Plasticization of poly(L-lactide) with poly(propylene glycol)

A new plasticizer for poly(L-lactide) (PLA)-poly(propylene glycol) (PPG) is proposed. The advantage of using PPG is that it does not crystallize, has low glass transition temperature, and is miscible with PLA. PLA was plasticized with PPGs with nominal Mw of 425 and 1000 g/mol. Poly(ethylene glycol) (PEG), long known as a plasticizer for PLA, with nominal Mw of 600 g/mol, was also used to plasticize PLA for comparison. The thermal and tensile properties of PLA and PLA with 5-12.5 wt % of the plasticizers were studied. In blends of PLA with PPGs the glass transition temperature was lower than that of neat PLA. Both PPGs enhanced the crystallizability of PLA albeit less than PEG. All of the plasticizers increased also the ability of PLA to plastic deformation which was reflected in a decrease of yield stress and in an increase of elongation at break. The effect was enhanced by the higher PPG content and also by lower molecular weight of PPG. A phase separation occurred only in the blend containing 12.5 wt % of PPG with higher molecular weight. The evidences of crazing were found in deformed samples of PLA with low plasticizer content, whereas the samples with higher content of plasticizers crystallized due to deformation.     

Designed chain architecture for enhanced migration resistance and property preservation in poly(vinyl chloride)/polyester blends

Blends of poly(vinyl chloride) (PVC) and poly(butylene adipate) (PBA) with varying degrees of branching were analyzed with respect to migration resistance during aging in water, preservation of material properties, and thermal stability. Gas chromatography-mass spectrometry, water absorption, weight loss, thermogravimetric analysis, Fourier transform infrared spectroscopy, contact angle, tensile testing, and differential scanning calorimetry were used to analyze the blends before and after aging in water for 6 weeks. Films plasticized with slightly branched polyester maintained their material and mechanical properties best during aging. High degree of branching was accompanied by poor miscibility, increased hydrophilicity, and polydispersity, and highly branched PBA was not favorable as a plasticizer. Strong intermolecular interactions reduced the water absorption and increased the migration resistance of the blends. Polymeric plasticizers with no, low, or moderate degree of branching improved the thermal stability of films compared to films plasticized with a traditional phthalate plasticizer. Proper design of plasticizer architecture led, thus, to improved migration resistance, long-term properties, and thermal stability in PVC/polyester blends.     

Biodegradable films of partly branched poly(l-lactide)-co-poly(epsilon-caprolactone) copolymer: modulation of phase morphology, plasticization properties and thermal depolymerization

We report on the modulation of phase morphology, plasticization properties, and thermal stability of films of partly branched poly(l-lactide)-co-poly(epsilon-caprolactone) copolymer (PLLA-co-PCL) with additions of low molecular weight compounds, namely, triethyl citrate ester, diethyl phthalate, diepoxy polyether (poly(propylene glycol) diglycidyl ether), and with epoxidized soybean oil (ESO). The PLLA-co-PCL/polyether films showed significant stability against thermal depolymerization, high film flexibility, and good plasticizing properties, probably due to cross-linking and chain branching formation between diepoxy groups with both the end carboxyl and hydroxyl groups of the PLLA copolymer (initially present or generated during the degradation process) to produce primary ester and ether bonds, respectively. Diethyl phthalate and triethyl citrate ester were found to be efficient plasticizers for PLLA copolymer in terms of glass transition and mechanical properties, but the more water-soluble plasticizer triethyl citrate induced a dramatic loss in the molecular weight of the copolymer. Although ESO cannot play the role of a plasticizer, it substantially stabilizes and retards thermal depolymerization of the PLLA copolymer matrix, possibly because of a reaction between epoxy groups with the end carboxyl and hydroxyl groups of the PLLA copolymer. The presence of ESO in PLLA-co-PCL/ESO/triethyl citrate blends enhanced the compatibility and miscibility of the plasticizer with the PLLA copolymer matrix, considerably improved the mechanical properties (elongation at break), and substantially stabilized the copolymer against thermal depolymerization. It seems likely that the epoxy groups interact not only with the end hydroxyl and carboxyl group of the copolymer but as well with the hydroxyl group of triethyl citrate plasticizer to produce a new ether bond (C-O-C) as the cross-linking unit. On the other hand, for PLLA-co-PCL/ESO/polyether blends, (80/10/10) epoxidized oil distorts the compactness of the blend by diminishing the proposed entanglements between carboxyl, hydroxyl, and diepoxy groups of polyether and reduces the high elongation properties otherwise observed in the PLLA-co-PCL/polyether films. The multicomponent approach toward modulating poly(l-lactide)-co-poly(epsilon-caprolactone) copolymer films using epoxy compounds and plasticizers and the insight into the nature of various PLLA matrixes presented here offer advantages to a broad engineering of PLLA copolymer films having desirable physical properties and multiphase behavior for efficient uses in future technical applications.     

