Mechanical properties of compacted morselized cancellous bone graft using one-dimensional consolidation testing

Failures of orthopaedic procedures that use morselized cancellous bone (MCB) graft for load bearing are often due to gross displacement within the graft material. For this reason the mechanical behavior of MCB must be better understood. Our purpose is to present a detailed testing methodology for the mechanical characterization of MCB, and to illustrate how this methodology can be used to study the influence of water and fat content. Complete one-dimensional consolidation testing was performed on bovine cancellous bone processed to represent MCB typically used in surgery (52% water, 31% fat). The one-dimensional consolidation strain under a stress of 1.09 MPa was 30.9% and the confined modulus was 8.0 MPa. The coefficient of consolidation (rate of consolidation) was 2.2×10⁻⁵ cm²/s and the coefficient of secondary strain (steady-state creep rate) was 1.9%. While reducing the water content alone had some influence on properties, reducing the fat content improved both the static and dynamic behavior. A sample of MCB which had fat intentionally minimized and a lower overall moisture content (56% water, 5% fat) demonstrated 23.1% strain, a confined modulus of 9.6 MPa, a coefficient of consolidation of 3.4×10⁻³ cm²/s, and a coefficient of secondary strain of 0.9%. The test methods described in this technical note can be used to evaluate the influence of fluid content on the mechanical behavior of MCB.     

The elastic properties of morsellised cortico-cancellous bone graft are dependent on its prior loading

Confined compression experiments were carried out on cortico-cancellous bone taken from bovine femoral condyles to assess the effect of prior loading on the elastic confined modulus, E(c) of morsellised cortico-cancellous bone (MCB). Measurements were taken to find the values of E(c) for MCB subjected to cyclic loading resulting in axial stresses in the range of 0.5-3.0 N mm(2). Two values of E(c) were considered: E(ic), the instantaneous modulus, and E(dc), the delayed modulus allowing for stress relaxation effects. It was found that the values of E(c) increased with increasing maximum axial stress. It was also found that for each stress level the values of E(c) increased as the number of load cycles increased. The dependence of E(c) on the maximum axial stress and the number of load cycles is seen to explain the wide range of values for the apparent modulus of MCB found in previous studies. Tests examining the stress relaxation behaviour of MCB are also discussed. The results indicate that a minimum of 10 compaction episodes are required for MCB to achieve around 90% of its predicted maximum stiffness for a given compaction force.     

Segmental bone replacement via patient‐specific,three‐dimensional printed bioresorbable graft substitutes and their use as templates for the culture of mesenchymal stem cells under mechanical stimulation at various frequencies

The treatment of large segmental bone defects remains a challenge as infection, delayed union, and nonunion are common postoperative complications. A three‐dimensional printed bioresorbable and physiologically load‐sustaining graft substitute was developed to mimic native bone tissue for segmental bone repair. Fabricated from polylactic acid, this graft substitute is novel as it is readily customizable to accommodate the particular size and location of the segmental bone of the patient to be replaced. Inspired by the structure of the native bone tissue, the graft substitute exhibits a gradient in porosity and pore size in the radial direction and exhibit mechanical properties similar to those of the native bone tissue. The graft substitute can serve as a template for tissue constructs via seeding with stem cells. The biocompatibility of such templates was tested under in vitro conditions using a dynamic culture of human mesenchymal stem cells. The effects of the mechanical loading of cell‐seeded templates under in vitro conditions were assessed via subjecting the tissue constructs to 28 days of daily mechanical stimulation. The frequency of loading was found to have a significant effect on the rate of mineralization, as the alkaline phosphatase activity and calcium deposition were determined to be particularly high at the typical walking frequency of 2 Hz, suggesting that mechanical stimulation plays a significant role in facilitating the healing process of bone defects. Utilization of such patient‐specific and biocompatible graft substitutes, coupled with patient’s bone marrow cells seeded and exposed to mechanical stimulation of 2 Hz have the potential of reducing significant volumes of cadaveric tissue required, improving long‐term graft stability and incorporation, and alleviating financial burdens associated with delayed or failed fusions of long bone defects.     

