Maximum removal rate of propionic acid as a sole carbon source in UASB reactors and the importance of the macro- and micro-nutrients stimulation

The maximum propionic acid (HPr) removal rate (R_HPr) was investigated in two lab-scale Upflow Anaerobic Sludge Bed (UASB) reactors. Two feeding strategies were applied by modifying the hydraulic retention time (HRT) in the UASB_HRT and the influent HPr concentration in the UASB_HPr, respectively. The experiment was divided into three main phases: phase 1, influent with only HPr; phase 2, HPr with macro-nutrients supplementation and phase 3, HPr with macro- and micro-nutrients supplementation. During phase 1, the maximum R_HPr achieved was less than 3 g HPr-COD L⁻¹ d⁻¹ in both reactors. However, the subsequent supplementation of macro- and micro-nutrients during phases 2 and 3 allowed to increase the R_HPr up to 18.1 and 32.8 g HPr-COD L⁻¹ d⁻¹, respectively, corresponding with an HRT of 0.5 h in the UASB_HRT and an influent HPr concentration of 10.5 g HPr-COD L⁻¹ in the UASB_HPr. Therefore, the high operational capacity of these reactor systems, specifically converting HPr with high throughput and high influent HPr level, was demonstrated. Moreover, the presence of macro- and micro-nutrients is clearly essential for stable and high HPr removal in anaerobic digestion.     

Ethanol production from syngas by Clostridium strain P11 using corn steep liquor as a nutrient replacement to yeast extract

The feasibility of replacing yeast extract (YE) by corn steep liquor (CSL), a low cost nutrient source, for syngas fermentation to produce ethanol using Clostridium strain P11 was investigated. About 32% more ethanol (1.7 g L⁻¹) was produced with 20 g L⁻¹ CSL media in 250-mL bottle fermentations compared to media with 1 g L⁻¹ YE after 360 h. Maximum ethanol concentrations after 360 h of fermentation in a 7.5-L fermentor with 10 and 20 g L⁻¹ CSL media were 8.6 and 9.6 g L⁻¹, respectively, which represent 57% and 60% of the theoretical ethanol yields from CO. Only about 6.1 g L⁻¹ of ethanol was obtained in the medium with 1 g L⁻¹ YE after 360 h, which represents 53% of the theoretical ethanol yield from CO. The use of CSL also enhanced butanol production by sevenfold compared to YE in bottle fermentations. These results demonstrate that CSL can replace YE as the primary medium component and significantly enhance ethanol production by Clostridium strain P11.     

Techno-economic implications of improved high gravity corn mash fermentation

The performance of Saccharomyces cerevisiae MBG3964, a strain able to tolerate >18% v/v ethanol, was compared to leading industrial ethanol strain, Fermentis Ethanol Red, under high gravity corn mash fermentation conditions. Compared to the industrial ethanol strain, MBG3964 gave increased alcohol yield (140 g L⁻¹ vs. 126 g L⁻¹), lower residual sugar (4 g L⁻¹ vs. 32 g L⁻¹), and lower glycerol (11 g L⁻¹ vs. 12 g L⁻¹). After 72 h fermentation, MBG3964 showed about 40% viability, whereas the control yeast was only about 3% viable. Based on modelling, the higher ethanol tolerant yeast could increase the profitability of a corn-ethanol plant and help it remain viable through higher production, lower unit heating requirements and extra throughput. A typical 50 M gal y⁻¹ dry mill ethanol plant that sells dried distiller’s grain could potentially increase its profit by nearly $US3.4 M y⁻¹ due solely to the extra yield, and potentially another $US4.1 M y⁻¹ if extra throughput is possible.     

Optimization of growth media for obtaining high-cell density cultures of halophilic archaea (family Halobacteriaceae) by response surface methodology

Optimization of media components for the growth and biomass production of Halobacterium salinarum VKMM 013 was carried out using response surface methodology. A second order quadratic model was estimated and media components were determined based on quadratic regression equation generated by model. These were 6.35 g L⁻¹ of KCl, 9.70 g L⁻¹ of MgSO₄, 13.38 g L⁻¹ of gelatin and 12.00 g L⁻¹ of soluble starch in nutrient broth supplemented with artificial seawater with 20% (w/v) of NaCl. In these optimal conditions, the obtained cell concentration of 0.746 g L⁻¹ dry weight was in agreement with the predicted cell concentration. The optimized media significantly shortened the time required for cell culture to reach the stationary phase while providing a nearly 2.4-fold increase in biomass production. Furthermore, in cell cultures of three other halophilic archaea the use of optimized media enhanced growth rate and provided high-cell density.     

