Preparation of chitin nanofibers from squid pen beta-chitin by simple mechanical treatment under acid conditions

A procedure for preparing individualized chitin nanofibers 3-4 nm in cross-sectional width and at least a few microns in length was developed. The key factors to prepare the chitin nanofibers with such high aspect ratios are as follows: (1) squid pen beta-chitin is used as the starting material and (2) ultrasonication of the beta-chitin in water at pH 3-4 and 0.1-0.3% consistency for a few minutes. Transparent and highly viscous dispersions of squid pen beta-chitin nanofibers in water can be obtained by this method. No N-deacetylation occurs on the chitin molecules during the nanofiber conversion procedure. Moreover, the original crystal structure of beta-chitin is maintained, although crystallinity index decreases from 0.51 to 0.37 as a result of the nanofiber conversion. Cationization of the C2 amino groups present on the crystallite surfaces of the squid pen beta-chitin under acid conditions is necessary for preparing the nanofibers.     

Crystallization of calcium carbonate salts into beta-chitin scaffold

Composites of beta-chitin with calcium carbonate polymorphs were prepared by precipitation of the mineral into a chitin scaffold by means of a double diffusion system. The beta-chitin was obtained from the pen of the Loligo sp. squid. The three main polymorphs of calcium carbonate: aragonite, calcite and vaterite, were observed. Their location within the matrix is a function of the polymorph. The supersaturation inside the compartmentalized space in the chitin governs the location and polymorphism of the crystals.     

Two-dimensional magic angle spinning NMR investigation of naturally occurring chitins: precise 1H and 13C resonance assignment of alpha- and beta-chitin

13C homonuclear through-bond correlations of alpha- and beta-chitin were determined by using two-dimensional (2D) INADEQUATE spectra of these allomorphs purified from crab shell and squid pen, respectively. The 2D (13)C-(13)C correlation spectra where two directly bonded carbons share a common double-quantum frequency (DQ) enabled us to precisely assign all (13)C resonances of the chitin allomorphs for the first time. Following the complete (13)C assignment, (1)H chemical shifts of protons attached to each carbon nuclei were assigned by 2D frequency-switched Lee-Goldberg (FSLG) (1)H-(13)C heteronuclear correlation (HETCOR) spectra of the chitin allomorphs, recorded with a short mixing time (60 micros) to provide isotropic (1)H-(13)C chemical shift correlations between bonded pairs proton and carbon nuclei. From the (13)C and (1)H chemical shifts of chitin allomorphs, all 2-deoxy-2-acetamide-D-glucose (N-acetyl-D-glucosamine) monomer units in each allomorph were revealed to be an identical (13)C-(13)C backbone conformation and magnetically equivalent. In addition, it was strongly suggested that there are two different hydrogen-bonding patterns at the hydroxyl groups of alpha-chitin by comparing (1)H chemical shifts at the C6 site of alpha-chitin with those at the same site of beta-chitin.     

Beta-chitin from the pens of Loligo sp.: extraction and characterization

Recently the squid pens, a rich source of beta-chitin containing low contents of inorganic compounds, have become available in considerable amounts as a refuse of the fishery industries in Brazil. Thus, the aim of this work is to use squid pens from Loligo sanpaulensis and Loligo plei, species found in the Brazilian coast, as the raw material for the extraction of beta-chitin. The squid pens were submitted to the usual sequence of treatments used for chitin extraction - demineralization and deproteinization - but due to its low content of inorganic compounds a two-step alkaline treatment was enough to produce beta-chitin with low contents of ash (< or = 0.7%). Indeed, the low contents of ash and metals, such as Ca (< or = 10.4 ppm), Mg (< or = 2.5 ppm), Mn (< or = 3.1 ppm) and Fe (< or = 1.8 ppm), are lower than those reported in most of the papers found in the literature. Also, the beta-chitin extracted by employing only the alkaline treatment was more acetylated than the other samples prepared in this work. Regardless of the treatment employed for the extraction of the beta-chitin from the squid pens, its infrared spectra and X-ray diffraction pattern presented only minor differences, however they were clearly distinguished from commercial alpha-chitin.     