Impacted morselized cancellous bone: mechanical effects of defatting and augmentation with fine hydroxyapatite particles

Geotechnical engineering testing techniques were used to study the mechanical properties of morselized cancellous bone (MCB) and the effects of defatting and augmentation with fine hydroxyapatite (HA) particles. Bovine and human cancellous bone was morselized, rinsed, and manually squeezed to remove excess fluid, producing a standard surgical MCB sample that was also used as a control. Some of the MCB was defatted with heat and detergent and mixed with HA particles in ratios ranging from 0% to 100% HA. Compaction tests were used to determine the effects of moisture content and the amount of MCB that can be packed into a confined space. One-dimensional consolidation tests were used to determine the uniaxial strain behavior, confined modulus, and steady-state creep rate. The compaction tests demonstrated that defatting and adding HA particles significantly increased density. The one-dimensional consolidation tests showed that strain was decreased, modulus was increased and the creep rate was decreased by defatting and adding HA.     

Long-term serotonin administration leads to higher bone mineral density, affects bone architecture, and leads to higher femoral bone stiffness in rats

New evidence suggests a control of bone mass by the central nervous system. We have previously shown that functional serotonin receptors are present in bone cells and that serotonin stimulates proliferation of osteoblast precursor cells in vitro. In the present study we investigated the effects of serotonin on bone tissue in vivo. Ten, 2-month-old female Sprague-Dawley rats were injected with serotonin subcutaneously (s.c.) (5 mg/kg) once daily for 3 months, controls received saline. Using microdialysis and HPLC, free circulating serotonin levels were measured. DXA scans were made after 3 months of serotonin administration. Bone architecture and mechanical properties were investigated by micro-computed tomography (microCT), histomorphometry, and mechanical testing. A long-lasting hyperserotoninemia with a >10-fold increase in serotonin appeared. Total body BMD was significantly higher (0.1976+/-0.0015 vs. 0.1913+/-0.0012 g/cm2) in rats receiving serotonin. Cortical thickness (Ct.Th) measured by microCT analysis was also higher, whereas trabecular bone volume (BV) was lower. Interestingly, the perimeter and cross-sectional moment of inertia (MOI), a proxy for geometrical bone strength, were the same in both groups. These data suggest that serotonin reduces resorption or/and increases apposition of endosteal bone. Mechanical testing showed that femoral stiffness was higher in serotonin-dosed animals. The energy absorption also seemed slightly, but not significantly higher. In conclusion, hyperserotoninemia led to a higher BMD, altered bone architecture and higher femural bone stiffness in growing rats, demonstrating that serotonin may have important effects on bone in vivo.     

Heterogeneity of the mechanical properties of demineralized bone

Knowledge of the mechanical properties of the collagenous component of bone is required for composite modeling of bone tissue and for understanding the age- and disease-related reductions in the ductility and strength of bone. The overall goal of this study was to investigate the heterogeneity of the mechanical properties of demineralized bone which remains unexplained and may be due to differences in the collagen structure or organization or in experimental protocols. Uniaxial tension tests were conducted to measure the elastic and failure properties of demineralized human femoral (n = 10) and tibial (n = 13) and bovine humeral (n = 8) and tibial (n = 8) cortical bone. Elastic modulus differed between groups (p = 0.02), varying from 275 +/- 94 MPa (mean +/- SD) to 450 + 50 MPa. Similarly, ultimate stress varied across groups from 15 + 4.2 to 26 + 4.7 MPa (p = 0.03). No significant differences in strain-to-failure were observed between any groups in this study (pooled mean of 8.4 +/- 1.6%; p = 0.42). However, Bowman et al. (1996) reported an average ultimate strain of 12.3 +/- 0.5% for demineralized bovine humeral bone, nearly 40% higher than our value. Taken together, it follows that all the monotonic mechanical properties of demineralized bone can display substantial heterogeneity. Future studies directed at explaining such differences may therefore provide insight into aging and disease of bone tissue.     

