Self-assembled films of hemoglobin/laponite/chitosan: application for the direct electrochemistry and catalysis to hydrogen peroxide

A highly stable biological film was formed on the functional glassy carbon electrode (GCE) via step-by-step self-assembly of chitosan (CHT), laponite, and hemoglobin (Hb). Cyclic voltammetry (CV) of the Hb/laponite/CHT/GCE showed a pair of stable and quasi-reversible peaks for the Hb-Fe(III)/Fe(II) redox couple at about -0.035 V versus a saturated calomel electrode in pH 6.0 phosphate buffer at a scan rate of 0.1 V s(-1). The electrochemical reaction of Hb entrapped on the laponite/CHT self-assembled film exhibited a surface-controlled electrode process. The formal potential of the Hb-heme-Fe(III)/Fe(II) couple varied linearly with the increase of pH over the range of 3.0-8.0 with a slope of -63 mV pH(-1), which implied that an electron transfer was accompanied by single-proton transfer in the electrochemical reaction. The position of the Soret absorption band of this self-assembled Hb/laponite/CHT film suggested that the entrapped Hb kept its secondary structure similar to its native state. The self-assembled film showed excellent long-term stability, the CV peak potentials kept in the same positions, and the cathodic peak currents retained 90% of their values after 60 days. The film was used as a biological catalyst to catalyze the reduction of hydrogen peroxide. The electrocatalytic response showed a linear dependence on the H2O2 concentration ranging widely from 6.2 x 10(-6) to 2.55 x 10(-3) M with a detection limit of 6.2 x 10(-6) M at 3 sigma.     

Direct electrochemistry of hemoglobin based on chitosan–ionic liquid–ferrocene/graphene composite film

This paper described an ingenious approach for the fabrication of a promising biosensor, hemoglobin (Hb)/chitosan (Chit)–ionic liquid (IL)–ferrocene (Fc)/graphene (Gr)/glassy carbon electrode (GCE), that exploited the synergistic beneficial characteristics of Fc, Gr and IL for Hb. The proposed biosensor showed a strong electrocatalytic activity toward the reduction of H₂O₂, which could be attributed to the favored orientation of Hb in the well-confined surface as well as the high electrical conductivity of the resulting Chit–IL–Fc/Gr inorganic hybrid composite. The developed biosensor exhibited a fast amperometric response (2 s), a good linear response toward H₂O₂ over a wide range of concentration from 50 μM to 1200 μM, and a low detection limit of 3.8 μM. The apparent Michaelis–Menten constant (K_m) of Hb on the composite medium was 0.16 mM, showing high bioelectrocatalytic activity of immobilized protein toward H₂O₂ reduction. High sensitivity and stability, technically simple and possibility of preparation at short period of time are of great advantages of the developed biosensors.     

Direct electron transfer and enzymatic activity of hemoglobin in a hexagonal mesoporous silica matrix

The direct electrochemistry of hemoglobin (Hb) immobilized on a hexagonal mesoporous silica (HMS)-modified glassy carbon electrode was described. The interaction between Hb and the HMS was investigated using UV-Vis spectroscopy, FT-IR, and electrochemical methods. The direct electron transfer of the immobilized Hb exhibited two couples of redox peaks with the formal potentials of -0.037 and -0.232 V in 0.1 M (pH 7.0) PBS, respectively, which corresponded to its two immobilized states. The electrode reactions showed a surface-controlled process with a single proton transfer at the scan rate range from 20 to 200 mV/s. The immobilized Hb retained its biological activity well and displayed an excellent response to the reduction of both hydrogen peroxide (H2O2) and nitrate (NO2-). Its apparent Michaelis-Menten constants for H2O2 and NO2- were 12.3 and 49.3 microM, respectively, showing a good affinity. Based on the immobilization of Hb on the HMS and its direct electrochemistry, two novel biosensors for H2O2 and NO2- were presented. Under optimal conditions, the sensors could be used for the determination of H2O2 ranging from 0.4 to 6.0 microM and NO2- ranging from 0.2 to 3.8 microM. The detection limits were 1.86 x 10(-9) M and 6.11 x 10(-7) M at 3sigma, respectively. HMS provided a good matrix for protein immobilization and biosensor preparation.     

