Highly stable enzyme precipitate coatings and their electrochemical applications

This paper describes highly stable enzyme precipitate coatings (EPCs) on electrospun polymer nanofibers and carbon nanotubes (CNTs), and their potential applications in the development of highly sensitive biosensors and high-powered biofuel cells. EPCs of glucose oxidase (GOx) were prepared by precipitating GOx molecules in the presence of ammonium sulfate, then cross-linking the precipitated GOx aggregates on covalently attached enzyme molecules on the surface of nanomaterials. EPCs-GOx not only improved enzyme loading, but also retained high enzyme stability. For example, EPC-GOx on CNTs showed a 50 times higher activity per unit weight of CNTs than the conventional approach of covalent attachment, and its initial activity was maintained with negligible loss for 200 days. EPC-GOx on CNTs was entrapped by Nafion to prepare enzyme electrodes for glucose sensors and biofuel cells. The EPC-GOx electrode showed a higher sensitivity and a lower detection limit than an electrode prepared with covalently attached GOx (CA-GOx). The CA-GOx electrode showed an 80% drop in sensitivity after thermal treatment at 50°C for 4 h, while the EPC-GOx electrode maintained its high sensitivity with negligible decrease under the same conditions. The use of EPC-GOx as the anode of a biofuel cell improved the power density, which was also stable even after thermal treatment of the enzyme anode at 50°C. The excellent stability of the EPC-GOx electrode together with its high current output create new potential for the practical applications of enzyme-based glucose sensors and biofuel cells.     

Electrically Contacted Bienzyme‐Functionalized Mesoporous Carbon Nanoparticle Electrodes: Applications for the Development of Dual Amperometric Biosensors and Multifuel‐Driven Biofuel Cells

The capping of electron relay units in mesoporous carbon nanoparticles (MPC NPs) by crosslinking of different enzymes on MPC NPs matrices leads to integrated electrically contacted bienzyme electrodes acting as dual biosensors or as functional bienzyme anodes and cathodes for biofuel cells. The capping of ferrocene methanol and methylene blue in MPC NPs by the crosslinking of glucose oxidase (GOx) and horseradish peroxidase (HRP) yields a functional sensing electrode for both glucose and H₂O₂, which also acts as a bienzyme cascaded system for the indirect detection of glucose. A MPC NP matrix, loaded with ferrocene methanol and capped by GOx/lactate oxidase (LOx), is implemented for the oxidation and detection of both glucose and lactate. Similarly, MPC NPs, loaded with 2,2′‐azino‐bis(3‐ethylbenzo­thiazoline‐6‐sulphonic acid), are capped with bilirubin oxidase (BOD) and catalase (Cat), to yield a bienzyme O₂ reduction cathode. A biofuel cell that uses the bienzyme GOx/LOx anode and the BOD/Cat cathode, glucose and/or lactate as fuels, and O₂ and/or H₂O₂ as oxidizers is assembled, revealing a power efficiency of ≈90 μW cm^?2 in the presence of the two fuels. The study demonstrates that multienzyme MPC NP electrodes may improve the performance of biofuel cells by oxidizing mixtures of fuels in biomass.     

Activation of cellulose membranes with 1,1'-carbonyldiimidazole or 1-cyano-4-dimethylaminopyridinium tetrafluoroborate as a basis for the development of immunosensors

Methods for the activation of a cellulose dialysis membrane for immunosensor applications have been developed. For activation two reagents, 1,1'-carbonyldiimidazole (CDI) and 1-cyano-4-dimethylaminopyridinium tetrafluoroborate (CDAP), were compared with respect to the coupling efficiency for glucose oxidase (GOx) and 1,8-diamino-2,6-dioxaoctane. The maximum level of activation was 2.4 micromol cm(-2) for CDI and 0.2 micromol cm(-2) for CDAP activation. We observed 1.5 microg cm(-2) and 0.4 x 10(-4) U cm(-2) GOx with CDI-activated membranes whereas 1.7 microg cm(-2) and 7.2 x 10(-4) U cm(-2) GOx were observed with CDAP-activated membranes. With 1,8-diamino-2,6-dioxaoctane amino group densities of 0.165 and 0.09 micromol cm(-2) were observed via CDI and CDAP activation, respectively. An amino-modified membrane was used for coupling a ligand (pentapeptide) and an immunoenzymometric assay for hemoglobin A1c was carried out.     