Leptin predicts bone and fat mass after accounting for the effects of diet and glucocorticoid treatment in piglets

The role of leptin in neonatal growth and bone metabolism has been investigated, but not simultaneously. The objectives of this study were to determine if leptin relates to bone mass during rapid growth; if consumption of maternal milk is related to elevated circulating concentrations of leptin resulting in higher fat mass; and if glucocorticoids result in higher fat mass and reduced bone mass due to elevated leptin. Thirty-two piglets were randomized to either a suckling or milk substitute plus either dexamethasone (DEX) or placebo injection for 15 days beginning at 5 days of age. Milk and blood samples were obtained at baseline, and after 15 days, blood was sampled again for measurement of leptin and bone biochemistry. Weight at baseline plus weight and length after 15 days were recorded, followed by measurement of whole body bone mineral content, bone area, and fat mass using dual energy x-ray absorptiometry. At baseline, plasma leptin was elevated in suckled piglets. Piglets that suckled had elevated fat mass as did those who received DEX. However, DEX resulted in suppressed weight and length, bone mass, and bone metabolism. Leptin was similar among groups after the 15 days. After accounting for body size and treatment effects, piglet plasma leptin was predictive of bone and fat mass. Leptin circulating early postnatally is linked to body composition, specifically fat and bone mass. Elevations in fat mass and reductions in bone mass observed after 15 days of DEX treatment are not related to leptin metabolism. Both human and porcine neonates share similar characteristics with respect to relationships of leptin with fat and bone mass.     

Association of a synthetic bone graft and bone marrow cells as a composite biomaterial

Porous calcium phosphates have osteoconductive properties. The aim of this study was to obtain synthetic calcium phosphate bone graft substitute. X-ray diffraction was employed to investigate the formation of the beta-tricalcium phosphate (β-TCP) phase. We evaluated the effects of bone marrow on the osteoconductivity and mechanical properties of synthetic bone graft (SG). SG cylinders loaded with bone marrow (SGBM) and SG alone were implanted into rabbits femoral condyle bone defects. Histological examinations revealed the resorption of the SG, trabecular bone with osteoblasts and osteoid substance around the implants, and colonization inside the porous β-TCP by newly formed bone. Histomorphometry conducted after three months revealed the osteoid surface to be higher in SGBM than SG (p < 0.05). The compressive strengths of SG and SGBM were significantly higher than the anatomic control at all time periods. The elastic modulus of SBG and SGBM became weaker after implantation. The present results indicate that gB-TCP is a good matrix for bone marrow, which contributes osteoinductive properties in an orthotopic. The composite biomaterial may be useful in reconstructive bone surgery.     

The effect of chemical cleansing procedures combined with peracetic acid-ethanol sterilization on biomechanical properties of cortical bone.

Peracetic acid-ethanol sterilization (PES) with a preceding delipidation step is an effective sterilization method for allograft bone, but its influence on biomechanical properties of bone has not been studied. The aim of this study was to evaluate the effects of different incubation times of water, hydrogen peroxide and alcohol cleansing procedures combined with PES on biomechanical properties of freeze-dried cortical bone. These effects were studied by performing three-point bending tests on cortical samples. The lyophilized cortical samples were rehydrated prior to mechanical testing. The bending strength and the absorbed energy of the processed cortical samples were increased slightly but the Young's modulus was decreased compared to unprocessed samples. However, when the residual moisture content of the processed cortical samples was reduced from <5% to 0% all the biomechanical properties studied were significantly decreased. Hexane elution was used to determine the residual fat content of the processed cortical bone. Reducing the incubation time in cleansing had no effect on the residual fat content of the bone samples. Our in vitro study indicates that the cleansing procedure proposed combined with PES affects the biomechanical properties of cortical bone only on a limited scale.     