Direct electrochemistry and electrocatalysis of hemoglobin immobilized on carbon paste electrode by silica sol-gel film

Direct electrochemical and electrocatalytic behaviors of hemoglobin (Hb) immobilized on carbon paste electrode (CPE) by a silica sol-gel film derived from tetraethylorthosilicate (TEOS) were investigated for the first time. Hb/sol-gel film modified electrodes showed a pair of well-defined and nearly reversible cyclic voltammetric peaks for Hb Fe(III)/Fe(II) redox couple at about -0.312 V (versus Ag/AgCl) in a pH 7.0 phosphate buffer. The formal potential of Hb heme Fe(III)/Fe(II) couple varied linearly with the increase of pH in the range of 5.0-10.0 with a slope of 49.44 mV pH(-1), which suggests that a proton transfer is accompanied with each electron transfer (ET) in the electrochemical reaction. The immobilized Hb displayed the features of peroxidase and gave excellent electrocatalytic performance to the reduction of O2, NO2(-) and H2O2. The calculated apparent Michaelis-Menten constant was 8.98 x 10(-4)M, which indicated that there was a large catalytic activity of Hb immobilized on CPE by sol-gel film toward H2O2. In comparison with other electrodes, the chemically modified electrodes, used in this direct electrochemical study of Hb, are easy to be fabricated and rather inexpensive. Consequently, the Hb/sol-gel film modified electrode provides a convenient approach to perform electrochemical research on this kind of proteins. It also has potential use in the fabrication of the third generation biosensors and bioreactors.     

Urchinlike MnO2 nanoparticles for the direct electrochemistry of hemoglobin with carbon ionic liquid electrode

In this paper an urchinlike MnO(2) nanoparticle was synthesized by hydrothermal method and applied to the protein electrochemistry for the first time. By using a carbon ionic liquid electrode (CILE) as the basal electrode, hemoglobin (Hb) was immobilized on the surface of CILE with chitosan (CTS) and MnO(2) nanoparticle composite materials. Spectroscopic results indicated that Hb molecules retained its native structure in the composite film. A pair of well-defined redox peaks appeared on the cyclic voltammogram with the formal peak potential as -0.180 V (vs. SCE), which indicated that direct electron transfer of Hb was realized on the modified electrode. The result can be attributed to the specific characteristic of MnO(2) nanoparticle and the advantages of CILE, which facilitated the electron transfer rate. The fabricated CTS-MnO(2)-Hb/CILE showed good electrocatalytic ability to the reduction of trichloroacetic acid (TCA). Under the optimal conditions the catalytic current was in linear to TCA concentration in the range from 0.5 to 16.0 mmol L(-1) with the detection limit calculated as 0.167 mmol L(-1) (3σ). The result indicated that urchinlike MnO(2) nanoparticle had the potential application in the third generation electrochemical biosensors.     

A novel nitrite biosensor based on the direct electron transfer of hemoglobin immobilized on CdS hollow nanospheres

A novel nitrite biosensor based on the direct electron transfer of hemoglobin (Hb) immobilized on CdS hollow nanospheres (HS-CdS) modified glassy carbon electrode was constructed. The direct electron transfer of Hb showed a pair of redox peaks with a formal potential of -286 mV (vs. SCE) in 0.1M pH 7.0 phosphate buffer solution. It was a surface-controlled electrode process involving a single proton transfer coupled with a reversible one-electron transfer for each heme group of Hb. HS-CdS had a large specific surface area and good biocompatibility and had a better electrochemical response than that of solid spherical CdS. The immobilized Hb on HS-CdS displayed an excellent response to NO(2)(-) with one irreversible electrode process for NO reduction. Under optimal conditions, the biosensor could be used for the determination of NO(2)(-) with a linear range from 0.3 to 182 microM and a detection limit of 0.08 microM at 3 sigma based on the irreversible reduction of NO. HS-CdS provided a good matrix for protein immobilization and had a promising application in constructing sensors.     

