Polymerization study of o-Si(OH)4 and complexation with Am(III), Eu(III) and Cm(III)

The stability constants of Am⁺³, Cm³⁺ and Eu³⁺ with ortho silicate, were measured at pH 3.50 and in ionic strengths of 0.20-1.00 M (NaClO₄) by the solvent extraction method. The Am⁺³, Cm³⁺ and Eu³⁺ forms 1:1 complex with ortho silicate ion at pH 3.60 with the stability constant (log β₁) value of 8.02 ± 0.10, 7.78 ± 0.08 and 7.81 ± 0.11, respectively. The stability of these metal ions decrease with increased ionic strength from 0.20 to 1.00 M (NaClO₄) for silicic acid concentrations of 0.002-0.020 M. Increasing silicic acid concentration above 0.02 M increased the amount of M³⁺ extracted into the organic phase, contrary to the trend usually observed for increased ligand concentration in solvent extraction. This reversed trend is likely due to the extraction of cationic species of silicic acid by HDEHP. Aging time (60-300 min) had no effect on the stability constant of these metal ions for 0.002-0.020 M silicic acid at pH 3.50 and I = 0.20 M (NaClO₄).The fraction of polymeric silicic acid present in solutions of 0.20-4.50 M NaClO₄ solutions at pH 3.0-10.0, T = 0-60 °C and aging time = 5-300 min was measured for determination of the silicomolybdate reaction to ascertain the proper conditions to study metal-silicate complexation.     

Photoluminescence profiles and fast/slow annealing effects of Eu(III)/Tb(III)‐codoped silica phosphor materials

A silica (SiO₂) nanoparticle matrix was codoped with luminescent Eu(III) and Tb(III) ions using a modified Stöber method. The effects of fast and slow thermal annealing on photoluminescence profile imaging were examined. Slow annealing treatment suppressed more quenching sites than fast thermal annealing to further increase the photoluminescence signals. The photoluminescence signals observed between 450 and 720 nm were assigned to the ⁵D₀ → ⁷F_J (J = 0,1,2,3,4) of Eu(III) and the ⁵D₄ → ⁷F_J (J = 6,5,4,3) transitions of Tb(III). Photoluminescence was largely sensitized by indirect excitation and was much stronger than that generated by direct excitation. The Eu(III) and Tb(III) ions were doped at lower symmetry sites in the silica matrix. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis,structure and density functional theory calculations of a novel photoluminescent trisarylborane–bismuth(III) complex

A novel trisarylborane–Bi(III) complex, tris(4‐(dimesitylboryl)phenyl)bismuthine [Bi(PhBMes₂)₃], in which (Ph = phenyl, and Mes = mesityl), was synthesized via the reaction of bismuth (III) chloride (BiCl₃) with three equivalents of lithiated (4‐bromophenyl)‐ dimesitylborane [BrPhBMes₂]. The new trisarylbismuthine was characterized by elemental analysis, ultraviolet–visible (UV–vis) spectroscopy, and NMR (¹H and ¹³C) spectroscopy. The molecular structure of Bi(PhBMes₂)₃ in the solid state was determined using single‐crystal X‐ray diffraction analysis, which showed short intermolecular C–H···H–C contact. The complex is a fluorescent emitter (λ_max = 395 nm) at room temperature and a phosphorescent emitter (λ_max = 423 nm) at 77 K, which displayed a long lifetime of 495 ms. The UV–vis transitions were investigated using density function theory (DFT) and time‐dependent (TD)‐DFT calculations. Natural bond orbital analysis showed that the bismuth (III) center was mainly Lewis acidic in nature.     

