Removal of copper using marine brown alga, Undaria Pinnatifida modified with oxime

Summary As oxime is selective for Cu²⁺, oxime groups were introduced to the cell wall of alga by glutaraldehyde. Such modified biomass showed high affinity for Cu²⁺, which resulted in the increase of copper sorption capacity about 4.5 times higher than that of natural alga. For pH range from 2.5 to 3.0, only Cu²⁺ were removed by alga biomass modified with oxime, while other heavy metal ions such as Ca²⁺,Cd²⁺,Pb²⁺ were not adsorbed. By changing pH, selective recovery of Cu²⁺ was achieved.     

Removal of Cd2+, Pb2+, and Zn2+ from contaminated water using dolomite powder

Dolomite collected from Surat Thani Province in Thailand was investigated for use as a sorbent for the removal of divalent heavy metal cations from an aqueous solution. The sorbent had a surface area of 2.46 m²/g and a pH of zero point charge (pHzpc) of 9.2. Batch sorption was used to examine the effect of the pH (pH 3–7) on the sorption capacity of Cd²⁺, Pb²⁺ and Zn²⁺, alone or together as an equimolar mixture at various concentrations. Alone, each heavy metal cation was adsorbed faster at a higher pH, where the sorption of Cd²⁺ and Pb²⁺ fitted a Langmuir isotherm, but Zn²⁺ sorption best fitted a Freundlich isotherm. Under equimolar competitive sorption, the sorption capacity of each cation was decreased by 75.8% (0.29–0.07 mM/g), 82.8% (0.53–0.09 mM/g), and 95.7% (0.84–0.04 mM/g) for Cd²⁺, Pb²⁺ and Zn²⁺, respectively, compared to that with the respective single cation. Desorption of these heavy metal cations from dolomite was low, with an average desorption level of 0.06–17.4%. Furthermore, since dolomite is readily available and rather cheap, it is potentially suitable for use as an efficient sorbent to sorb Cd²⁺ and Pb²⁺, and perhaps Zn²⁺, from contaminated water.     

Studies of biosorption of Pb2+, Cd2+ and Cu2+ from aqueous solutions using Adansonia digitata root powders

The potentials of Adansonia digitata root powders (ADRP) for adsorption of Pb²⁺, Cd²⁺ and Cu²⁺ from aqueous solutions was investigated. Physico-chemical analysis of the adsorbent (ADRP) shows that hydroxyl, carbonyl and amino groups were predominant on the surface of the adsorbent. Scanning Electron Microscope (SEM) image revealed its high porosity and irregular pores in the adsorbent while the Energy Dispersive X-ray Spectrum showed the major element with 53.0% Nitrogen, 23.8% carbon, 9.1% calcium, 7.5% potassium and 6.6% magnesium present. The found optimal conditions were: initial concentration of the metal ions = 0.5 mg/L, pH = 5, contact time = 90 min, adsorbent dose = 0.4 g and particle size = 32 µm. Freundlich isotherm showed good fit for the adsorption of Pb²⁺, Cd²⁺ and Cu²⁺. Dubinin-Radushkevich isotherm revealed that the adsorption processes were physisorption Cd(II) and Cu(II) but chemisorption with respect to Pb(II) ions. The kinetics and thermodynamic studies showed that Pseudo-second order and chemisorptions provided the best fit to the experimental data of Pb (II) ions only. Batch desorption result show that desorption in the acidic media for the metal ions were more rapid and over 90% of the metal ions were recovered from the biomass.     

