Recent advances in the separators for microbial fuel cells

Separator plays an important role in microbial fuel cells (MFCs). Despite of the rapid development of separators in recent years, there are remaining barriers such as proton transfer limitation and oxygen leakage, which increase the internal resistance and decrease the MFC performance, and thus limit the practical application of MFCs. In this review, various separator materials, including cation exchange membrane, anion exchange membrane, bipolar membrane, microfiltration membrane, ultrafiltration membranes, porous fabrics, glass fibers, J-Cloth and salt bridge, are systematically compared. In addition, recent progresses in separator configuration, especially the development of separator electrode assemblies, are summarized. The advances in separator materials and configurations have opened up new promises to overcome these limitations, but challenges remain for the practical application. Here, an outlook for future development and scaling-up of MFC separators is presented and some suggestions are highlighted.     

Performance and microbial ecology of air-cathode microbial fuel cells with layered electrode assemblies

Microbial fuel cells (MFCs) can be built with layered electrode assemblies, where the anode, proton exchange membrane (PEM), and cathode are pressed into a single unit. We studied the performance and microbial community structure of MFCs with layered assemblies, addressing the effect of materials and oxygen crossover on the community structure. Four MFCs with layered assemblies were constructed using Nafion or Ultrex PEMs and a plain carbon cloth electrode or a cathode with an oxygen-resistant polytetrafluoroethylene diffusion layer. The MFC with Nafion PEM and cathode diffusion layer achieved the highest power density, 381 mW/m² (20 W/m³). The rates of oxygen diffusion from cathode to anode were three times higher in the MFCs with plain cathodes compared to those with diffusion-layer cathodes. Microsensor studies revealed little accumulation of oxygen within the anode cloth. However, the abundance of bacteria known to use oxygen as an electron acceptor, but not known to have exoelectrogenic activity, was greater in MFCs with plain cathodes. The MFCs with diffusion-layer cathodes had high abundance of exoelectrogenic bacteria within the genus Geobacter. This work suggests that cathode materials can significantly influence oxygen crossover and the relative abundance of exoelectrogenic bacteria on the anode, while PEM materials have little influence on anode community structure. Our results show that oxygen crossover can significantly decrease the performance of air-cathode MFCs with layered assemblies, and therefore limiting crossover may be of particular importance for these types of MFCs.     

Convergent development of anodic bacterial communities in microbial fuel cells

Microbial fuel cells (MFCs) are often inoculated from a single wastewater source. The extent that the inoculum affects community development or power production is unknown. The stable anodic microbial communities in MFCs were examined using three inocula: a wastewater treatment plant sample known to produce consistent power densities, a second wastewater treatment plant sample, and an anaerobic bog sediment. The bog-inoculated MFCs initially produced higher power densities than the wastewater-inoculated MFCs, but after 20 cycles all MFCs on average converged to similar voltages (470±20 mV) and maximum power densities (590±170 mW m⁻²). The power output from replicate bog-inoculated MFCs was not significantly different, but one wastewater-inoculated MFC (UAJA3 (UAJA, University Area Joint Authority Wastewater Treatment Plant)) produced substantially less power. Denaturing gradient gel electrophoresis profiling showed a stable exoelectrogenic biofilm community in all samples after 11 cycles. After 16 cycles the predominance of Geobacter spp. in anode communities was identified using 16S rRNA gene clone libraries (58±10%), fluorescent in-situ hybridization (FISH) (63±6%) and pyrosequencing (81±4%). While the clone library analysis for the underperforming UAJA3 had a significantly lower percentage of Geobacter spp. sequences (36%), suggesting that a predominance of this microbe was needed for convergent power densities, the lower percentage of this species was not verified by FISH or pyrosequencing analyses. These results show that the predominance of Geobacter spp. in acetate-fed systems was consistent with good MFC performance and independent of the inoculum source.     

