首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Mechanical forces are known to affect the biomechanical properties of native and engineered cardiovascular tissue. In particular, shear stress that results from the relative motion of heart valve leaflets with respect to the blood flow is one important component of their mechanical environment in vivo. Although different types of bioreactors have been designed to subject cells to shear stress, devices to expose biological tissue are few. In an effort to address this issue, the aim of this study was to design an ex vivo tissue culture system to characterize the biological response of heart valve leaflets subjected to a well-defined steady or time-varying shear stress environment. The novel apparatus was designed based on a cone-and-plate viscometer. The device characteristics were defined to limit the secondary flow effects inherent to this particular geometry. The determination of the operating conditions producing the desired shear stress profile was streamlined using a computational fluid dynamic (CFD) model validated with laser Doppler velocimetry. The novel ex vivo tissue culture system was validated in terms of its capability to reproduce a desired cone rotation and to maintain sterile conditions. The CFD results demonstrated that a cone angle of 0.5 deg, a cone radius of 40 mm, and a gap of 0.2 mm between the cone apex and the plate could limit radial secondary flow effects. The novel cone-and-plate permits to expose nine tissue specimens to an identical shear stress waveform. The whole setup is capable of accommodating four cone-and-plate systems, thus concomitantly subjecting 36 tissue samples to desired shear stress condition. The innovative design enables the tissue specimens to be flush mounted in the plate in order to limit flow perturbations caused by the tissue thickness. The device is capable of producing shear stress rates of up to 650 dyn cm(-2) s(-1) (i.e., maximum shear stress rate experienced by the ventricular surface of an aortic valve leaflet) and was shown to maintain tissue under sterile conditions for 120 h. The novel ex vivo tissue culture system constitutes a valuable tool toward elucidating heart valve mechanobiology. Ultimately, this knowledge will permit the production of functional tissue engineered heart valves, and a better understanding of heart valve biology and disease progression.  相似文献   

2.
In this study, the magnetic resonance (MR) elastography technique was used to estimate the dynamic shear modulus of mouse brain tissue in vivo. The technique allows visualization and measurement of mechanical shear waves excited by lateral vibration of the skull. Quantitative measurements of displacement in three dimensions during vibration at 1200 Hz were obtained by applying oscillatory magnetic field gradients at the same frequency during a MR imaging sequence. Contrast in the resulting phase images of the mouse brain is proportional to displacement. To obtain estimates of shear modulus, measured displacement fields were fitted to the shear wave equation. Validation of the procedure was performed on gel characterized by independent rheometry tests and on data from finite element simulations. Brain tissue is, in reality, viscoelastic and nonlinear. The current estimates of dynamic shear modulus are strictly relevant only to small oscillations at a specific frequency, but these estimates may be obtained at high frequencies (and thus high deformation rates), noninvasively throughout the brain. These data complement measurements of nonlinear viscoelastic properties obtained by others at slower rates, either ex vivo or invasively.  相似文献   

3.
The purpose of this study was to assess the stability of protein formulations using a device designed to generate defined, quantifiable levels of shear in the presence of a solid-liquid interface. The device, based on a rotating disk, produced shear strain rates of up to 3.4 x 10(4) s(-1) (at 250 rps) and was designed to exclude air-liquid interfaces and enable temperature to be controlled. Computational fluid dynamics (CFD) was used to study the fluid flow patterns within the device and to determine the shear strain rate (s(-1)) at a range of disk speeds. The device was then used to study the effect on a monoclonal IgG4 of high levels of shear at the solid-liquid interface. Monomeric antibody concentration and aggregation of the protein in solution were monitored by gel permeation HPLC and turbidity at 350 nm. High shear strain rates were found to cause significant levels of protein aggregation and precipitation with reduction of protein monomer following first-order kinetics. Monomer reduction rate was determined for a range of disk speeds and found to have a nonlinear relationship with shear strain rate, indicating the importance of identifying and minimizing such environments during processing.  相似文献   