Multi-metal biosorption and bioaccumulation by Exiguobacterium sp. ZM-2

The present work deals with the biosorption performance of dried and non-growing biomasses of Exiguobacterium sp. ZM-2, isolated from soil contaminated with tannery effluents, for the removal of Cd²⁺, Ni²⁺, Cu²⁺, and Zn²⁺ from aqueous solution. The metal concentrations studied were 25 mg/l, 50 mg/l, 100 mg/l, 150 mg/l and 200 mg/l. The effect of solution pH and contact time was also studied. The biosorption capacity was significantly altered by pH of the solution. The removal of metal ions was conspicuously rapid; most of the total sorption occurred within 30 min. The sorption data have been analyzed and fitted to the Langmuir and Freundlich isotherm models. The highest Q_max value was found for the biosorption of Cd²⁺ at 43.5 mg/g in the presence of the non-growing biomass. Recovery of metals (Cd²⁺, Zn²⁺, Cu²⁺ and Ni²⁺) was found to be better when dried biomass was used in comparison to non-growing biomass. Metal removal through bioaccumulation was determined by growing the bacterial strain in nutrient broth amended with different concentrations of metal ions. This multi-metal resistant isolate could be employed for the removal of heavy metals from spent industrial effluents before discharging them into the environment.     

Toxic metal biosorption by macrocolonies of cyanobacterium <Emphasis Type="Italic">Nostoc sphaeroides</Emphasis> Kützing

The cyanobacterium Nostoc sphaeroides Kützing is expected to be effective in toxic metal adsorption as it produces abundant exopolysaccharides with functional groups. Therefore, the adsorption properties of Cu²⁺, Cd²⁺, Cr³⁺, Pb²⁺, Ni²⁺, and Mn²⁺ on fresh macrocolonies and algal powder of N. sphaeroides were compared at pH 5 and 25 °C. The adsorption capacity of fresh biomass for Pb²⁺ and of algal powder for Pb²⁺ and Cr³⁺ were highest in single metal solutions. Compared to the fresh biomass, the metal adsorption capacities of algal powder were similar for Ni²⁺, Cd²⁺, and Pb²⁺ and slightly greater for Cr³⁺, but they were markedly smaller for Mn²⁺ and Cu²⁺. Coexisting ions (in tap water or in multiple solutions) significantly decreased the metal adsorption capacity, except for Cr³⁺ in tap water. The Pb²⁺ and Cr³⁺ adsorption dynamic process fitted the pseudo-second-order model well, showing fast adsorption at the first stage in 10 and 20 min, respectively. Higher pH in acidic ranges favored the adsorption greatly. The Langmuir isotherm model was suitable for explaining the adsorption, and the maximum adsorption capacities were 116.28 and 22.37 mg g^?1 for Pb²⁺ and Cr³⁺, respectively. The adsorption process was endothermic, confirmed by the significantly higher adsorption capability at higher temperature. Hydroxyl, amino, and carboxyl groups were the main functional groups based on Fourier transform infrared spectroscopy analysis, and they bind to metal ions via ion exchange. The results suggest that fresh macrocolonies of N. sphaeroides can be used as an effective biosorbent for metal ion removal, especially for Pb²⁺ and Cr³⁺.     

Oscillatoria anguistissima: A Promising Cu2+ Biosorbent

Oscillatoria anguistissima rapidly adsorbs Cu²⁺ from aqueous solution. The adsorption of Cu²⁺ followed Freundlich Isotherm, and the amount of Cu²⁺ removed from solution increased with increasing Cu²⁺ concentration. The adsorption is pH dependent, and maximum Cu²⁺ removal occurs at pH 5. Of the various pretreatments, HCl treatment of the biomass increased the capacity for Cu²⁺ removal. Presence of Mg²⁺ and Ca²⁺ resulted in decline in the Cu²⁺ adsorption capacity of Oscillatoria cells. This species could also effectively remove Cu²⁺ from mine water containing 68.4 μg/ml of Cu²⁺ at pH 3.45. Received: 23 December 1996 / Accepted: 20 February 1997     