Economical Speed and Energetically Optimal Transition Speed Evaluated by Gross and Net Oxygen Cost of Transport at Different Gradients

The oxygen cost of transport per unit distance (CoT; mL·kg^-1·km^-1) shows a U-shaped curve as a function of walking speed (v), which includes a particular walking speed minimizing the CoT, so called economical speed (ES). The CoT-v relationship in running is approximately linear. These distinctive walking and running CoT-v relationships give an intersection between U-shaped and linear CoT relationships, termed the energetically optimal transition speed (EOTS). This study investigated the effects of subtracting the standing oxygen cost for calculating the CoT and its relevant effects on the ES and EOTS at the level and gradient slopes (±5%) in eleven male trained athletes. The percent effects of subtracting the standing oxygen cost (4.8 ± 0.4 mL·kg^-1·min^-1) on the CoT were significantly greater as the walking speed was slower, but it was not significant at faster running speeds over 9.4 km·h^-1. The percent effect was significantly dependent on the gradient (downhill > level > uphill, P < 0.001). The net ES (level 4.09 ± 0.31, uphill 4.22 ± 0.37, and downhill 4.16 ± 0.44 km·h^-1) was approximately 20% slower than the gross ES (level 5.15 ± 0.18, uphill 5.27 ± 0.20, and downhill 5.37 ± 0.22 km·h^-1, P < 0.001). Both net and gross ES were not significantly dependent on the gradient. In contrast, the gross EOTS was slower than the net EOTS at the level (7.49 ± 0.32 vs. 7.63 ± 0.36 km·h^-1, P = 0.003) and downhill gradients (7.78 ± 0.33 vs. 8.01 ± 0.41 km·h^-1, P < 0.001), but not at the uphill gradient (7.55 ± 0.37 vs. 7.63 ± 0.51 km·h^-1, P = 0.080). Note that those percent differences were less than 2.9%. Given these results, a subtraction of the standing oxygen cost should be carefully considered depending on the purpose of each study.     

Stable Li–Organic Batteries with Nafion‐Based Sandwich‐Type Separators

Similar to Li–S batteries, Li–organic batteries have also been plagued by the dissolution of active materials and the resulting shuttle effect for many years. An effective strategy to eliminate the shuttle effect is adopting solid electrolytes or Li–ion permselective separators to prohibit the dissolved electroactive species from migrating to the Li anode. A polypropylene/Nafion/polypropylene (PNP) sandwich‐type separator is reported with many advantages in comparison with previously reported LISICON, polymer electrolyte, and other Nafion utilization forms. The physical and chemical properties of PNP separators are studied in detail by cross‐section scanning electron microscopy (SEM), infrared spectroscopy (IR), and electrochemical impedance spectroscopy. 1,1′‐Iminodianthraquinone (IDAQ), a novel organic cathode, is taken as an example to quantitatively investigate the function of PNP separators. In the presence of PNP5 with the most appropriate Nafion loading of 0.5 mg cm^–2, IDAQ is able to achieve dramatically improved cycling stability with capacity retention of 76% after 400 cycles and Coulombic efficiency above 99.6%, which reaches the highest level for reported soluble organic electrode materials. Besides Li–organic batteries, such kind of Nafion‐based sandwich‐type separators are also promising for Li–S batteries and other new battery designs involving dissolved electroactive species.     

Adaptation of Phytoplankton-Degrading Microbial Communities to Thermal Reactor Effluent in a New Cooling Reservoir

In water column and sediment inocula from a nuclear reactor cooling reservoir, natural phytoplankton substrate labeled with ¹⁴C was used to determine aerobic and anaerobic mineralization rates for a range of temperatures (25, 40, 55, and 70°C) expected during reactor operation. For experiments that were begun during reactor shutdown, aerobic decomposition occurred at temperatures of <55°C. After 2 months of reactor operation, aerobic rates increased substantially at 55 and 70°C, although maximum rates were observed at temperatures of ≤40°C. The temperature range for which maximum anaerobic mineralization (i.e., the sum of CH₄ and CO₂) was observed was 25 to 40°C when the reactor was off, expanding to 25 to 55°C during reactor operation. Increased rates at 55°C, but not 70°C, correlated with an increase in the ratio of cumulative methane to carbon dioxide produced over 21 days. When reduced reactor power lowered the maximum temperature of the reservoir to 42°C, aerobic decomposition at 70°C was negligible, but remained substantial at 55°C. Selection for thermophilic decomposers occurred rapidly in this system in both aerobic and anaerobic communities and did not require prolonged exposure to elevated temperatures.     