Effect of varying salinity, temperature, ammonia and nitrous acid concentrations on nitrification of saline wastewater in fixed-bed reactors

Nitrification under changing salinities (0-9%), temperatures (6-50 °C), ammonia (0-5 g N L⁻¹) and nitrite concentrations (0-0.4 g N L⁻¹) was investigated in fixed-bed reactors. For all conditions ammonia oxidation rates (AOR) were lower than nitrite oxidation rates (NOR). AORs and NORs increased from 12.5 to 40 °C and were very low at 6 °C and almost zero at 50 °C. No recovery of nitrification was obtained after incubation at 50 °C, whereas nitrification was restorable after incubation at 6 °C. Ammonia concentrations of 5 g N L⁻¹ or nitrite concentrations up to 0.125 g N L⁻¹ decreased AOR to almost zero. AORs and NORs recovered if ammonia or nitrite was removed. At concentrations of 1 and 5 g N L⁻¹ ammonia AOR and NOR were inhibited by 50%, whereas 27 mg N/L nitrite inhibited AOR by 50%.     

Cultivation of microalgae for oil production with a cultivation strategy of urea limitation

The microalgae, Chlorella sp., were cultivated in various culture modes to assess biomass and lipid productivity in this study. In the batch mode, the biomass concentrations and lipid content of Chlorella sp. cultivated in a medium containing 0.025–0.200 g L⁻¹ urea were 0.464–2.027 g L⁻¹ and 0.661–0.326 g g⁻¹, respectively. The maximum lipid productivity of 0.124 g d⁻¹ L⁻¹ occurred in a medium containing 0.100 g L⁻¹ urea. In the fed-batch cultivation, the highest lipid content was obtained by feeding 0.025 g L⁻¹ of urea during the stationary phase, but the lipid productivity was not significantly increased. However, a semi-continuous process was carried out by harvesting the culture and renewing urea at 0.025 g L⁻¹ each time when the cultivation achieved the early stationary phase. The maximum lipid productivity of 0.139 g d⁻¹ L⁻¹ in the semi-continuous culture was highest in comparison with those in the batch and fed-batch cultivations.     

Performance of a pilot-scale sewage treatment: an up-flow anaerobic sludge blanket (UASB) and a down-flow hanging sponge (DHS) reactors combined system by sulfur-redox reaction process under low-temperature conditions

Performance of a wastewater treatment system utilizing a sulfur-redox reaction of microbes was investigated using a pilot-scale reactor that was fed with actual sewage. The system consisted of an up-flow anaerobic sludge blanket (UASB) reactor and a down-flow hanging sponge (DHS) reactor with a recirculation line. Consequently, the total COD_Cr (465 ± 147 mg L⁻¹; total BOD of 207 ± 68 mg L⁻¹) at the influent was reduced (70 ± 14 mg L⁻¹; total BOD of 9 ± 2 mg L⁻¹) at the DHS effluent under the conditions of an overall hydraulic retention time of 12 h, a recirculation ratio of 2, and a low-sewage temperature of 7.0 ± 2.8 °C. A microbial analysis revealed that sulfate-reducing bacteria contributed to the degradation of organic matter in the UASB reactor even in low temperatures. The utilized sulfur-redox reaction is applicable for low-strength wastewater treatment under low-temperature conditions.     

In silico optimization and low structured kinetic model of poly[(R)-3-hydroxybutyrate] synthesis by Cupriavidus necator DSM 545 by fed-batch cultivation on glycerol

Glycerol was utilized by Cupriavidus necator DSM 545 for production of poly-3-hydroxybutyrate (PHB) in fed-batch fermentation. Maximal specific growth rates (0.12 and 0.3 h⁻¹) and maximal specific non-growth PHB production rate (0.16 g g⁻¹ h⁻¹) were determined from two experiments (inocula from exponential and stationary phase). Saturation constants for nitrogen (0.107 and 0.016 g L⁻¹), glycerol (0.05 g L⁻¹), non-growth related PHB synthesis (0.011 g L⁻¹) and nitrogen/PHB related inhibition constant (0.405 g L⁻¹), were estimated. Five relations for specific growth rate were tested using mathematical models. In silico performed optimization procedures (varied glycerol/nitrogen ratio and feeding) has resulted in a PHB content of 70.9%, shorter cultivation time (23 h) and better PHB yield (0.347 g g⁻¹). Initial concentration of biomass 16.8 g L⁻¹ and glycerol concentration in broth between 3 and 5 g L⁻¹ were decisive factors for increasing of productivity.     

