule materials

Blends of hydroxypropyl methylcellulose (HPMC) with up to 70% hydroxypropyl starch (HPS) were developed for use as hard capsule materials. Polyethylene glycol (PEG) was used as both a plasticizer and a compatibilizer in the blends. In order to prepare hard capsules for pharmaceutical application using the well-established method of dipping stainless steel mold pins into solution then drying at certain temperature, equilibrated solutions with higher solids concentration (20%) were investigated and developed. The solutions, films and capsules of the different HPMC/HPS blends were characterized by viscosity, transparency, tensile testing, water contact angle, SEM, as well as FTIR. The results showed that the blend system is immiscible but compatible in certain degree, especially after adding PEG. The hydroxypropylene groups grafted onto both cellulose and starch improved the compatibility between the HPMC and the modified starch. The higher viscosity of starch at lower temperature improved the viscosity balance of the system, which enlarged the operation window for the dipping–drying technique. The PEG increased the transparency and toughness of the various blends. By optimizing temperature and incubation time to control viscosity, capsules of various blends were successfully developed.     

Preparation and characterization of water soluble poly(acrylic acid)–hydroxypropyl cellulose composite

Purified flax waste was obtained from flax processing wastes via subjecting the latter to alkali treatment followed by peracetic acid bleaching. The so obtained purified flax wastes were chemically modified via reacting with propylene oxide in alkaline medium. The resultant hydroxypropyl cellulose (HPC) was incorporated in a polymerization medium containing acrylic acid and potassium bromate/thiourea mixture as initiation system. The polymerization reaction was monitored by determining the total conversion percent and the rheological properties of the resultant polyacrylic acid–hydroxypropyl cellulose composite [poly(AA)–HPC]. Results obtained indicate that the optimum conditions of polymerization process were: 12 mmole KBrO₃, 4 mmole thiourea and 100 g acrylic acid/100 g HPC at 50 °C for 2 h using a material to liquor ratio of 1:5.     

Cutinase purification on poly(ethylene glycol)–hydroxypropyl starch aqueous two-phase systems

The partition behaviour of cutinase on poly(ethylene glycol) (PEG)–hydroxypropyl starch aqueous two-phase systems was characterized. The effect of molecular mass of PEG, the pH of the system and tie-line length on cutinase partition coefficient and cutinase yield to the top phase was investigated for systems prepared with a purified hydroxypropyl starch (Reppal PES 100) and a crude one (HPS). The effect of the presence of different salts, such as sodium chloride, sodium sulphate and ammonium sulphate, on cutinase partition was also studied. The results lead to the conclusion that aqueous two-phase systems composed of PEG and hydroxypropyl starch are not efficient in the purification of cutinase. In the majority of cases, the partition coefficients were very close to 1, with pH being the factor which affects most cutinase partition. Partition coefficients were significantly improved when salts were added to the systems. For PEG 4000–Reppal PES 100 [at pH 4.0; 0.5 M (NH₄)₂SO₄], the partition coefficient for cutinase was 3.7, while a value of 12 was obtained for PEG 4000–HPS (at pH 4.0; 1 M NaCl). An isoelectric point (pI) of 7.8 was confirmed for cutinase by constructing a cross partition graphic from the results obtained in the experiments with different salts.     

Utilization of hydroxypropyl cellulose and poly(acrylic acid)-hydroxypropyl cellulose composite as thickeners for textile printing

Trials were carried out to partially replace kerosene oil with hydroxypropyl cellulose (HPC), poly(acrylic acid)-hydroxypropyl cellulose composite (poly (AA)-HPC) and their mixture in pigment printing paste. Partial replacement was carried out under a variety of conditions. Variables studied include type and concentration of the aqueous thickening agent and type of pigment dyes. In addition to that, poly (AA)-HPC composite was tried to replace sodium alginate in reactive printing. The fastness properties, color strength and stiffness were measured for the reactive and pigment printed samples.     

Method to recover a lipophilic drug from hydroxypropyl methylcellulose matrix tablets

A reverse-phase high-performance liquid chromatographic (HPLC) method for recovery of the lipophilic drug, alprazolam, from matrix tablets containing the hydrophilic polymer hydroxypropyl methylcellulose (HPMC) was developed. Lipophilic drugs, such as alprazolam, are difficult to completely extract and quantitate from tablets containing HPMC polymer. The percentage of recoveries of alprazolam from placebo powder spiked with alprazolam stock solution and from placebo powder mixed with alprazolam powder were about 100% and 85% to 95%, respectively. The validated method using water to completely dissolve HPMC before the addition of a strong solvent to dissolve and extract the drug from the HPMC solution was shown to be the most reproducible method. Different molecular weight distributions of the HPMC polymer, such as HPMC-K4M and HPMC-K100LV, did not influence the dissolution results of alprazolam using this validated method. Similarly, the excipients composing the matrix tablet formulations, such as dicalcium phosphate dihydrate, dicalcium phosphate anhydrous, calcium sulfate dihydrate, sucrose, dextrose, and lactose monohydrate, did not influence the percent recovery of alprazolam. The recovery method reported herein was shown to be the most efficient to achieve complete recovery of alprazolam from powder blends and tablets containing a variety of excipients and different grades of HPMC.     