Plasticized waxy maize starch: effect of polyols and relative humidity on material properties

The plasticizing effect of different polyols such as glycerol, xylitol, sorbitol, and maltitol on waxy maize starch was investigated. The concentration of plasticizer was fixed at 33 wt % (dry basis of starch). The structure and mechanical performance of resulting films conditioned at different relative humidity levels were studied in detail. The effect of the plasticizer on the glass-rubber transition temperature (T(g)) and crystallinity was characterized using differential scanning calorimetry. It was found that T(g) decreases with increasing moisture content and decreasing molecular weight of the plasticizer. The water resistance of starch increased steadily with the molecular weight of the plasticizer and was directly proportional to the ratio of the end to total hydroxyl groups. As the molecular weight of the plasticizer increased, the brittleness of the dry system increased. However, the use of high molecular plasticizer allowed good mechanical properties of the moist material to be obtained in terms of both stiffness and elongation at break.     

A study of conformational stability of poly(L-alanine), poly(L-valine), and poly(L-alanine)/poly(L-valine) blends in the solid state by (13)C cross-polarization/magic angle spinning NMR

13C cross-polarization/magic angle spinning (CP/MAS) NMR and (1)H T(1rho) experiments of poly(L-alanine) (PLA), poly(L-valine) (PLV), and PLA/PLV blends have been carried out in order to elucidate the conformational stability of the polypeptides in the solid state. These were prepared by adding a trifluoroacetic acid (TFA) solution of the polymer with a 2.0 wt/wt % of sulfuric acid (H(2)SO(4)) to alkaline water. From these experimental results, it is clarified that the conformations of PLA and PLV in their blends are strongly influenced by intermolecular hydrogen-bonding interactions that cause their miscibility at the molecular level.     

In situ formation of blends by photopolymerization of poly(ethylene glycol) dimethacrylate and polylactide

Blends of cross-linked poly(ethylene glycol) dimethacrylate (PEGDMA) and poly(d,l-lactide) (PLA) were prepared by mixing photoactive PEGDMA (molecular mass: 875 g/mol) and PLA, and subsequently photopolymerizing the mixture with visible light. The effects of PLA molecular mass and mass fraction on the rheological properties of the PEGDMA/PLA mixtures, and on the degree of methacrylate vinyl conversion (DC), as well as blend miscibility, microstructure, mechanical properties, in vitro swelling behavior, and cell responses were studied. PLA-2K (molecular mass: 2096 g/mol) and PLA-63K (molecular mass: 63 000 g/mol) formed miscible and partially miscible blends with cross-linked PEGDMA, respectively. The addition of the PLA-2K did not affect the immediate or post-cure (>24 h) DC of the PEGDMA upon photopolymerization. However, the addition of PLA-63K decreased the immediate DC of the PEGDMA, which can be increased through extending the curing time or post-curing period. Compared to the cross-linked neat PEGDMA and PLA-2K/PEGDMA blends, PLA-63K/PEGDMA blends were significantly stronger, stiffer, and tougher. Both types of blends and the cross-linked PEGDMA swelled when soaked in a phosphate buffered saline (PBS) solution. The attachment and spreading of MCT3-E1 cells increased with increasing PLA-63K content in the blends. The facile and rapid formation of PEGDMA/PLA blends by photopolymerization represents a simple and efficient approach to a class of biomaterials with a broad spectrum of properties.     