Preserved enzymatic activity of glucose oxidase immobilized on unmodified electrodes for glucose detection

Glucose sensing electrodes have been realized by immobilizing glucose oxidase (GOx) on unmodified edge plane of highly oriented pyrolytic graphite (epHOPG) and the native oxide of heavily doped silicon (SiO2/Si). Both kinds of electrode show direct interfacial electron transfer due to the redox process of the immobilized GOx. The measured formal potential of the redox process agrees with that of the native enzyme, suggesting that the immobilized GOx has retained its enzymatic activity. The electron transfer rates of the GOx immobilized electrode are 2s(-1) for GOx/epHOPG electrode and 7.9s(-1) for GOx/SiO2/Si electrode, which are greater than those for which GOx is immobilized on modified electrodes, probably due to the fact that the enzyme makes direct contact to electrode surface. The preservation of the enzymatic activity of the immobilized GOx has been confirmed by observing the response of the GOx/epHOPG and GOx/SiO2/Si electrodes to glucose with a detection limit of 0.050 mM. The response signals the catalyzed oxidation of glucose and, therefore, confirms that the immobilized GOx retained its enzymatic activity. The properties of the electrode as a glucose sensor are presented.     

Directed evolution of glucose oxidase from Aspergillus niger for ferrocenemethanol-mediated electron transfer

A directed evolution protocol was developed for glucose oxidase (GOx) from Aspergillus niger that mimics applications conditions and employs a well-known mediator, oxidized ferrocenemethanol, in a medium throughput screen (96-well plate format). Upon reduction, oxidized ferrocenemethanol shows a color change from blue to pale yellow that can be recorded at 625 nm. Under optimized screening conditions, a CV of less than 20% was achieved in 96-well microtiter plates. For validating the screening system, two mutant libraries of GOx were generated by standard error-prone PCR conditions (0.04 mM MnCl(2)) and Saccharomyces cerevisiae was employed as host for secreted GOx expression. Two screening of approximately 2000 GOx mutants yielded a double mutant (T30S I94V) with improved pH and thermal resistance. Thermal resistance at a residual activity of 50% was increased from 58 degrees C (wild type, WT) to 62 degrees C (T30S I94V) and pH stability was improved at basic pH (pH 8-11). K(m) for glucose remained nearly unchanged (20.8 mM WT; 21.3 mM T30S I94V) and k(cat) increased (69.5/s WT; 137.7/s T30S I94V).     

Purification of glucose oxidase from complex fermentation medium using tandem chromatography

A fast and efficient purification method for recombinant glucose oxidase (rGOx) for flask fermentation scale (up to 2L) was designed for the purposes of characterization of rGOx mutants during directed protein evolution. The Aspergillus niger GOx was cloned into a pYES2-alphaMF-GOx construct and expressed extracellularly in yeast Saccharomyces cerevisiae. Hydrophobic interaction (HIC)/size exclusion (SEC)-tandem chromatographic system was designed for direct purification of rGOx from a conditioned complex expression medium with minimum preceding sample preparation (only adjustments to conductivity, pH and coarse filtering). HIC on Butyl 650s (50 mM ammonium acetate pH 5.5 and 1.5 M ammonium sulphate) absorbs GOx from the medium and later it is eluted by 100% stepwise gradient with salt free buffer directly into SEC column (Sephadex 200) for desalting and final polishing separation. The electrophoretic and UV-vis spectrophotometric analyses have proven enzyme purity after purification.     

A simple electrochemical approach to fabricate a glucose biosensor based on graphene-glucose oxidase biocomposite

We report a simple electrochemical approach for the immobilization of glucose oxidase (GOx) on reduced graphene oxide (RGO). The immobilization of GOx was achieved in a single step without any cross linking agents or modifiers. A simple solution phase approach was used to prepare exfoliated graphene oxide (GO), followed by electrochemical reduction to get RGO-GOx biocomposite. The direct electrochemistry of GOx was revealed at the RGO-GOx modified glassy carbon electrode (GCE). The electrocatalytic and electroanalytical applications of the proposed film were studied by cyclic voltammetry (CV) and amperometry. It is notable that the glucose determination has been achieved in mediator-free conditions. RGO-GOx film showed very good stability, reproducibility and high selectivity. The developed biosensor exhibits excellent catalytic activity towards glucose over a wide linear range of 0.1-27mM with a sensitivity of 1.85μAmM(-1)cm(-2). The facile and easy electrochemical approach used for the preparation of RGO-GOx may open up new horizons in the production of cost-effective biosensors and biofuel cells.     