Dynamics of microbial community for X-3B wastewater decolorization coping with high-salt and metal ions conditions

In this study, decolorization of Reactive Brilliant Red X-3B wastewater by the biological process coping with high salinity and metal ions conditions was investigated, and 16S rDNA based fingerprint technique was used to investigate microbial population dynamics. Results of sequencing batch tests showed that the microbial community could keep efficient with high concentration of dye (1100 mg L⁻¹), salt (150 g L⁻¹ NaCl) and some metal ions such as Mg²⁺, Ca²⁺ (1–10 mmol L⁻¹) and Pb²⁺ (1 mmol L⁻¹). 16S rDNA-based molecular analysis techniques demonstrated that the microbial community shifted during the acclimatization process affected by salt or metal ions. Some stains similar to Bacillus, Sedimentibacter, Pseudomonas, Clostridiales, Streptomyces and some uncultured clones acted for the dynamic succession, supposed as potential decolorization bacteria. This study provided insights on the decolorization capability and the population dynamic shifts during decolorization process of azo dye wastewater coping with salt and metal ions.     

Development of chemically defined media supporting high cell density growth of Ketogulonicigenium vulgare and Bacillus megaterium

The immediate precursor of L-ascorbic acid, or vitamin C, is 2-keto-l-gulonic acid (2-KLG). This is commonly produced commercially by Ketogulonicigenium vulgare and Bacillus megaterium, using corn steep liquor powder (CSLP) as an organic nitrogen source. In this study, the effects of the individual CSLP components (amino acids, vitamins, and metal elements) on 2-KLG production were evaluated, with the aim of developing a complete, chemically defined medium for 2-KLG production. Forty components of CSLP were analyzed, and key components were correlated to biomass, 2-KLG productivity, and consumption rate of L-sorbose. Glycine had the greatest effect, followed by serine, biotin, proline, nicotinic acid, and threonine. The combination of 0.28 g L⁻¹ serine, 0.36 g L⁻¹glycine, 0.18 g L⁻¹ threonine, 0.28 g L⁻¹proline, 0.19 g L⁻¹nicotinic acid, and 0.62 mg L⁻¹biotin in a chemically defined medium produced the highest maximum biomass concentration (4.2 × 10⁹ cfu mL⁻¹), 2-KLG concentration (58 g L⁻¹), and yield (0.76 g g⁻¹) after culturing for 28 h.     

Effect of chitosan on UASB treating POME during a transition from mesophilic to thermophilic conditions

The effects of chitosan addition on treatment of palm oil mill effluent were investigated using two lab-scale upflow anaerobic sludge bed (UASB) reactors: (1) with chitosan addition at the dosage of 2 mg chitosan per g volatile suspended solids on the first day of the operation (R1), (2) without chitosan addition (the control, R2). The reactors were inoculated with mesophilic anaerobic sludge which was acclimatized to a thermophilic condition with a stepwise temperature increase of 5 °C from 37 to 57 °C. The OLR ranged from 2.23 to 9.47 kg COD m⁻³ day⁻¹. The difference in biogas production rate increased from non-significant to 18% different. The effluent volatile suspended solids of R1 was 65 mg l⁻¹ lower than that of R2 on Day 123. 16S rRNA targeted denaturing gradient gel electrophoresis (DGGE) fingerprints of microbial community indicated that some methanogens in the genus Methanosaeta can be detected in R1 but not in R2.     