POTENTIAL USE OF LEAF BIOMASS,ARAUCARIA HETEROPHYLLA FOR REMOVAL OF Pb+2

The present investigation attempt to analyze the biosorption behavior of novel biosorbent, Araucaria heterophylla (green plant) biomass, for removal of Pb⁺² from solution as the function of initial metal ion concentration, pH, temperature, sorbent dosage and biomass particle size. The maximum biosorption was found to be 95.12% at pH 5 and biosorption capacity (q_e) of Cd⁺² is 9.643 mg/g. The Langmuir and Freundlich equilibrium adsorption isotherms were studied and observed that Freundlich model is best fit than the Langmuir model with correlation coefficient of 0.9927. Kinetic studies indicated that the biosorption process of Cd⁺² followed well pseudo second order model with R² 0.999. The process is exothermic and, spontaneous. The chemical functional groups –OH, CH₂ stretching vibrations, C?O of alcohol, C?O of amide, P?O stretching vibrations, –CH, were involved in the process. The XRD pattern of the A. heterophylla was found to be mostly amorphous in nature. The SEM studies showed Pb⁺² biosorption on selective grains of the biosorbent. It was concluded that A. heterophylla leaf powder can be used as an effective, low cost, and environmentally friendly biosorbent for the removal of Pb⁺² from aqueous solution.     

Removal of heavy metals from aqueous solution by common freshwater filamentous algae

Non-living (dried) biomass of five common filamentous algae belonging to Chlorophyta and Cyanophyta (Cyanobacteria) were screened for their metal ion sorption and removal efficiency in a batch system. A considerably higher magnitude of sorption of Pb²⁺ and Cu²⁺ by all the tested algae suggests the prevalence of Pb²⁺- and Cu²⁺-binding ligands in them. The Langmuir isotherm could more appropriately describe metal sorption by the test algae than the Freundlich isotherm. A 1 g l⁻¹ biomass concentration of Pithophora odeogonia and Spirogyra neglecta, respectively removed 97 and 89% Pb²⁺in 30 min from a solution containing 5 mg l⁻¹ initial concentration of Pb²⁺. Metal ion removal by the test algae decreased with increase in metal concentration in the solution. S. neglecta could remove >70% Pb²⁺ even from a solution containing 75 mg Pb²⁺ l⁻¹. S. neglecta and P. oedogonia could remove more than 75% of Pb²⁺ and Cu²⁺ from a multi-metal solution, and therefore have tremendous potential for removing Pb²⁺and Cu²⁺ from wastewaters containing several metal ions simultaneously. Other test algae, namely, Hydrodictyon reticulatum, Cladophora calliceima and Aulosira fertilissima were relatively less efficient in removing metal ions from solution.     

Metal resistance and removal by two strains of the green alga, <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> Beijerinck,isolated from Laguna de Bay,Philippines

Two strains of Chlorella vulgaris Beijerinck isolated from two different sites in Laguna de Bay, Philippines, were studied for their resistance and ability to remove four metal ions, i.e., Cu²⁺, Cr⁶⁺, Pb²⁺, and Cd²⁺ added separately in BG-11 growth medium. The growth of the two strains was severely inhibited at 2 mg.L⁻¹ of Cu²⁺, 5 mg.L⁻¹ of Cr⁶⁺, 8 mg.L⁻¹ of Pb²⁺, and 10 mg.L⁻¹ of Cd²⁺. However, the two strains exhibited different EC₅₀ values for the same metal ion. The WB strain had a significantly higher resistance (p < 0.01) for Cd²⁺ and Cr⁶⁺ compared with the SB strain, while the SB strain had significantly higher resistance (p < 0.01) for Cu²⁺ compared with the WB strain. On the other hand, the two strains behaved differently in their capacity to remove the metal ions in BG-11 medium containing 1.0 mg.L⁻¹ of the three metal ions, except for Cu²⁺, which was added at 0.1 mg.L⁻¹. The WB strain showed the highest removal of Cd²⁺ at 70.3% of total, followed by Pb²⁺ at 32%, while the SB strain exhibited the highest removal of Pb²⁺ at 48.7% followed by Cd²⁺ at 40.7% of the total. Both strains showed the least removal of Cr⁶⁺ at 28% and 20.8% of the total for the WB and SB strains respectively. The percentage removal for Cu²⁺ was 50.7% and 60.8% for the WB and SB strains respectively. After 12 days of incubation, both strains showed that a greater percentage of the metal ions removed were accumulated intracellularly than adsorbed at a ratio of at least 2:1. Both strains manifested the same cytological deformities, like a loss of pyrenoids at 10 mg.L⁻¹ in all four metal ions. Discoloration and disintegration of chloroplasts were observed at 1.0 mg.L⁻¹ in Cu²⁺ and 5 mg.L⁻¹ in Cr⁶⁺. The nonrelease of autospores from the mother cells was observed at 10 mg.L⁻¹ in Cu²⁺ and Cr⁶⁺. Presented at the 6th Meeting of the Asian Pacific Society of Applied Phycology, Manila, Philippines.     