Utilization of commercial non-chitinase enzymes from fungi for preparation of 2-acetamido-2-deoxy-D-glucose from beta-chitin

Commercial non-chitinase enzymes from Aspergilus niger, Acremonium cellulolyticus and Trichoderma viride were investigated for potential utilization in the preparation of 2-acetamido-2-deoxy-D-glucose (N-acetyl-D-glucosamine, GlcNAc) from chitin. Among the tested enzymes, cellulase A. cellulolyticus exhibited highest chitinolytic activity per weight toward amorphous chitin and beta-chitin from squid pen. The optimum pH of the enzyme was 3 where it produced two major hydrolytic products, GlcNAc and N,N'-diacetylchitobiose ([GlcNAc](2)). The product ratio, GlcNAc:[GlcNAc](2), increased while the total yield decreased as the pH was raised from 3. All of the [GlcNAc](2) produced at pH 3 can be converted in situ to GlcNAc by mixing cellulase A. cellulolyticus with one of several other enzymes from A. niger resulting in a higher yield of GlcNAc. An appropriate mixing ratio of cellulase A. cellulolyticus to another enzyme was 9:1 (w/w) and an optimum substrate concentration was 20 mg/mL.     

Preparation and characterization of novel beta-chitin-hydroxyapatite composite membranes for tissue engineering applications

Beta-chitin is a biopolymer principally found in shells of squid pen. It has the properties of biodegradability, biocompatibility, chemical inertness, wound healing, antibacterial and anti-inflammatory activities. Hydroxyapatite (HAp) is a natural inorganic component of bone and teeth and has osteoconductive property. In this work, beta-chitin-HAp composite membranes were prepared by alternate soaking of beta-chitin membranes in CaCl2 (pH 7.4) and Na2HPO4 solutions for 2 h in each solution. After 1, 3 and 5 cycles of immersion, beta-chitin membranes were characterized using the SEM, FT-IR, EDS and XRD analyses. The results showed the presence of apatite layer on surface of beta-chitin membranes, and the amounts of size and deposition of apatite layers were increased with increasing number of immersion cycles. Human mesenchymal stem cells (hMSCs) were used for evaluation of the biocompatibility of pristine as well as composite membranes for tissue engineering applications. The presence of apatite layers on the surface of beta-chitin membranes increased the cell attachment and spreading suggesting that beta-chitin-HAp composite membranes can be used for tissue engineering applications.     

Esterification of beta-chitin via intercalation by carboxylic anhydrides

beta-chitin is known to form intercalation complexes with aliphatic alcohols and amines. We found that it also forms complexes with carboxylic anhydrides. When the beta-chitin-acetic anhydride complex was heated to 105 degrees C, the hydroxyl groups of chitin were acetylated by a host-guest reaction, maintaining the host's crystal structure. Structures of complex and acetylated products were analyzed by X-ray diffraction, (13)C CP/MAS NMR, and infrared spectroscopy. The maximum degree of substitution (DS) was close to 1.0, suggesting regioselective esterification at the C6 position of chitin. Partially acetylated beta-chitin with a DS of 0.4 could incorporate various guest species that are difficult to be incorporated by original beta-chitin. In contrast, beta-chitin acetate with a DS of 1 lost the ability to form a complex. Intercalation complexes of beta-chitin with cyclic anhydrides (succinic and maleic) also underwent esterification by heating, and the products with a DS of approximately 1 dissolved in aqueous alkali, apparently as the result of the dissociation of introduced carboxyl groups. These phenomena are potentially useful in controlling the complexation ability of beta-chitin and the preparation of regioselectively esterified chitin derivatives.     

Chitosan functional properties

Chitosan is a partially deacetylated polymer of N-acetyl glucosamine. It is essentially a natural, water-soluble, derivative of cellulose with unique properties. Chitosan is usually prepared from chitin (2 acetamido-2-deoxy β-1,4-D-glucan) and chitin has been found in a wide range of natural sources (crustaceans, fungi, insects, annelids, molluscs, coelenterata etc.) However chitosan is only manufactured from crustaceans (crab and crayfish) primarily because a large amount of the crustacean exoskeleton is available as a by product of food processing. Squid pens (a waste byproduct of New Zealand squid processing) are a novel, renewable source of chitin and chitosan. Squid pens are currently regarded as waste and so the raw material is relatively cheap. This study was intended to assess the functional properties of squid pen chitosan. Chitosan was extracted from squid pens and assessed for composition, rheology, flocculation, film formation and antimicrobial properties. Crustacean chitosans were also assessed for comparison. Squid chitosan was colourless, had a low ash content and had significantly improved thickening and suspending properties. The flocculation capacity of squid chitosan was low in comparison with the crustacean sourced chitosans. However it should be possible to increase the flocculation capacity of squid pen chitosan by decreasing the degree of acetylation. Films made with squid chitosan were more elastic than crustacean chitosan with improved functional properties. This high quality chitosan could prove particularly suitable for medical/analytical applications. This revised version was published online in November 2006 with corrections to the Cover Date.     