Rational redesign of glucose oxidase for improved catalytic function and stability

Glucose oxidase (GOx) is an enzymatic workhorse used in the food and wine industries to combat microbial contamination, to produce wines with lowered alcohol content, as the recognition element in amperometric glucose sensors, and as an anodic catalyst in biofuel cells. It is naturally produced by several species of fungi, and genetic variants are known to differ considerably in both stability and activity. Two of the more widely studied glucose oxidases come from the species Aspergillus niger (A. niger) and Penicillium amagasakiense (P. amag.), which have both had their respective genes isolated and sequenced. GOx from A. niger is known to be more stable than GOx from P. amag., while GOx from P. amag. has a six-fold superior substrate affinity (K(M)) and nearly four-fold greater catalytic rate (k(cat)). Here we sought to combine genetic elements from these two varieties to produce an enzyme displaying both superior catalytic capacity and stability. A comparison of the genes from the two organisms revealed 17 residues that differ between their active sites and cofactor binding regions. Fifteen of these residues in a parental A. niger GOx were altered to either mirror the corresponding residues in P. amag. GOx, or mutated into all possible amino acids via saturation mutagenesis. Ultimately, four mutants were identified with significantly improved catalytic activity. A single point mutation from threonine to serine at amino acid 132 (mutant T132S, numbering includes leader peptide) led to a three-fold improvement in k(cat) at the expense of a 3% loss of substrate affinity (increase in apparent K(M) for glucose) resulting in a specify constant (k(cat)/K(M)) of 23.8 (mM(-1) · s(-1)) compared to 8.39 for the parental (A. niger) GOx and 170 for the P. amag. GOx. Three other mutant enzymes were also identified that had improvements in overall catalysis: V42Y, and the double mutants T132S/T56V and T132S/V42Y, with specificity constants of 31.5, 32.2, and 31.8 mM(-1) · s(-1), respectively. The thermal stability of these mutants was also measured and showed moderate improvement over the parental strain.     

High-performance amperometric biosensors and biofuel cell based on chitosan-strengthened cast thin films of chemically synthesized catecholamine polymers with glucose oxidase effectively entrapped

Rapid oxidation of dopamine (DA) or L-noradrenaline (NA) by K(3)Fe(CN)(6) yields poly(DA) (PDA(C)) or poly(NA) (PNA(C)) with glucose oxidase (GOx) effectively entrapped, and such an enzyme-entrapped catecholamine polymer is cast on an Au electrode followed by chitosan (CS) strengthening for biosensing and fabrication of a biofuel cell (BFC). The optimized glucose biosensor of CS/PDA(C)-GOx/Au displays an extremely high sensitivity up to 135 μA mM(-1) cm(-2), a very low limit of detection of 0.07 μM, a response time of <3 s, good suppression of interferents, striking thermostability (lifetime of 3 weeks at 60°C and over 2 months at 30°C), and high resistance to urea denaturation. The biosensor also works well in the second generation biosensing mode with p-benzoquinone (BQ) or ferrocene monocarboxylic acid (Fc) as an artificial mediator, with greatly broadened linear detection ranges (2.0 μM-48.0 mM for BQ and 2.0 μM-16.0 mM for Fc) and up to mA cm(-2)-scale glucose-saturated current density. The good permeability of artificial mediators across the enzyme film enables the quantification of the surface concentration of immobilized GOx on the basis of a reported kinetic model, and UV-Vis spectrophotometry is used to measure the enzymatic activity, revealing high enzymatic activity/load at CS/PDA(C)-GOx/Au. A BFC is also successfully fabricated with a bioanode of CS/PDA(C)-GOx/Au in phosphate buffer solution containing 100 mM glucose and 4.0 mM BQ and a carbon cathode in Nafion-membrane-isolated acidic KMnO(4), and its maximum power density of 1.62 mW cm(-2) is superior to those of most BFC hitherto reported.     