Effect of recombinant Mce4A protein of Mycobacterium bovis on expression of TNF-α, iNOS, IL-6, and IL-12 in bovine alveolar macrophages

CD38 is a type II transmembrane protein with 25% of its molecular mass consisting of glycosyl moieties. It has long been predicted that the carbohydrate moieties of glycoproteins play important roles in the physical function and structural stability of the proteins on cell surfaces. To determine the structural/functional significance of glycosylation of the human CD38, the four potential N-linked glycosylation sites asparagine residues, N100, N164, N209 and N219 were mutated. The mutant (CD38mu) and wild-type (CD38wt) were expressed separately in Escherichia coli, HeLa, and MCF-7 cells. SDS-polyacrylamide gel electrophoresis under reducing conditions and western blotting indicated that the molecular mass of the CD38wt is 45 kDa, and that of the CD38mu is 34 kDa in HeLa cells. Importantly, the CD38mu protein expressed in HeLa cells, showed the high molecular weight oligomers in addition to the 34 kDa monomeric form. Similarly, in E. coli, the CD38wt formed dimers and other oligomers besides the monomeric form. Moreover, MCF-7 cells stably transfected with CD38wt cDNA, also revealed the presence of cross-linked oligomers when treated with a N-linked glycosylation inhibitor tunicamycin (TM). These results suggested that the N-linked glycosylation of CD38 plays a crucial role in the structure stability by preventing the formation inter-molecular cross-links. In addition, immunostaining, enzyme activity (cyclase), and western blotting data revealed that the glycosylation of human CD38 protein is not required for its localization to the cell membrane.     

Molecular dynamics and dissipative particle dynamics simulations for prediction of miscibility in polyethylene terephthalate/polylactide blends

The miscibility of polyethylene terephthalate (PET)/polylactide (PLA) blends is studied through atomistic molecular dynamics (MD) and mesoscale dissipative particle dynamics (DPD) simulation. Five PET/PLA blends (with the weight ratio at 90/10, 70/30, 50/50, 30/70 and 10/90) as well as pure PET and PLA are examined. The solubility parameter values obtained by using the MD simulation are in good agreement with the reference data. The Flory–Huggins parameters, χ, which are computed for different blends and determined from the cohesive energy densities, with the radial distribution functions g(r) of the inter-molecular atoms, suggest that PET is completely miscible with PLA over the entire composition range. This is further proved by the mesoscopic morphologies of PET/PLA blends. All the simulation results are qualitatively consistent with the experimental results, and demonstrate that the modelling strategies in this study may serve as a powerful tool for predicting miscibility and mesoscopic morphology of polymer blends.     

Engineering mouse apolipoprotein A-I into a monomeric, active protein useful for structural determination

Apolipoprotein AI (apoAI), the major protein component of HDL, is one of the best predictors of coronary artery disease (CAD), with high apoAI and HDL levels being correlated with low occurrences of CAD. The primary function of apoAI is to recruit phospholipid and cholesterol for assembly of HDL particles. Like other exchangeable apolipoproteins, lipid-free apoAI forms a mixture of different oligomers even at 1.0 mg/mL. This self-association property of the exchangeable apolipoproteins is closely associated with the lipoprotein-binding activity of this protein family. It is unclear if the self-association property of apolipoprotein is required for its lipoprotein-binding activity. We developed a novel method for engineering an oligomeric protein to a monomeric, biologically active protein. Using this method, we generated a monomeric mouse apoAI mutant that is active. This mutant contains the first 216 residues of mouse apoAI and replaces six hydrophobic residues with either polar or smaller hydrophobic residues at the defined positions (V118A/A119S/L121Q/T191S/T195S/T199S). Cross-linking results show that this mutant is greater than 90% monomeric at 8 mg/mL. CD, DSC, and NMR results indicate that the mutant maintains an identical secondary, tertiary structure and stability as those of the wild-type mouse apoAI. Lipid-binding assays suggest that the mutant shares an equal lipoprotein-binding activity as that of the wild-type apoAI. In addition, both the monomeric mutant and the wild-type protein make nearly identical rHDL particles. With this monomeric mouse apoAI, high-quality NMR data has been collected, allowing for the NMR structural determination of lipid-free apoAI. On the basis of these results, we conclude that this apoAI mutant is a monomeric, active apoAI useful for structural determination.     