EPR and H NMR spectroscopy and DFT study of pentaammineruthenium(III)phenylcyanamide complexes

The EPR and ¹H NMR spectroscopy of seven [Ru(NH₃)₅L]²⁺ complexes, where L = 3,5-dimethoxyphenylcyanamide (MeO₂pcyd), 3,4,5-trimethoxyphenylcyanamide (MeO₃pcyd), 4-nitrophenylcyanamide (NO₂pcyd), 2,3-dichlorophenylcyanamide (Cl₂pcyd), 2,4,6-trichlorophenylcyanamide (Cl₃pcyd), 2,3,5,6-tetrachlorophenylcyanamide (Cl₄pcyd) and pentachlorophenylcyanamide (Cl₅pcyd), was performed. EPR spectra of the complexes showed an axial signal with g_|| and g_⊥ at high and low field, respectively. The g_|| axis is suggested to lie along the Ru-cyanamide bond. Gas-phase DFT calculations of [Ru(NH₃)₅ phenylcyanamide]²⁺ showed spin density localized mostly on the phenylcyanamide ligand, in disagreement with EPR data. DFT/polarizable continuum model (PCM, water solvation) calculations shifted spin density towards ruthenium so that spin density was shared between ruthenium and phenylcyanamide ligand. Proton contact shifts were determined from NMR and EPR data and were used to estimate spin density distributions on phenyl ring carbons. The results showed that the DFT/PCM calculation overestimated spin density on phenyl ring carbons by approximately one order of magnitude. Donor-acceptor interactions between the solute and solvent that are not fully accounted for in the DFT/PCM method are suggested to stabilize the Ru(III) oxidation state.     

Synthesis and luminescence properties of novel 8‐hydroxyquinoline derivatives and their Eu(III) complexes

Six novel 8‐hydroxyquinoline derivatives were synthesized using 2‐methyl‐8‐hydroxyquinoline and para‐substituted phenol as the main starting materials, and were characterized by ¹H nuclear magnetic resonance (NMR), mass spectrometry (MS), ultraviolet (UV) light analysis and infra‐red (IR) light analysis. Their complexes with Eu(III) were also prepared and characterized by elemental analysis, molar conductivity, UV light analysis, IR light analysis, and thermogravimetric–differential thermal analysis (TG–DTA). The results showed that the ligand coordinated well with Eu(III) ions and had excellent thermal stability. The structure of the target complex was EuY^1–6(NO₃)₃.2H₂O. The luminescence properties of the target complexes were investigated, the results indicated that all target complexes had favorable luminescence properties and that the introduction of an electron‐donating group could enhance the luminescence intensity of the corresponding complexes, but the addition of an electron‐withdrawing group had the opposite effect. Among all the target complexes, the methoxy‐substituted complex (–OCH₃) had the highest fluorescence intensity and the nitro‐substituted complex (–NO₂) had the weakest fluorescence intensity. The results showed that 8‐hydroxyquinoline derivatives had good energy transfer efficiency for the Eu(III) ion. All the target complexes had a relatively high fluorescence quantum yield. The fluorescence quantum yield of the complex EuY³(NO₃)₃.2H₂O was highest among all target complexes and was up to 0.628. Because of excellent luminescence properties and thermal stabilities of the Eu(III) complexes, they could be used as promising candidate luminescent materials.     

The preparation and structural characterisation of thiolato anions of bismuth(III)

The preparation and structures of the bismuth thiolato anions [Bi₂(SC₆F₅)₆(μ-SC₆F₅)]⁻ and [Bi₂(SC₆F₅)₆(μ-SC₆F₅)₂]²⁻ and the halothiolato anions [Bi₂(SC₆F₅)₆(μ-Br)]⁻, [Bi₂(SC₆F₅)₆(μ-Cl)₂]²⁻ and [Bi₃(SC₆F₅)₉(μ-Br)₂]²⁻ are described. All compounds have been isolated from reactions between Bi(SC₆F₅)₃ and ammonium or phosphonium halides. The basic structural units in the dinuclear species are of two types namely [Bi₂(SR)₆(μ-X)]⁻ and [Bi₂(SR)₆(μ-X)₂]²⁻, where X=thiolate or halide. In the former case the single bridging groups occupy an axial site within the disphenoidal (equatorially vacant, trigonal bipyramidal) geometry around the bismuth centres whereas in the latter the two bridging groups occupy cis basal sites in square based pyramidal bismuth environments. The trinuclear anion [Bi₃(SC₆F₅)₉(μ-Br)₂]²⁻ has features in common with the basic [Bi₂(SC₆F₅)₆(μ-Br)]⁻ unit.     

