Anaerobic biodegradation of pentachlorophenol in a contaminated soil inoculated with a methanogenic consortium or with Desulfitobacterium frappieri strain PCP-1

Anaerobic biodegradation of pentachlorophenol (PCP) in a contaminated soil from a wood-treating industrial site was studied in soil slurry microcosms inoculated with a PCP-degrading methanogenic consortium. When the microcosms containing 10%–40% (w/v) soil were inoculated with the consortium, more than 90% of the PCP was removed in less than 30 days at 29 °C. Less-chlorinated phenols, mainly 3-chlorophenol were slowly degraded and accumulated in the cultures. Addition of glucose and sodium formate to the microcosms was not necessary, suggesting that the organic compounds in the soil can sustain the dechlorinating activity. Inoculation of Desulfitobacterium frappieri strain PCP-1 along with a 3-chlorophenol-degrading consortium in the microcosms also resulted in the rapid dechlorination of PCP and the slow degradation of 3-chlorophenol. Competitive polymerase chain reaction experiments showed that PCP-1 was present at the same level throughout the 21-day biotreatment. D. frappieri, strain PCP-1, inoculated into the soil microcosms, was able to remove PCP from soil containing up to 200 mg PCP/kg soil. However, reinoculation of the strain was necessary to achieve more than 95% PCP removal with a concentration of 300 mg and 500 mg PCP/kg soil. These results demonstrate that D. frappieri strain PCP-1 can be used effectively to dechlorinate PCP to 3-chlorophenol in contaminated soils. Received: 14 November 1997 / Received revision: 29 January 1998 / Accepted: 24 February 1998     

Biodegradation kinetics of monoterpenes in liquid and soil-slurry systems

Batch experiments were conducted to evaluate the biodegradation rates of limonene, α-pinene, γ-terpinene, terpinolene and α-terpineol at 23 °C under aerobic conditions. Biodegradation was demonstrated by the depletion of monoterpene mass, CO₂ production and a corresponding increase in biomass. Monoterpene degradation in liquid cultures devoid of soil followed Monod kinetics. The maximum specific growth rate (μ_max) was 0.02 h⁻¹ and 0.06 h⁻¹ and the half-velocity constant (K _s ) varied from 32 mg/l to 3 mg/l for the limonene and α-terpineol respectively. The recovery of monoterpenes by solvent extraction from autoclaved and azide-amended soil-slurry samples decreased over time and ranged from 69% to 73% for 120 h of incubation period. Although a significant fraction of monoterpene hydrocarbon could not be extracted, mineralization of these compounds in the soil-slurry systems took place, as shown by CO₂ production. The soil-normalized degradation rates for the hydrocarbon monoterpenes ranged from 0.6 μg g⁻¹ h⁻¹ to 2.1 μg g⁻¹ h⁻¹. A kinetic model – which combined monoterpene biodegradation in the liquid phase and net desorption – was developed and applied to data obtained from soil-slurry assays. Received: 10 September 1996 / Received revision: 16 December 1996 / Accepted: 10 January 1997     

Hydrogen production with high yield and high evolution rate by self-flocculated cells of Enterobacter aerogenes in a packed-bed reactor

Continuous hydrogen gas evolution by self-flocculated cells of Enterobacter aerogenes, a natural isolate HU-101 and its mutant AY-2, was performed in a packed-bed reactor under glucose-limiting conditions in a minimal medium. The flocs that formed during the continuous culture were retained even when the dilution rate was increased to 0.9 h⁻¹. The H₂ production rate increased linearly with increases in the dilution rate up to 0.67 h⁻¹, giving maximum H₂ production rates of 31 and 58 mmol l⁻¹ h⁻¹ in HU-101 and AY-2 respectively, at a dilution rate of more than 0.67 h⁻¹. The molar H₂ yield from glucose in AY-2 was maintained at about 1.1 at dilution rates between 0.08 h⁻¹ and 0.67 h⁻¹, but it decreased rapidly at dilution rates more than 0.8 h⁻¹. Received: 27 August 1997 / Received revision: 11 November 1997 / Accepted: 14 December 1997     

Actual and potential rates of hydrogen photoproduction by continuous culture of the purple non-sulphur bacterium Rhodobacter capsulatus