A study of conformational stability of polyglycine and poly(L-alanine), and polyglycine/poly(L-alanine) blends in the solid state by (13)C cross-polarization/magic angle spinning NMR

13C Cross-Polarization/Magic Angle Spinning nmr and T(1rhoH) experiments of polyglycine (PG), poly(L-alanine) (PLA), and PG/PLA blends prepared from dichloroacetic acid solution have been carried out, in order to elucidate the conformational stability of these polypeptides in the solid state. From these experimental results, it was clarified that the conformations of PG and PLA in their blends are strongly influenced by intermolecular hydrogen-bonding interactions that cause their miscibility at the molecular level.     

Lignin-polymer blends: evaluation of compatibility by image analysis

This paper opens onto a general discussion on the development of new polymeric materials obtained from lignin blends. The aim is (i) to look for good polymer candidates to obtain a good compatibility with lignins (that is among semi polar polymers), and (ii) to look for good lignin candidates to obtain a good compatibility with polymers showing extreme behaviours (very polar, e.g. starch, or apolar, e.g. polypropylene). The compatibility is simply assessed through the blend morphology, as studied by visible microscopy. The morphology of the blends obtained from semi polar polymers is very sensitive to the variation of the solubility parameters. In a low range of polymer solubility parameters (delta delta = 1 cal cm(-3)), both heterogeneous and homogeneous systems are obtained. These blends could be easily improved by a careful choice in the polymer structure (particularly in the family of biodegradable polyesters); it could be possible also to take advantage of lignin variability to improve the compatibility. Only low molecular weight lignins are compatible with apolar and very polar matrixes. These compounds induce interesting specific properties, and original methods have to be looked for in order to improve their production.     

Synthesis and properties of star-shaped polylactide attached to poly(amidoamine) dendrimer

Star-shaped polylactide was synthesized by bulk polymerization of lactide with poly(amidoamine) (PAMAM) dendrimer as initiator, which was marked as PAMAM-g-PLA for simplicity. The nonlinear architecture of PAMAM-g-PLA was confirmed by gel permeation chromatograph, nuclear magnetic resonance, and differential scanning calorimetry analysis. Unlike the linear polylactide (PLA) with similar molecular weight, PAMAM-g-PLA had a higher hydrophilicity and a faster degradation rate because of shortened polymer chains and increased polar terminal endgroups due to its branch structure. The highly branched structure significantly accelerated the release of water-soluble bovine serum albumin from PAMAM-g-PLA microspheres, whereas the linear PLA with similar molecular weight exhibited an initial time lag release. This star polymer may have potential applications for hydrophilic drug delivery in tissue engineering, including growth factor and antibodies to induce tissue regeneration, by adjusting the chain lengths of PLA branches.     

The lipid peroxidation metabolite 4-oxo-2-nonenal cross-links α-synuclein causing rapid formation of stable oligomers

Recently, the aldehyde 4-oxo-2-nonenal (ONE) was identified as a product of lipid peroxidation and found to be an effective protein modifier. In this in vitro study we investigated structural implications of the interaction between ONE and α-synuclein, a protein which forms intraneuronal inclusions in neurodegenerative disorders such as Parkinson’s disease and dementia with Lewy bodies. Our results demonstrate that ONE induced an almost complete conversion of monomeric α-synuclein into 40-80 nm wide and 6-8 nm high soluble β-sheet-rich oligomers with a molecular weight of ∼2000 kDa. Furthermore, the ONE-induced α-synuclein oligomers displayed a high stability and were not sensitive to treatment with sodium dodecyl sulfate, indicating that ONE stabilized the oligomers by cross-linking individual α-synuclein molecules. Despite prolonged incubation the oligomers did not continue to aggregate into a fibrillar state, thus suggesting that these α-synuclein species were not on a fibrillogenic pathway.     