Complexation study of europium(III) and curium(III) with urea in aqueous solution investigated by time-resolved laser-induced fluorescence spectroscopy

The complex formation of europium(III) and curium(III) with urea in aqueous solution has been studied at I = 0.1 M (NaClO₄), room temperature and trace metal concentrations in the pH-range of 1-8 at various ligand concentrations using time-resolved laser-fluorescence spectroscopy. While for curium(III) the luminescence maximum is red shifted upon complexation, in case of europium(III) emission wavelengths remain unaltered but a significant change in peak splitting occurs. Both heavy metals form weak complexes of the formulae ML³⁺ and MLOH²⁺ with urea. Stability constants were determined to be log β₁₁₀ = −0.12 ± 0.05 and log β_11-1 = −6.86 ± 0.15 for europium(III) and log β₁₁₀ = −0.28 ± 0.12 and log β_11-1 = −7.01 ± 0.15 for curium(III).     

Iron (III) Stimulation of Lipid Hydroperoxide-Dependent Lipid Peroxidation

In an experimental system where both Fe²⁺ autoxidation and generation of reactive oxygen species is negligible, the effect of FeCl₂ and FeCl₃ on the peroxidation of phosphatidylcholine (PC) liposomes containing different amounts of lipid hydroperoxides (LOOH) was studied; Fe²⁺ oxidation, oxygen consumption and oxidation index of the liposomes were measured. No peroxidation was observed at variable FeCl₂/FeCl₃ ratio when PC liposomes deprived of LOOH by triphenyl-phosphine treatment were utilized. By contrast, LOOH containing liposomes were peroxidized by FeCl₂. The FeCl₂ concentration at which Fe²⁺ oxidation was maximal, defined as critical Fe²⁺ concentration [Fe²⁺]*, depended on the LOOH concentration and not on the amount of PC liposomes in the assay. The LOOH-dependent lipid peroxidation was stimulated by FeCl₃, addition; the oxidized form of the metal increased the average length of radical chains, shifted to higher values the [Fe²⁺]* and shortened the latent period. The iron chelator KSCN exerted effects opposite to those exerted by FeCl₃ addition. The experimental data obtained indicate that the kinetics of LOOH-dependent lipid peroxidation depends on the Fe²⁺/Fe³⁺ ratio at each moment during the time course of lipid peroxidation. The results confirm that exogenously added FeCl₃ does not affect the LOOH-independent but the LOOH-deendent lipid peroxidation; and suggest that the Feg, endogenously generated exerts a major role in the control of the LOOH-dependent lipid peroxidation.     

Iron (III) Stimulation of Lipid Hydroperoxide-Dependent Lipid Peroxidation

In an experimental system where both Fe²⁺ autoxidation and generation of reactive oxygen species is negligible, the effect of FeCl₂ and FeCl₃ on the peroxidation of phosphatidylcholine (PC) liposomes containing different amounts of lipid hydroperoxides (LOOH) was studied; Fe²⁺ oxidation, oxygen consumption and oxidation index of the liposomes were measured. No peroxidation was observed at variable FeCl₂/FeCl₃ ratio when PC liposomes deprived of LOOH by triphenyl-phosphine treatment were utilized. By contrast, LOOH containing liposomes were peroxidized by FeCl₂. The FeCl₂ concentration at which Fe²⁺ oxidation was maximal, defined as critical Fe²⁺ concentration [Fe²⁺]*, depended on the LOOH concentration and not on the amount of PC liposomes in the assay. The LOOH-dependent lipid peroxidation was stimulated by FeCl₃, addition; the oxidized form of the metal increased the average length of radical chains, shifted to higher values the [Fe²⁺]* and shortened the latent period. The iron chelator KSCN exerted effects opposite to those exerted by FeCl₃ addition. The experimental data obtained indicate that the kinetics of LOOH-dependent lipid peroxidation depends on the Fe²⁺/Fe³⁺ ratio at each moment during the time course of lipid peroxidation. The results confirm that exogenously added FeCl₃ does not affect the LOOH-independent but the LOOH-deendent lipid peroxidation; and suggest that the Feg, endogenously generated exerts a major role in the control of the LOOH-dependent lipid peroxidation.     