4.
This study combines non-invasive mechanical testing with finite element (FE) modelling to assess for the first time the reliability of shear wave (SW) elastography for the quantitative assessment of the in-vivo nonlinear mechanical behavior of heel-pad. The heel-pads of five volunteers were compressed using a custom-made ultrasound indentation device. Tissue deformation was assessed from B-mode ultrasound and force was measured using a load cell to calculate the force – deformation graph of the indentation test. These results were used to design subject specific FE models and to inverse engineer the tissue’s hyperelastic material coefficients and its stress – strain behavior. SW speed was measured for different levels of compression (from 0% to 50% compression). SW speed for 0% compression was used to assess the initial stiffness of heel-pad (i.e. initial shear modulus, initial Young’s modulus). Changes in SW speed with increasing compressive loading were used to quantify the tissue’s nonlinear mechanical behavior based on the theory of acoustoelasticity. Statistical analysis of results showed significant correlation between SW-based and FE-based estimations of initial stiffness, but SW underestimated initial shear modulus by 64%(±16). A linear relationship was found between the SW-based and FE-based estimations of nonlinear behavior. The results of this study indicate that SW elastography is capable of reliably assessing differences in stiffness, but the absolute values of stiffness should be used with caution. Measuring changes in SW speed for different magnitudes of compression enables the quantification of the tissue’s nonlinear behavior which can significantly enhance the diagnostic value of SW elastography.  相似文献   

5.
We describe an experimental method and apparatus for the estimation of constitutive parameters of soft tissue using Magnetic Resonance Imaging (MRI), in particular for the estimation of passive myocardial material properties. MRI tissue tagged images were acquired with simultaneous pressure recordings, while the tissue was cyclically deformed using a custom built reciprocating pump actuator A continuous three-dimensional (3D) displacement field was reconstructed from the imaged tag motion. Cavity volume changes and local tissue microstructure were determined from phase contrast velocity and diffusion tensor MR images, respectively. The Finite Element Method (FEM) was used to solve the finite elasticity problem and obtain the displacement field that satisfied the applied boundary conditions and a given set of material parameters. The material parameters which best fit the FEM predicted displacements to the displacements reconstructed from the tagged images were found by nonlinear optimization. The equipment and method were validated using inflation of a deformable silicon gel phantom in the shape of a cylindrical annulus. The silicon gel was well described by a neo-Hookian material law with a single material parameter C1=8.71+/-0.06kPa, estimated independently using a rotational shear apparatus. The MRI derived parameter was allowed to vary regionally and was estimated as C1 =8.80+/-0.86kPa across the model. Preliminary results from the passive inflation of an isolated arrested pig heart are also presented, demonstrating the feasibility of the apparatus and method for isolated heart preparations. FEM based models can therefore estimate constitutive parameters accurately and reliably from MRI tagging data.  相似文献   

6.
Quantitatively reproducible results were obtained by using a new device for preparation gel electrophoresis combined with polyacrylamide-agarose composite gel. When an adequate gel-buffer system was selected according to the procedure described in this paper, proteins and RNA's were well separated and recovered. The new device for preparative gel electrophoresis and the method for preparation of polyacrylamide-agarose composite gel are presented together with the elution profiles of the recovered substances.  相似文献   

7.
Quantitatively reproducible results were obtained by using a new device for preparative gel electrophoresis combined with polyacrylamide-agarose composite gel. When an adequate gel-buffer system was selected according to the procedure described in this paper, proteins and RNA's were well separated and recovered. The new device for preparative gel electrophoresis and the method for preparation of polyacrylamide-agarose composite gel are presented together with the elution profiles of the recovered substances.  相似文献   

