Glucose sensor for flow injection analysis of serum glucose based on immobilization of glucose oxidase in titania sol-gel membrane

A novel amperometric glucose sensor was constructed by immobilizing glucose oxidase (GOD) in a titania sol-gel film, which was prepared with a vapor deposition method. The sol-gel film was uniform, porous and showed a very low mass transport barrier and a regular dense distribution of GOD. Titania sol-gel matrix retained the native structure and activity of entrapped enzyme and prevented the cracking of conventional sol-gel glasses and the leaking of enzyme out of the film. With ferrocenium as a mediator the glucose sensor exhibited a fast response, a wide linear range from 0.07 to 15 mM. It showed a good accuracy and high sensitivity as 7.2 microA cm(-2) mM(-1). The general interferences coexisted in blood except ascorbic acid did not affect glucose determination, and coating Nafion film on the sol-gel film could eliminate the interference from ascorbic acid. The serum glucose determination results obtained with a flow injection analysis (FIA) system showed an acceptable accuracy, a good reproducibility and stability and indicated the sensor could be used in FIA determination of glucose. The vapor deposition method could fabricate glucose sensor in batches with a very small amount of enzyme.     

Changes in phenol oxidation rate of a mixed microbial culture caused by sol-gel immobilization

A mixed microbial culture was entrapped into porous silica gel prepared by two different sol-gel methods. The immobilization of cells into prepolymerized tetraethoxysilane was more stressful to living microbial cells than the entrapment into colloidal SiO₂. Our experimental equipment operating in a sensor mode was able to detect 0.5 mg phenol l^–1 and had a linear response in the range from 2 to 10 mg phenol l^–1.     

Glutamate optical biosensor based on the immobilization of glutamate dehydrogenase in titanium dioxide sol-gel matrix

A simple and novel titania sol-gel derived optical biosensor coupled with carboxy seminaphthorhodamine-1-dextran (SNARF-1-dextran) as the fluorescent dye was fabricated for the determination of glutamate in water and biological samples. The NADH-dependent glutamate dehydrogenase (GLDH) was trapped in titania sol-gel derived matrix prepared by vapor deposition method. In addition, scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to characterize the surface morphology of the spots. SEM and AFM images showed that the deposition of titania precursor at 27 degrees C for 6.5h was found to be suitable to form transparent titania sol-gel matrix to encapsulate GLDH and fluorescent probe. AFM images showed that the roughness of TiO(2) surface increased from 2.16 nm in the absence of GLDH and SNARF to 37.8 nm after the immobilization. The developed titania biosensor has good analytical performance with water samples. A dynamic range between 0.04 and 10mM with the detection limit of 5.5 microM were observed. The responses to glutamate in biological samples also showed good performances, and the dynamic range and detection limit were 0.02-10mM and 6.7 microM, respectively. High precision with relative standard deviations of 4.2 and 10.7% in water and biological samples, respectively, were also demonstrated. In addition, the biosensor showed a relatively high storage stability over more than 1 month. Results obtained in this study clearly demonstrate that this simple vapor deposition method can be successfully used to form transparent titania sol-gel film for the fabrication of glutamate biosensors that are suitable for optical detection of glutamate in water and biological samples.     

Immobilization of laccase by encapsulation in a sol-gel matrix and its characterization and use for the removal of estrogens

Laccase from Myceliophthora thermophila was immobilized by encapsulation in a sol-gel matrix based on methyltrimethoxysilane and tetramethoxysilane. The amount of laccase used for the preparation of the hydrogel was in the range 2.2-22 mg of protein/mL sol and the corresponding enzymatic activities were in the range 5.5-17.0 U/g biocatalyst. The kinetic parameters of the encapsulated laccase showed that the immobilized enzyme presented lower affinity for the substrate 2,2'-azinobis-(3-ethylbenzothiazoline-6-sulfonate) (ABTS). However, the stability of laccase was significantly enhanced after immobilization; thus, both pH and thermal stability improved about 10-30% and tolerance to different inactivating agents (NaN(3) , ZnCl(2) , CoCl(2) , CaCl(2) , methanol, and acetone) was 20-40% higher. The reusability of the immobilized laccase was demonstrated in the oxidation of ABTS for several consecutive cycles, preserving 80% of the initial laccase activity after 10 cycles. The feasibility of the immobilized biocatalyst was tested for the continuous elimination of Acid Green 27 dye as a model compound in a packed-bed reactor (PBR). Removals of 70, 58, 57, and 55% were achieved after four consecutive cycles with limited adsorption on the support: only 10-15%. Finally, both batch stirred tank reactor (BSTR) operated in several cycles and PBR, containing the solid biocatalyst were applied for the treatment of a solution containing the endocrine disrupting chemicals (EDCs): estrone (E1), 17β-estradiol (E2), and 17α-ethinylestradiol (EE2). Eliminations of EDCs in the BSTR were higher than 85% and the reusability of the biocatalyst for the degradation of those estrogens was demonstrated. In the continuous operation of the PBR, E1 was degraded by 55% and E2 and EE2 were removed up to 75 and 60%, at steady-state conditions. In addition, a 63% decrease in estrogenic activity was detected.     