The influence of (NH₄)₂SO₄ concentration and dilution rate (D) on actual and potential H₂ photoproduction has been studied in ammonium-limited chemostat cultures of Rhodobacter capsulatus B10. The actual H₂ production in a photobioreactor was maximal (approx. 80 ml h⁻¹l⁻¹) at D = 0.06 h⁻¹ and 4 mM (NH₄)₂SO₄. However, it was lower than the potential H₂ evolution (calculated from hydrogen evolution rates in incubation vials), which amounted to 100–120 ml h⁻¹ l⁻¹ at D = 0.03–0.08 h⁻¹. Taking into account the fact that H₂ production in the photobioreactor under these conditions was not limited by light or lactate, another limiting (inhibiting) factor should be sought. One possibility is an inhibition of H₂ production by the H₂ accumulated in the gas phase. This is apparent from the non-linear kinetics of H₂ evolution in the vials or from its inhibition by the addition of H₂; initial rates were restored in both cases after the vials had been refilled with argon. The actual H₂ production in the photobioreactor at D = 0.06 h⁻¹ was shown to increase from approximately 80 ml h⁻¹ l⁻¹ to approximately 100 ml h⁻¹ l⁻¹ under an argon flow at 100 ml min⁻¹. Under maximal H₂ production rates in the photobioreactor, up to 30% of the lactate feedstock was utilised for H₂ production and 50% for biomass synthesis. Received: 22 April 1997 / Received revision: 14 July 1997 / Accepted: 27 July 1997     

Photolimitation and photoinhibition as factors determining optimal dilution rate to produce eicosapentaenoic acid from cultures of the microalga Isochrysis galbana

Eicosapentaenoic acid (EPA) productivity from continuous cultures of the marine microalga Isochrysis galbana was studied, taking into account the irradiance on the reactor surface, that is, the photolimitation/photoinhibition regime to which the cells are exposed. Experiments were conducted under a wide variety of operating conditions. The dilution rate ranged from 0.005 h⁻¹ to 0.040 h⁻¹ at five external irradiances (820, 1620, 2050, 2450 and 3270 μmol photons m⁻² s⁻¹) covering photolimited to photoinhibited growth. Under these conditions, the specific growth rate (μ) was found to be the main factor influencing EPA content (ranging from 2.35% to 5.23% dryweight) and productivity (up to 0.88 mg l⁻¹ h⁻¹). The fatty acid content was not significantly affected by the external irradiance, but was influenced by the state of growth of the microalga, depending on whether the light regime was photolimiting or photoinhibiting. It might be suggested that light should no longer be considered an isolated factor affecting EPA synthesis, but an indirect influence through the photolimitation/photoinhibition regime and growth rate. At a given dilution rate, EPA content and biomass concentration are lower under photoinhibiting external irradiances than those corresponding to photolimiting conditions, and consequently EPA productivity decays. Since the effect of photoinhibition is less marked at high biomass concentration, a strategy to optimize EPA productivity from microalgal cultures could consist of reducing the dilution rate when the external irradiance increases above the phoinhibition threshold. Received: 16 January 1998 / Revised revision: 27 March 1998 / Accepted: 27 March 1998     

Determination of the kinetic parameters during continuous cultivation of the lipase-producing thermophile Bacillus sp. IHI-91 on olive oil

A thermostable lipase was produced in continuous cultivation of a newly isolated thermophilic Bacillus sp. strain IHI-91 growing optimally at 65 °C. Lipase activity decreased with increasing dilution rate while lipase productivity showed a maximum of 340 U l⁻¹ h⁻¹ at a dilution rate of 0.4 h⁻¹. Lipase productivity was increased by 50% compared to data from batch fermentations. Up to 70% of the total lipase activity measured was associated to cells and by-products or residual substrate. Kinetic and stoichiometric parameters for the utilisation of olive oil were determined. The maximal biomass output method led to a saturation constant K _S of 0.88 g/l. Both batch growth data and a washout experiment yielded a maximal specific growth rate, μ_max, of 1.0 h⁻¹. Oxygen uptake rates of up to 2.9 g l⁻¹h⁻¹ were calculated and the yield coefficient, Y _X/O, was determined to be 0.29 g dry cell weight/g O₂. From an overall material balance the yield coefficient, Y _X/S, was estimated to be 0.60 g dry cell weight/g olive oil. Received: 8 January 1997 / Received revision: 30 April 1997 / Accepted: 4 May 1997     