Preparation and antimicrobial activity of hydroxypropyl chitosan

Water-soluble hydroxypropyl chitosan (HPCS) derivatives with different degrees of substitution (DS) and weight-average molecular weight (Mw) were synthesized from chitosan and propylene epoxide under basic conditions. Their structure was characterized by IR spectroscopy, NMR spectroscopy, and elemental analysis, which showed that both the OH groups at C-6 and C-3 and the NH2 group of chitosan were alkylated. The DS value of HPCS ranged from 1.5 to 3.1 and the Mw was between 2.1x10(4) and 9.2x10(4). In vitro antimicrobial activities of the HPCS derivatives were evaluated by the Kirby-Bauer disc diffusion method and the macrotube dilution broth method. The HPCS derivatives exhibited no inhibitory effect on two bacterial strains (Escherichia coli and Staphylococcus aureus); however, some inhibitory effect was found against four of the six pathogenic fruit fungi investigated. Some derivatives (HPCS1, HPCS2, HPCS3, HPCS3-1, and HPCS4) were effective against C. diplodiella and F. oxysporum. HPCS3-1 is the most effective one with MIC values of 5.0, 0.31, 0.31, and 0.16mg/mL against A. mali, C. diplodiella, F. oxysporum, and P. piricola, respectively. Antifungal effects were also observed for HPCS2 and HPCS3-1 against A. mali, as well as HPCS3 and HPCS3-1 against P. piricola. The results suggest that relatively lower DS and higher Mw value enhances the antifungal activity of HPCS derivatives.     

Modification of hydroxypropyl guar gum with ethanolamine

A new guar gum derivative containing amino group was synthesized through nucleophilic substitution of p-toluenesulfonate activated hydroxypropyl guar gum with ethanolamine. For the preparation of p-toluenesulfonate esters hydroxypropyl guar gum, the results showed that the reaction rate was optimal at 25°C and the reaction could reach equilibrium state when it was carried out for 10h at 25°C. For the nucleophilic substitution of tosyl group with ethanolamine, the reaction was completed after 10h reaction at 50°C. The structures of products were characterized by NMR and FT-IR spectroscopy. The results showed that the p-toluenesulfonate esters can be effectively substituted by ethanolamine to form the hydroxyethyl amino hydroxypropyl guar gum (EAHPG). The content of nitrogen of EAHPG was determined by acid-base titration and element analysis.     

Synthesis of AZT analogues: 7-(3-azido-2hydroxypropyl)-, 7-(3-amino-2-hydroxypropyl)-, 7-(3-triazolyl-2-hydroxypropyl)theophyllines

Nucleophilic displacement of the tosyloxy group in 7-(2-hydroxy-3-p-toluenesulfonyloxypropyl)theophylline (1) with azide anion afforded 7-(3-azido-2-hydroxypropyl)theophylline (2). Reduction of the 3-azido group in 2 with Ph₃P/Py/NH₄OH afforded the 3-amino derivative 4, alternatively obtained by regioselective amination of 7-(2,3-epoxypropyl)theophylline (3). Selective acetylation of 4 gave the N-acetyl derivative 5. 1,3-Dipolar cycloaddition of the azide group in 2 with N¹-propargyl thymine (6) afforded the regioisomeric triazole 7.     

Characterization and intermolecular interactions of hydroxypropyl guar solutions

Aqueous solutions of guar galactomannan and hydroxypropyl guars (HPG) with different molar substitution (MS) levels were studied using dilute solution viscometry and gel permeation chromatography. When guar is modified to HPG, the added hydroxypropyl groups sterically block the hydrogen bonding sites on the guar backbone and reduce the hydrogen bonding attractions between guar molecules. The effects of molar substitution on the intermolecular interactions are inferred from measurements of the Huggins coefficients, which measure intermolecular interactions in dilute solution, and molecular volumes, which reflect intrachain associations. The behavior can be divided into three regimes: (1) at low MS levels (0 < MS < approximately 0.4), there is a sharp decrease in intermolecular interactions as a function of MS; (2) in the intermediate range ( approximately 0.4 < MS < approximately 1.0), interactions become independent of MS; (3) at high substitution levels (MS > approximately 1.0), the temperature dependence of inter- and intramolecular hydrophobic interactions produces a temperature dependence in the Huggins coefficient and molecular volumes that is not seen at lower substitutions. By acid hydrolysis, HPG samples with a range of molecular weights and consistent polydispersities were obtained. On the basis of these samples, the Mark-Houwink-Sakurada parameters and "characteristic ratio" C(infinity) were evaluated for HPG (MS approximately 0.6) and compared to the values for guar. The HPG chain stiffens as the degree of substitution increases.     