Optical oxygen sensor based on metallo-organic compound immobilized by sol-gel technique

Summary Optical sensors suitable for monitoring of O₂ in water medium were prepared by immobilization of metallo-organic complexes in xerogels created by sol-gel technique and applied to optical fibre tip or glass slides by dipping. Tris (1,10-phenanthroline)ruthenium (II) chloride was immobilized on the tip of optical fibre. The fluorescence spectra of the complex were sensitive to O₂ in water solution. The sensitivity of absorption spectra of bis(histidinato)cobalt (II) to O₂ and pH was examinated both in the solution of precursors of silica sol-gel glasses and in the complex-containing coating of glass slides.     

Hydrodynamic deposition: a novel method of cell immobilization.

A novel method of cell immobilization is described. The cell support consists of ceramic microspheres of approximately 50-75 microns diameter. The spheres are hollow, having a wall thickness of 10-15 microns and one entrance (ca. 20 microns diameter). The walls are porous with a mean pore size of approximately 90 nm. When a cell suspension (of S. cerevisiae) is passed through a column of such particles, cells are immobilized. Conditions are devised such that the overwhelming majority of cells are held in the central cavity of the support and not between the particles. Provided turbulence is avoided, the distribution of cells along the column length in the steady state is rather homogeneous. The facts that (a) essentially all particles, regardless of orientation, entrap cells, and (b) nonporous particles also entrap cells with high efficiency, indicate that filtration effects are irrelevant and that heretofore unrecognized hydrodynamic forces are alone responsible for the cell immobilization. Cells can be immobilized to high biomass densities, while the hydrodynamic properties of columns containing such immobilized cells are excellent. We describe an on-line electronic method for the real-time measurement of immobilized cellular biomass. Cell growth (so recorded) and metabolism continue to occur in such particles at high rates. Using the glycolytic production of ethanol by S. cerevisiae as a model reaction, volumetric productivities as great as any published are obtained. Thus the "lobster-pot effect" or "hydrodynamic deposition" represents a novel, promising, and generally applicable method of cell immobilization.     

Silica sol-gel composite film as an encapsulation matrix for the construction of an amperometric tyrosinase-based biosensor

An amperometric tyrosinase enzyme electrode for the determination of phenols was developed by a simple and effective immobilization method using sol-gel techniques. A grafting copolymer was introduced into sol-gel solution and the composition of the resultant organic-inorganic composite material was optimized, the tyrosinase retained its activity in the sol-gel thin film and its response to several phenol compounds was determined at 0 mV vs. Ag/AgCl (sat. KCl). The dependences of the current response on pH, oxygen level and temperature were studied, and the stability of the biosensor was also evaluated. The sensitivity of the biosensor for catechol, phenol and p-cresol was 59.6, 23.1 and 39.4 microA/mM, respectively. The enzyme electrode maintained 73% of its original activity after intermittent use for three weeks when storing in a dry state at 4 degrees C.     

Nanosized flower-like ZnO synthesized by a simple hydrothermal method and applied as matrix for horseradish peroxidase immobilization for electro-biosensing

Nanosized flower-like ZnO was synthesized by a simple hydrothermal method which is a convenient, environment friendly, inexpensive and efficient process. Raman spectroscopy, X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to confirm the material structure and the crystallite microstructure. Then ZnO was dispersed in the chitosan solution to form a ZnO/chitosan composite matrix for the fabrication of H2O2 biosensor. This composite combined the advantages of inorganic species (ZnO) and organic polymer (chitosan). The parameters affecting the fabrication and experimental conditions of biosensors were optimized. Using hydroquinone as the mediator, the biosensor showed a fast response of less than 5s with the linear range of 1.0x10(-5) to 1.8x10(-3) M H2O2 with a correlation coefficient of 0.995 (n=20). The detection limit of the sensor was found to be 2.0 microM, based on a signal-to-noise ratio of 3. The biosensor exhibited satisfactory reproducibility and stability and retained about 78% of its original response after 40 days storage in a phosphate buffer at 4 degrees C.     

