Biosorption of Acid Black 172 and Congo Red from aqueous solution by nonviable Penicillium YW 01: Kinetic study, equilibrium isotherm and artificial neural network modeling

The main objective of this work was to investigate the biosorption performance of nonviable Penicillium YW 01 biomass for removal of Acid Black 172 metal-complex dye (AB) and Congo Red (CR) in solutions. Maximum biosorption capacities of 225.38 and 411.53 mg g⁻¹ under initial dye concentration of 800 mg L⁻¹, pH 3.0 and 40 °C conditions were observed for AB and CR, respectively. Biosorption data were successfully described with Langmuir isotherm and the pseudo-second-order kinetic model. The Weber-Morris model analysis indicated that intraparticle diffusion was the limiting step for biosorption of AB and CR onto biosorbent. Analysis based on the artificial neural network and genetic algorithms hybrid model indicated that initial dye concentration and temperature appeared to be the most influential parameters for biosorption process of AB and CR onto biosorbent, respectively. Characterization of the biosorbent and possible dye-biosorbent interaction were confirmed by Fourier transform infrared spectroscopy and scanning electron microscopy.     

Biosorption of acid violet dye from aqueous solutions using native biomass of a new isolate of Penicillium sp.

Laboratory investigation of the potential use of Penicillium sp. as biosorbent for the removal of acid violet dye from aqueous solution was studied with respect to pH, temperature, biosorbent, initial dye concentrations. Penicillium sp. decolourizes acid violet (30 mg l⁻¹) within 12 h agitation of 150 rpm at pH 5.7 and temperature of 35 °C. The pellets exhibited a high dye adsorption capacity (5.88 mg g⁻¹) for acid violet dye over a pH range (4–9); the maximum adsorption was obtained at pH 5.7. The increase of temperature favored biosorption for acid violet, but the optimum temperature was 35 °C. Adsorption kinetic data were tested using pseudo-first-order, pseudo-second-order and kinetic studies showed that the biosorption process follows pseudo-first-order rate kinetics with an average rate constant of 0.312 min⁻¹. Isotherm experiments were conducted to determine the sorbent–desorption behavior of examined dye from aqueous solutions using Langmuir and Freundlich equations. Langmuir parameter indicated a maximum adsorption capacity of 4.32 mg g⁻¹ for acid violet and R_L value of 0.377. Linear plot of log q_e vs log C_e shows that applicability of Freundlich adsorption isotherm model. These results suggest that this fungus can be used in biotreatment process as biosorbent for acid dyes.     

Nickel(II) biosorption by <Emphasis Type="Italic">Rhodotorula glutinis</Emphasis>

The present study reports the feasibility of using Rhodotorula glutinis biomass as an alternative low-cost biosorbent to remove Ni(II) ions from aqueous solutions. Acetone-pretreated R. glutinis cells showed higher Ni(II) biosorption capacity than untreated cells at pH values ranging from 3 to 7.5, with an optimum pH of 7.5. The effects of other relevant environmental parameters, such as initial Ni(II) concentration, shaking contact time and temperature, on Ni(II) biosorption onto acetone-pretreated R. glutinis were evaluated. Significant enhancement of Ni(II) biosorption capacity was observed by increasing initial metal concentration and temperature. Kinetic studies showed that the kinetic data were best described by a pseudo-second-order kinetic model. Among the two-, three-, and four-parameter isotherm models tested, the Fritz-Schluender model exhibited the best fit to experimental data. Thermodynamic parameters (activation energy, and changes in activation enthalpy, activation entropy, and free energy of activation) revealed that the biosorption of Ni(II) ions onto acetone-pretreated R. glutinis biomass is an endothermic and non-spontaneous process, involving chemical sorption with weak interactions between the biosorbent and Ni(II) ions. The high sorption capacity (44.45 mg g⁻¹ at 25°C, and 63.53 mg g⁻¹ at 70°C) exhibited by acetone-pretreated R. glutinis biomass places this biosorbent among the best adsorbents currently available for removal of Ni(II) ions from aqueous effluents.     