Ultrahigh-cell-density culture of a marine green alga Chlorococcum littorale in a flat-plate photobioreactor

To test the feasibility of CO₂ remediation by microalgal photosynthesis, a modified type of flat-plate photobioreactor [Hu et al. (1996) Biotechnol Bioeng 51:51–60] has been designed for cultivation of a high-CO₂-tolerant unicellular green alga Chlorococcum littorale. The modified reactor has a narrow light path in which intensive turbulent flow is provided by streaming compressed air through perforated tubing into the culture suspension. The length of the reactor light path was optimized for the productivity of biomass. The interrelationship between cell density and productivity, as affected by incident light intensity, was quantitatively assessed. Cellular ultrastructural and biochemical changes in response to ultrahigh cell density were investigated. The potential of biomass production under extremely high CO₂ concentrations was also evaluated. By growing C. littorale cells in this reactor, a CO₂ fixation rate of 16.7 g CO₂ l⁻¹ 24 h⁻¹ (or 200.4 g CO₂ m⁻² 24 h⁻¹) could readily be sustained at a light intensity of 2000 μmol m⁻² s⁻¹ at 25 °C, and an ultrahigh cell density of well over 80 g l⁻¹ could be maintained by daily replacing the culture medium. Received: 20 October 1997 / Received revision: 19 December 1997 / Accepted: 24 January 1998     

The production of xylitol from d-xylose by fermentation with Hansenula polymorpha

We have analysed the influence of the initial pH of the medium and the quantity of aeration provided during the batch fermentation of solutions of d-xylose by the yeast Hansenula polymorpha (34438 ATCC). The initial pH was altered between 3.5 and 6.5 whilst aeration varied between 0.0 and 0.3 vvm. The temperature was kept at 30 °C during all the experiments. Hansenula polymorpha is known to produce high quantities of xylitol and low quantities of ethanol. The most favourable conditions for the growth of xylitol turned out to be: an initial pH of between 4.5 and 5.5 and the aeration provided by the stirring vortex alone. Thus, at an initial pH of 5.5, the maximum specific production rate (μ_m) was 0.41 h⁻¹, the overall biomass yield (Y _x/s ^G) was 0.12 g g⁻¹, the specific d-xylose-consumption rate (q _s ) was 0.075 g g⁻¹ h⁻¹ (for t = 75 h), the specific xylitol-production rate (q _Xy ) was 0.31 g g⁻¹ h⁻¹ (for t = 30 h) and the overall yields of ethanol (Y _E/s ^G) and xylitol (Y _Xy/s ^G) were 0.017 and 0.61 g g⁻¹ respectively. Both q _s and q _Xy decreased during the course of the experiments once the exponential growth phase had finished. Received: 26 March 1998 / Received revision: 30 June 1998 / Accepted: 2 July 1998     

Benzene/toluene/p-xylene degradation. Part II. Effect of substrate interactions and feeding strategies in toluene/benzene and toluene/p-xylene fermentations in a partitioning bioreactor

A two-phase aqueous/organic partitioning bioreactor scheme was used to degrade mixtures of toluene and benzene, and toluene and p-xylene, using simultaneous and sequential feeding strategies. The aqueous phase of the partitioning bioreactor contained Pseudomonas sp. ATCC 55595, an organism able to degrade benzene, toluene and p-xylene simultaneously. An industrial grade of oleyl alcohol served as the organic phase. In each experiment, the organic phase of the bioreactor was loaded with 10.15 g toluene, and either 2.0 g benzene or 2.1 g p-xylene. The resulting aqueous phase concentrations were 50 mg/l, 25 mg/l and 8 mg/l toluene, benzene and p-xylene respectively. The simultaneous fermentation of benzene and toluene consumed these compounds at volumetric rates of 0.024 g l⁻¹ h⁻¹ and 0.067 g l⁻¹ h⁻¹, respectively. The simultaneous fermentation of toluene and p-xylene consumed these xenobiotics at volumetric rates of 0.066 g l⁻¹ h⁻¹ and 0.018 g l⁻¹ h⁻¹, respectively. A sequential feeding strategy was employed in which toluene was added initially, but the benzene or p-xylene aliquot was added only after the cells had consumed half of the initial toluene concentration. This strategy was shown to improve overall degradation rates, and to reduce the stress on the microorganisms. In the sequential fermentation of benzene and toluene, the volumetric degradation rates were 0.056 g l⁻¹ h⁻¹ and 0.079 g l⁻¹ h⁻¹, respectively. In the toluene/p-xylene sequential fermentation, the initial toluene load was consumed before the p-xylene aliquot was consumed. After 12 h in which no p-xylene degradation was observed, a 4.0-g toluene aliquot was added, and p-xylene degradation resumed. Excluding that 12-h period, the microbes consumed toluene and p-xylene at volumetric rates of 0.074 g l⁻¹ h⁻¹ and 0.025 g l⁻¹ h⁻¹, respectively. Oxygen limitation occurred in all fermentations during the rapid growth phase. Received: 16 November 1998 / Received revision: 29 March 1999 / Accepted: 9 April 1999     