Pentachlorophenol (PCP) dechlorination in horizontal-flow anaerobic immobilized biomass (HAIB) reactors

This study verifies the potential applicability of horizontal-flow anaerobic immobilized biomass (HAIB) reactors to pentachlorophenol (PCP) dechlorination. Two bench-scale HAIB reactors (R1 and R2) were filled with cubic polyurethane foam matrices containing immobilized anaerobic sludge. The reactors were then continuously fed with synthetic wastewater consisting of PCP, glucose, acetic acid, and formic acid as co-substrates for PCP anaerobic degradation. Before being immobilized in polyurethane foam matrices, the biomass was exposed to wastewater containing PCP in reactors fed at a semi-continuous rate of 2.0 μg PCP g⁻¹ VS. The applied PCP loading rate was increased from 0.05 to 2.59 mg PCP l⁻¹ day⁻¹ for R1, and from 0.06 to 4.15 mg PCP l⁻¹ day⁻¹ for R2. The organic loading rates (OLR) were 1.1 and 1.7 kg COD m⁻³ day⁻¹ at hydraulic retention times (HRT) of 24 h for R1 and 18 h for R2. Under such conditions, chemical oxygen demand (COD) removal efficiencies of up to 98% were achieved in the HAIB reactors. Both reactors exhibited the ability to remove 97% of the loaded PCP. Dichlorophenol (DCP) was the primary chlorophenol detected in the effluent. The adsorption of PCP and metabolites formed during PCP degradation in the packed bed was negligible for PCP removal efficiency.     

Vertical tubular photobioreactor for semicontinuous culture of Cyanobium sp

We evaluated the kinetic culture characteristics of the microalgae Cyanobium sp. grown in vertical tubular photobioreactor in semicontinuous mode. Cultivation was carried out in vertical tubular photobioreactor for 2 L, in 57 d, at 30 °C, 3200 Lux, and 12 h light/dark photoperiod. The maximum specific growth rate was found as 0.127 d⁻¹, when the culture had blend concentration of 1.0 g L⁻¹, renewal rate of 50%, and sodium bicarbonate concentration of 1.0 g L⁻¹. The maximum values of productivity (0.071 g L⁻¹ d⁻¹) and number of cycles (10) were observed in blend concentration of 1.0 g L⁻¹, renewal rate of 30%, and bicarbonate concentration of 1.0 g L⁻¹. The results showed the potential of semicontinuous cultivation of Cyanobium sp. in closed tubular bioreactor, combining factors such as blend concentration, renewal rate, and sodium bicarbonate concentration.     

Aerobic granular sludge formation for high strength agro-based wastewater treatment

The present study investigates the formation of aerobic granular sludge in sequencing batch reactor (SBR) fed with palm oil mill effluent (POME). Stable granules were observed in the reactor with diameters between 2.0 and 4.0 mm at a chemical oxygen demand (COD) loading rate of 2.5 kg COD m⁻³ d⁻¹. The biomass concentration was 7600 mg L⁻¹ while the sludge volume index (SVI) was 31.3 mL g SS⁻¹ indicating good biomass accumulation in the reactor and good settling properties of granular sludge, respectively. COD and ammonia removals were achieved at a maximum of 91.1% and 97.6%, respectively while color removal averaged at only 38%. This study provides insights on the development and the capabilities of aerobic granular sludge in POME treatment.     

Effect of lignocellulosic inhibitory compounds on growth and ethanol fermentation of newly-isolated thermotolerant Issatchenkia orientalis

A newly isolated thermotolerant ethanologenic yeast strain, Issatchenkia orientalis IPE 100, was able to produce ethanol with a theoretical yield of 85% per g of glucose at 42 °C. Ethanol production was inhibited by furfural, hydroxymethylfurfural and vanillin concentrations above 5.56 g L⁻¹, 7.81 g L⁻¹, and 3.17 g L⁻¹, respectively, but the strain was able to produce ethanol from enzymatically hydrolyzed steam-exploded cornstalk with 93.8% of theoretical yield and 0.91 g L⁻¹ h⁻¹ of productivity at 42 °C. Therefore, I. orientalis IPE 100 is a potential candidate for commercial lignocelluloses-to-ethanol production.     