Extensional properties of hydroxypropyl ether guar gum solutions

The extensional properties of 2-hydroxypropyl ether guar gum solutions were investigated using a capillary breakup extensional rheometer (CaBER). Optimization of the geometric parameters of this device allowed for the measurement of the characteristic relaxation times and the apparent extensional viscosities of a series of dilute to semidilute guar gum solutions. The measured relaxation times were compared with predicted Zimm relaxation times, assuming that the hydrophobically modified guar was in a good solvent. Good agreement was found at low concentrations (0.01 wt % approximately 0.17 c*, where c* is the polymer overlap concentration), and this technique allowed for relaxation times on the order of 1 ms to be measured for solutions with shear viscosities of 2 mPa.s. Both the shear and (apparent) steady-state extensional viscosities of this set of industrially relevant fluids exhibited two regions of dependency on polymer concentration: linear up to concentrations of 0.2 wt % ( c/ c* approximately 3) and power law thereafter, where interchain interactions became significant. The extracted relaxation times followed the same trend (i.e., having a near linear dependency on concentration up to 0.2 wt % and a power-law dependency on concentration up to 9 c*). The results indicate that the transition from dilute to semidilute behavior occurs at a nominal concentration of approximately 3 c* instead of c*. The results presented suggest that interchain interactions for this modified guar are weak overall, and the solutions investigated are absent of entanglements over the whole range of frequencies and concentrations explored ((0.17-9) c*).     

Enzymatic acylation of hydroxypropyl cellulose in organic media and determination of ester formation by diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy

Esters were prepared by acylation of hydroxypropyl cellulose with fatty acid catalyzed by immobilized lipase from Candida antarctica in tert-butanol. The nature of the substrates used, the initial water activity of the system, and the molecular weight of the hydroxypropyl cellulose were investigated. Moreover, Fourier transform-infrared (FT-IR) spectroscopy was used for determination of ester content on hydroxypropyl cellulose. Specifically, a linear relationship was established between the peak height assigned to the absorption of the esterified carboxyl groups of the cellulose and the ester content. At optimum reaction conditions, the ester content on the hydroxypropyl cellulose was about 11%.     

Comb polymers prepared by ATRP from hydroxypropyl cellulose

Hydroxypropyl cellulose (HPC) was used as a core molecule for controlled grafting of monomers by ATRP, the aim being to produce densely grafted comb polymers. HPC was either allowed to react with an ATRP initiator or the first generation initiator-functionalized 2,2-bis(methylol)propionic acid dendron to create macroinitiators having high degrees of functionality. The macroinitiators were then "grafted from" using ATRP of methyl methacrylate (MMA) or hexadecyl methacrylate. Block copolymers were obtained by chain extending PMMA-grafted HPCs via the ATRP of tert-butyl acrylate. Subsequent selective acidolysis of the tert-butyl ester moieties was performed to form a block of poly(acrylic acid) resulting in amphiphilic block copolymer grafts. The graft copolymers were characterized by 1H NMR and FT-IR spectroscopies, DSC, TGA, rheological measurements, DLS, and tapping mode AFM on samples spin coated upon mica. It was found that the comb (co)polymers were in the nanometer size range and that the dendronization had an interesting effect on the rheological properties.     

Characterization of chemical substitution of hydroxypropyl cellulose using enzymatic degradation

The distribution of substituents along the polymer backbone will have a strong influence on the properties of modified cellulose. Endoglucanases were used to degrade a series of hydroxypropyl cellulose (HPC) derivatives with a high degree of substitution. The HPCs were characterized with cloud-point analysis prior to degradation. The extent of enzymatic degradation was determined with size-exclusion chromatography with online multi-angle light scattering and refractive index detection and also with high-pH anion exchange chromatography with pulsed amperometric detection. To further characterize the formed products, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry was employed for analysis of short-chained oligosaccharides. The different endoglucanases showed varying degradation capability depending on structure of the active site. The highly substituted HPCs had different susceptibility to degradation by the endoglucanases. The results show a difference in substituent distribution between HPCs, which would explain the differing cloud-point behaviors. Increased number of regions with low substitution could be correlated with lower polymer cloud point. The study shows the usefulness of enzymatic degradation to study the distribution of substituents in soluble biopolymer derivates.     

Effects of hydroxypropyl cyclodextrins on the reactivation of SDS-denatured aminoacylase

Cyclodextrins are natural-occurring circular oligosaccharides with an internal hydrophobic cavity and external hydrophilic edges. Because cyclodextrins bind with protein aromatic residues, they can prevent protein aggregation, and their ability to bind with detergents enables them to act as stripping reagents to release proteins from protein-detergent complexes. In this research, we investigated the effects of three hydroxypropyl cyclodextrins (HPCDs) on the refolding of aminoacylase from SDS-denatured states. It was found that the three HPCDs could effectively assist aminoacylase reactivation though they have different abilities. HP-gamma-CD, which has the largest cavity among the three HPCDs, was the most efficient one. Spectroscopic results further indicated that the secondary structure recovery of aminoacylase could be completed with the help of low concentrations of HPCDs. However, the activity of the released protein could not fully recover even though high concentrations of HPCDs were used. The concentration-dependent effects of HPCDs also indicated that cyclodextrins could also act as folding assistants in addition to acting as stripping reagents during the refolding of detergent-denatured proteins.