Scalable air cathode microbial fuel cells using glass fiber separators, plastic mesh supporters, and graphite fiber brush anodes

The combined use of brush anodes and glass fiber (GF1) separators, and plastic mesh supporters were used here for the first time to create a scalable microbial fuel cell architecture. Separators prevented short circuiting of closely-spaced electrodes, and cathode supporters were used to avoid water gaps between the separator and cathode that can reduce power production. The maximum power density with a separator and supporter and a single cathode was 75 ± 1 W/m³. Removing the separator decreased power by 8%. Adding a second cathode increased power to 154 ± 1 W/m³. Current was increased by connecting two MFCs connected in parallel. These results show that brush anodes, combined with a glass fiber separator and a plastic mesh supporter, produce a useful MFC architecture that is inherently scalable due to good insulation between the electrodes and a compact architecture.     

A study of lipid bilayer membrane stability using precise measurements of specific capacitance

A method is described for measuring the specific capacitance (C_m) of lipid bilayer membranes with an estimated experimental error of only 1%. The gross capacitance was measured with an AC Wheatstone bridge and a photographic technique was used to determine the area of thin membrane. The results of measurements on oxidized cholesterol-decane membranes formed in 1 × 10^-2 M KCl show that C_m depends upon temperature, voltage, time, and the age of the bulk membrane solutions. For a freshly thinned membrane (from 5 week old solution), C_m increases exponentially from an initial value of 0.432 ±0.021 (SD) μF/cm² with a time constant of ~15 min. A 100 mv potential applied across the membrane for 10-20 min prior to making measurements eliminated this time dependence and produced final-state membranes. C_m of final-state membranes depends upon applied voltage (V_a) and obeys the equation C_m = C₀ + βV_a² where V_a V_DC + V^rms_AC. C₀ and β depend upon temperature; C₀ decreases linearly with temperature while β increases linearly. At 20°C, C₀ = 0.559 ±0.01 (SD) μF/cm² and β = 0.0123 ±0.0036 (SD) (μF/cm²)/(mv²) and at 34°C, C₀ = 0.472 ±0.01 and β = 0.0382 ±0.0039. These variations in C_m are interpreted as resulting from thickness changes. The possibility that they result from diffuse layer and/or membrane dielectric phenomena is discussed and found to be unlikely. The results are discussed in terms of membrane stability by constructing hypothetical potential energy vs. thickness curves.     