Porous nanosheet-based ZnO microspheres for the construction of direct electrochemical biosensors

Nanosheet-based ZnO microsphere with porous nanostructures was synthesized by a facile chemical bath deposition method followed by thermal treatment, which was explored for the construction of electrochemical biosensors. Spectroscopic and electrochemical researches revealed the ZnO-based composite was a biocompatible immobilization matrix for enzymes with good enzymatic stability and bioactivity. With advantages of nanostructured inorganic-organic hybrid materials, a pair of stable and well-defined quasi-reversible redox peaks of hemoglobin was obtained with a formal potential of -0.345V (vs. Ag/AgCl) in pH 7.0 buffer. Facilitated direct electron transfer of the metalloenzymes with an apparent heterogeneous electron transfer rate constant (k(s)) of 3.2s(-1) was achieved on the ZnO-based enzyme electrode. Comparative studies demonstrated the nanosheet-based ZnO microspheres were more effective in facilitating the electron transfer of immobilized enzyme than solid ZnO microspheres, which may result from the unique nanostructures and larger surface area of the porous ZnO. The prepared biosensor displayed good performance for the detection of H(2)O(2) and NaNO(2) with a wide linear range of 1-410 and 10-2700muM, respectively. The entrapped hemoglobin exhibits high peroxidase-like activity for the catalytic reduction of H(2)O(2) with an apparent Michaelis-Menten constant (K(M)(app)) of 143muM. The nanosheet-based ZnO could be a promising matrix for the fabrication of direct electrochemical biosensors, and may find wide potential applications in biomedical detection and environmental analysis.     

Direct electron transfer and electrocatalysis of hemoglobin adsorbed on mesoporous carbon through layer-by-layer assembly

Using chitosan as an effective linker between CMK-3 and glassy carbon electrode surface, {Hb/CMK-3}n multilayer film-modified electrodes were constructed through layer-by-layer assembly. The morphology of thus-formed {Hb/CMK-3}n film was characterized by scanning electron micrographs, and the interaction of hemoglobin (Hb) with CMK-3 was studied by UV-vis spectroscopy and electrochemical methods. Under optimal conditions, {Hb/CMK-3}6 film showed a couple of stable and well-defined redox peaks at about -377 and -296 mV in pH 7.0 buffers. Furthermore, the {Hb/CMK-3}6 film displayed excellent electrocatalysis to the reduction of both H2O2 and O2. Based on thus-formed film and its direct electron transfer behavior, a novel biosensor was presented for the determination of H2O2 ranging from 1.2 to 57 muM with the detection limit of 0.6microM at S/N=3. CMK-3 provided a desirable matrix for protein immobilization and biosensor preparation.     

Composite system based on chitosan and room-temperature ionic liquid: direct electrochemistry and electrocatalysis of hemoglobin

A novel polymer/room-temperature ionic liquid (RTIL) composite material based on chitosan (Chi) and 1-butyl-3-methyl-imidazolium tetrafluoroborate (BMIM.BF(4)) was explored. The composite system can be readily used as an immobilization matrix to entrap proteins and enzymes. Hemoglobin (Hb) was chosen as a model protein to investigate the composite system. A pair of well-defined quasireversible redox peaks of hemoglobin were obtained at the Chi-BMIM.BF(4)-Hb composite-film-modified glassy carbon (GC) electrode by direct electron transfer between the protein and the GC electrode. Dramatically enhanced biocatalytic activity was exemplified at the Chi-BMIM.BF(4)-Hb/GC electrode by the reduction of oxygen and trichloroacetic acid. Thermogravimetric analysis (TGA) suggests that the Chi-BMIM.BF(4)-Hb composite has higher thermal stability than Chi-Hb itself. The Chi-BMIM.BF(4)-Hb film was also characterized by UV-visible spectra, indicating excellent stability in solution and good biocompatibility for protein. The unique composite material based on polymer and ionic liquid can find wide potential applications in direct electrochemistry, biosensors, and biocatalysis.     