In vitro cytotoxicity of a novel injectable and biodegradable alveolar bone substitute

The unsaturated polyphosphoester (UPPE) polymer is being investigated as an injectable and biodegradable system for alveolar bone repair in the treatment of periodontal diseases. The incorporation of β-tricalcium phosphate (β-TCP) particles into the UPPE polymer was previously shown to significantly increase the material’s mechanical properties. Moreover, in vitro experiments demonstrated that the UPPE/β-TCP composite was capable of zero-order release of tetracycline for over 2 weeks. In this study, we investigated the in vitro cytotoxicity of each individual component, the resulting cross-linked network and the degradation products of the UPPE/β-TCP composite using an AlamarBlue viability assay. We confirmed that each individual component except β-TCP and the in vitro degradation products of the composite displayed a dose-dependent cytotoxic response. Once cross-linked, however, the composite did not demonstrate an adverse response. Our results suggest that the UPPE/β-TCP composite holds great promise for use as an injectable and biodegradable alveolar bone substitute.     

Development of a novel method for the strengthening and toughening of irradiation-sterilized bone allografts

Reconstruction of large skeletal defects is a significant and challenging issue. Bone allografts are often used for such reconstructions. However, sterilizing bone allografts by using γ-irradiation, damages collagen and causes the bone to become weak, brittle and less fatigue resistant. In a previous study, we successfully protected the mechanical properties of human cortical bone by conducting a pre-treatment with ribose, a natural and biocompatible agent. This study focuses on examining possible mechanisms by which ribose might protect the bone. We examined the mechanical properties, crosslinking, connectivity and free radical scavenging potentials of the ribose treatment. Human cortical bone beams were treated with varying concentration of ribose (0.06–1.2 M) and γ-irradiation before testing them in 3-point bending. The connectivity and amounts of crosslinking were determined with Hydrothermal-Isometric-Tension testing and High-Performance-Liquid-Chromatography, respectively. The free radical content was measured using Electron Paramagnetic Resonance. Ribose pre-treatment improved the mechanical properties of irradiation sterilized human bone in a pre-treatment concentration-dependent manner. The 1.2 M pre-treatment provided >100% of ultimate strength of normal controls and protected 76% of the work-to-fracture (toughness) lost in the irradiated controls. Similarly, the ribose pre-treatment improved the thermo-mechanical properties of irradiation-sterilized human bone collagen in a concentration-dependent manner. Greater free radical content and pentosidine content were modified in the ribose treated bone. This study shows that the mechanical properties of irradiation-sterilized cortical bone allografts can be protected by incubating the bone in a ribose solution prior to irradiation.     

Shear strength and toughness of trabecular bone are more sensitive to density than damage

Microdamage occurs in trabecular bone under normal loading, which impairs the mechanical properties. Architectural degradation associated with osteoporosis increases damage susceptibility, resulting in a cumulative negative effect on the mechanical properties. Treatments for osteoporosis could be targeted toward increased bone mineral density, improved architecture, or repair and prevention of microdamage. Delineating the relative roles of damage and architectural degradation on trabecular bone strength will provide insight into the most beneficial targets. In this study, damage was induced in bovine trabecular bone samples by axial compression, and the effects on the mechanical properties in shear were assessed. The damaged shear modulus, shear yield stress, ultimate shear stress, and energy to failure all depended on induced damage and decreased as the architecture became more rod-like. The changes in ultimate shear strength and toughness were proportional to the decrease in shear modulus, consistent with an effective decrease in the cross-section of trabeculae based on cellular solid analysis. For typical ranges of bone volume fraction in human bone, the strength and toughness were much more sensitive to decreased volume fraction than to induced mechanical damage. While ultimately repairing or avoiding damage to the bone structure and increasing bone density both improve mechanical properties, increasing bone density is the more important contributor to bone strength.     