THE EFFECTS OF INJURY PREVENTION WARM-UP PROGRAMMES ON KNEE STRENGTH IN MALE SOCCER PLAYERS

The study investigates the effects of the 11+ and HarmoKnee injury prevention programmes on knee strength in male soccer players. Under-21-year-old players (n=36) were divided equally into: the 11+, HarmoKnee and control groups. The programmes were performed for 24 sessions (20-25 min each). The hamstrings and quadriceps strength were measured bilaterally at 60°·s^-1, 180°·s^-1 and 300°·s^-1. The concentric quadriceps peak torque (PT) of the 11+ increased by 27.7% at 300°·s^-1 in the dominant leg (p<0.05). The concentric quadriceps PT of HarmoKnee increased by 36.6%, 36.2% and 28% in the dominant leg, and by 31.3%, 31.7% and 20.05% at 60°·s^-1, 180°·s^-1 and 300°·s^-1 in the non-dominant leg respectively. In the 11+ group the concentric hamstring PT increased by 22%, 21.4% and 22.1% at 60°·s^-1, 180°·s^-1 and 300°·s^-1, respectively in the dominant leg, and by 22.3%, and 15.7% at 60°·s^-1 and 180°·s^-1, in the non-dominant leg. In the HarmoKnee group the hamstrings in the dominant leg showed an increase in PT by 32.5%, 31.3% and 14.3% at 60°·s^-1, 180°·s^-1 and 300°·s^-1, and in the non-dominant leg hamstrings PT increased by 21.1% and 19.3% at 60°·s^-1 and 180°·s^-1 respectively. The concentric hamstrings strength was significantly different between the 11+ and control groups in the dominant (p=0.01) and non-dominant legs (p=0.02). The HarmoKnee programme enhanced the concentric strength of quadriceps. The 11+ and HarmoKnee programmes are useful warm-up protocols for improving concentric hamstring strength in young professional male soccer players. The 11+ programme is more advantageous for its greater concentric hamstring strength improvement compared to the HarmoKnee programme.     

Air-cathode structure optimization in separator-coupled microbial fuel cells

Microbial fuel cells (MFC) with 30% wet-proofed air cathodes have previously been optimized to have 4 diffusion layers (DLs) in order to limit oxygen transfer into the anode chamber and optimize performance. Newer MFC designs that allow close electrode spacing have a separator that can also reduce oxygen transfer into the anode chamber, and there are many types of carbon wet-proofed materials available. Additional analysis of conditions that optimize performance is therefore needed for separator-coupled MFCs in terms of the number of DLs and the percent of wet proofing used for the cathode. The number of DLs on a 50% wet-proofed carbon cloth cathode significantly affected MFC performance, with the maximum power density decreasing from 1427 to 855 mW/m² for 1–4 DLs. A commonly used cathode (30% wet-proofed, 4 DLs) produced a maximum power density (988 mW/m²) that was 31% less than that produced by the 50% wet-proofed cathode (1 DL). It was shown that the cathode performance with different materials and numbers of DLs was directly related to conditions that increased oxygen transfer. The coulombic efficiency (CE) was more affected by the current density than the oxygen transfer coefficient for the cathode. MFCs with the 50% wet-proofed cathode (2 DLs) had a CE of >84% (6.8 A/m²), which was substantially larger than that previously obtained using carbon cloth air-cathodes lacking separators. These results demonstrate that MFCs constructed with separators should have the minimum number of DLs that prevent water leakage and maximize oxygen transfer to the cathode.     

Electrical Properties and Acetylcholine Sensitivity of Singly and Multiply Innervated Avian Muscle Fibers

Membrane constants and distribution of acetylcholine (ACh) receptors were determined for multiply innervated fibers of the anterior latissimus dorsi (ALD) and singly innervated fibers of the posterior latissimus dorsi (PLD) muscles of 3–6 month old chickens. The values of the various membrane constants were: length constant, 1.78 mm (mean) in ALD, 0.68 mm in PLD; time constant, 35 msec in ALD, 3.7 msec in PLD; transverse membrane resistance, 4388 Ω cm² in ALD, 561 Ω cm² in PLD; and membrane capacitance, 8.2 µF/cm² in ALD, 7.0 µF/cm² in PLD. Peaks of ACh sensitivity occurred at intervals of ca. 740 µ on ALD fibers with a low sensitivity remaining between peaks. Only one peak of ACh sensitivity was detected on PLD fibers. The maximum ACh sensitivity found was 5 ± 4 mv/ncoul for fibers of the ALD and 77 ± 60 mv/ncoul for fibers of the PLD. The distance over which this sensitivity fell to 0.1 was ca. 225 µ in the ALD and 140 µ in the PLD. The membranes of these two muscle fiber types differ widely regarding some electrical properties and the disposition of ACh-sensitive receptor sites.     