8.
Effect of shear on plasmid DNA in solution   总被引:2,自引:0,他引:2  
This study was designed to evaluate the effect of shear on the supercoiled circular (SC) form of plasmid DNA. The conditions chosen are representative of those occurring during the processing of plasmid-based genes for gene therapy and DNA vaccination. Controlled shear was generated using a capillary rheometer and a rotating disk shear device. Plasmid DNA was tested in a clarified alkaline lysate solution. This chemical environment is characteristic of the early stages of plasmid purification. Quantitative data is reported on shear degradation of three homologous recombinant plasmids of 13, 20 and 29 kb in size. Shear sensitivity increased dramatically with plasmid molecular weight. Ultrapure plasmid DNA redissolved in 10 mM Tris/HCl, 1 mM EDTA pH 8 (TE buffer) was subjected to shear using the capillary rheometer. The shear sensitivity of the three plasmids was similar to that observed for the same plasmids in the clarified alkaline lysate. Further experiments were carried out using the 20 kb plasmid and the rotating disk shear device. In contrast with the capillary rheometer data, ultrapure DNA redissolved in TE buffer was up to eight times more sensitive to shear compared to plasmid DNA in the clarified alkaline lysate. However, this enhanced sensitivity decreased when the ionic strength of the solution was raised by the addition of NaCl to 150 mM. In addition, shear damage was found to be independent of plasmid DNA concentration in the range from 0.2 7g/ml to 20 7g/ml. The combination of shear and air-liquid interfaces caused extensive degradation of the plasmid DNA. The damage was more evident at low ionic strength and low DNA concentration. These findings show that the tertiary structure of plasmid DNA can be severely affected by shear forces. The extent of damage was found to be critically dependent on plasmid size and the ionic strength of the environment. The interaction of shear with air-liquid interfaces shows the highest potential for damaging SC plasmid DNA during bioprocesses.  相似文献   

9.
The rheological properties of the stratum corneum of the pilot whale (Globicephala melas) were investigated with emphasis on their significance to the self-cleaning abilities of the skin surface smoothed by a jelly material enriched with various hydrolytic enzymes. The gel formation of the collected fluid was monitored by applying periodic-harmonic oscillating loads using a stress-controlled rheometer. In the mechanical spectrum of the gel, the plateau region of the storage modulus G' (<1200 Pa) and the loss modulus G" (>120 Pa) were independent of frequency (omega = 43.98 to 0.13 rad x s(-1), tau = 15 Pa, T = 20 degrees C), indicating high elastic performance of a covalently cross-linked viscoelastic solid. In addition, multi-angle laser light scattering experiments (MALLS) were performed to analyse the potential time-dependent changes in the weight-average molar mass of the samples. The observed increase showed that the gel formation is based on the assembly of covalently cross-linked aggregates. The viscoelastic properties and the shear resistance of the gel assure that the enzyme-containing jelly material smoothing the skin surface is not removed from the stratum corneum by shear regimes during dolphin jumping. The even skin surface is considered to be most important for the self-cleaning abilities of the dolphin skin against biofouling.  相似文献   

10.
Shear linear behavior of brain tissue over a large frequency range   总被引:3,自引:0,他引:3  
The literature review about the shear linear properties of brain tissue reveals both a large discrepancy in the existing data and a crucial lack of information at high frequencies associated with traffic road and non-penetrating ballistic impacts. The purpose of this study is to clarify and to complement the linear material characterisation of brain tissue. New data at small strains and high frequencies were obtained from oscillatory experiments. The tests were performed on thin porcine white matter samples (corona radiata) using an original custom-designed oscillatory shear testing device. At 37 degrees C, the results showed that the mean storage modulus (G') and the mean loss modulus (G') increased with the frequency (0.1 to 6310 Hz) from 2.1+/-0.9 kPa to 16.8+/-2.0 kPa and from 0.4+/-0.2 kPa to 18.7+/-2.3 kPa respectively. The reliability of these new dynamic data was checked over a partially common frequency range by conducting similar experiments using a standard rheometer (Bohlin C-VOR 150). Data were also compared in the time field. From these experiments, the relaxation modulus (G(t)) was found to decrease from 24.4+/-2.1 kPa to 1.0+/-0.3 kPa between 10(-5) s and 270 s.  相似文献   