The use of silica gel prepared by sol-gel method and polyurethane foam as microbial carriers in the continuous degradation of phenol

A mixed microbial culture was immobilized by entrapment into silica gel (SG) and entrapment/ adsorption on polyurethane foam (PU) and ceramic foam. The phenol degradation performance of the SG biocatalyst was studied in a packed-bed reactor (PBR), packed-bed reactor with ceramic foam (PBRC) and fluidized-bed reactor (FBR). In continuous experiments the maximum degradation rate of phenol (q _s ^max) decreased in the order: PBRC (598 mg l⁻¹h⁻¹) > PBR (PU, 471 mg l⁻¹h⁻¹) > PBR (SG, 394 mg l⁻¹h⁻¹) > FBR (PU, 161 mg l⁻¹h⁻¹) > FBR (SG, 91 mg l⁻¹ h⁻¹). The long-term use of the SG biocatalyst in continuous phenol degradation resulted in the formation of a 100–200 μm thick layer with a high cell density on the surface of the gel particles. The abrasion of the surface layer in the FBR contributed to the poor degradation performance of this reactor configuration. Coating the ceramic foam with a layer of cells immobilized in colloidal SiO₂ enhanced the phenol degradation efficiency during the first 3 days of the PBRC operation, in comparison with untreated ceramic packing. Received: 2 December 1999 / Revision received: 2 February 2000 / Accepted: 4 February 2000     

Pentachlorophenol biodegradation kinetics of an oligotrophic fluidized-bed enrichment culture

A fluidized-bed reactor (FBR) was used to enrich an aerobic chlorophenol-degrading microbial culture. Long-term continuous-flow operation with low effluent concentrations selected oligotrophic microorganisms producing good-quality effluent for pentachlorophenol(PCP)-contaminated water. PCP biodegradation kinetics was studied using this FBR enrichment culture. The results from FBR batch experiments were modeled using a modified Haldane equation, which resulted in the following kinetic constants: q _max = 0.41 mg PCP mg protein⁻¹ day⁻¹, K _S = 16 μg l⁻¹, K _i = 5.3 mg l⁻¹, and n = 3.5. These results show that the culture has a high affinity for PCP but is also inhibited by relatively low PCP concentrations (above 1.1 mg PCP l⁻¹). This enrichment culture was maintained over 1 year of continuous-flow operation with PCP as the sole source of carbon and energy. During continuous-flow operation, effluent concentrations below 2 μg l⁻¹ were achieved at 268 min hydraulic retention time (t _HR) and 2.5 mg PCP l⁻¹ feed concentration. An increase in loading rate by decreasing t _HR did not significantly deteriorate the effluent quality until a t _HR decrease from 30 min to 21 min resulted in process failure. Recovery from process failure was slow. Decreasing the feed PCP concentration and increasing t _HR resulted in an improved process recovery. Received: 10 October 1996 / Received revision: 21 January 1997 / Accepted: 24 January 1997     