Membrane Potential of Brown Adipose Tissue : A suggested mechanism for the regulation of thermogenesis

Membrane potentials were recorded in isolated segments of interscapular brown adipose tissue from rats. After equilibration at 29°C in Krebs-Ringer bicarbonate buffer a mean value of -51 ± 4 mv (SD) was found. This level could be maintained for up to 5 hr. The mean effective membrane resistance was 1.35 ± 0.45 megohm. The membrane potential was a function of the extracellular potassium concentration. Ouabain (10^-6-10^-3 M) and incubation in K-free buffer produced progressive depolarization. Epinephrine and norepinephrine in concentrations as low as 10^-8 g/ml produced a prompt depolarization. Cooling of the tissue and lowering of the oxygen tension caused a marked and reversible decrease in the membrane potential. In tissue obtained from cold-adapted rats, the membrane potential was considerably diminished. 6Assuming that the membrane potential is some function of the Na permeability of the plasma membrane it is suggested that an increase in the rate of active Na-K transport and ensuing ADP formation might contribute to the increase in respiration seen during exposure to thermogenic stimuli.     

Soluble Methane Monooxygenase Production and Trichloroethylene Degradation by a Type I Methanotroph, Methylomonas methanica 68-1

A methanotroph (strain 68-1), originally isolated from a trichloroethylene (TCE)-contaminated aquifer, was identified as the type I methanotroph Methylomonas methanica on the basis of intracytoplasmic membrane ultrastructure, phospholipid fatty acid profile, and 16S rRNA signature probe hybridization. Strain 68-1 was found to oxidize naphthalene and TCE via a soluble methane monooxygenase (sMMO) and thus becomes the first type I methanotroph known to be able to produce this enzyme. The specific whole-cell sMMO activity of 68-1, as measured by the naphthalene oxidation assay and by TCE biodegradation, was comparatively higher than sMMO activity levels in Methylosinus trichosporium OB3b grown in the same copper-free conditions. The maximal naphthalene oxidation rates of Methylomonas methanica 68-1 and Methylosinus trichosporium OB3b were 551 ± 27 and 321 ± 16 nmol h^-1 mg of protein ^-1, respectively. The maximal TCE degradation rates of Methylomonas methanica 68-1 and Methylosinus trichosporium OB3b were 2,325 ± 260 and 995 ± 160 nmol h^-1 mg of protein^-1, respectively. The substrate affinity of 68-1 sMMO to naphthalene (K_m, 70 ± 4 μM) and TCE (K_m, 225 ± 13 μM), however, was comparatively lower than that of the sMMO of OB3b, which had affinities of 40 ± 3 and 126 ± 8 μM, respectively. Genomic DNA slot and Southern blot analyses with an sMMO gene probe from Methylosinus trichosporium OB3b showed that the sMMO genes of 68-1 have little genetic homology to those of OB3b. This result may indicate the evolutionary diversification of the sMMOs.     

Interaction of lipophorin with Rhodnius prolixus oocytes: biochemical properties and the importance of blood feeding

Lipophorin (Lp) is the main haemolymphatic lipoprotein in insects and transports lipids between different organs. In adult females, lipophorin delivers lipids to growing oocytes. In this study, the interaction of this lipoprotein with the ovaries of Rhodnius prolixus was characterised using an oocyte membrane preparation and purified radiolabelled Lp ⁽¹²⁵I-Lp). Lp-specific binding to the oocyte membrane reached equilibrium after 40-60 min and when ¹²⁵I-Lp was incubated with increasing amounts of membrane protein, corresponding increases in Lp binding were observed. The specific binding of Lp to the membrane preparation was a saturable process, with a K_dof 7.1 ± 0.9 x 10^-8M and a maximal binding capacity of 430 ± 40 ng ¹²⁵I-Lp/µg of membrane protein. The binding was calcium independent and pH sensitive, reaching its maximum at pH 5.2-5.7. Suramin inhibited the binding interaction between Lp and the oocyte membranes, which was completely abolished at 0.5 mM suramin. The oocyte membrane preparation from R. prolixus also showed binding to Lp from Manduca sexta. When Lp was fluorescently labelled and injected into vitellogenic females, the level of Lp-oocyte binding was much higher in females that were fed whole blood than in those fed blood plasma.     