Fabrication and characterization of non-enzymatic glucose sensor based on ternary NiO/CuO/polyaniline nanocomposite

Novel nickel and copper oxide nanoparticle modified polyaniline (PANI) nanofibers (NiO/CuO/PANI) were fabricated and used as a non-enzymatic sensor for detecting glucose. PANI nanofibers were prepared through electrodeposition, whereas nickel and copper oxide nanoparticles were deposited on PANI nanofibers by electrodeposition and electrochemical oxidation in situ. The morphology and structure of NiO/CuO/PANI nanocomposites were characterized by field emission scanning electron microscopy (FE–SEM), X-ray diffraction (XRD), Raman spectroscopy, and Fourier transform infrared (FT–IR). The as-prepared NiO/CuO/PANI electrode was employed for non-enzymatic glucose detection in alkaline electrolyte and showed better electrocatalytic activity compared with the PANI, CuO/PANI, and NiO/PANI electrodes. Consequently, an amperometric electrode of glucose was achieved under 0.6 V versus Ag/AgCl with a wide linear range from 20 to 2500 μM (R² = 0.9978) and a low detection limit of 2.0 μM (signal/noise [S/N] = 3). This electrode can effectively analyze glucose concentration in human serum samples, avoiding interference, and is a promising non-enzymatic glucose sensor due to its low overpotential, high sensitivity, good selectivity and stability, fast response, and low cost.     

Direct electrocatalytic oxidation of adenine and guanine on carbon ionic liquid electrode and the simultaneous determination

A carbon ionic liquid electrode (CILE) was fabricated by using an ionic liquid of N-butylpyridinium hexafluorophosphate (BPPF(6)) as binder and further used for the simultaneous detection of adenine and guanine. The direct electrooxidation behaviors of adenine and guanine were carefully investigated on the CILE. The results indicated that both adenine and guanine showed the increase of the oxidation peak currents with the negative shift of the oxidation peak potentials in contrast to that on the traditional carbon paste electrode (CPE). The electrochemical parameters of adenine and guanine on the CILE were calculated and a new electroanalytical method was established for the detection of adenine and guanine, respectively. The CILE exhibited good behaviors in the simultaneous detection of adenine and guanine with the peak separation as 0.304V. The measurements of thermally denatured single-stranded DNA (ssDNA) were further carried out and the value of (G+C)/(A+T) of ssDNA was calculated as 0.81.     

A novel NiO-Au hybrid nanobelts based sensor for sensitive and selective glucose detection

A novel amperometric nonenzymatic glucose sensor based on Au-doped NiO nanobelts has been successfully fabricated and applied to nonenzymatic glucose detection. Its electrochemical behavior towards the oxidation of glucose was compared with NiO nanofibers and Au microparticles prepared with a similar procedure. The NiO-Au hybrid nanobelts modified electrode displays greatly enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the matrix NiO and the doped Au. The as-prepared NiO-Au nanobelts based glucose sensor displays significantly lower onset potential, lower detection limit, higher sensitivity, and wider linear range than that of pristine NiO nanofibers modified electrode. Moreover, Au nanoparticles distributed in NiO nanofibers enabled amperometric glucose detection with insignificant interference from ascorbic acid and uric acid. These results indicate that the NiO-Au hybrid nanobelt is a promising candidate in the development of highly sensitive and selective nonenzymatic glucose sensors.     

Investigation of the chloride effect on hemoglobin by adsorptive transfer voltammetry

A strategy of ex situ electrochemical method has been proposed for investigating the chloride effect on hemoglobin (Hb). Unlike the common electrochemical method that measures the chloride effect on Hb in bulk solution (in situ), the effects of chloride anion on Hb were investigated ex situ by adsorptive transfer voltammetry (AdTV) in this work. Gold electrode modified by self-assembled monolayer of 3-mercaptopropanoic acid (AuE/MPA) was prepared and then incubated in a series of Hb solutions containing different concentrations of chloride anion for adsorbing Hb-Cl (AuE/MPA/Hb-Cl). The resulting electrode was then measured in phosphate buffer solution by cyclic voltammetry. The corresponding voltammograms showed obvious promotion of the direct electron transfer of Hb with remarkable increase of peak currents, decrease of peak-to-peak separations, and negative shift of the formal potentials. As complementation, the adsorption behavior of Hb-Cl on AuE/MPA, the structural information of Hb-Cl, and the electrocatalytic ability of AuE/MPA/Hb-Cl toward hydrogen peroxide were investigated by surface plasmon resonance, circular dichroism spectrum, ultraviolet-visible spectrum and amperometry, respectively. The results indicate that the chloride effect resulted in more electroactive sites of Hb on the surface of electrode. Meanwhile, the specific and nonspecific interactions between Hb and chloride anion can be discriminated from the electrochemical parameters obtained by AdTV.     