Biosorption of heavy metal ions by brown seaweeds from southern coast of Korea

Heavy metal ions (Pb²⁺, Cd²⁺, Mn²⁺, Cu²⁺, and Cr₂O₇ ^2?) were biosorbed by brown seaweeds (Hizikia fusiformis, Laminaria japonica, and Undaria pinnatifida) collected from the southern coast of South Korea. The biosorption of heavy metal ions was pH-dependent showing a minimum absorption at pH 2 and a maximum biosorption at pH 4 (Pb²⁺, Cd²⁺, Mn²⁺, and Cr₂O₇ ^2?) or pH 6 (Cu²⁺). Biosorption increased most noticeably for pH changes from 2 to 3. In the latter pH range, biosorption increased, because a higher pH decreased the electrostatic repulsion between metal ions and functional groups on the seaweed. In the pH range of 2 ～ 4, biosorption of negatively-charged chromium species (Cr₂O₇ ^?2) followed the pattern of positively-charged metal ions (Pb²⁺, Cd²⁺, Mn²⁺, and Cu²⁺). This suggests that the most prevalent chromium species were positively-charged Cr³⁺, reduced from Cr⁶⁺ in Cr₂O₇ ^?2. Whereas positively-charged heavy metal ions (Pb²⁺, Cd²⁺, Mn²⁺, and Cu²⁺) reached a plateau after the maximum level, biosorption of chromium ions decreased noticeably between pH 5 and 8. Kinetic data showed that biosorption by brown seaweed occurred rapidly during the first 10 min, and most of the heavy metals were bound to the seaweed within 30 min. Equilibrium adsorption data for a lead ion could fit well in the Langmuir and Freundlich isotherm models with regression coefficients (R ²) between 0.93 and 0.98.     

Effect of calcium chloride on heavy metal induced alteration in growth and nitrate assimilation of Sesamum indicum seedlings

In the early growth phase of Sesamum indicum cv. PB-1, the decrease in fresh and dry mass was higher with 1.0 mM Cd²⁺ than with the same level of Pb²⁺ and Cu²⁺. Recovery from the metal stress was considerable in the root fresh weight and almost completely in the root dry weight when 10.0 mM (1.9 EC), calcium chloride was supplied to the growing seedlings along with the metal salts in various combinations. Accumulation of Pb²⁺, Cd²⁺ and Cu²⁺ was differential to the metals and the plant parts when supplied without or with 10.0 mM calcium chloride. The order of endogenous metal accumulation was Cu²⁺Cd²⁺Pb²⁺ and roots accumulated more metal than the leaves in the absence, as well as in the presence, of calcium chloride. Calcium chloride could recover loss of in vivo NRA in roots caused by either of the metal combinations, whereas the salt could recover the loss in leaf NRA caused only by Pb²⁺Cd²⁺ (1.0 mM each). Response of root and leaf NRA was on the other hand, different when the enzyme was assayed directly using an in vitro assay method, and the salt accelerated the loss in enzyme activity drastically. The organic-N content of root and leaf was, however, increased significantly (p < 0.001) with calcium chloride alone and with the metals supplied in various combinations. Our data indicate that instead of a high endogenous accumulation of Cu²⁺, Cd²⁺ and Pb²⁺ in roots and leaves the metal toxicity is recovered to a great extent in the presence of 10.0 mM calcium chloride in the root environment regarding growth and nitrate reduction of the roots and leaves of young sesame seedlings.     