Biophysics of Active Vesicle Transport,an Intermediate Step That Couples Excitation and Exocytosis of Serotonin in the Neuronal Soma

Transmitter exocytosis from the neuronal soma is evoked by brief trains of high frequency electrical activity and continues for several minutes. Here we studied how active vesicle transport towards the plasma membrane contributes to this slow phenomenon in serotonergic leech Retzius neurons, by combining electron microscopy, the kinetics of exocytosis obtained from FM1-43 dye fluorescence as vesicles fuse with the plasma membrane, and a diffusion equation incorporating the forces of local confinement and molecular motors. Electron micrographs of neurons at rest or after stimulation with 1 Hz trains showed cytoplasmic clusters of dense core vesicles at 1.5±0.2 and 3.7±0.3 µm distances from the plasma membrane, to which they were bound through microtubule bundles. By contrast, after 20 Hz stimulation vesicle clusters were apposed to the plasma membrane, suggesting that transport was induced by electrical stimulation. Consistently, 20 Hz stimulation of cultured neurons induced spotted FM1-43 fluorescence increases with one or two slow sigmoidal kinetics, suggesting exocytosis from an equal number of vesicle clusters. These fluorescence increases were prevented by colchicine, which suggested microtubule-dependent vesicle transport. Model fitting to the fluorescence kinetics predicted that 52–951 vesicles/cluster were transported along 0.60–6.18 µm distances at average 11–95 nms⁻¹ velocities. The ATP cost per vesicle fused (0.4–72.0), calculated from the ratio of the ΔG_process/ΔG_ATP, depended on the ratio of the traveling velocity and the number of vesicles in the cluster. Interestingly, the distance-dependence of the ATP cost per vesicle was bistable, with low energy values at 1.4 and 3.3 µm, similar to the average resting distances of the vesicle clusters, and a high energy barrier at 1.6–2.0 µm. Our study confirms that active vesicle transport is an intermediate step for somatic serotonin exocytosis by Retzius neurons and provides a quantitative method for analyzing similar phenomena in other cell types.     

THE LYSOSOME PERIPHERY: BIOCHEMICAL AND ELECTROKINETIC PROPERTIES OF THE TRITOSOME SURFACE

Normal rat liver lysosomes were isolated by the technique of loading with Triton WR-1339. Purity of the preparation was monitored with marker enzymes; a high enrichment in acid hydrolases was obtained in the tritosome fraction. In 0.0145 M NaCl, 4.5% sorbitol, 0.6 mM NaHCO₃, pH 7.2 at 25°C the tritosomes had an electrophoretic mobility of -1.77 ± 0.02 µm/s/V/cm, a zeta potential of 23.2 mV, a surface charge of 1970 esu/cm², and 33,000 electrons per particle surface assuming a tritosome diameter of 5 x 10^-7 m. Treatment of the tritosomes with 50 µg neuraminidase/mg tritosome protein lowered the electrophoretic mobility of the tritosome to -1.23 ± 0.02 µm/s/V/cm under the same conditions and caused the release of 2.01 µg sialic acid/mg tritosome protein. Treatment of the tritosomes with hyaluronidase did not affect their electrophoretic mobility, while trypsin treatment elevated the net negative electrophoretic mobility of the tritosomes. Tritosome electrophoretic mobilities indicated a homogeneous tritosome population and varied greatly with ionic strength of the suspending media. pH vs. electrophoretic mobility curves indicated the tritosome periphery to contain an acid-dissociable group which likely represents the carboxyl group of N-acetylneuraminic acid; this was not conclusively proven, however, since the tritosomes lysed below a pH of 4 in the present system. Total tritosome carbohydrate (anthrone-positive material as glucose equivalents) was 0.19 mg/mg tritosome protein while total sialic acid was 3.8 µg (11.4 nmol)/mg tritosome protein. A tritosome "membrane" fraction was prepared by osmotic shock, homogenization, and sedimentation. Approximately 25% of the total tritosome protein was present in this fraction. Analysis by gas-liquid chromatography and amino acid analyzer showed the following carbohydrate composition of the tritosome membrane fraction (in microgram per milligram tritosome membrane protein): N-acetylneuraminic acid, 14.8 ± 3; glucosamine, 24 ± 3; galactosamine, 10 ± 2; glucose, 21 ± 2; galactose, 26 ± 2; mannose, 31 ± 5; fucose, 7 ± 1; xylose, 0; and arabinose, 0. The results indicate that the tritosome periphery is characterized by external terminal sialic acid residues and an extensive complement of glycoconjugates. Essentially all the tritosome N-acetylneuraminic acid is located in the membrane and about 53% of it is neuraminidase susceptible.     