Comparison of relative rates of BTEX biodegradation using respirometry

Biodegradation of BTEX by a microbial consortium isolated from a closed municipal landfill was studied using respirometric techniques. The kinetics of biodegradation were estimated from experimental oxygen uptake data using a nonlinear parameter estimation technique. All of the six compounds were rapidly degraded by the microbial culture and no substrate inhibition was observed at the concentration levels examined (200 mg L⁻¹ as COD). Microbial growth and contaminant degradation were adequately described by the Monod equation. Considerable differences were observed in the rates of BTEX biodegradation as seen from the estimates of the kinetic parameters. A three-fold variation was seen in the values of the maximum specific growth rate, μ_max. The highest value of μ_max was 0.389 h⁻¹ for p-xylene while o-xylene was characterized by a μ_max value of 0.14 h⁻¹, the lowest observed in this study. The half saturation coefficient, K _s, and the yield coefficient, Y, varied between 1.288–4.681 mg L⁻¹ and 0.272–0.645 mg mg⁻¹, respectively. Benzene and o-xylene exhibited higher resistance to biodegradation while toluene and p-xylene were rapidly degraded. Ethylbenzene and m-xylene were degraded at intermediate rates. In biodegradation experiments with a multiple substrate matrix, substrate depletion was slower than in single substrate experiments, suggesting an inhibitory nature of substrate interaction. Received 15 February 1998/ Accepted in revised form 5 July 1998     

The viability to a wall shear stress and propagation of <Emphasis Type="Italic">Bifidobacterium longum</Emphasis> in the intensive membrane bioreactor

Bifidobacterium longum grew at 65 L pilot scale of the membrane bioreactor (MBR), externally fitted with ceramic membrane (0.7 m²). Cell mass at the MBR reached 22.18 g L⁻¹ as dry cell weight in 12 h, which is 8.44 times higher than cell mass attained at the vial culture. The growth rate in the vial culture was μ = 0.385 h⁻ and at the batch culture was μ = 1.13 h⁻ in the exponential period and μ = 0.31 h⁻¹ in the stationary period. In the fed-batch mode was μ = 1.102 h⁻¹ for 6 h with inoculation and declined to μ = 0.456 h⁻¹ with feeding of feed medium. The growth rate at the MBR was μ = 0.134 h⁻¹. The number of viable cells was 6.01 × 10¹² cfu L⁻¹ at the batch culture, but increased to 1.15 × 10¹⁴ cfu L⁻¹ at the MBR culture. The specific growth rate of viable cell number (colony-forming units per liter, per hour) improved by 6.01 times from the batch to the MBR culture. The wall shear stress mainly generated by the pump, and the membrane incorporated into the MBR was controlled during the cultivation at the MBR. The viability of B. longum declined to under 10% in the first 2 weeks of the 4-week stability test (40°C) as B. longum was exposed to over wall shear stress 713 Pa, but the viability improved to 30–40% in wall shear stress of 260 Pa or STR culture. The loss in the cell viability can be saved by managing with wall shear stress during the cultivation at the MBR.     

Continuous cultures of <Emphasis Type="Italic">Pseudomonas putida</Emphasis> mt-2 overcome catabolic function loss under real case operating conditions

The long-term performance and stability of Pseudomonas putida mt-2 cultures, a toluene-sensitive strain harboring the genes responsible for toluene biodegradation in the archetypal plasmid pWW0, was investigated in a chemostat bioreactor functioning under real case operating conditions. The process was operated at a dilution rate of 0.1 h⁻¹ under toluene loading rates of 259 ± 23 and 801 ± 78 g m⁻³ h⁻¹ (inlet toluene concentrations of 3.5 and 10.9 g m⁻³, respectively). Despite the deleterious effects of toluene and its degradation intermediates, the phenotype of this sensitive P. putida culture rapidly recovered from a 95% Tol⁻ population at day 4 to approx. 100% Tol⁺ cells from day 13 onward, sustaining elimination capacities of 232 ± 10 g m⁻³ h⁻¹ at 3.5 g Tol m⁻³ and 377 ± 13 g m⁻³ h⁻¹ at 10.9 g Tol m⁻³, which were comparable to those achieved by highly tolerant strains such as P. putida DOT T1E and P. putida F1 under identical experimental conditions. Only one type of Tol⁻ variant, harboring a TOL-like plasmid with a 38.5 kb deletion (containing the upper and meta operons for toluene biodegradation), was identified.     