Biosorption of three textile dyes from contaminated water by filamentous green algal Spirogyra sp.: Kinetic,isotherm and thermodynamic studies

A freshwater filamentous green alga Spirogyra sp. was used as an inexpensive and efficient biosorbent for the removal of C.I. Acid Orange 7 (AO7), C.I. Basic Red 46 (BR46) and C.I. Basic Blue 3 (BB3) dyes from contaminated water. The effects of various physico–chemical parameters on dye removal efficiency were investigated, e.g. contact time, pH, initial dyes concentration, the amount of alga, temperature and biosorbent particle size. Dyes biosorption was a quick process and reactions reached to equilibrium conditions within 60 min. The biosorption capacity of three dyes onto alga was found in the following order: BR46 > BB3> AO7. The values of thermodynamic parameters, including ΔG, ΔH and ΔS, indicated that the biosorption of the dyes on the dried Spirogyra sp. biomass was feasible, spontaneous and endothermic. The pseudo-first order, pseudo-second order and the intraparticle diffusion models were applied to the experimental data in order to kinetically describe the removal mechanism of dyes, with the second one showing the best fit with the experimental kinetic biosorption data (R² = 0.99). It was also found that the adsorption process followed the Freundlich isotherm model with the highest value of correlation coefficients (0.99) and the biosorption capacity being estimated to be 13.2, 12.2 and 6.2 mg g⁻¹ for BR46, BB3 and AO7, respectively.     

Surfactant aided biodegradation of pyrene using immobilized cells of Mycobacterium frederiksbergense

Low aqueous phase solubility is the major limiting factor in successful biodegradation of pyrene and other polycyclic aromatic hydrocarbons (PAH), which can, however, be overcome by using a suitable surfactant. Biodegradation of pyrene by immobilized cells of Mycobacterium frederiksbergense in presence of non-ionic surfactant Tween 80 was evaluated. For cell immobilization, beads were prepared using calcium alginate as the immobilizing material based on immobilized cell viability and mechanical stability of the beads. Complete degradation of pyrene was achieved employing the immobilized cells in batch shake flask experiments for all four different initial concentrations of the PAH at 100 mg l⁻¹, 200 mg l⁻¹, 400 mg l⁻¹ and 1000 mg l⁻¹. The experimental results of biodegradation of pyrene at very high initial concentration of 1000 mg l⁻¹ using the cell immobilized beads was further investigated in a 3 l fermentor operated at controlled conditions of 150 rpm, 28 °C, pH 7 and 1.5 l min⁻¹ aeration. The results confirmed complete degradation of the PAH with a very higher degradation rate of 250 mg l⁻¹ d⁻¹, which is so far the highest value reported for pyrene biodegradation.     

Senna auriculata L. flower petal biomass: An alternative green biosorbent for the removal of fluoride from aqueous solutions

Fluoride contamination in groundwater is a major concern in many parts of India and all over the world. Researches paying attention for the removal of fluoride through the application of biosorbents prepared from different parts of plants are finding greater scope and importance. The present research work focuses on Senna auriculata L., flower petal biomass as biosorbent, and evaluated its feasibility for fluoride ion elimination from aqueous solutions. Batch experiments were conducted to remove fluoride under different experimental conditions have been optimized for the maximum removal of fluoride; 80% removal was observed at pH: 6, sorbent dosage: 0.25 g/100 mL, time of agitation: 90 min, and initial concentration of the fluoride ions: 5 mg/L. Characterization studies of the biosorbent revealed its favorability towards the sorption of fluoride. In the isothermal modeling studies, Langmuir isotherm model was obeyed by the biosorption process with R² value of 0.98 and from a kinetic perspective, the biosorption of fluoride onto the biosorbent observed the pseudo-second-order reaction with R² value of 0.98. The developed biosorbent has been applied to real field fluoride-contaminated water samples and found to be successful.     

Adsorptive removal of Pb(II) by activated carbon prepared from Spartina alterniflora: Equilibrium,kinetics and thermodynamics

Low-cost activated carbon was prepared from Spartina alterniflora by phosphoric acid activation for the removal of Pb(II) from dilute aqueous solution. The effect of experimental parameters such as pH, initial concentration, contact time and temperature on the adsorption was studied. The obtained data were fitted with the Langmuir and Freundlich equations to describe the equilibrium isotherms. The kinetic data were fitted with the Lagergren-first-order, pseudo-second-order and Elovich models. It was found that pH played a major role in the adsorption process. The maximum adsorption capacity for Pb(II) on S. alterniflora activated carbon (SAAC) calculated from Langmuir isotherm was more than 99 mg g⁻¹. The optimum pH range for the removal of Pb(II) was 4.8–5.6. The Freundlich isotherm model was found to best describe the experimental data. The kinetic rates were best fitted to the pseudo-second-order model. Thermodynamic study showed the adsorption was a spontaneous exothermic process.     