Piezo1 opposes age-associated cortical bone loss

As we age, our bones undergo a process of loss, often accompanied by muscle weakness and reduced physical activity. This is exacerbated by decreased responsiveness to mechanical stimulation in aged skeleton, leading to the hypothesis that decreased mechanical stimulation plays an important role in age-related bone loss. Piezo1, a mechanosensitive ion channel, is critical for bone homeostasis and mechanotransduction. Here, we observed a decrease in Piezo1 expression with age in both murine and human cortical bone. Furthermore, loss of Piezo1 in osteoblasts and osteocytes resulted in an increase in age-associated cortical bone loss compared to control mice. The loss of cortical bone was due to an expansion of the endosteal perimeter resulting from increased endocortical resorption. In addition, expression of Tnfrsf11b, encoding anti-osteoclastogenic protein OPG, decreases with Piezo1 in vitro and in vivo in bone cells, suggesting that Piezo1 suppresses osteoclast formation by promoting Tnfrsf11b expression. Our results highlight the importance of Piezo1-mediated mechanical signaling in protecting against age-associated cortical bone loss by inhibiting bone resorption in mice.     

Apparent Young's modulus of vertebral cortico-cancellous bone specimens

Up to now, due to cortical thickness and imaging resolution, it is not possible to derive subject-specific mechanical properties on the 'vertebral shell' from imaging modalities applicable in vivo. As a first step, the goal of this study was to assess the apparent Young's modulus of vertebral cortico-cancellous bone specimens using an inverse method. A total of 22 cortico-cancellous specimens were harvested from 22 vertebral bodies. All specimens were tested in compression until failure. To compute the apparent Young's modulus of the specimen from the inverse method, the boundary conditions of the biomechanical experiments were faithfully reproduced in a finite element model (FEM), and an optimisation routine was used. The results showed a mean of the apparent Young's modulus of 374?±?208?MPa, ranging from 87 to 791?MPa. By computing an apparent Young's modulus of a cortico-cancellous medium, this study gives mechanical data for an FEM of an entire vertebra including an external shell combining both bone tissues.     

A 3D damage model for trabecular bone based on fabric tensors

Motivated by the role of damage in normal and pathological conditions of trabecular bone, a novel 3D constitutive law was developed that describes anisotropic elasticity and the rate-independent degradation in mechanical properties resulting from the growth of cracks or voids in the trabecular tissue. The theoretical model was formulated within the framework of continuum damage mechanics and based on two fabric tensors characterizing the local trabecular morphology. Experimental validation of the model was achieved by uniaxial and torsional testing of waisted bovine trabecular bone specimens. Strong correlations were found between cumulated permanent strain, reduction in elastic moduli and nonlinear postyield stress which support the hypothesis that these variables reflect the same underlying damage process.     

Playing with bone and fat

The relationship between bone and fat formation within the bone marrow microenvironment is complex and remains an area of active investigation. Classical in vitro and in vivo studies strongly support an inverse relationship between the commitment of bone marrow-derived mesenchymal stem cells or stromal cells to the adipocyte and osteoblast lineage pathways. In this review, we focus on the recent literature exploring the mechanisms underlying these differentiation events and discuss their implications relevant to osteoporosis and regenerative medicine.     