Enzyme precipitate coatings of glucose oxidase onto carbon paper for biofuel cell applications

Enzymatic biofuel cells (BFC) have a great potential as a small power source, but their practical applications are being hampered by short lifetime and low power density. This study describes the direct immobilization of glucose oxidase (GOx) onto the carbon paper in the form of highly stable and active enzyme precipitation coatings (EPCs), which can improve the lifetime and power density of BFCs. EPCs were fabricated directly onto the carbon paper via a three-step process: covalent attachment (CA), enzyme precipitation, and chemical crosslinking. GOx-immobilized carbon papers via the CA and EPC approaches were used as an enzyme anode and their electrochemical activities were tested under the BFC-operating mode. The BFCs with CA and EPC enzyme anodes produced the maximum power densities of 50 and 250 μW/cm(2) , respectively. The BFC with the EPC enzyme anode showed a stable current density output of >700 μA/cm(2) at 0.18 V under continuous operation for over 45 h. When a maple syrup was used as a fuel under ambient conditions, it also produced a stable current density of >10 μA/cm(2) at 0.18 V for over 25 h. It is anticipated that the direct immobilization of EPC on hierarchical-structured electrodes with a large surface area would further improve the power density of BFCs that can make their applications more feasible.     

Fabrication of a chitosan/glucose oxidase-poly(anilineboronic acid)-Au(nano)/Au-plated Au electrode for biosensor and biofuel cell

Enzyme immobilization is one of the key factors in constructing high-performance enzyme biosensors and biofuel cells (BFCs). Herein, we propose a new protocol for efficient immobilization of a glycoprotein enzyme based on the interaction of the 1, 2- or 1, 3-diols in the glycoprotein with a boronic acid functionalized monomer. Briefly, casting a mixture of glucose oxidase (GOx) and anilineboronic acid (ABA) followed by a NaAuCl(4) solution to an Au-plated Au electrode surface yielded a GOx-poly(ABA) (PABA)-gold nanoparticle (Au(nano)) bionanocomposite, and chitosan (CS) was then cast and air-dried. In the present protocol, the small-sized Au(nano) or Au subnanostructures can form near/on the enzyme molecule, which greatly promotes the electron transfer of enzymatic reaction and enhances the amperometric responses. The thus-prepared CS/GOx-PABA-Au(nano)/Au-plated Au electrode worked well in the first-/second generation biosensing modes and as a bioanode in a monopolar biofuel cell, with analytical or cell-power performance superior to those of most analogues hitherto reported.     

Triphenylmethane dyes, an alternative for mediated electronic transfer systems in glucose oxidase biofuel cells

The bioelectrochemical behavior of three triphenylmethane (TPM) dyes commonly used as pH indicators, and their application in mediated electron transfer systems for glucose oxidase bioanodes in biofuel cells was investigated. Bromophenol Blue, Bromothymol Blue, Bromocresol Green were compared bioelectrochemically against two widely used mediators, benzoquinone and ferrocene carboxy aldehyde. Biochemical studies were performed in terms of enzymatic oxidation, enzyme affinity, catalytic efficiency and co-factor regeneration. The different features of the TPM dyes as mediators are determined by the characteristics in the oxidation/reduction processes studied electrochemically. The reversibility of the oxidation/reduction processes was also established through the dependence of the voltammetric peaks with the sweep rates. All three dyes showed good performances compared to the FA and BQ when evaluated in a half enzymatic fuel cell. Potentiodynamic and power response experiments showed maxima power densities of 32.8 μW cm(-2) for ferrocene carboxy aldehyde followed by similar values obtained for TPM dyes around 30 μW cm(-2) using glucose and mediator concentrations of 10 mmol L(-1) and 1.0 mmol L(-1), respectively. Since no mediator consumption was observed during the bioelectrochemical process, and also good redox re-cycled processes were achieved, the use of triphenylmethane dyes is considered to be promising compared to other mediated systems used with glucose oxidase bioanodes and/or biofuel cells.     

Enzymatic biofuel cell based on anode and cathode powered by ethanol

Enzymatic biofuel cell based on enzyme modified anode and cathode electrodes are both powered by ethanol and operate at ambient temperature is described. The anode of the presented biofuel cell was based on immobilized quino-hemoprotein-alcohol dehydrogenase (QH-ADH), while the cathode on co-immobilized alcohol oxidase (AOx) and microperoxidase (MP-8). Two enzymes AOx and MP-8 acted in the consecutive mode and were applied in the design of the biofuel cell cathode. The ability of QH-ADH to transfer electrons directly towards the carbon-based electrode and the ability of MP-8 to accept electrons directly from the same type of electrodes was exploited in this biofuel cell design. Direct electron transfer (DET) to/from enzymes was the basis for generating an electric potential between the anode and cathode. Application of immobilized enzymes and the harvesting of the same type of fuel at both electrodes (cathode and anode) avoided the compartmentization of enzymatic biofuel cell. The maximal open circuit potential of the biofuel cell was 240mV.     