OPTIMIZATION OF SOME HEAVY METALS BIOSORPTION BY REPRESENTATIVE EGYPTIAN MARINE ALGAE1

Marine algae—as inexpensive and renewable natural biomass—have attracted the attention of many investigators to be used to preconcentrate and biosorb many heavy metal ions. Impressed by this concept, the metal uptake capacity of Egyptian marine algae was examined using representatives of green and brown algae, namely, Ulva lactuca L. and Sargassum latifolium (Turner) C. Agardh, respectively. The biosorption efficiencies of Cu²⁺, Co²⁺, Ni²⁺, Cd²⁺, Hg²⁺, Ag²⁺, and Pb²⁺ ions seem to depend on the type of the algae used as well as the conditions under which the uptake processes were conducted. It was demonstrated that a pH range of 7.5–8.8 was optimum for the removal of the tested metals. Similarly, the uptake process was markedly accelerated during the first 2 h using relatively low metal level and sufficient amounts of the dried powdered tested algae.     

Optimization of flow rate,initial metal ion concentration and biomass density for maximum removal of Cu2+ by immobilized Microcystis

The potential of alginate-immobilized Microcystis packed in a column for maximum removal of Cu²⁺ at different flow rates, biomass, and initial metal ion concentration was assessed in a continuous flow system. Although Cu²⁺ removal did occur at all the flow rates tested, it was maximum (54%) at 0.75-ml min⁻¹ flow rate, 30 μg ml⁻¹ initial metal ion concentration and 0.016 g biomass. Cu²⁺ removal was influenced by inlet metal ion concentration and biomass density. An increase in the biomass concentration from 0.016 to 0.128 g resulted in an apparent increase in percentage removal but the Cu²⁺ adsorbed per unit dry wt. declined. When the flow rate (0.75 ml min⁻¹) and biomass density (0.064 g) were kept constant and the inlet metal ion concentration was varied from 10 to 150 μg ml⁻¹, a 68% removal of Cu²⁺ was obtained at 50 μg ml⁻¹ initial concentration in a time duration of 15 min. The metal-laden columns were efficiently desorbed and regenerated following elution with double distilled water (DDW) (pH 2) (89%). This was followed by 1 mm EDTA > 1 mm NTA > 0.1 mm EDTA > 1 mm HCl > 1 mm HNO₃ > 5 mm CaCl₂ > DDW (pH 7.0) > 1 mm NaHCO₃ > 1 mm CaCl₂. Of the total (2.83 mg) adsorbed Cu²⁺, 1.89 mg (67%) was desorbed by DDW (pH 2) within the first 20 min of elution time. Thereafter the desorption rate slowed down and only 22% (0.632 mg) desorption was obtained in the last 20 min. In contrast to water pH 2, the desorption of Cu²⁺ by 1 mm EDTA was very slow, the maximum being 8% after 40 min of elution. This revised version was published online in July 2006 with corrections to the Cover Date.     

Uptake of Metal Ions by Rhizopus arrhizus Biomass

Rhizopus arrhizus biomass was found to absorb a variety of different metal cations and anions but did not absorb alkali metal ions. The amount of uptake of the cations was directly related to ionic radii of La³⁺, Mn²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Ba²⁺, Hg²⁺, Pb²⁺, UO₂²⁺, and Ag⁺. The uptake of all the cations is consistent with absorption of the metals by sites in the biomass containing phosphate, carboxylate, and other functional groups. The uptake of the molybdate and vanadate anions was strongly pH dependent, and it is proposed that the uptake mechanism involves electrostatic attraction to positively charged functional groups.     