Reactions and structures in the gallium(III)/indium(III)-N,N-dimethylthioformamide systems

The structure of the N,N-dimethylthioformamide (DMTF) solvated gallium(III) ion has been determined in solution by means of extended X-ray absorption fine structure (EXAFS) spectroscopy. The gallium(III) ion is four-coordinate in tetrahedral fashion with a mean Ga-S bond distance of 2.233(2) Å in DMTF solution. At the dissolution of indium(III) perchlorate or trifluoromethanesulfonate in DMTF coordinated solvent molecules are partly reduced to sulfide ions, and a tetrameric complex with the composition [In₄S₄(SHN(CH₃)₂)₁₂]⁴⁺ is formed. The structure of the solid tetrameric complex in the perchlorate salt was solved with single crystal X-ray diffraction. Four indium(III) ions and four sulfide ions form a highly symmetric heterocubane structure where each indium binds three bridging sulfide ions and each sulfide ion binds three indium(III) ions with a mean In-S bond distance of 2.584(1) Å, and S-In-S angles of 90.3(1)°. Each indium(III) additionally binds three DMTF molecules at significantly longer mean In-S bond distance, 2.703(1) Å; the S-In-S angles are in the range 80.3-90.4°. Large angle X-ray scattering data on a DMTF solution of indium(III) trifluoromethanesulfonate show that the same tetrameric species characterized in the solid state is also present in solution, whereas the EXAFS measurements only give information about the In-S bond distances due to the short core hole lifetime.     

Secondary ligand-metal interactions in rhodium(III) and iridium(III) phosphoramidite complexes

The synthesis, characterization, and application in asymmetric catalytic cyclopropanation of Rh(III) and Ir(III) complexes containing (S_a,R_C,R_C)-O,O′-[1,1′-binaphthyl-2,2′-diyl]-N,N′-bis[1-phenyl-ethyl]phosphoramidite (1) are reported. The X-ray structures of the half-sandwich complexes [MCl₂(C₅Me₅)(1,κP)] (M = Rh, 2a; M = Ir, 2b) show that the metal-phosphoramidite bond is significantly shorter in the Ir(III) analog. Chloride abstraction from 2a (with CF₃SO₃SiMe₃ or with CF₃SO₃Me) and from 2b (with AgSbF₆) gives the cationic species [MCl(C₅Me₅)(1,2-η-1,κP)]⁺ (M = Rh, 3a; M = Ir, 3b), which display a secondary interaction between the metal and a dangling phenethyl group (NCH(CH₃)Ph) of the phosphoramidite ligand, as indicated by NMR spectroscopic studies. Complexes 3a and 3b slowly decompose in solution. In the case of 3b, the binuclear species [Ir₂Cl₃(C₅Me₅)₂]⁺ is slowly formed, as indicated by an X-ray study. Preliminary catalytic tests showed that 3a cyclopropanates styrene with moderate yield (35%) and diastereoselectivity (70:30 trans:cis ratio) and with 32% ee (for the trans isomer).     

Adsorption of Eu3+ and Am3+ ion towards hard donor-based diglycolamic acid-functionalised carbon nanotubes: density functional theory guided experimental verification

Structure, bonding, energetic and thermodynamic parameters of trivalent Eu³⁺ and Am³⁺ with diglycolamic acid-functionalised carbon nanotubes (CNT–DGA) in gas and solvent phases are reported in order to understand their complexation and extraction behaviour. The calculation was performed with generalised gradient approximated BP86 density functional and hybrid B3LYP functional using SVP/TZVP basis set. The free energy of extraction, ΔG_ext, of Eu³⁺ and Am³⁺ was computed using the Born–Haber thermodynamic cycle in conjunction with conductor-like screening model solvation approach. The calculated free energy of extraction was found to be exergonic using an explicit cluster water model for hydrating the ions and it was found to be higher for Eu³⁺ ion over Am³⁺ ion. From the estimated distribution constant using synthesised CNT–DGA, it is indisputably established that the Eu³⁺ ion is preferentially extracted over Am³⁺ ion and hence confirms the acceptance of the explicit cluster model for ion solvation free energy and thermodynamic cycle for the evaluation of free energy of extraction in solution phase. This is perhaps the first of its kind that a combined theoretical and experimental study has been performed on the free energy of extraction of Eu³⁺ and Am³⁺ using CNT–DGA.     