Pharmacokinetics and Bioequivalence of Two Formulations of Febuxostat 40-Mg and 80-Mg Tablets: A Randomized,Open-Label, 4-Way Crossover Study in Healthy Chinese Male Volunteers

The present study aimed to investigate the pharmacokinetic properties of febuxostat in healthy Chinese male volunteers and evaluate whether the two formulations of febuxostat 40-mg and 80-mg tablets are bioequivalent. A randomized, open-label, 4-way crossover study was conducted in healthy Chinese male volunteers under fasting conditions. 24 eligible subjects were randomized in a 1:1:1:1 ratio to receive a single dose of test or reference formulation of febuxostat 40-mg or 80-mg tablet. The washout period between each administration was 1 week. Plasma febuxostat was quantified by a validated liquid chromatography-tandem mass spectrometry (LC-MS/MS) method. Tolerability was evaluated by monitoring adverse events, physical examinations, 12-lead ECG and laboratory tests. After single-dosing of 1 tablet of 40-mg febuxostat, the pharmacokinetic parameters of test and reference formulations were: T_max 1.22±0.87 and 1.85±1.03 h, C_max 1689.16±461.31 and 1613.80±608.43 ng·mL^-1, AUC_0-t 5139.87±1349.28 and 5517.91±2024.26 ng·mL^-1·h, AUC_0−∞ 5263.06±1339.16 and 5640.48±2040.22 ng·mL^-1·h, t_1/2 4.82±2.61 and 4.85±1.78 h, respectively. After single-dosing of 1 tablet of 80-mg febuxostat, the pharmacokinetic parameters of test and reference formulations were: T_max 1.71±1.21 and 2.23±1.55 h, C_max 2744.47±1157.44 and 2998.17±1200.13 ng·mL^-1, AUC_0-t 9634.03±2768.25 and 10467.95±3501.65 ng·mL^-1·h, AUC_0−∞ 9834.32±2730.51 and 10626.63±3504.08 ng·mL^-1·h, t_1/2 6.25±2.44 and 5.46±1.65 h, respectively. For single-dosing of 1 tablet of 40-mg febuxostat, 90% CIs for the test/reference ratio of AUC_0-t, AUC_0−∞ and C_max were 89.79 to 102.55, 90.14 to 102.56 and 93.99 to 129.63, respectively. For single-dosing of 1 tablet of 80-mg febuxostat, 90% CIs for the test/reference ratio of AUC_0-t, AUC_0−∞ and C_max were 86.67 to 100.00, 87.50 to 100.51 and 79.48 to 105.99, respectively. This single dose study revealed similar pharmacokinetic properties in healthy Chinese male volunteers as those found in Caucasic population. The test and reference febuxostat tablets formulations met the regulatory criteria for bioequivalence at 40-mg and 80-mg strengths in fasting healthy Chinese male volunteers.Trial Registration: Chictr.org ChiCTR-TTRCC-14004288     