Continuous production of l(+)-lactic acid by Lactobacillus casei in two-stage systems

A two-stage two-stream chemostat system and a two-stage two-stream immobilized upflow packed-bed reactor system were used for the study of lactic acid production by Lactobacillus casei subsp casei. A mixing ratio of D ₁₂/D ₂= 0.5 (D = dilution rate) resulted in optimum production, making it possible to generate continuously a broth with high lactic acid concentration (48 g l⁻¹) and with a lowered overall content of initial yeast extract (5  g l⁻¹), half the concentration supplied in the one-step process. In the two-stage chemostat system, with the first stage at pH 5.5 and 37 °C and a second stage at pH 6.0, a temperature change from 40 °C to 45 °C in the second stage resulted in a 100% substrate consumption at an overall dilution rate of 0.05 h⁻¹. To increase the cell mass in the system, an adhesive strain of L. casei was used to inoculate two packed-bed reactors, which operated with two mixed feedstock streams at the optimal conditions found above. Lactic acid fermentation started after a lag period of cell growth over foam glass particles. No significant amount of free cells, compared with those adhering to the glass foam, was observed during continuous lactic acid production. The extreme values, 57.5 g l⁻¹ for lactic acid concentration and 9.72 g l⁻¹ h⁻¹ for the volumetric productivity, in upflow packed-bed reactors were higher than those obtained for free cells (48 g l⁻¹  and 2.42 g l⁻¹ h⁻¹) respectively and the highest overall l(+)-lactic acid purity (96.8%) was obtained in the two-chemostat system as compared with the immobilized-cell reactors (93%). Received: 4 December 1997 / Received revision: 23 February 1998 / Accepted: 14 March 1998     

Characterisation of a novel thermotolerant yeast, Kluyveromyces marxianus var marxianus: development of an ethanol fermentation process

The fermentation characteristics of the novel, thermotolerant, isolate Kluyveromyces marxianus var marxianus were determined to evaluate its aptitude for use in an ethanol production process. Sustainable growth was not observed under anaerobic conditions, even in the presence of unsaturated fatty acid and sterol. A maximum ethanol concentration of 40 g L⁻¹ was produced at 45°C, with an initial specific ethanol production rate of 1.7 g g⁻¹ h⁻¹. This was observed at ethanol concentrations below 8 g L⁻¹ and under oxygen-limited conditions. The low ethanol tolerance and low growth under oxygen-limited conditions required for ethanol production implied that a simple continuous process was not feasible with this yeast strain. Improved productivity was achieved through recycling biomass into the fermenter, indicating that utilising an effective cell retention method such as cell recycle or immobilisation, could lead to the development of a viable industrial process using this novel yeast strain. Received 14 February 1998/ Accepted in revised form 19 May 1998     

Repeated batch cultivation of the microalga Spirulina platensis

Summary The cultivation of photosynthetic microorganisms such as the microalga Spirulina platensis can provide an alternative source of food. The water in Mangueira Lagoon (Rio Grande do Sul state, southern Brazil) has several required nutrients for the growth of Spirulina and could be added to culture medium to reduce the cost of producing S. platensis. Although little studied, repeated batch cultivation is a very useful technique because it has a better cost–benefit ratio than other cultivation methods. In a series of runs, we studied the influence of cell concentration, renewal rate and strain on the specific growth rate and biomass productivity of S. platensis during repeated batch cultivation, the runs taking place in 2-l Erlenmeyer flasks for 2160 h at 30 °C and a light intensity of 2500 lux under a 12 h photoperiod. The three factors studied had a significant (P < 0.05) effect on the results (specific growth rate and productivity). Using Zarrouk’s medium, the highest specific growth rate (μ_X) was 0.111 day⁻¹ while the biomass productivity (P _X) was 0.0423 g l⁻¹ day⁻¹, while Mangueira Lagoon water supplemented with 10% Zarrouk’s medium gave μ_X = 0.113 day⁻¹ and a productivity P _X = 0.0467 g l⁻¹ day⁻¹. These values were two to three times higher than the results obtained in batch cultivation, indicating that the repeated batch cultivation of S. platensis is attractive and convenient.     