A dinuclear copper(II) complex with a Cu(O, N-O)Cu bridging core: structural and magnetic (experimental and density functional theory) studies

The molecular and electronic structure, along with the magnetic properties of a dinuclear complex in which two copper ions interact through a phenoxo oxygen atom and an oximato group are presented. The complex [CuL³Cu(O₂CCH₃)]3H₂O ·  0.5CH₃OH (3) crystallizes in the monoclinic space group Cc, with a=28.432(2) Å, b=12.305(1) Å, c=13.159(1) Å and β=99.580(9)°. The X-ray molecular structure shows that the core of the molecule comprising the two metal ions and the seven neighboring donors is nearly planar. The copper(II) ions were found to be antiferromagnetically coupled with a singlet-triplet splitting of 764(4) cm⁻¹. Density Functional Theory (DFT) showed that the magnetic orbitals are largely delocalized towards the bridging area, and an antiferromagnetic interaction in good agreement with the experimental data was computed using the Broken Symmetry (BS) formalism to obtain the energy of the singlet state.     

Iron(III), chromium(III) and cobalt(II) complexes with squarate: Synthesis, crystal structure and magnetic properties

The preparation and variable temperature-magnetic investigation of three squarate-containing complexes of formula [Fe₂(OH)₂(C₄O₄)₂(H₂O)₄]·2H₂O (1) [Cr₂(OH)₂(C₄O₄)₂(H₂O)₄]·2H₂O (2) and [Co(C₄O₄)(H₂O)₄]_n (3) [H₂C₄O₄ = 3.4-dihydroxycyclobutene-1,2-dione (squaric acid)] together with the crystal structures of 1 and 3 are reported. Complex 1 contains discrete centrosymmetric [Fe₂(OH)₂(C₄O₄)₂(H₂O)₄] diiron(II) units where the iron pairs are joined by a di-μ-hydroxo bridge and two squarate ligands acting as bridging groups through adjacent oxygen atoms. Two coordinated water molecules in cis position complete the octahedral environment at each iron atom in 1. The iron-iron distance with the dinuclear unit is 3.0722(6) Å and the angle at the hydroxo bridge is 99.99(7)°, values which compare well with the corresponding ones in the isostructural compound 2 (2.998 Å and 99.47°) whose structure was reported previously. The crystal structure of 3 contains neutral chains of squarato-O¹,O³-bridged cobalt(II) ions where four coordinated water molecules complete the six-coordination at each cobalt atom. The cobalt-cobalt separation across the squarate bridge is 8.0595(4) Å. A relatively important intramolecular antiferromagnetic coupling occurs in 1 whereas it is very weak in 2, the exchange pathway being the same [J = −14.4 (1) and −0.07 cm⁻¹ (2), the spin Hamiltonian being defined as ]. A weak intrachain antiferromagnetic interaction between the high-spin cobalt(II) ions occurs in 3 (J = −0.30 cm⁻¹). The magnitude and nature of these magnetic interactions are discussed in the light of their respective structures and they are compared with those reported for related systems.     

Effect of praseodymium(III) on zinc(II) species in human interstitial fluid

A multiphase model of metal ion species in human interstitial fluid was constructed under physiological conditions. The effect of Pr(III) on Zn(II) species was studied. At the normal conditions, Zn(II) species mainly distribute in [Zn(HSA)], [Zn(IgG)], and [Zn(Cys)₂H]⁺. With the Pr(III) level increased, the apparent competition of Pr(III) for ligands lead to the redistribution of Zn(II) species.     