CO2-induced ion and fluid transport in human retinal pigment epithelium

In the intact eye, the transition from light to dark alters pH, [Ca²⁺], and [K] in the subretinal space (SRS) separating the photoreceptor outer segments and the apical membrane of the retinal pigment epithelium (RPE). In addition to these changes, oxygen consumption in the retina increases with a concomitant release of CO₂ and H₂O into the SRS. The RPE maintains SRS pH and volume homeostasis by transporting these metabolic byproducts to the choroidal blood supply. In vitro, we mimicked the transition from light to dark by increasing apical bath CO₂ from 5 to 13%; this maneuver decreased cell pH from 7.37 ± 0.05 to 7.14 ± 0.06 (n = 13). Our analysis of native and cultured fetal human RPE shows that the apical membrane is significantly more permeable (≈10-fold; n = 7) to CO₂ than the basolateral membrane, perhaps due to its larger exposed surface area. The limited CO₂ diffusion at the basolateral membrane promotes carbonic anhydrase–mediated HCO₃ transport by a basolateral membrane Na/nHCO₃ cotransporter. The activity of this transporter was increased by elevating apical bath CO₂ and was reduced by dorzolamide. Increasing apical bath CO₂ also increased intracellular Na from 15.7 ± 3.3 to 24.0 ± 5.3 mM (n = 6; P < 0.05) by increasing apical membrane Na uptake. The CO₂-induced acidification also inhibited the basolateral membrane Cl/HCO₃ exchanger and increased net steady-state fluid absorption from 2.8 ± 1.6 to 6.7 ± 2.3 µl × cm⁻² × hr⁻¹ (n = 5; P < 0.05). The present experiments show how the RPE can accommodate the increased retinal production of CO₂ and H₂O in the dark, thus preventing acidosis in the SRS. This homeostatic process would preserve the close anatomical relationship between photoreceptor outer segments and RPE in the dark and light, thus protecting the health of the photoreceptors.     

Temperature Characteristics of Excitation in Space-Clamped Squid Axons

Temperature characteristics of excitability in the squid giant axon were measured for the space-clamped axon with the double sucrose gap technique. Threshold strength-duration curves were obtained for square wave current pulses from 10 µsec to 10 msec and at temperatures from 5°C to 35°C. The threshold change of potential, at which an action potential separated from a subthreshold response, averaged 17 mv at 20°C with a Q¹⁰ of 1.15. The average threshold current density at rheobase was 12 µa/cm² at 20°C with a Q¹⁰ of 2.35 compared to 2.3 obtained previously. At short times the threshold charge was 1.5·10^-8 coul/cm². This was relatively independent of temperature and occasionally showed a minimum in the temperature range. At intermediate times and all temperatures the threshold currents were less than for both the single time constant model and the two factor excitation process as developed by Hill. FitzHugh has made computer investigations of the effect of temperature on the excitation of the squid axon membrane as represented by the Hodgkin-Huxley equations. These are in general in good agreement with our experimental results.     

Relationships among Mercury Concentration,and Stable Isotope Ratios of Carbon and Nitrogen in the Scalp Hair of Residents from Seven Countries: Effects of Marine Fish and C4 Plants Consumption

We analyzed the Hg concentration, and δ¹³C and δ¹⁵N values in the scalp hair of residents from seven countries; Vietnam, New Zealand, Spain, the USA, South Korea, Brazil and Japan. Relationships among the data in each country and among the seven countries were then examined. The highest Hg concentration as well as the highest or higher δ¹⁵N value in each country was found in the hair of a heavy marine fish-eater, whereas the lowest Hg concentration and δ¹⁵N value were found in the hair of a vegetarian or non (marginal)-fish eater. Hg concentrations were positively correlated with the δ¹⁵N values in each country, and increased markedly in samples with δ¹⁵N values exceeding 9.0 ‰, probably due to fish consumption. The highest Hg concentration could be found in sample, with a δ¹³C value between -19 and -18‰, probably reflecting the δ¹³C value of the marine food web.