Curdlan as a support matrix for immobilization of enzyme

Curdlan, a high molecular weight extracellular β(1→3) glucan produced by pure culture fermentation by Agrobacterium radiobacter NCIM 2443 contains large number of free hydroxyl groups. The reaction of hydroxyl containing supports with epichlorohydrin results in activated epoxy groups that can covalently link with available amino, hydroxyl, or sulfhydryl groups of enzymes, thereby immobilizing it. The present work reports on preparation of epoxy-activated matrix for immobilization of a model enzyme, porcine pancreatic lipase. The binding capacity of the matrix prepared by extraction of epoxy-activated curdlan by isopropyl alcohol was found to be 58.7% with about 0.6% loss of the enzyme activity during immobilization. Further, the specific activity of the enzyme increased marginally from 9.37 to 10.2. The corresponding value was 10.15 for a commercial sample of curdlan, epoxy-activated as for laboratory-isolated curdlan. Sepharose, the most widely used support matrix for the immobilization of enzymes was used for comparison in this study.     

Development of amperometric biosensor for glucose based on a novel attractive enzyme immobilization matrix: calcium carbonate nanoparticles

Calcium carbonate nanoparticles (nano-CaCO3) may be a promising material for enzyme immobilization owing to their high biocompatibility, large specific surface area and their aggregation properties. This attractive material was exploited for the mild immobilization of glucose oxidase (GOD) in order to develop glucose amperometric biosensor. The GOD/nano-CaCO3-based sensor exhibited a marked improvement in thermal stability compared to other glucose biosensors based on inorganic host matrixes. Amperometric detection of glucose was evaluated by holding the modified electrode at 0.60 V (versus SCE) in order to oxidize the hydrogen peroxide generated by the enzymatic reaction. The biosensor exhibited a rapid response (6s), a low detection limit (0.1 microM), a wide linear range of 0.001-12 mM, a high sensitivity (58.1 mAcm-2M-1), as well as a good operational and storage stability. In addition, optimization of the biosensor construction, the effects of the applied potential as well as common interfering compounds on the amperometric response of the sensor were investigated and discussed herein.     

Third-generation superoxide anion sensor based on superoxide dismutase directly immobilized by sol-gel thin film on gold electrode

A third-generation biosensor for superoxide anion (O(2)*-) was developed based on superoxide dismutase (SOD) immobilized by thin silica-PVA sol-gel film on gold electrode surface. A rapid and direct electron transfer of SOD in the thin sol-gel film at the gold electrode was realized without any mediators or promoters. The characterization of the SOD electrodes showed a quasi-reversible electrochemical redox behavior with a formal potential of 80 + 5 mV (versus SCE) in 50 mmol l(-1) phosphate buffer solution (PBS), pH 7.0. The heterogeneous electron transfer rate constant was evaluated to be about 2.1s(-1). The anodic and cathodic transfer coefficients are 0.6 and 0.4, respectively. Based on biomolecular recognition for specific reactivity of SOD toward O(2)*- the SOD electrode was applied to a sensitive and selective measurement of O(2)*- with the low operation potential (-0.15 V versus SCE) in phosphate buffer solution, pH 7.0. The amperometric response was proportional to O(2)*- concentration in the range of 0.2-1.6 micromol l(-1) and the detection limit was 0.1 micromol l(-1) at a signal-to-noise ration of 3. The preparation of SOD electrode is easy and simple. The uniform porous structure of the silica-PVA sol-gel matrix results in a fast response rate of immobilized SOD and is very efficient for stabilizing the enzyme activity.     

Development of DNA electrochemical biosensor based on covalent immobilization of probe DNA by direct coupling of sol-gel and self-assembly technologies

A new procedure for fabricating deoxyribonucleic acid (DNA) electrochemical biosensor was developed based on covalent immobilization of target single-stranded DNA (ssDNA) on Au electrode that had been functionalized by direct coupling of sol-gel and self-assembled technologies. Two siloxanes, 3-mercaptopropyltrimethoxysiloxane (MPTMS) and 3-glycidoxypropyltrimethoxysiloxane (GPTMS) were used as precursors to prepare functionally self-assembly sol-gel film on Au electrode. The thiol group of MPTMS allowed assembly of MPTMS sol-gel on gold electrode surface. Through co-condensation between silanols, GPTMS sol-gel with epoxide groups interconnected into MPTMS sol-gel and enabled covalent immobilization of target NH(2)-ssDNA through epoxide/amine coupling reaction. The concentration of MPTMS and GPTMS influenced the performance of the resulting biosensor due to competitive sol-gel process. The linear range of the developed biosensor for determination of complementary ssDNA was from 2.51 x 10(-9) to 5.02 x 10(-7)M with a detection limit of 8.57 x 10(-10)M. The fabricated biosensor possessed good selectivity and could be regenerated. The covalent immobilization of target ssDNA on self-assembled sol-gel matrix could serve as a versatile platform for DNA immobilization and fabrication of biosensors.     