Stability of Ca2+-, Cd2+-, Cu2+-[illite-humic] complexes and pH influence

Decomposition of fresh plant residues in soil is expected to produce humic fractions varying in molecular size. It was hypothesized that metal adsorption by soil, to some degree, will depend on humic acid content and molecular size. The latter is expected to vary in number and type of functional groups. In this study, illite-humic complexes were used to evaluate Ca²⁺, Cd²⁺, and Cu²⁺ adsorption and how this adsorption was affected by humic acids, differing in molecular size, under various pH values. Potentiometric titration using ion-selective electrodes with a stop-and-go procedure was employed to evaluate metal-[illite-humic] complex formation. The results showed that illite-humic complexes exhibited at least two types of metal-ion adsorption sites (low and high affinity) and molecular size of humic fractions had a large potential influence on total metal adsorption but a relatively smaller influence on metal-complex stability. Relative strength of metal-ion-[illite-humic] complexes followed the order of Cu²⁺>Cd²⁺>Ca²⁺ and were affected by pH, especially for low metal-ion affinity sites. Magnitude of metal-[illite-humic] stability constants, depending on molecular size of humic fraction and pH, varied on a log-scale from 3.52 to 4.21 for Ca²⁺, 4.38 to 5.18 for Cd²⁺and from 5.23 to 5.83 for Cu²⁺. There was an approximate 5-fold difference in these stability constants between the three different sizes of humic fractions. The larger the humic fraction, the lower the metal-[illite-humic] stability constant. This revised version was published online in June 2006 with corrections to the Cover Date. This revised version was published online in June 2006 with corrections to the Cover Date. This revised version was published online in June 2006 with corrections to the Cover Date.     

Use of the microalga Scenedesmus obliquus to remove cadmium cations from aqueous solutions

The ability of a wild strain of Scenedesmus obliquus, isolated from a heavy metal-contaminated environment, to remove Cd²⁺ from aqueous solutions was studied at several initial concentrations. Viable biomass removed metal to a maximum extent of 11.4 mg_Cd/g at 1 mg_Cd/l, with most Cd²⁺ being adsorbed onto the cell surface. A commercially available strain (ACOI 598) of the same microalga species was also exposed to the same Cd concentrations, and similar results were obtained for the maximum extent of metal removal. Heat-inactivated cells removed a maximum of 6.04 mg_Cd/g at 0.5 mg_Cd/l. The highest extent of metal removal, analyzed at various pH values, was 0.09 mg_Cd/g at pH 7.0. Both strains of the microalga tested have proven effective in removing a toxic heavy metal from aqueous solutions, hence supporting their choice for bioremediation strategies of industrial effluents.     

Cd2+和Pb2+对花翅摇蚊(Chironomus kiiensis)幼虫生长发育的影响及富集效应

河流、湖泊等水生环境中普遍存在的重金属污染破坏水生生态系统并间接威胁人类健康。为探究重金属胁迫下水生昆虫花翅摇蚊（Chironomus kiiensis）生态毒理,测定了重金属Cd²⁺和Pb²⁺胁迫对花翅摇蚊化蛹率和羽化率的影响,检测了摇蚊的口器致畸与富集效应。研究结果表明,Cd²⁺和Pb²⁺影响摇蚊幼虫化蛹和羽化过程,单一重金属离子处理14 d Pb²⁺处理组的化蛹率和羽化率分别为22.22%和8.89%,低于Cd²⁺的化蛹率（25.56%）和羽化率（11.11%）,表现出更强的抑制效应。混合离子1：2和2：1配比处理组化蛹率和羽化率均为11.11%和4.44%,显著低于单一重金属离子胁迫下的化蛹率和羽化率。单一重金属离子及混合离子处理均能导致花翅摇蚊幼虫口器致畸,表现为上颚前齿断裂,中齿和基齿磨损、缺失,下唇板齿部不规则,下唇板边缘齿与中央齿磨损、断裂、增生、缺失。不同重金属离子处理下幼虫口器致畸率不同,并与暴露时间呈正相关,其中1：2配比处理14 d致畸率达到40.61%。重金属离子在摇蚊幼虫体内产生生物富集效应,单一重金属离子处理下的Pb²⁺富集含量7 d至14 d由11.46 mg/kg上升至31.32 mg/kg,不同配比混合离子处理下Pb²⁺富集含量均呈增加趋势,其中1：2配比处理组由15.48 mg/kg上升至42.50 mg/kg,而Cd²⁺在单一重金属与1：1混合离子处理组7 d至14 d的富集含量无显著性变化,2：1配比处理组由14.20 mg/kg下降至9.52 mg/kg,1：2配比由5.85 mg/kg上升至20.99 mg/kg。这些研究结果表明Cd²⁺和Pb²⁺胁迫影响花翅摇蚊幼虫生长发育且口器出现畸型,与重金属在幼虫体内的富集密切相关,为研究重金属对水生生态系统多重效应提供了理论依据。     