Simultaneous utilization of glucose and D-xylose by Candida shehatae in a chemostat

The kinetics of biomass formation, D-xylose utilization, and mixed substrate utilization were determined in a chemostat using the yeast Candida shehatae. The maximum growth rate of C. shehatae grown aerobically on D-xylose was 0.42 h⁻¹ and the Monod constant, K _s, was 0.06 g L⁻¹. The biomass yield, Y _{X/S}, ranged from 0.40 to 0.50 g g⁻¹ over a dilution rate range of 0.2–0.3 h⁻¹, when C. shehatae was grown on pure D-xylose. Mixtures of D-xylose and glucose (∼1 : 1) were simultaneously utilized over a dilution rate from 0.15 to 0.35 h⁻¹ at pH 3.5 and 4.5, but pH 3.5 reduced μ_max and reduced the dilution rate range over which D-xylose was utilized in the presence of glucose. At pH 4.5, μ_max was not reduced with the mixed sugar feed and the overall or lumped K _s value was not significantly increased (0.058 g L⁻¹ vs 0.06 g L⁻¹), when compared to a pure D-xylose feed. Kinetic data indicate that C. shehatae is an excellent candidate for chemostat production of value added products from renewable carbon sources, since simultaneous mixed substrate utilization was observed over a wide range of growth rates on a 1 : 1 mixture of glucose and D-xylose. Received 21 August 1997/ Accepted in revised form 28 May 1998     

Physiology and kinetics of trimethylamine conversion by two methylotrophic strains in continuous cultivation systems

The change of dilution rate (D) on both Methylophilus methylotrophus NCIMB11348 and Methylobacterium sp. RXM CCMI908 growing in trimethylamine (TMA) chemostat cultures was studied in order to assess their ability to remove odours in fish processing plants. M. methylotrophus NCIMB11348 was grown at dilution rates of 0.012–0.084 h⁻¹ and the biomass level slightly increased up to values of D around 0.07 h⁻¹. The maximum cell production rate was obtained at 0.07 h⁻¹ corresponding to a maximum conversion of carbon into cell mass (35%). The highest rate of TMA consumption was 3.04 mM h⁻¹ occurring at D=0.076 h⁻¹. Methylobacterium sp. RXM CCMI908 was grown under similar conditions. The biomass increased in a more steep manner up to values of D around 0.06 h⁻¹. The maximum cell production rate (0.058 g l⁻¹h⁻¹) was obtained in the region close to 0.06 h⁻¹ where a maximum conversion of the carbon into cell mass (40%) was observed. The maximum TMA consumption was 2.33 mM h⁻¹ at D=0.075 h⁻¹. The flux of carbon from TMA towards cell synthesis and carbon dioxide in both strains indicates that the cell is not excreting products but directing most of the carbon source to growth. Carbon recovery levels of approximately 100% show that the cultures are carbon-limited. Values for theoretical maximum yields and maintenance coefficients are presented along with a kinetic assessment based on the determination of the substrate saturation constant and maximum growth rate for each organism. Received: 25 February 1999 / Received revision: 14 May 1999 / Accepted: 17 May 1999     

Exchanges of oxygen, carbon dioxide, nitrogen and water in the caecilian Dermophis mexicanus

Oxygen consumption was measured in five Dermophis mexicanus and averaged (±SEM) 0.047 ± 0.004 ml O₂ g⁻¹ h⁻¹. Carbon dioxide production averaged 0.053 ± 0.005 ml CO₂ g⁻¹ h⁻¹ in the same five animals 1 week later. This metabolic rate is similar to metabolic rates of other Gymnophionans but lower than metabolic rates reported for Anurans and Urodeles. Total nitrogen excretion averaged 1.37 μmol N g⁻¹ h⁻¹ which is higher than that found for other amphibians. Of this, 82.5% (1.13 μmol N g⁻¹ h⁻¹) was in the form of urea while 17.5% (0.24 μmol N g⁻¹ h⁻¹) was in the form of NH₃ + NH⁺ ₄. Such ureotelism is typical of terrestrial amphibians like D. mexicanus. Osmotic water flux averaged 0.0193 ml g⁻¹ h⁻¹ in control (sham injected) animals and was not significantly altered by injection of either arginine vasotocin or mesotocin. This osmotic flux is similar to osmotic fluxes found for other terrestrial amphibians. The combined data suggest that metabolism in D. mexicanus is, like most other Gymnophionans, lower than other amphibians. The high rates of nitrogen (especially urea) excretion suggests that this fossorial animal accumulates urea like other burrowing amphibians. Accepted: 27 June 2000