Biosorption of an Azo Dye by <Emphasis Type="Italic">Aspergillus niger</Emphasis> and <Emphasis Type="Italic">Trichoderma</Emphasis> sp. Fungal Biomasses

Biosorption is an eco-friendly and cost-effective method for treating the dye house effluents. Aspergillus niger and Trichoderma sp. were cultivated in bulk and biomasses used as biosorbents for the biosorption of an azo dye Orange G. Batch biosorption studies were performed for the removal of Orange G from aqueous solutions by varying the parameters like initial aqueous phase pH, biomass dosage, and initial dye concentration. It was found that the maximum biosorption was occurred at pH 2. Experimental data were analyzed by model equations such as Langmuir and Freundlich isotherms, and it was found that both the isotherm models best fitted the adsorption data. The monolayer saturation capacity was 0.48 mg/g for Aspergillus niger and 0.45 mg/g for Trichoderma sp. biomasses. The biosorption kinetic data were tested with pseudo first-order and pseudo second-order rate equations, and it was found that the pseudo second-order model fitted the data well for both the biomasses. The rate constant for the pseudo second-order model was found to be 10–0.8 (g/mg min⁻¹) for Aspergillus niger and 8–0.4 (g/mg min⁻¹) for Trichoderma sp. by varying the initial dye concentrations from 5 to 25 mg/l. It was found that the biomass obtained from Aspergillus niger was a better biosorbent for the biosorption of Orange G dye when compared to Trichoderma sp.     

A natural macroalgae consortium for biosorption of copper from aqueous solution: Optimization,modeling and design studies

In this study, the capacity of a natural macroalgae consortium consisting of Chaetomorpha sp., Polysiphonia sp., Ulva sp. and Cystoseira sp. species for the removal of copper ions from aqueous environment was investigated at different operating conditions, such as solution pH, copper ion concentration and contact time. These environmental parameters affecting the biosorption process were optimized on the basis of batch experiments. The experimentally obtained data for the biosorption of copper ions onto the macroalgae-based biosorbent were modeled using the isotherm models of Freundlich, Langmuir, Sips and Dubinin–Radushkevich and the kinetic models of pseudo-first-order, pseudo-second-order, Elovich and Weber and Morris. The pseudo-first-order and Sips equations were the most suitable models to describe the copper biosorption from aqueous solution. The thermodynamic data revealed the feasibility, spontaneity and physical nature of biosorption process. Based on the data of Sips isotherm model, the biosorption capacity of biosorbent for copper ions was calculated as 105.370 mg g^?1 under the optimum operating conditions. A single-stage batch biosorption system was developed to predict the real-scale-based copper removal performance of biosorbent. The results of this investigation showed the potential utility of macroalgae consortium for the biosorption of copper ions from aqueous medium.     

Biosorption of chromium(VI) by spent cyanobacterial biomass from a hydrogen fermentor using Box-Behnken model

The study explores utilization of waste cyanobacterial biomass of Nostoc linckia from a lab-scale hydrogen fermentor for the biosorption of Cr(VI) from aqueous solution. The biomass immobilized in alginate beads was used for removal of the metal in batch mode optimizing the process conditions adopting response surface methodology (RSM). Kinetic studies were done to get useful information on the rate of chromium adsorption onto the cyanobacterial biomass, which was found to follow pseudo second-order model. Four important process parameters including initial metal concentration (10-100 mg/L), pH (2-6), temperature (25-45 °C) and cyanobacterial dose (0.1-2.0 g) were optimized to obtain the best response of Cr(VI) removal using the statistical Box-Behnken design. The response surface data indicated maximum Cr(VI) biosorption at pH 2-4 with different initial concentrations of the metal in the aqueous solution. The biosorbent could remove 80-90% chromium from solutions with initial metal concentration of 10-55 mg/L. Involvement of the surface characteristics of the biomass was studied through its scanning electron micrographs and Fourier transform infrared (FTIR) analysis.     