A sensitive capillary GC assay for the determination of sparteine oxidation products in microsomal fractions of human liver

A sensitive method for the assay of sparteine oxidase activity in vitro by microsomal fractions of human liver is described. The activity of sparteine oxidase was assessed by the formation of 2- and 5-dehydrosparteines, which were estimated by capillary gas chromatography with N2-FID detection. The limit of detection of the two metabolites, 2- and 5-dehydrosparteine, was 10 pmol (2.3 ng) per sample. Sparteine oxidase activity was linear with microsomal protein concentration ranging from 25 to 200 ug and with incubation times between 5 and 60 minutes. Omission of NADPH on incubation under an atmosphere of carbon monoxide inhibited formation of both metabolites, thus indicating that aforementioned metabolites arise in reaction catalyzed by cytochrome P-450. In three liver samples from humans classified as extensive (EM) metabolizers the formation of 2- and 5-dehydrosparteines was observed, 2-dehydrosparteine being the major metabolite. In these samples sparteine oxidase activity was characterised by Vmax = 136 +/- 53 pmol/min/mg and Km = 44 +/- 12 microM for 2-dehydrosparteine formation. For 5-dehydrosparteine formation the following values were obtained: Vmax = 57 +/- 18 pmol/min/mg and Km = 42 +/- 26 microM. In a liver sample from a poor metabolizer (PM) only the formation of 2-dehydrosparteine was detected with the method of analysis used. In this sample a great increase in Km (Km PM = 3033 microM) was noted, while Vmax was very similar to those obtained for 2-dehydrosparteine formation in EM subjects (Vmax PM = 147 pmol min/mg).     

Immobilization of flavoproteins on silicon: effect of cross-linker chain length on enzyme activity.

The effect of cross-linker chain length on the activities of choline oxidase (ChO) and glucose oxidase (GOx) immobilized on oxidized silicon wafers has been investigated for the cross-linkers N-succinimidyl 4-maleimido-butyrate (GMBS) and N-succinimidyl 6-maleimidocaproate (EMCS). Enzyme activities were determined with an indirect fluorometric assay based on the production of hydrogen peroxide. Immobilization of ChO or GOx onto oxidized silicon with either cross-linker resulted in an 86-99% loss in enzymatic activity relative to the soluble form of the flavoprotein. However, the different cross-linkers had distinctly different effects on enzyme activity: EMCS-immobilized GOx was four times more active than GMBS-immobilized GOx; EMCS-immobilized ChO had a sevenfold higher activity than GMBS-immobilized ChO.     

Enzyme-mediated hydrogel encapsulation of single cells for high-throughput screening and directed evolution of oxidoreductases

Directed evolution of oxidoreductases to improve their catalytic properties is being ardently pursued in the industrial, biotechnological, and biopharma sectors. Hampering this pursuit are current enzyme screening methods that are limited in terms of throughput, cost, time, and complexity. We present a directed evolution strategy that allows for large-scale one-pot screening of glucose oxidase (GOx) enzyme libraries in well-mixed homogeneous solution. We used GOx variants displayed on the outer cell wall of yeasts to initiate a cascade reaction with horseradish peroxidase (HRP), resulting in peroxidase-mediated phenol cross-coupling and encapsulation of individual cells in well-defined fluorescent alginate hydrogel shells within ~10 min in mixed cell suspensions. Following application of denaturing stress to whole-cell GOx libraries, only cells displaying GOx variants with enhanced stability or catalytic activity were able to carry out the hydrogel encapsulation reaction. Fluorescence-activated cell sorting was then used to isolate the enhanced variants. We characterized three of the newly evolved Aspergillus niger GOx enzyme sequences and found up to ~5-fold higher specific activity, enhanced thermal stability, and differentiable glycosylation patterns. By coupling intracellular gene expression with the rapid formation of an extracellular hydrogel capsule, our system improves high-throughput screening for directed evolution of H ₂O ₂-producing enzymes many folds.     