Self-assembly and mineralization of genetically modifiable biological nanofibers driven by β-structure formation

Bioinspired mineralization is an innovative approach to the fabrication of bone biomaterials mimicking the natural bone. Bone mineral hydroxylapatite (HAP) is preferentially oriented with c-axis parallel to collagen fibers in natural bone. However, such orientation control is not easy to achieve in artificial bone biomaterials. To overcome the lack of such orientation control, we fabricated a phage-HAP composite by genetically engineering M13 phage, a nontoxic bionanofiber, with two HAP-nucleating peptides derived from one of the noncollagenous proteins, Dentin Matrix Protein-1 (DMP1). The phage is a biological nanofiber that can be mass produced by infecting bacteria and is nontoxic to human beings. The resultant HAP-nucleating phages are able to self-assemble into bundles by forming β-structure between the peptides displayed on their side walls. The β-structure further promotes the oriented nucleation and growth of HAP crystals within the nanofibrous phage bundles with their c-axis preferentially parallel to the bundles. We proposed that the preferred orientation resulted from the stereochemical matching between the negatively charged amino acid residues within the β-structure and the positively charged calcium ions on the (001) plane of HAP crystals. The self-assembly and mineralization driven by the β-structure formation represent a new route for fabricating mineralized fibers that can serve as building blocks in forming bone repair biomaterials and mimic the basic structure of natural bones.     

Structural data on the intra-crystalline swelling of beta-chitin

The intra-crystalline swelling of the highly crystalline beta-chitin from Tevnia jerichonana was investigated by X-ray crystallography and Fourier transform infrared (FTIR) spectroscopy, using hydrogenated and deuterated hydrochloric acids as swelling agents. Three levels of swelling were identified that could be defined as inter- and intra-sheet swelling. A moderate and reversible swelling in water and methanol gave crystalline beta-chitin cystallosolvates, namely dihydrate and methanolate, respectively. In these, an inter-sheet swelling was observed, corresponding to an expansion of only the b parameter of the unit cell of beta-chitin. Under these swelling conditions, the use of deuterated reagents had no effect on the amide N&z.sbnd;H⋯O&z.dbnd6;C hydrogen bonds that hold the structure of beta-chitin together, but only induced a partial and reversible deuteration of the chitin hydroxymethyl groups. A more severe swelling - but still reversible - occurred with 6 N HCl or DCl, which converted the crystals of beta-chitin into a paracrystalline gel-like product resulting from inter-sheet+intra-sheet swelling. With this acid strength, the deuteration pattern indicated that a fraction of the amide hydrogen bonds was broken and became susceptible to an irreversible deuteration. A very severe and irreversible swelling occurred with 8 N HCl or DCl. In that case, the inter- and intra-sheet swelling was extensive to the point where all memory of the parallel-chain beta-chitin was lost. In addition, this swelling was accompanied by a drastic and rapid depolymerization. The treatment with 8 N HCl led invariably to crystalline alpha-chitin when the samples were neutralized.     

Reclamation of chitinous materials by bromelain for the preparation of antitumor and antifungal materials

The main purpose of this research was to investigate the antitumor and antimicrobial activities of the chitooligosaccharides containing hydrolyzates obtained from the hydrolysis of chitinous materials (such as chitin, chitosan, and squid pen) by bromelain. The optimum preparations were gained in the hydrolysates of squid pen powder hydrolyzed at pH 5, 37 degrees C for 2 days by 0.1% bromelain. The hydrolysates had an 80% inhibitory activity on phyto-pathogenic mold Fusarium oxysporum. Chitooligosaccharides were recovered from the hydrolysates and were used for tumor cell surviving test. Surviving rate of the human leukemic U937 cells was reduced to 69% by the chitooligosaccharides. The solution of 0.1% of water-soluble chitosan was also hydrolyzed for 1 day at pH 5, 37 degrees C by bromelain. The resultant hydrolysates contained the highest chitooligosaccharides, which had inhibitory effect on Bacillus subtilis and also had 40% inhibitory activity on human pathogenic mold Aspergillus fumigatus. Surviving rate of mouse CT26 colorectal adenocarcinoma cells was reduced to 57% by the chitooligosaccharides. This is the first publication of enzymatic reclamation of squid pen (fishery processing waste) for the preparation of antitumor and antimicrobial materials.     