Lead biosorption by different morphologies of fungus Mucor indicus

Biosorption characteristics of Pb⁺² ions from aqueous solution were investigated using fungus Mucor indicus biomass treated with NaOH. Biosorption was measured as a function of biomass morphology, pH, biomass concentration, contact time, and metal concentration. The morphology of M. indicus biomass was manipulated towards filamentous or yeast-like forms. The highest and lowest biosorption capacities were observed for purely filamentous and yeast-like forms, respectively. Models of Langmuir, Freundlich, Temkin, and Scachard were applied to describe adsorption isotherm and fitted appropriately. Biosorption kinetics was successfully described using Ho’s pseudo-second-order model. Maximum and minimum values of biosorption capacity of Pb²⁺ were 22.1 and 12.1 mg g⁻¹ for purely filamentous and yeast-like morphologies, respectively. Increasing pH resulted in higher biosorption of Pb⁺² ions up to pH 5.5. Biosorption capacity of individual Pb⁺² ions was reduced in the presence of other metal ions in bi- or multi-metal ion experiments. Metal ions adsorption by the biomass could be eluted effectively with HNO₃.     

Detoxification and accumulation of chromium from tannery effluent and spent chrome effluent by Paecilomyces lilacinus fungi

The tannery industry process involves chromium (Cr) salts as a main constituent of the process. The Cr recovery is a part of the process where other salts are used to achieve separation and recovery for using Cr back in the process. The process steps may contain both forms of Cr [Cr(VI): hexavalent and Cr(III): trivalent]. The recovery of Cr from tannery industry effluent through biological systems is much needed. The diverse physicochemical characteristics of these effluents may limit the growth of microorganisms and hence the limitation towards possible practical application of microorganisms in real industrial effluent conditions. The present study attempted the ability of the Cr-resistant fungus Paecilomyces lilacinus [isolated through an enrichment culture technique at 25 000 mg l⁻¹ of Cr(III)] to grow and remove Cr [Cr(VI) and Cr(III)] from two physicochemically different undiluted tannery industry effluents (tannery effluent and spent chrome effluent) in the presence of cane sugar as a carbon source. Such attempts are made keeping in view the potential integration of biological processes in the overall Cr removal and recovery processes to improve its efficiency and environmental sustainability. The fungus has broad pH tolerance range and can reduce Cr(VI) both in acidic (pH 5.5) and alkaline (pH 8.0) conditions. The fungus showed the ability to remove Cr(VI) (1.24 mg l⁻¹) and total Cr (7.91 mg l⁻¹) from tannery effluent below the detection level within 18 h and 36 h of incubation, respectively, and ability to accumulate 189.13 mg Cr g⁻¹ of dry biomass within 600 h of incubation from spent chrome effluent [containing 3731.4 mg l⁻¹ of initial Cr(III) concentration].At 200 mg l⁻¹ of Cr(VI) in growth media, with 100% detoxification and with only 10.54% of total Cr accumulation in the biomass, P. lilacinus showed Cr(VI) reduction as a major mechanism of Cr(VI) detoxification. The time-course study revealed the log phase of the growth for the maximum specific reduction of Cr(VI) and stationary phase of the growth for its maximum specific accumulation of both the forms of Cr [Cr(III) and Cr(VI)] in its biomass. In growth media at 50 mg l⁻¹ and 200 mg l⁻¹ of Cr(VI), P. lilacinus showed 100% reduction within 36 h and 120 h of incubation, respectively. The high degree of positive correlation and statistically high degree of relationship (r² = 0.941) between the fungal growth and % Cr(VI) reduction by the fungus support the role of metabolically active cellular growth in Cr(VI) reduction by the fungus. Results indicate that expanded solid (sludge) retention times (SRTs) (stationary phase) can be recommended for the removal of Cr(III) through accumulation. In case of Cr(VI), reduction needs a priority; therefore, a non-expanded SRT is recommended for designing a continuous-flow completely stirred bioreactor so that a log phase of cellular growth can be maintained during the reduction process. This study reveals the strong potential of P. lilacinus fungi for the removal of Cr from tannery effluent and spent chrome effluent.     