11.
This study tested the hypothesis that controlled flow through microchannels can cause shear-induced intracellular loading of cells with molecules. The overall goal was to design a simple device to expose cells to fluid shear stress and thereby increase plasma membrane permeability. DU145 prostate cancer cells were exposed to fluid shear stress in the presence of fluorescent cell-impermeant molecules by using a cone-and-plate shearing device or high-velocity flow through microchannels. Using a syringe pump, cell suspensions were flowed through microchannels of 50-300 microm diameter drilled through Mylar sheets using an excimer laser. As quantified by flow cytometry, intracellular uptake and loss of viability correlated with the average shear stress. Optimal results were observed when exposing the cells to high shear stress for short durations in conical channels, which yielded uptake to over one-third of cells while maintaining viability at approximately 80%. This method was capable of loading cells with molecules including calcein (0.62 kDa), large molecule weight dextrans (150-2,000 kDa), and bovine serum albumin (66 kDa). These results supported the hypothesis that shear-induced intracellular uptake could be generated by flow of cell suspensions through microchannels and further led to the design of a simple, inexpensive, and effective device to deliver molecules into cells. Such a device could benefit biological research and the biotechnology industry.  相似文献   

12.
An experimental investigation of the wall shear stress distribution downstream of a backward-facing step is carried out. The wall shear stress distribution was determined by measuring the deformation of a gel layer, attached to the wall downstream of the step. Speckle pattern interferometry was applied to measure the deformation of the gel layer. The measured deformation, combined with the properties of the gel layer, served as an input for a finite element solid mechanics computation to determine the stress distribution in the gel layer. The wall shear stress, required to generate the measured deformation of the gel layer, was determined from these computations. A Newtonian buffer solution and a non-Newtonian red blood cell suspension were used as measuring fluids. The deformation of the gel layer was determined for a Newtonian buffer solution to evaluate the method and to obtain the properties of the gel layer. Subsequently, the wall shear stress distribution for the non-Newtonian red blood cell suspension was determined for three different flow rates. The inelastic non-Newtonian Carreau-Yasuda model served as constitutive model for the red blood cell suspension. Using this model, the velocity and wall shear stress distribution were computed by means of a finite element fluid mechanics computation. From the comparison between the numerical and the experimental results, it can be concluded that wall shear stresses, induced by the red blood cell suspension, can be modeled accurately by employing a Carreau-Yasuda model.  相似文献   

13.
The sol–gel transition in aqueous alginate solutions of four alginate samples having different molecular weights (MW) and M/G ratios induced by cupric cations was monitored by rheology measurements. The gel point fgel and the relaxation critical exponent n were determined using the Winter’s criterion over the alginate concentration CAlg of 1–4 wt%. The scaling for the zero shear viscosity η0 before the gel point and the equilibrium modulus Ge after the gel point was established against the relative distance ε from the gel point at the concentration of CAlg = 1 wt%, giving the critical exponents k and z. The results indicated that fgel was almost independent of the alginate concentration and became higher for the sample with lower molecular weight. The critical exponent n decreased with the increase in CAlg for these four Cu-alginate samples and the fractal dimension df estimated from n suggested a denser structure in the critical gel with high G content. The critical exponent n evaluated from k and z agreed well with n determined from the Winter’s criterion.  相似文献   

14.
We were the first to examine the mechanical responses of skeletally mature bovine femoral cartilage under large-strain simple shear (up to ±20%) using a multiaxial shear testing device. Since shear loading is critical in both tissue failure and chondrocyte responses, we aimed to probe (1) anisotropy with respect to the split-line direction (principal alignment of the collagen fibers near the articulating surface), (2) heterogeneity between femoral condyles, and (3) the influence of local cartilage thickness. We harvested a total of 48 cuboid cartilage specimens from four bovine knee joints. With each specimen we applied shear strains both parallel and perpendicular to the local split-line direction at a rate of 75 μm/min and calculated the peak-to-peak shear stresses, shear strain–energy dissipation densities, and peak effective shear moduli. The Wilcoxon signed rank test revealed that the medial condyle was anisotropic in some mechanical measures at applied shear strains above 5%, while the lateral condyle was mechanically isotropic at all applied shear strains. The Kruskal–Wallis test revealed no significant differences in the median mechanical behavior of the lateral and medial condyles. Spearman׳s rank correlations revealed statistically significant negative monotonic correlations among thickness and most of our mechanical measures for both lateral and medial condyles at most applied strains and directions of applied shear. These results suggest that large-strain analyses account for nonlinear, anisotropic and location-dependent effects not fully realized at small strains. Our findings may inspire new experiments and models that consider anisotropy and heterogeneity of cartilage in ways previously ignored.  相似文献   