新型共聚物淀粉接技聚乳酸的制备及其表征

采用原位熔融共聚法,以淀粉和乳酸为原料,制备改性淀粉聚乳酸接枝共聚物,对共聚反应机理进行初步探讨.结果表明,淀粉经PEG-400和马来酸酐增塑改性处理反应活性增强,与乳酸反应生成的淀粉聚乳酸接枝共聚物分子量Mw为6.921×10~4,Mn为4.789×10~4,分子量分布Mw/Mn为1.445.共聚物在PBS缓冲溶液中进行降解测试,结果为6天后质量损失一半.     

Conformational changes and protein stability of the pro-apoptotic protein Bax

Pro-apoptotic Bax is a soluble and monomeric protein under normal physiological conditions. Upon its activation substantial structural rearrangements occur: The protein inserts into the mitochondrial outer membrane and forms higher molecular weight oligomers. Subsequently, the cells can undergo apoptosis. In our studies, we focused on the structural rearrangements of Bax during oligomerization and on the protein stability. Both protein conformations exhibit high stability against thermal denaturation, chemically induced unfolding and proteolytic processing. The oligomeric protein is stable up to 90 °C as well as in solutions of 8 M urea or 6 M guanidinium hydrochloride. Helix 9 appears accessible in the monomer but hidden in the oligomer assessed by proteolysis. Tryptophan fluorescence indicates that the environment of the C-terminal protein half becomes more apolar upon oligomerization, whereas the loop region between helices 1 and 2 gets solvent exposed.     

Characterization of human small heat shock protein HspB1 that carries C-terminal domain mutations associated with hereditary motor neuron diseases

Physico-chemical properties of four mutants (T164A, T180I, P182S and R188W) of human small heat shock protein HspB1 (Hsp27) associated with neurodegenerative diseases were analyzed by means of fluorescence spectroscopy, dynamic light scattering, size-exclusion chromatography and measurement of chaperone-like activity. Mutation T164A was accompanied by destabilization of the quaternary structure and decrease of thermal stability without any significant changes of chaperone-like activity. Mutations T180I and P182S are adjacent or within the conserved C-terminal motif IPI/V. Replacement T180⇒I leading to the formation of hydrophobic cluster consisting of three Ile produced small increase of thermal stability without changes of chaperone-like activity. Mutation P182S induced the formation of metastable large oligomers of HspB1 with apparent molecular weight of more than 1000 kDa. Oligomers of P182S have very low thermal stability and undergo irreversible aggregation at low temperature. The P182S mutant forms mixed oligomers with the wild type HspB1 and the properties of these mixed oligomers are intermediate between those of the wild type HspB1 and its mutant. Mutation R188W did not significantly affect quaternary structure or thermal stability of HspB1, but was accompanied by a pronounced decrease of its chaperone-like activity. All mutations analyzed are associated with hereditary motor neuropathies or Charcot–Marie–Tooth disease type 2; however, molecular mechanisms underlying pathological effects are specific for each of these mutants.     

Stabilization,Characterization, and Selective Removal of Cystatin C Amyloid Oligomers