Nonlinear modelisation of heavy metal removal from aqueous solution using Ulva lactuca algae

After extensive analysis, Ulva lactuca dried algae, collected from the Monastir coastal zone, was proven to be successful as an adsorbent for the removal of certain inorganic pollutants. The main objective of this study was the nonlinear modeling of heavy metal removal from an aqueous solution, using a freely available and well analyzed biomaterial, as well as the evaluation of its efficacy on various metal ion sorptions. Although relatively low specific surface area, compared to more conventional adsorbents, the selected biomaterial displays very interesting retention capacities when used with aqueous inorganic pollutants. The pseudo, first and second-order kinetic models were used to investigate the kinetic retention mechanism. Assuming the nonlinear form, the results indicate that the retention mechanism is diffusion controlled. Concerning the heavy metal uptake capacity, it was found that the selected biomaterial has a retention capacity of 67 mg g⁻¹ of Ni(II), 112 mg g⁻¹ of Cu(II), 127 mg g⁻¹of Cd(II) and 230 mg g⁻¹ of Pb(II).     

Waste biomass of Nostoc linckia as adsorbent of crystal violet dye: Optimization based on statistical model

The potential of spent biomass of a hydrogen producing cyanobacterial strain Nostoc linckia from a hydrogen fermentor was studied for decolorization of a tri-phenylmethane dye, crystal violet. The waste cyanobacterial biomass immobilized in calcium alginate was used as a biosorbent and the process variables were optimized for maximum dye removal using the statistical response surface methodology (RSM). Batch mode experiments were performed to determine the kinetic behavior of the dye in aqueous solution allowing the computation of kinetic parameters. Influence of interacting parameters like temperature (25-35 °C), pH (4-8), initial dye concentration (100-200 mg/L) and cyanobacterial dose (0.2-0.4 g) on dye removal were examined using central composite design (CCD) which included two additional levels for each parameter. Second-order polynomial regression model, was applied which was statistically validated using analysis of variance. Ability of the immobilized biomass to decolorize the dye was maximum (72%) at pH 8.0, temperature 35 °C, 200 mg/L initial dye concentration and 0.2 g cyanobacterial dose. Adsorption of the dye on cell surface was further confirmed by scanning electron micrographs of the biomass before and after dye loading. FT-IR studies revealed that decolorization was due to biosorption mediated mainly by functional groups like hydroxyl, amide, carboxylate, methyl and methylene groups present on the cell surface.     

Biosorption of Nickel(II) from aqueous solution by the fungal mat of Trametes versicolor (rainbow) biomass: equilibrium, kinetics, and thermodynamic studies

This study investigates the equilibrium, kinetics and thermodynamics of Nickel(II) biosorption from aqueous solution by the fungal mat of Trametes versicolor (rainbow) biomass. The optimum biosorption conditions like pH, contact time, biomass dosage, initial metal ion concentration and temperaturewere determined in the batch method. The biosorbent was characterized by FTIR, SEM and BET surface area analysis. The experimental data were analyzed in terms of pseudo-first-order, pseudo-secondorder and intraparticle diffusion kinetic models, further it was observed that the biosorption process of Ni(II) ions closely followed pseudo-second-order kinetics. The equilibrium data of Ni(II) ions at 303, 313, and 323 K were fitted to the Langmuir and Freundlich isotherm models. Langmuir isotherm provided a better fit to the equilibrium data andthe maximum monolayer biosorption capacity of the T. versicolor(rainbow) biomass for Ni(II) was 212.5 mg/g at pH 4.0. The calculated thermodynamic parameters, ΔG^○, ΔH^○, and ΔS^○, demonstrated that the biosorption of Ni(II) ions onto the T. versicolor (rainbow) biomass was feasible, spontaneous and endothermic at 303 ～ 323 K. The performance of the proposed fungal biosorbent was also compared with that of many other reported sorbents for Nickel(II) removal and it was observed that the proposed biosorbent is effective in terms of its high sorption capacity.     