Mononuclear single helices of lanthanum(III) and europium(III). Metal dependent diastereomeric excess

Using the 1:2 condensate of benzildihydrazone and 2-acetylpyridine as a tetradentate N donor ligand L, LaL(NO₃)₃ (1) and EuL(NO₃)₃ (2), which are pale yellow in colour, are synthesized. While single crystals of 1 could not be obtained, 2 crystallises as a monodichloromethane solvate, 2·CH₂Cl₂ in the space group Cc with a = 11.7099(5) Å, b = 16.4872(5) Å, c = 17.9224(6) Å and β = 104.048(4)°. From the X-ray crystal structure, 2 is found to be a rare example of monohelical complex of Eu(III). Complex 1 is diamagnetic. The magnetic moment of 2 at room temperature is 3.32 BM. Comparing the FT-IR spectra of 1 and 2, it is concluded that 1 also is a mononuclear single helix. ¹H NMR reveals that both 1 and 2 are mixtures of two diastereomers. In the case of the La(III) complex (1), the diastereomeric excess is only 10% but in the Eu(III) complex 2 it is 80%. The occurrence of diastereomerism is explained by the chiralities of the helical motif and the type of pentakis chelates present in 1 and 2.     

Binding study of lysozyme with Al(III) using chemiluminescence analysis

The binding behavior of lysozyme with Al(III) is described using luminol as a luminescence probe by flow injection–chemiluminescence (FI–CL) analysis. It was found that the CL intensity of the luminol–lysozyme reaction could be markedly enhanced by Al(III), and the increase in CL intensity was linear with the Al(III) concentration over the range 0.3–30.0 pg mL^?1, with a detection limit of 0.1 pg mL^?1 (3σ). Based on the interaction model of lysozyme with Al(III), lg[(I ? I₀)/(2I₀ ? I)] = lgK + nlg[M], the binding constant K = 6.84 × 10⁶ L mol^–1 and the number of binding sites (n) = 0.76. The relative standard deviations were 3.2, 2.4 and 2.0% for 10.0, 20.0 and 30.0 pg mL^?1 Al(III) (n = 7), respectively. This new method was successfully applied to continuous, quantitative monitoring of picogram level Al(III) in human saliva following oral intake of compound aluminum hydroxide tablets. It was found that Al(III) in saliva reached a maximum of 101.2 ng mL^?1 at 3.0 h. The absorption rate constant k_a, elimination rate constant k and half‐life time t_1/2 of Al(III) were 1.378 h^?1, 0.264 h^?1 and 2.624 h, respectively. Copyright © 2013 John Wiley & Sons, Ltd.     

Safety of an oxygen-coordinated niacin-bound chromium(III) complex (NBC): II. Developmental toxicity study in rats

The objective of the present study was to evaluate the teratogenic potential of a novel oxygen-coordinated niacin-bound chromium complex (NBC) in Sprague-Dawley rats. Due to its potential to affect fat synthesis and reduce food intake, processes which are often crucial in normal fetal development, this teratology study was undertaken as part of a multi-generation reproductive investigation. The animals in this study were selected randomly after weaning from each F_2b litter of the F1 generation from the two-generation reproductive toxicity study. To start the teratology study, Sprague-Dawley rat pups (∼30/sex/group) from the F_2b generation were allowed to grow up to 10-12 weeks of age before mating. The rats in treatment group were exposed directly to NBC through feed. The dietary exposure levels were the same as those employed for the two-generation reproductive toxicity study, viz. 4, 15, or 60 ppm. Following mating at maturity, the pregnant rats were observed daily for clinical signs of adverse effects, and body weight and feed consumption were recorded. On the day 20th of the gestation, animals were subjected to a necropsy and caesarean section to examine the uterus, ovaries and fetuses for assessment of different parameters of pregnancy and embryo-fetal defects. In this study, no indications of maternal toxicity, adverse effects on the parameters evaluated for the gravid uteri, external abnormalities in the fetuses, soft tissue abnormalities in the fetuses, or skeletal abnormalities in the fetuses were noted. Based on the results of this developmental toxicity study, NBC was found to benon-teratogenic in Sprague-Dawley rat, at the dietary exposure levels of 4, 15, and 60 ppm, equivalent to the dose levels of 0.50, 2.0, or 8.0 mg/kg/day, respectively.