Preliminary investigation of a bioelectrochemical sensor for the detection of phenol vapours

This work investigates the feasibility of constructing a bioelectrochemical sensor that can operate directly in gases. A series of experiments are described, resulting in a sensor that is responsive to phenol vapours. The sensor was based on ionically conducting films that incorporate a biological redox catalyst at the surface of an array of interdigitated microband electrodes. Exposure to phenol vapour drives the bioelectrochemical reaction, providing a basis for a current signal under constant potential conditions. Ionic materials included Nafion and films based on tetrabutylammonium toluene-4-sulphonate (TBATS). The quasi-reversible electrode reaction of potassium hexacyanoferrate (II) within TBATS was investigated as a function of drying time. E^o′ and K⁰ were determined at a TBATS modified microdisc electrode under steady-state conditions. Drying time (water loss) from the TBATS film had the effect of increasing the film ionic strength. It was shown that as the film ionic strength increased, E⁰′ for potassium hexacyanoferrate (II) shifts toward positive potentials (because of ion pairing) and there was a corresponding increase in the heterogeneous rate constant K⁰. The latter effect was attributed to increasing ion-ion (cation-ferrocyanide ion) interactions as the film dried and the enhancing effect this had on the prevention of surface poisoning reactions at the electrode. These factors are discussed in relation to sensor design.     

Theoretical study of oxyhemocyanin active site: a possible insight on the first step of phenol oxidation by tyrosinase.

Extended Huckel theory calculations have been carried out on a model of the oxyhemocyanin active site that includes six imidazoles, the two copper cations, and a dioxygen molecule. The results obtained for the very likely mu-eta 2:eta 2 arrangement of the dioxygen molecule show that the most favorable orientation of O2 is such that the two long Cu-N coordination bonds are perpendicular to the plane formed by the two metal atoms and O2. This arrangement leads to pentacoordinated coppers with a distorted square pyramidal geometry. The molecular electrostatic potential maps of the complexes exhibit a potential well located close to the peroxo anion midbond. The dependence of the energy and of the molecular electrostatic maps on the precise orientation and location of the imidazole rings has been investigated. These results, which show the important role played by the third remote imidazole ligand, are discussed in relation with the first step of tyrosinase-mediated phenol oxidation.     

Reagentless biosensor for hydrogen peroxide based on immobilization of protein in zirconia nanoparticles enhanced grafted collagen matrix

A novel matrix, zirconia nanoparticles enhanced grafted collagen (ZrO2-grafted collagen) hybrid composite, for immobilization of protein and biosensing was developed. The scanning electron microscopy, UV-vis and Fourier transform infrared spectra, and electrochemical measurements showed that the matrix was well biocompatible and could retain the bioactivity of immobilized protein to a large extent. The direct electron transfer of the immobilized myoglobin (Mb) exhibited a couple of stable and well-defined redox peaks with the formal potential of -336 mV (versus SCE) in 0.1M pH 7.0 PBS. This matrix could accelerate the electron transfer between Mb and the electrode with a surface-controlled process and an electron transfer rate constant of 3.58+/-0.35s-1 at 10-500 mVs-1. The Mb immobilized in the matrix showed a high thermal stability up to 70 degrees C and an electrocatalytic activity to the reduction of hydrogen peroxide (H2O2) without the help of an electron mediator. The linear response range of the biosensor to H2O2 concentration was from 1.0 to 85.0 microM with the limit of detection of 0.63 microM at a signal-to-noise ratio of 3sigma. The biosensor exhibited high sensitivity, acceptable stability and reproducibility. This work opened a way for the further study on the direct electron transfer and biosensing application of the immobilized protein in collagen-related matrices.     

Colloidal gold as a biocompatible immobilization matrix suitable for the fabrication of enzyme electrodes by electrodeposition

Glucose oxidase, horseradish peroxidase, xanthine oxidase, and carbonic anhydrase have been adsorbed to colloidal gold sols with good retention of enzymatic activity. Adsorption of xanthine oxidase on colloidal gold did not result in a change in enzymatic activity as determined by active site titration with the stoichiometric inhibitor pterin aldehyde and by measurement of the apparent Michaelis constant (K'(M)). Gold sols with adsorbed glucose oxidase, horseradish peroxidase, and xanthine oxidase have also been electrodeposited onto conducting matrices (platinum gauze and/or glassy carbon) to make enzyme electrodes. These electrodes retained enzymatic activity and, more importantly, gave an electrochemical response to the enzyme substrate in the presence of an appropriate electron transfer mediator. Our results demonstrate the utility of colloidal gold as a biocompatible enzyme imobilization matrix suitable for the fabrication of enzyme electrodes. (c) 1992 John Wiley & Sons, Inc.     