Biosorption of Basic Orange using dried A. filiculoides

In order to understand the biosorption of Basic Organic (BO) textile dye on dried Azolla filiculoides (A. filiculoides), batch experiments were conducted under various conditions. The results show that biosorption of BO on dried A. filiculoides was dependent on the initial solution pH, biosorbent dosage, contact time and the initial BO concentration. Using the Langmuir equation, the biosorption capacity (q_m) for BO was 833 mg/g at 303 K. The kinetic study suggested that the mechanism of biosorption was due to ion-exchange physisorption via the intra-particle diffusion and chemisorption on the external surface of dried A. filiculoides. Different techniques were used to characterize dried A. filiculoides and indicated that the biomass had a high cation exchange capacity (93.6 mmol/100 g), a large specific surface area (80.35–422.89 m²/g) and contained various functional groups which may play an important role in the physisorption and chemisorption of BO on the surface of A. filiculoides. The results showed that the removal ratio of BO reached 79.3% from wastewater containing 100 mg/L BO, indicating that the biomass could be used as a potential biosorbent for the removal of BO from industrial wastewater.     

Biosorption of Copper by Cyanobacterial Bloom-Derived Biomass Harvested from the Eutrophic Lake Dianchi in China

Biomass of cyanobacterial bloom from Lake Dianchi was used as a biosorbent for copper removal from aqueous solution. The maximum capacity was found at conditions of pH 4, initial concentration of copper was 10 mg/l and initial dose of biomass was 1.0 g/l. HNO₃ demonstrated the highest desorption efficiency compared with HCl, EDTA, and citric acid. Physical adsorption was assumed not to be the dominant mechanism of biosorption as revealed by scanning electron microscopy and surface area measurement of the biomass. Infrared ray spectra analysis of the biomass suggested that ion-exchange is the principal mechanism for biosorption. Considering the advantages—low cost, easy to collect, and huge in quantity—the Microcystis bloom biomass could be used as a sorbent for copper and other heavy metals removal.     

An ecofriendly approach for bioremediation of contaminated water environment: Potential contribution of a coastal seaweed community to environmental improvement

High levels of heavy metals like copper ions in many industrial based effluents lead to serious environmental and health problems. Biosorption is a potential environmental biotechnology approach for biotreatment of aquatic sites polluted with heavy metal ions. Seaweeds have received great attention for their high bioremediation potential in recent years. However, the co-application of marine macroalgae for removal of heavy metals from wastewater is very limited. Thus, for the first time in literature, a coastal seaweed community composed of Chaetomorpha sp., Polysiphonia sp., Ulva sp. and Cystoseira sp. species was applied to remove copper ions from synthetic aqueous medium in this study. The biosorption experiments in batch mode were conducted to examine the effects of operating variables including pH, biosorbent amount, metal ion concentration and contact time on the biosorption process. The biosorption behavior of biosorbent was described by various equilibrium, kinetic and thermodynamic models. The biosorption of copper ions was strongly influenced by the operating parameters. The results indicated that the equilibrium data of biosorption were best modeled by Sips isotherm model. The values of mean free energy of biosorption computed from Dubinin-Radushkevich isotherm model and the standard Gibbs free energy change indicated a feasible, spontaneous and physical biotreatment system. The pseudo-second-order rate equation successfully defined the kinetic behavior of copper biosorption. The pore diffusion also played role in the control of biosorption process. The maximum copper uptake capacity of biosorbent was found to be greater than those of many other biosorbents. The obtained results revealed that this novel biosorbent could be a promising material for copper ion bioremediation implementations.     

Biosorption characteristics of Aspergillus fumigatus for the decolorization of triphenylmethane dye acid violet 49

This study focuses on the possible use of Aspergillus fumigatus to remove acid violet 49 dye (AV49) from aqueous solution. In batch biosorption experiments, the highest biosorption efficiency was achieved at pH 3.0, with biosorbent dosage of 3.0 gL^?1 within about 30 min at 40 °C. The Langmuir and Freundlich models were able to describe the biosorption equilibrium of AV49 onto fungal biomass with maximum dye uptake capacity 136.98 mg g^?1. Biosorption followed a pseudo-second-order kinetic model with high correlation coefficients (R ²?>?0.99), and the biosorption rate constants increased with increasing temperature. Thermodynamic parameters indicated that the biosorption process was favorable, spontaneous, and endothermic in nature, with insignificant entropy changes. Fourier transform infrared spectroscopy strongly supported the presence of several functional groups responsible for dye–biosorbent interaction. Fungal biomass was regenerated with 0.1 M sodium hydroxide and could be reused a number of times without significant loss of biosorption activity. The effective decolorization of AV49 in simulated conditions indicated the potential use of biomass for the removal of color contaminants from wastewater.