The pathophysiological process in amyloid disorders usually involves the transformation of a functional monomeric protein via potentially toxic oligomers into amyloid fibrils. The structure and properties of the intermediary oligomers have been difficult to study due to their instability and dynamic equilibrium with smaller and larger species. In hereditary cystatin C amyloid angiopathy, a cystatin C variant is deposited in arterial walls and cause brain hemorrhage in young adults. In the present investigation, we use redox experiments of monomeric cystatin C, stabilized against domain swapping by an intramolecular disulfide bond, to generate stable oligomers (dimers, trimers, tetramers, decamers, and high molecular weight oligomers). These oligomers were characterized concerning size by gel filtration, polyacrylamide gel electrophoresis, and mass spectrometry, shape by electron and atomic force microscopy, and, function by assays of their capacity to inhibit proteases. The results showed the oligomers to be highly ordered, domain-swapped assemblies of cystatin C and that the oligomers could not build larger oligomers, or fibrils, without domain swapping. The stabilized oligomers were used to induce antibody formation in rabbits. After immunosorption, using immobilized monomeric cystatin C, and elution from columns with immobilized cystatin C oligomers, oligomer-specific antibodies were obtained. These could be used to selectively remove cystatin C dimers from biological fluids containing both dimers and monomers.     

Eudragit L/HPMCAS Blend Enteric-Coated Lansoprazole Pellets: Enhanced Drug Stability and Oral Bioavailability

The objectives of the present work were to use blends of Eudragit L and hydroxypropyl methylcellulose acetate succinate (HPMCAS) as enteric film coatings for lansoprazole (LSP) pellets. The enteric-coated pellets were prepared with a fluid-bed coater. The influence of the blend ratio, type of plasticizer, plasticizer level, coating level, and curing conditions on gastric stability in vitro drug release and drug stability was evaluated. Furthermore, the bioavailability of the blend-coated pellets in beagle dogs was also performed. The blend-coated pellets exhibited significant improvement of gastric stability and drug stability compared to the pure polymer-coated pellets. Moreover, the AUC values of blend-coated pellets were greater than that of the pure polymer-coated pellets. It was concluded that the using blends of Eudragit L and HPMCAS as enteric film coatings for LSP pellets improved the drug stability and oral bioavailability.     

Poly(l-lactide) degradation by Kibdelosporangium aridum

A new poly(L-lactide) (PLA)-degrading actinomycete, Kibdelosporangium aridum, degraded more than 97 mg out of 100 mg added high molecular weight PLA film (Mn: 3.4 x 10(5)) within 14 d in liquid culture. L-Lactic acid, the monomeric degradation product of PLA, was totally assimilated by the strain. In solid culture, many distinct grooves formed by the morphology of filamentous microorganisms on the surface of a PLA film were observed by scanning electron microscopy.     

Sulfated glycosaminoglycans accelerate transthyretin amyloidogenesis by quaternary structural conversion

Glycosaminoglycans (GAGs), which are found in association with all extracellular amyloid deposits in humans, are known to accelerate the aggregation of various amyloidogenic proteins in vitro. However, the precise molecular mechanism(s) by which GAGs accelerate amyloidogenesis remains elusive. Herein, we show that sulfated GAGs, especially heparin, accelerate transthyretin (TTR) amyloidogenesis by quaternary structural conversion. The clustering of sulfate groups on heparin and its polymeric nature are essential features for accelerating TTR amyloidogenesis. Heparin does not influence TTR tetramer stability or TTR dissociation kinetics, nor does it alter the folded monomer-misfolded monomer equilibrium directly. Instead, heparin accelerates the conversion of preformed TTR oligomers into larger aggregates. The more rapid disappearance of monomeric TTR in the presence of heparin likely reflects the fact that the monomer-misfolded amyloidogenic monomer-oligomer-TTR fibril equilibria are all linked, a hypothesis that is strongly supported by the light scattering data. TTR aggregates prepared in the presence of heparin exhibit a higher resistance to trypsin and proteinase K proteolysis and a lower exposure of hydrophobic side chains comprising hydrophobic clusters, suggesting an active role for heparin in amyloidogenesis. Our data suggest that heparin accelerates TTR aggregation by a scaffold-based mechanism, in which the sulfate groups comprising GAGs interact primarily with TTR oligomers through electrostatic interactions, concentrating and orienting the oligomers, facilitating the formation of higher molecular weight aggregates. This model raises the possibility that GAGs may play a protective role in human amyloid diseases by interacting with proteotoxic oligomers and promoting their association into less toxic amyloid fibrils.