A His-tag based immobilization method for the preparation and reconstitution of apoflavoproteins

The NifL PAS domain from Azotobacter vinelandii is a flavoprotein with FAD as the prosthetic group. Here we describe a novel immobilization procedure for the large-scale preparation of apo NifL PAS domain and its efficient reconstitution with either 2,4a-13C-FAD or 2,4a-13C-FMN. In this procedure, the His-tagged holoprotein is bound to an immobilized metal affinity column and the flavin is released by washing the column with buffer containing 2 M KBr and 2 M urea. The apoprotein is reconstituted on-column with the (artificial) flavin cofactor, and then eluted with buffer containing 250 mM imidazole. Alternatively, the immobilized apoprotein can be released from the column matrix before reconstitution.The His-tag based immobilization method of preparing reconstituted (or apo) NifL PAS domain protein has the advantage that it combines a protein affinity chromatography technique with limited protein loss, resulting in a high protein yield with extremely efficient flavin reconstitution. This on-column reconstitution method can also be used in cases where the apoprotein is unstable. Therefore, it may develop as a universal method for replacement of flavin or other cofactors.     

A new method for immobilization of microbial cells by cross-linking

A method for immobilization of microbial cells was designed. The method uses generation of reactive aldehyde groups on the cell wall surface under conditions of periodate oxidation. The linking of aldehyde groups by various bifuctional aromatic diamines and then by glutaraldehyde produced immobilized cells, which are promising for use in biocatalysis with high-molecular-weight substrates.     

The use of silica gel prepared by sol-gel method and polyurethane foam as microbial carriers in the continuous degradation of phenol

A mixed microbial culture was immobilized by entrapment into silica gel (SG) and entrapment/ adsorption on polyurethane foam (PU) and ceramic foam. The phenol degradation performance of the SG biocatalyst was studied in a packed-bed reactor (PBR), packed-bed reactor with ceramic foam (PBRC) and fluidized-bed reactor (FBR). In continuous experiments the maximum degradation rate of phenol (q _s ^max) decreased in the order: PBRC (598 mg l⁻¹h⁻¹) > PBR (PU, 471 mg l⁻¹h⁻¹) > PBR (SG, 394 mg l⁻¹h⁻¹) > FBR (PU, 161 mg l⁻¹h⁻¹) > FBR (SG, 91 mg l⁻¹ h⁻¹). The long-term use of the SG biocatalyst in continuous phenol degradation resulted in the formation of a 100–200 μm thick layer with a high cell density on the surface of the gel particles. The abrasion of the surface layer in the FBR contributed to the poor degradation performance of this reactor configuration. Coating the ceramic foam with a layer of cells immobilized in colloidal SiO₂ enhanced the phenol degradation efficiency during the first 3 days of the PBRC operation, in comparison with untreated ceramic packing. Received: 2 December 1999 / Revision received: 2 February 2000 / Accepted: 4 February 2000     

Electrochemical immunoassay of membrane P-glycoprotein by immobilization of cells on gold nanoparticles modified on a methoxysilyl-terminated butyrylchitosan matrix

A strategy to detect P-glycoprotein (P-gp) on cell membrane and quantify the cell number using electrochemical immunoassay was developed by effective surface immunoreactions and immobilization of cells on a highly hydrophilic interface, which was constructed by adsorption of colloidal gold nanoparticles on a methoxysilyl-terminated (Mos) butyrylchitosan modified glassy carbon electrode (Au-CS/GCE). Atomic force microscopy studies proved that the nanoparticles adsorbed on Mos-butyrylchitosan were efficient in preventing the cell leakage and retaining the activity of immobilized living K562/ADM leukemic cells. The incubation with P-gp monoclonal antibody and then the secondary alkaline phosphatase (AP) conjugated antibody introduced AP onto the K562/ADM cell immobilized on Au-CS/GCE. The bound AP led to an amperometric response of 1-naphthyl phosphate. Under optimal conditions the response was proportional to the logarithm of cell concentration in the range from 5.0 x 10(4) to 1.0 x 10(7) cells mL(-)(1) with a detection limit of 1.0 x 10(4) cells mL(-)(1). The results were comparable to flow cytometric analysis of P-gp expression. This proposed method was practical, convenient, and significant in the clinic and cytobiology.