Orientation of bone mineral and its role in the anisotropic mechanical properties of bone--transverse anisotropy

An orientation of hydroxyapatite (HAP) crystals in bovine femur mineral was investigated by means of X-ray pole figure analysis (XPFA). It was found that the c-axis of HAP generally orients parallel to the longitudinal axis of bone (bone axis) and a significant amount of c-axis was oriented in other directions, in particular, perpendicular to the bone axis. Comparing these results with those of the small angle X-ray scattering (SAXS) investigation by Matsushima et al. (Jap. J. appl. Phys. 21, 186-189, 1982) at least two types of morphology of bone mineral were found; rod like bone mineral having the c-axis of HAP crystal parallel to the longitudinal axis of the rod and that having the c-axis not parallel, in a particular case, perpendicular to its longitudinal axis. Transverse anisotropy in mechanical properties of bone was reproduced by the estimation of Young's moduli by using the structural results mainly from XPFA. It is concluded that the anisotropy in mechanical properties of bone is well explained by taking account of the non-longitudinal (off-bone) axial distribution of orientation of bone mineral.     

Roles of the exposed aromatic residues in crystalline chitin hydrolysis by chitinase A from Serratia marcescens 2170

Four exposed aromatic residues, two in the N-terminal domain (Trp-69 and Trp-33) and two in the catalytic domain (Trp-245 and Phe-232) of Serratia marcescens chitinase A, are linearly aligned with the deep catalytic cleft. To investigate the importance of these residues in the binding activity and hydrolyzing activity against insoluble chitin, site-directed mutagenesis to alanine was carried out. The substitution of Trp-69, Trp-33, or Trp-245 significantly reduced the binding activity to both highly crystalline beta-chitin and colloidal chitin. The substitution of Phe-232, which is located closest to the catalytic cleft, did not affect the binding activity. On the other hand, the hydrolyzing activity against beta-chitin microfibrils was significantly reduced by the substitution of any one of the four aromatic residues including Phe-232. None of the mutations reduced the hydrolyzing activity against soluble substrates. These results clearly demonstrate that the four exposed aromatic residues are essential determinants for crystalline chitin hydrolysis. Three of them, two in the N-terminal domain and one in the catalytic domain, play vital roles in the chitin binding. Phe-232 appeared to be important for guiding the chitin chain into the catalytic cleft. Based on these observations, a model for processive hydrolysis of crystalline chitin by chitinase A is proposed.     

Expression and characterization of the chitin-binding domain of chitinase A1 from Bacillus circulans WL-12

Chitinase A1 from Bacillus circulans WL-12 comprises an N-terminal catalytic domain, two fibronectin type III-like domains, and a C-terminal chitin-binding domain (ChBD). In order to study the biochemical properties and structure of the ChBD, ChBD(ChiA1) was produced in Escherichia coli using a pET expression system and purified by chitin affinity column chromatography. Purified ChBD(ChiA1) specifically bound to various forms of insoluble chitin but not to other polysaccharides, including chitosan, cellulose, and starch. Interaction of soluble chitinous substrates with ChBD(ChiA1) was not detected by means of nuclear magnetic resonance and isothermal titration calorimetry. In addition, the presence of soluble substrates did not interfere with the binding of ChBD(ChiA1) to regenerated chitin. These observations suggest that ChBD(ChiA1) recognizes a structure which is present in insoluble or crystalline chitin but not in chito-oligosaccharides or in soluble derivatives of chitin. ChBD(ChiA1) exhibited binding activity over a wide range of pHs, and the binding activity was enhanced at pHs near its pI and by the presence of NaCl, suggesting that the binding of ChBD(ChiA1) is mediated mainly by hydrophobic interactions. Hydrolysis of beta-chitin microcrystals by intact chitinase A1 and by a deletion derivative lacking the ChBD suggested that the ChBD is not absolutely required for hydrolysis of beta-chitin microcrystals but greatly enhances the efficiency of degradation.     

Inclusion complex of beta-chitin and aliphatic amines

Inclusion complexation of beta-chitin with linear aliphatic amines was studied by X-ray diffraction. All tested amines, C3 to C8 monoamines and C2 to C7 diamines with terminal amino groups, reversibly formed crystalline complexes with beta-chitin by immersion of dry chitin in pure liquid. Complex formation caused linear increase in the 010 sheet spacing of beta-chitin depending on the carbon number of amine. The complexes could be classified as type I and type II according to the increment of sheet spacing against carbon number. All monoamines formed type II complexes. In dry conditions, diamine formed a type I complex though the type of diamine complex differed for guest species in wet conditions. Based on the unit cell dimension and thermogravimetry, type II and type I are likely to correspond to guest-host (amine-chitobiose) ratios of 2:1 and 1:1, respectively. These differences seem to arise from varied interactions between functional groups of chitin and amines.     