Enhanced sorption of Cu2+ and Ni2+ by acid-pretreated Chlorella vulgaris from single and binary metal solutions

The influence of HCl pretreatment (0.1 mM) on sorption ofCu²⁺ and Ni²⁺ by Chlorella vulgariswas tested using single and binary metal solutions. The optimal initial pH forsorption was 3.5 for Cu²⁺ and 5.5 for Ni²⁺. Second orderrate kinetics described well sorption by untreated and acid-pretreated cells.The kinetic constant q_e (metal sorption at equilibrium) for sorptionof test metals from single and binary metal solutions was increased afterpretreatment of the biomass with HCl. The Langmuir adsorption isotherm wasdeveloped for describing the various results for metal sorption. In single metalsolution, acid pretreatment enhanced q_max for Cu²⁺ andNi²⁺ sorption by approximately 70% and 65%, respectively.Cu²⁺ and Ni²⁺ mutually interfered with sorption of theother metal in the binary system. The combined presence of Cu²⁺ andNi²⁺ led to their decreased sorption by untreated biomass by 19% and88%, respectively. However, acid-pretreated biomass decreased Cu²⁺and Ni²⁺ sorption by 15 and 22%, respectively, when both the metalswere present in the solution. The results suggest a reduced mutual interferencein sorption of Cu²⁺ and Ni²⁺ from the binary metal systemdue to the acid pretreatment. Acid-pretreated cells sorbed twice the amount ofCu²⁺ and ten times that of Ni²⁺ than the untreated biomassfrom the binary metal system. Acid pretreatment more effectively enhanced thesorption of Ni²⁺ form the binary metal solution. The total metalsorption by untreated and acid-pretreated biomass depended on theCu²⁺ : Ni²⁺ ratio in the binary metal system. Acidpretreatment of C. vulgaris could be an effective andinexpensive strategy for enhancing Cu²⁺ and Ni²⁺ sorptionfrom single and binary metal solutions.     

Optimization of Cd2+ removal by the cyanobacterium Synechocystis pevalekii using the response surface methodology

Response surface methodology (RSM) has been used to optimize the critical parameters responsible for higher Cd²⁺ removal by a unicellular cyanobacterium Synechocystis pevalekii. A three-level Box–Behnken factorial design was used to optimize pH, biomass and metal concentration for Cd²⁺ removal. A coefficient of determination (R²) value (0.99), model F-value (86.40) and its low p-value (F < 0.0001) along with lower value of coefficient of variation (5.61%) indicated the fitness of response surface quadratic model during the present study. At optimum pH (6.48), biomass concentration (0.25 mg protein ml^?1) and metal concentration (5 μg ml^?1) the model predicted 4.29 μg ml^?1 Cd²⁺ removal and experimentally, 4.27 μg ml^?1 Cd²⁺ removal was obtained.     

Removal of cadmium by Pleurotus sajor-caju basidiomycetes

The bioaccumulation of cadmium by the white rot fungus Pleurotus sajor-caju onto dry biomass was investigated using aqueous media with concentrations in the range of 0.125 mM–1.0 mM The highest cadmium uptake (between 88.9 and 91.8%) was observed with aerobic fungal biomass from the exponential growth phase. Up to 1.0 mM cadmium gradually inhibited mycelium development, but never blocked it completely. Freeze-dried, oven-dried and non-metabolizing live Pleurotus sajor-caju biomass types were tested for their capacity to adsorb the test ion Cd²⁺ within the pH range of 4.5 to 6.0. Freeze–dried biomass proved to be the most efficient biomass type for Cd²⁺ metal adsorption. Therefore, Pleurotus sajor-caju may be used for heavy metal removal and bioremediation.