15.
The response of endothelial cells (ECs) to their hemodynamic environment strongly influences normal vascular physiology and the pathogenesis of atherosclerosis. Unique responses to the complex flow patterns in lesion-prone regions imply that the temporal and spatial features of the mechanical stimuli modulate the cellular response to flow. We report the first systematic study of the effects of temporal gradients of shear stress on ECs. Flow was applied to cultured ECs using a novel cone-and-plate device allowing precise and independent control of the shear stress magnitude and the onset rate. Intracellular free calcium concentration ([Ca2+]i) increased rapidly following the onset of flow, and the characteristics of the transient were modulated by both the shear stress magnitude and onset rate. ECs were most sensitive to shear stress applied at physiological onset rates. Furthermore, the relative contribution of extracellular calcium and IP3-mediated release were dependent upon the specific flow regime.  相似文献   

16.
Human pluripotent stem cell-derived endothelial cells (hPSC-ECs) present an attractive alternative to primary EC sources for vascular grafting. However, there is a need to mature them towards either an arterial or venous subtype. A vital environmental factor involved in the arteriovenous specification of ECs during early embryonic development is fluid shear stress; therefore, there have been attempts to employ adult arterial shear stress conditions to mature hPSC-ECs. However, hPSC-ECs are naïve to fluid shear stress, and their shear responses are still not well understood. Here, we used a multiplex microfluidic platform to systematically investigate the dose-time shear responses on hPSC-EC morphology and arterial-venous phenotypes over a range of magnitudes coincidental with physiological levels of embryonic and adult vasculatures. The device comprised of six parallel cell culture chambers that were individually linked to flow-setting resistance channels, allowing us to simultaneously apply shear stress ranging from 0.4 to 15 dyne/cm 2. We found that hPSC-ECs required up to 40 hr of shear exposure to elicit a stable phenotypic change. Cell alignment was visible at shear stress <1 dyne/cm 2, which was independent of shear stress magnitude and duration of exposure. We discovered that the arterial markers NOTCH1 and EphrinB2 exhibited a dose-dependent increase in a similar manner beyond a threshold level of 3.8 dyne/cm 2, whereas the venous markers COUP-TFII and EphB4 expression remained relatively constant across different magnitudes. These findings indicated that hPSC-ECs were sensitive to relatively low magnitudes of shear stress, and a critical level of ~4 dyne/cm 2 was sufficient to preferentially enhance their maturation into an arterial phenotype for future vascular tissue engineering applications.  相似文献   

17.
Shear stress stimulus is expected to enhance angiogenesis, the formation of microvessels. We determined the effect of shear stress stimulus on three-dimensional microvessel formation in vitro. Bovine pulmonary microvascular endothelial cells were seeded onto collagen gels with basic fibroblast growth factor to make a microvessel formation model. We observed this model in detail using phase-contrast microscopy, confocal laser scanning microscopy, and electron microscopy. The results show that cells invaded the collagen gel and reconstructed the tubular structures, containing a clearly defined lumen consisting of multiple cells. The model was placed in a parallel-plate flow chamber. A laminar shear stress of 0.3 Pa was applied to the surfaces of the cells for 48 h. Promotion of microvessel network formation was detectable after approximately 10 h in the flow chamber. After 48 h, the length of networks exposed to shear stress was 6.17 (+/-0.59) times longer than at the initial state, whereas the length of networks not exposed to shear stress was only 3.30 (+/-0.41) times longer. The number of bifurcations and endpoints increased for networks exposed to shear stress, whereas the number of bifurcations alone increased for networks not exposed to shear stress. These results demonstrate that shear stress applied to the surfaces of endothelial cells on collagen gel promotes the growth of microvessel network formation in the gel and expands the network because of repeated bifurcation and elongation.  相似文献   