A mediated glucose/oxygen enzymatic fuel cell based on printed carbon inks containing aldose dehydrogenase and laccase as anode and cathode

Enzyme electrodes show great potential for many applications, as biosensors and more recently as anodes and cathodes in biocatalytic fuel cells for power generation. Enzymes have advantages over metal catalysts, as they provide high specificity and reaction rates, while operating under mild conditions. Here we report on studies related to development of mass-producible, completely enzymatic printed glucose/oxygen biofuel cells. The cells are based on filter paper coated with conducting carbon inks containing mediators and laccase, for reduction of oxygen, or aldose dehydrogenase, for oxidation of glucose. Mediator performance in these printed formats is compared to relative rate constants for the enzyme-mediator reaction in solution, for a range of anode and cathode mediators. The power output and stability of fuels cells using an acidophilic laccase isolated from Trametes hirsuta is greater, at pH 5, than that for cells based on Melanocarpus albomyces laccase, that shows optimal activity closer to neutral pH, at pH 6. Highest power output, although of limited stability, was observed for ThL/ABTS cathodes, providing a maximum power density of 3.5 μWcm(-2) at 0.34 V, when coupled to an ALDH glucose anode mediated by an osmium complex. The stability of cell voltage above a threshold of 200 mV under a moderate 75 kΩ load is used to benchmark printed fuel cell performance. Highest stability was obtained for a printed fuel cell using osmium complexes as mediators of glucose oxidation by aldose dehydrogenase, and oxygen reduction by T. hirsuta laccase, maintaining cell voltage above 200 mV for 137 h at pH 5. These results provide promising directions for further development of mass-producible, completely enzymatic, printed biofuel cells.     

Enzymatic fuel cells: integrating flow-through anode and air-breathing cathode into a membrane-less biofuel cell design

One of the key goals of enzymatic biofuel cells research has been the development of a fully enzymatic biofuel cell that operates under a continuous flow-through regime. Here, we present our work on achieving this task. Two NAD(+)-dependent dehydrogenase enzymes; malate dehydrogenase (MDH) and alcohol dehydrogenase (ADH) were independently coupled with poly-methylene green (poly-MG) catalyst for biofuel cell anode fabrication. A fungal laccase that catalyzes oxygen reduction via direct electron transfer (DET) was used as an air-breathing cathode. This completes a fully enzymatic biofuel cell that operates in a flow-through mode of fuel supply polarized against an air-breathing bio-cathode. The combined, enzymatic, MDH-laccase biofuel cell operated with an open circuit voltage (OCV) of 0.584 V, whereas the ADH-laccase biofuel cell sustained an OCV of 0.618 V. Maximum volumetric power densities approaching 20 μW cm(-3) are reported, and characterization criteria that will aid in future optimization are discussed.     

Ultrasonic processing of enzymes: Effect on enzymatic activity of glucose oxidase

The effect of ultrasonication on the enzymatic stability, conformation, and catalytic activity of the important oxidoreductase, glucose oxidase (GOx), was investigated. Thus, buffer-free aqueous solutions of GOx were ultrasonicated (23 kHz at 4 °C) for different periods of time (10, 30, and 60 min) and studied in terms of their enzymatic activity. The ultrasonicated GOx was also studied by UV/vis and circular dichroism (CD) spectroscopy and by thermogravimetric analysis, and compared with pristine GOx. The CD spectra of ultrasonicated GOx showed a different composition with reduced α-helix and β-sheet fractions upon extended sonication compared with the pristine GOx. Along with the changes of the secondary structure, the enzymatic activity measured via HRP-coupled bioassay of the sonicated GOx showed a small corresponding decrease. Low temperature ultrasonic processing of GOx does not appreciably compromise bioactivity.     

Direct electron transfer of glucose oxidase promoted by carbon nanotubes

A stable suspension of carbon nanotubes (CNT) was obtained by dispersing the CNT in a solution of surfactant, such as cetyltrimethylammonium bromide (CTAB, a cationic surfactant). CNT (dispersed in the solution of 0.1% CTAB) has promotion effects on the direct electron transfer of glucose oxidase (GOx), which was immobilized onto the surface of CNT. The direct electron transfer rate of GOx was greatly enhanced after it was immobilized onto the surface of CNT. Cyclic voltammetric results showed a pair of well-defined redox peaks, which corresponded to the direct electron transfer of GOx, with a midpoint potential of about -0.466 V (vs SCE (saturated calomel electrode)) in the phosphate buffer solution (PBS, pH 6.9). The electrochemical parameters such as apparent heterogeneous electron transfer rate constant (ks) and the value of midpoint potential (E1/2) were estimated. The dependence of E1/2 on solution pH indicated that the direct electron transfer reaction of GOx is a two-electron-transfer coupled with a two-proton-transfer reaction process. The experimental results also demonstrated that the immobilized GOx retained its bioelectrocatalytic activity for the oxidation of glucose, suggesting that the electrode may find use in biosensors (for example, it may be used as a bioanode in biofuel cells). The method presented here can be easily extended to immobilize and obtain the direct electrochemistry of other redox enzymes or proteins.