Electrodeposition of gold-platinum alloy nanoparticles on ionic liquid-chitosan composite film and its application in fabricating an amperometric cholesterol biosensor

An electrodeposition method was applied to form gold-platinum (AuPt) alloy nanoparticles on the glassy carbon electrode (GCE) modified with a mixture of an ionic liquid (IL) and chitosan (Ch) (AuPt-Ch-IL/GCE). AuPt nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods. AuPt-Ch-IL/GCE electrocatalyzed the reduction of H(2)O(2) and thus was suitable for the preparation of biosensors. Cholesterol oxidase (ChOx) was then, immobilized on the surface of the electrode by cross-linking ChOx and chitosan through addition of glutaraldehyde (ChOx/AuPt-Ch-IL/GCE). The fabricated biosensor exhibited two wide linear ranges of responses to cholesterol in the concentration ranges of 0.05-6.2 mM and 6.2-11.2 mM. The sensitivity of the biosensor was 90.7 μA mM(-1) cm(-2) and the limit of detection was 10 μM of cholesterol. The response time was less than 7 s. The Michaelis-Menten constant (K(m)) was found as 0.24 mM. The effect of the addition of 1 mM ascorbic acid and glucose was tested on the amperometric response of 0.5 mM cholesterol and no change in response current of cholesterol was observed.     

Amperometric third-generation hydrogen peroxide biosensor based on the immobilization of hemoglobin on multiwall carbon nanotubes and gold colloidal nanoparticles

A convenient and effective strategy for preparation nanohybrid film of multi-wall carbon nanotubes (MWNT) and gold colloidal nanoparticles (GNPs) by using proteins as linker is proposed. In such a strategy, hemoglobin (Hb) was selected as model protein to fabricate third-generation H2O2 biosensor based on MWNT and GNPs. Acid-pretreated, negatively charged MWNT was first modified on the surface of glassy carbon (GC) electrode, then, positively charged Hb was adsorbed onto MWNT films by electrostatic interaction. The {Hb/GNPs}n multilayer films were finally assembled onto Hb/MWNT film through layer-by-layer assembly technique. The assembly of Hb and GNPs was characterized with cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and transmission electron microscopy (TEM). The direct electron transfer of Hb is observed on Hb/GNPs/Hb/MWNT/GC electrode, which exhibits excellent electrocatalytic activity for the reduction of H2O2 to construct a third-generation mediator-free H2O2 biosensor. As compared to those H2O2 biosensors only based on carbon nanotubes, the proposed biosensor modified with MWNT and GNPs displays a broader linear range and a lower detection limit for H2O2 determination. The linear range is from 2.1x10(-7) to 3.0x10(-3) M with a detection limit of 8.0x10(-8) M at 3sigma. The Michaelies-Menten constant KMapp value is estimated to be 0.26 mM. Moreover, this biosensor displays rapid response to H2O2 and possesses good stability and reproducibility.     

Myoglobin immobilization on electrodeposited nanometer-scale nickel oxide particles and direct voltammetry

Prosperity of information on the reactions of redox-active sites in proteins can be attained by voltammetric studies in which the protein sample is located on a suitable surface. This work reports the presentation of myoglobin/nickel oxide nanoparticles/glassy carbon (Mb/NiO NPs/GC) electrode, ready by electrochemical deposition of the NiO NPs on glassy carbon electrode and myoglobin immobilization on their surfaces by the potential cycling method. Images of electrodeposited NiO NPs on the surface of glassy carbon electrode were obtained by scanning electron microscopy (SEM) and atomic force microscopy (AFM). A pair of well-defined redox peaks for Mb(Fe(III)-Fe(II)) was obtained at the prepared electrode by direct electron transfer between the protein and nanoparticles. Electrochemical parameters of immobilized myoglobin such as formal potential (E(0')), charge transfer coefficient (alpha) and apparent heterogeneous electron transfer rate constant (k(s)) were estimated by cyclic voltammetry and nonlinear regression analysis. Biocatalytic activity was exemplified at the prepared electrode for reduction of hydrogen peroxide.     