18.
A rat model was used to distinguish between the different factors that contribute to muscle tissue damage related to deep pressure ulcers that develop after compressive loading. The separate and combined effects of ischemia and deformation were studied. Loading was applied to the hindlimb of rats for 2 h. Muscle tissue was examined using MR imaging (MRI) and histology. An MR-compatible loading device allowed simultaneous loading and measurement of tissue status. Two separate loading protocols incorporated uniaxial loading, resulting in tissue compression and ischemic loading. Uniaxial loading was applied to the tibialis anterior by means of an indenter, and ischemic loading was accomplished with an inflatable tourniquet. Deformation of the muscle tissue during uniaxial loading was measured using MR tagging. Compression of the tissues for 2 h led to increased T2 values, which were correlated to necrotic regions in the tibialis anterior. Perfusion measurements, by means of contrast-enhanced MRI, indicated a large ischemic region during indentation. Pure ischemic loading for 2 h led to reversible tissue changes. From the MR-tagging experiments, local strain fields were calculated. A 4.5-mm deformation, corresponding to a surface pressure of 150 kPa, resulted in maximum shear strain up to 1.0. There was a good correlation between the location of damage and the location of high shear strain. It was concluded that the large deformations, in conjunction with ischemia, provided the main trigger for irreversible muscle damage.  相似文献   

19.
Background aimsMesenchymal stromal cells (MSCs) have been studied as cell therapy to treat a vast array of diseases. In clinical MSC production, the isolated cells must undergo extensive ex vivo expansion to obtain a sufficient dose of MSCs for the investigational treatment. However, extended tissue culture is fraught with potential hazards, including contamination and malignant transformation. Changes of gene expression with prolonged culture may alter the therapeutic potential of the cells. Increasing the recovery of MSCs from the freshly harvested bone marrow allowing for less ex vivo expansion would represent a major advance in MSC therapy.MethodsHuman bone marrow cells from eight healthy donors were processed using a marrow filter device and, in parallel, using buoyant density centrifugation by two independent investigators. The initial nucleated cell recovery and the final yield, immunophenotype and trilineage differentiation potential of second-passage MSCs were examined.ResultsThe marrow filter device generated significantly greater initial cell recovery requiring less investigator time and resulted in approximately 2.5-fold more MSCs after the second passage. The immunophenotype and differentiation potential of MSCs isolated using the two methods were equivalent and consistent with the defining criteria. The two independent investigators generated comparable results.ConclusionsThis novel filter device is a fast, efficient and reliable system to isolate MSCs and should greatly expedite pre-clinical and clinical investigations of MSC therapy.  相似文献   

20.
Cells are complex, dynamic systems that respond to various in vivo stimuli including chemical, mechanical, and scaffolding alterations. The influence of mechanics on cells is especially important in physiological areas that dictate what modes of mechanics exist. Complex, multivariate physiological responses can result from multi-factorial, multi-mode mechanics, including tension, compression, or shear stresses. In this study, we present a novel device based on elastomeric materials that allowed us to stimulate NIH 3T3 fibroblasts through uniaxial strip stretching or shear fluid flow. Cell shape and structural response was observed using conventional approaches such as fluorescent microscopy. Cell orientation and actin cytoskeleton alignment along the direction of applied force were observed to occur after an initial 3 h time period for shear fluid flow and static uniaxial strip stretching experiments although these two directions of alignment were oriented orthogonal relative to each other. This response was then followed by an increasingly pronounced cell and actin cytoskeleton alignment parallel to the direction of force after 6, 12, and 24 h, with 85% of the cells aligned along the direction of force after 24 h. These results indicate that our novel device could be implemented to study the effects of multiple modes of mechanical stimulation on living cells while probing their structural response especially with respect to competing directions of alignment and orientation under these different modes of mechanical stimulation. We believe that this will be important in a diversity of fields including cell mechanotransduction, cell–material interactions, biophysics, and tissue engineering.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号