Fast intracrystalline hydration of beta-chitin revealed by combined microdrop generation and on-line synchrotron radiation microdiffraction

Water microdrops of about 50 microm in diameter, generated by an ink-jet system, have been used to hydrate fragments of Pogonophora tubes. In situ X-ray microdiffraction with a beam size of 10 microm was used to follow the structural transformations that affected the crystalline beta-chitin part of the specimens. Starting from anhydrous chitin, the formation of a full beta-chitin dihydrate was observed within about 90 s. A disordered intermediate phase with variable d-spacing that could be due to a mixture of anhydrous and hydrated beta-chitin layers was also detected.     

Chitin Degradation Proteins Produced by the Marine Bacterium Vibrio harveyi Growing on Different Forms of Chitin

Relatively little is known about the number, diversity, and function of chitinases produced by bacteria, even though chitin is one of the most abundant polymers in nature. Because of the importance of chitin, especially in marine environments, we examined chitin-degrading proteins in the marine bacterium Vibrio harveyi. This bacterium had a higher growth rate and more chitinase activity when grown on (beta)-chitin (isolated from squid pen) than on (alpha)-chitin (isolated from snow crab), probably because of the more open structure of (beta)-chitin. When exposed to different types of chitin, V. harveyi excreted several chitin-degrading proteins into the culture media. Some chitinases were present with all of the tested chitins, while others were unique to a particular chitin. We cloned and identified six separate chitinase genes from V. harveyi. These chitinases appear to be unique based on DNA restriction patterns, immunological data, and enzyme activity. This marine bacterium and probably others appear to synthesize separate chitinases for efficient utilization of different forms of chitin and chitin by-products.     

Thermally reversible hydration of beta-chitin

Thermally induced transition between anhydrous and hydrated forms of highly crystalline beta-chitin was studied by differential thermal calorimetry (DSC) and X-ray diffraction. DSC of wet beta-chitin in a sealed pan gave two well-defined endothermic peaks at 85.2 and 104.7 degrees C on heating and one broad exothermic peak at between 60 and 0 degrees C on cooling. These peaks were highly reproducible and became more distinct after repeated heating-cooling cycles. The X-ray diffraction pattern of wet beta-chitin at elevated temperature showed corresponding changes in d-spacing between the sheets formed by stacking of chitin molecules. These phenomena clearly show that water is reversibly incorporated into the beta-chitin crystal and that the temperature change induces transitions between anhydrous, monohydrate, and dihydrate forms. The DSC behavior in heating-cooling cycles, including reversion between the two endothermic peaks, indicated that the transition between monohydrate and dihydrate was a fast and narrow-temperature process, whereas the one between the anhydrous and the monohydrate form was a slow and wide-temperature process.     

Trp122 and Trp134 on the surface of the catalytic domain are essential for crystalline chitin hydrolysis by Bacillus circulans chitinase A1

From the 3D-structural analysis of the catalytic domain of chitinase A1, two exposed tryptophan residues (W122 and W134) are proposed to play an important role in guiding a chitin chain into the catalytic cleft during the crystalline chitin hydrolysis. Mutation of either W122 or W134 to alanine significantly reduced the hydrolyzing activity against highly crystalline beta-chitin microfibrils. Double mutation almost completely abolished the hydrolyzing activity. On the other hand, the hydrolyzing activity against either soluble or amorphous substrate was not reduced. These mutations slightly impaired the binding activity of this enzyme. These results clearly demonstrated that the two exposed aromatic residues play a critical role in hydrolyzing the chitin chain in crystalline chitin.     

TEMPO-mediated oxidation of β-chitin to prepare individual nanofibrils

TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical)-mediated oxidation was applied to β-chitins, originating from tubeworm and squid pen, to prepare chitin nanofibrils. Water-insoluble fractions of the TEMPO-oxidized β-chitins were obtained in various ratios by controlling the addition level of NaClO used as the primary oxidant in the oxidation. The water-insoluble fractions of the TEMPO-oxidized tubeworm β-chitins, when they had carboxylate groups of 0.18–0.25 mmol/g, were successfully converted to highly viscous and translucent gels by disintegration in water. The gels consisted of mostly individual nanofibrils 20–50 nm in width and at least several microns in length. On the other hand, the water-insoluble fractions of the TEMPO-oxidized squid pen β-chitins could be transformed to neither transparent nor translucent dispersions under any oxidation or disintegration conditions used. When sufficient amounts of NaClO were used, both β-chitins were completely oxidized to the corresponding water-soluble polyuronic acids by oxidation of all C6 primary hydroxyls to carboxylate groups.