Direct electrochemistry of hemoglobin immobilized on gold electrode by Langmuir-Blodgett technique

In this research, we reported a novel method of forming hemoglobin (Hb)-linoleic acid (LA) Langmuir-Blodgett (LB) monolayer by spreading Hb solution directly onto the subphase covered with a layer of LA. This method is suitable for preparing electrochemical devices with protein-lipid LB film because almost no protein adsorbed on electrode surface before protein-lipid film transferred from air-water interface to electrode, which ensured better electrode activity. The compressibility of Hb-LA monolayer was used to character the phase transition during compression process. Optimal experimental conditions were obtained by analyzing pressure-time, pressure-area and pressure-compressibility curves. The direct electrochemistry of Hb, which was immobilized on Au electrode surface incorporated with LA layer by LB method, was investigated using cyclic voltammetry for the first time. The electrode modified with Hb-LA LB film holds high electrochemical activity and shows a fast direct electron transfer of Hb. Redox peak currents increased linearly with the increase of scan rate, indicating a surface-controlled electrode process. The electron transfer rate constant was 2.68+/-0.45 s-1. As a target of this research, this work provides a new way to prepare biomimetic film and biosensor.     

A novel hydrogen peroxide biosensor based on the immobilization of hemoglobin on three-dimensionally ordered macroporous (3DOM) gold-nanoparticle-doped titanium dioxide (GTD) film

The three-dimensionally ordered macroporous gold-nanoparticle-doped titanium dioxide (3DOM GTD) film was modified on the indium-tin oxide (ITO) electrode surface. Hemoglobin (Hb) has been successfully immobilized on the 3DOM GTD film and the fabrication process was characterized by Raman and UV-vis spectra. The results indicated that the Hb immobilized on the film retained its biological activity and the secondary structure of Hb was not destroyed. The direct electrochemistry and electrocatalysis of Hb immobilized on this film have been investigated. The Hb/3DOM GTD/ITO electrode exhibited two couples of redox peaks corresponding to the Hb intercalated in the mesopores and adsorbed on the external surface of the film with the formal potential of -0.20 and -0.48 V in 0.1M PBS (pH7.0), respectively. The Hb/3DOM GTD/ITO electrode exhibits an excellent eletrocatalytic activity, a wide linear range for H(2)O(2) from 5.0 μM to 1.0mM with a limit of detection of 0.6μM, high sensitivity (144.5 μA mM(-1)), good stability and reproducibility. Compared with the TiO(2) nanoneedles modified electrode, the GTD modified electrode has higher sensitivity and response peak current. The 3DOM GTD provided a good matrix for bioactive molecules immobilization, suggesting it has the potential use in the fields of H(2)O(2) biosensors.     

Ionic liquid-carbon composite glucose biosensor

The use of ionic liquids that are solid at room temperature such as n-octyl-pyridinium hexafluorophosphate (nOPPF(6)) is shown to be advantageous in the fabrication of new form of biocomposite materials with attractive performance over other types of composites and pastes involving non-conductive binders. The resulting IL/graphite material brings new capabilities for electrochemical devices by combining the advantages of ILs and "bulk" composite electrodes. The electrocatalytic properties of the ILs are not impaired by their association with the graphite powder. The marked electrocatalytic activity towards hydrogen peroxide permits effective amperometric biosensing of glucose in connection with the incorporation of glucose oxidase within the three-dimensional IL/graphite matrix. The accelerated electron transfer is coupled with low background current and improved linearity. The advantages of these IL-based biocomposite devices are illustrated from comparison to conventional mineral oil/graphite biocomposite. The influence of the IL and glucose oxidase (GOx) loading upon the amperometric and voltammetric data, as well as the electrode capacitance and resistance, is examined. The preparation of IL/graphite composites overcomes a major obstacle for creating IL-based biosensing devices and expands the scope of IL-based electrochemical devices.     

Electrochemical investigation of immobilized hemoglobin: redox chemistry and enzymatic catalysis

Hb entrapped in the Konjak glucomannan (KGM) film could transfer electrons directly to an edge-plane pyrolytic graphite (EPG) electrode, corresponding to the redox couple of Fe(III)/Fe(II). The redox properties of Hb, such as formal potential, electron transfer rate constant, the stability of the redox state of protein and redox Bohr effect, were characterized by cyclic voltammetry and square wave voltammetry. The stable Hb-KGM/EPG gave analytically useful electrochemical catalytic responses to oxygen, hydrogen peroxide and nitrite.