Bio-composites composed of a solid free-form fabricated polycaprolactone and alginate-releasing bone morphogenic protein and bone formation peptide for bone tissue regeneration

Biomedical scaffolds should be designed with highly porous three-dimensional (3D) structures that have mechanical properties similar to the replaced tissue, biocompatible properties, and biodegradability. Here, we propose a new composite composed of solid free-form fabricated polycaprolactone (PCL), bone morphogenic protein (BMP-2) or bone formation peptide (BFP-1), and alginate for bone tissue regeneration. In this study, PCL was used as a mechanical supporting component to enhance the mechanical properties of the final biocomposite and alginate was used as the deterring material to control the release of BMP-2 and BFP-1. A release test revealed that alginate can act as a good release control material. The in vitro biocompatibilities of the composites were examined using osteoblast-like cells (MG63) and the alkaline phosphatase (ALP) activity and calcium deposition were assessed. The in vitro test results revealed that PCL/BFP-1/Alginate had significantly higher ALP activity and calcium deposition than the PCL/BMP-2/Alginate composite. Based on these findings, release-controlled BFP-1 could be a good growth factor for enhancement of bone tissue growth and the simple-alginate coating method will be a useful tool for fabrication of highly functional biomaterials through release–control supplementation.     

Release of intact and fragmented osteocalcin molecules from bone matrix during bone resorption in vitro

Osteocalcin detected from serum samples is considered a specific marker of osteoblast activity and bone formation rate. However, osteocalcin embedded in bone matrix must also be released during bone resorption. To understand the contribution of each type of bone cell in circulating osteocalcin levels, we used immunoassays detecting different molecular forms of osteocalcin to monitor bone resorption in vitro. Osteoclasts were obtained from rat long bones and cultured on bovine bone slices using osteocalcin-depleted fetal bovine serum. In addition, human osteoclasts differentiated from peripheral blood mononuclear cells were used. Both rat and human osteoclasts released osteocalcin from bovine bone into medium. The amount of osteocalcin increased in the presence of parathyroid hormone, a stimulator of resorption, and decreased in the presence of bafilomycin A1, an inhibitor of resorption. The amount of osteocalcin in the medium correlated with a well characterized marker of bone resorption, the C-terminal telopeptide of type I collagen (r > 0.9, p < 0.0001). The heterogeneity of released osteocalcin was determined using reverse phase high performance liquid chromatography, and several molecular forms of osteocalcin, including intact molecule, were identified in the culture medium. In conclusion, osteocalcin is released from the bone matrix during bone resorption as intact molecules and fragments. In addition to the conventional use as a marker of bone formation, osteocalcin can be used as a marker of bone resorption in vitro. Furthermore, bone matrix-derived osteocalcin may contribute to circulating osteocalcin levels, suggesting that serum osteocalcin should be considered as a marker of bone turnover rather than bone formation.     

Lactoferrin promotes bone growth

We have demonstrated bovine or human lactoferrin to be an anabolic factor in skeletal tissue. In vitro, lactoferrin stimulates the proliferation of bone forming cells, osteoblasts, and cartilage cells at physiological concentrations (above 0.1 microg/ml). The magnitude of this effect exceeds that observed in response to other skeletal growth factors such as IGF-1 and TGFbeta. DNA synthesis is also stimulated in a bone organ culture system likely reflecting the proliferation of cells of the osteoblast lineage. Lactoferrin is also a potent osteoblast survival factor. In TUNEL and DNA fragmentation assays, lactoferrin decreased apoptosis, induced by serum withdrawal, by up to 70%. In addition, lactoferrin has powerful effects on bone resorbing cells, osteoclasts, decreasing osteoclast development at concentrations > 1 microg/ml in a murine bone marrow culture system. However, lactoferrin did not alter bone resorption in calvarial organ culture, suggesting that it does not influence mature osteoclast function. In vivo, local injection of lactoferrin in adult mice resulted in increased calvarial bone growth, with significant increases in bone area and dynamic histomorphometric indices of bone formation after only 5 injections. Taken together, these data demonstrate that the naturally-occurring glycoprotein lactoferrin is anabolic to bone in vivo, an effect which is consequent upon its potent proliferative and anti-apoptotic actions in osteoblasts, and its ability to inhibit osteoclastogenesis. Lactoferrin may therefore have a physiological role in bone growth, and a potential therapeutic role in osteoporosis.