3-Phenyllactic acid production by substrate feeding and pH-control in fed-batch fermentation of Lactobacillus sp. SK007

3-Phenyllactic acid (PLA), which is produced by some strains of lactic acid bacteria (LAB), is a known antimicrobial agent with a broad spectrum. Batch and fed-batch fermentation by the strain Lactobacillus sp. SK007 for PLA production have been reported. With batch fermentation without pH-control, PLA production yield was 2.42 g L⁻¹. When fed-batch fermentation by Lactobacillus sp. SK007 was conducted in 3 L initial volume with pH-control at 6.0 and intermittent feeding, which was developed after fermentation for 12 h and every 2 h with 120 mL 100 g L⁻¹ PPA phenylpyruvic acid (PPA) and 50 mL 500 g L⁻¹ glucose each time, PLA production yield reached 17.38 g L⁻¹. The final conversion ratio of PPA to PLA was 51.1%, and the PLA production rate was 0.241 g L⁻¹ h⁻¹. This indicated that PPA was the ideal substrate for PLA fermentation production, and fed-batch fermentation with intermittent PPA feeding and pH-control was an effective approach to improve PLA production yield.     

Bioethanol fermentation of concentrated rice straw hydrolysate using co-culture of Saccharomyces cerevisiae and Pichia stipitis

Rice straw is one of the abundant lignocellulosic feed stocks in the world and has been selected for producing ethanol at an economically feasible manner. It contains a mixture of sugars (hexoses and pentoses).Biphasic acid hydrolysis was carried out with sulphuric acid using rice straw. After acid hydrolysis, the sugars, furans and phenolics were estimated. The initial concentration of sugar was found to be 16.8 g L⁻¹. However to increase the ethanol yield, the initial sugar concentration of the hydrolysate was concentrated to 31 g L⁻¹ by vacuum distillation. The concentration of sugars, phenols and furans was checked and later detoxified by over liming to use for ethanol fermentation. Ethanol concentration was found to be 12 g L⁻¹, with a yield, volumetric ethanol productivity and fermentation efficiency of 0.33 g L⁻¹ h⁻¹, 0.4 g g⁻¹ and 95%, respectively by co-culture of OVB 11 (Saccharomyces cerevisiae) and Pichia stipitis NCIM 3498.     

Alkyl-methylimidazolium ionic liquids affect the growth and fermentative metabolism of Clostridium sp

In this study, the effect of ionic liquids, 1-ethyl-3-methylimidazolium acetate [EMIM][Ac], 1-ethyl-3-methylimidazolium diethylphosphate [EMIM][DEP], and 1-methyl-3-methylimidazolium dimethylphosphate [MMIM][DMP] on the growth and glucose fermentation of Clostridium sp. was investigated. Among the three ionic liquids tested, [MMIM][DMP] was found to be least toxic. Growth of Clostridium sp. was not inhibited up to 2.5, 4 and 4 g L⁻¹ of [EMIM][Ac], [EMIM][DEP] and [MMIM][DMP], respectively. [EMIM][Ac] at <2.5 g L⁻¹, showed hormetic effect and stimulated the growth and fermentation by modulating medium pH. Total organic acid production increased in the presence of 2.5 and 2 g L⁻¹ of [EMIM][Ac] and [MMIM][DMP]. Ionic liquids had no significant influence on alcohol production at <2.5 g L⁻¹. Total gas production was affected by ILs at ?2.5 g L⁻¹ and varied with type of methylimidazolium IL. Overall, the results show that the growth and fermentative metabolism of Clostridium sp. is not impacted by ILs at concentrations below 2.5 g L⁻¹.     

Modeling of biomass production by Spirulinaplatensis as function of phosphate concentrations and pH regimes

Batch cultivations were performed to evaluate the influence of phosphate concentrations (0.25, 0.5, 0.75, and 1.0 g L⁻¹) for pH regimes (9.5, 10.0, and 10.5) on the biomass production by Spirulina platensis. The best condition for cell growth (3.099 g L⁻¹) was found at 0.5 g L⁻¹ phosphate and pH value of 10.0. Cultivation time, phosphate, and pH caused to increase significantly (p < 0.01) in biomass production by S. platensis. Lag time was observed up to 4 h. After then, biomass production increased sharply (p < 0.01) from 0.020 g L⁻¹ to 2.063, 2.213, 1.532, and 0.797 g L⁻¹ at 0.25, 0.5, 0.75, and 1.0 g L⁻¹ phosphate values, respectively. Modified Gompertz model could be regarded as sufficient to describe the biomass production by S. platensis with high determination coefficients and low sum of square value indicated that. Biological parameters for biomass production were successfully predicted by modified Gompertz model.