Glucose-containing polymer rings enable fed-batch operation in microtiter plates with parallel online measurement of scattered light,fluorescence, dissolved oxygen tension,and pH

Bioprocesses operated in batch mode can induce adverse effects like overflow metabolism, substrate inhibition, osmotic inhibition, oxygen limitation, and catabolite repression. To avoid these adverse effects, fed-batch is the predominant operation mode in industrial production. Nevertheless, screening for optimal production strains is usually performed in microtiter plates and shake flasks operated in batch mode without any online monitoring. Recently, a polymer-based controlled-release fed-batch microtiter plate with stable glucose release characteristics was described. In this study, a glucose-containing polymer matrix was used to manufacture polymer rings that were placed at the bottom of a 48-well microtiter plate. Thereby, the liquid content of the well became accessible for optical measurement by the BioLector device. Reflections caused by the polymer ring were minimized by adjusting the scattered-light measurement position. Influences on the measurement of the dissolved oxygen tension and pH could be avoided by choosing appropriate polymer-ring geometries. These adjustments enabled parallel online measurement of scattered light, fluorescence, dissolved oxygen tension, and pH of Escherichia coli BL21 (DE3) fed-batch cultivations. The online monitoring and fed-batch operation capabilities of the fed-batch microtiter plate presented in this study finds optimal application in screenings and initial process development.     

High-throughput screening of Hansenula polymorpha clones in the batch compared with the controlled-release fed-batch mode on a small scale

Most large-scale production processes in biotechnology are performed in fed-batch operational mode. In contrast, the screenings for microbial production strains are run in batch mode, which results in the microorganisms being subjected to different physiological conditions. This significantly affects strain selection. To demonstrate differences in ranking during strain selection depending on the operational mode, screenings were performed in batch and fed-batch modes. Two model populations of the methylotrophic yeast Hansenula polymorpha RB11 with vector pC10-FMD (P_FMD-GFP) (220 clones) and vector pC10-MOX (P_MOX-GFP) (224 clones) were applied. For fed-batch cultivations in deep-well microtiter plates, a controlled-release system made of silicone elastomer discs containing glucose was used. Three experimental set-ups were investigated: batch cultivation with (1) glucose as a substrate, which catabolite represses product formation, and (2) glycerol as a carbon source, which is partially repressing, respectively, and (3) fed-batch cultivation with glucose as a limiting substrate using the controlled-release system. These three experimental set-ups showed significant variations in green fluorescent protein (GFP) yield. Interestingly, screenings in fed-batch mode with glucose as a substrate resulted in the selection of yeast strains different from those cultivated in batch mode with glycerol or glucose. Ultimately, fed-batch screening is considerably better than screening in batch mode for fed-batch production processes with glucose as a carbon source.     

Establishing a Fed‐Batch Process for Protease Expression with Bacillus licheniformis in Polymer‐Based Controlled‐Release Microtiter Plates

Introducing fed‐batch mode in early stages of development projects is crucial for establishing comparable conditions to industrial fed‐batch fermentation processes. Therefore, cost efficient and easy to use small‐scale fed‐batch systems that can be integrated into existing laboratory equipment and workflows are required. Recently, a novel polymer‐based controlled‐release fed‐batch microtiter plate is described. In this work, the polymer‐based controlled‐release fed‐batch microtiter plate is used to investigate fed‐batch cultivations of a protease producing Bacillus licheniformis culture. Therefore, the oxygen transfer rate (OTR) is online‐monitored within each well of the polymer‐based controlled‐release fed‐batch microtiter plate using a µRAMOS device. Cultivations in five individual polymer‐based controlled‐release fed‐batch microtiter plates of two production lots show good reproducibility with a mean coefficient of variation of 9.2%. Decreasing initial biomass concentrations prolongs batch phase while simultaneously postponing the fed‐batch phase. The initial liquid filling volume affects the volumetric release rate, which is directly translated in different OTR levels of the fed‐batch phase. An increasing initial osmotic pressure within the mineral medium decreases both glucose release and protease yield. With the volumetric glucose release rate as scale‐up criterion, microtiter plate‐ and shake flask‐based fed‐batch cultivations are highly comparable. On basis of the small‐scale fed‐batch cultivations, a mechanistic model is established and validated. Model‐based simulations coincide well with the experimentally acquired data.     

Enhanced production of the nonribosomal peptide antibiotic valinomycin in Escherichia coli through small-scale high cell density fed-batch cultivation

Nonribosomal peptides (NRPs), a large family of natural products, possess numerous pharmaceutically significant bioactivities. However, many native microbial producers of NRPs are not cultivable or have low production yields making mass production infeasible. The recombinant production of natural products in a surrogate host has emerged as a strategy to overcome these limitations. De novo recombinant production of the NRP antibiotic valinomycin in an engineered Escherichia coli host strain was established with the necessary biosynthetic pathway constituents from Streptomyces tsusimaensis. In the present study, the initially modest valinomycin yields could be significantly increased from 0.3 up to 2.4 mg L^?1 by switching from a batch to an enzyme-based fed-batch mode in shake flasks. A subsequent design of experiment-driven optimization of parallel fed-batch cultivations in 24-well plates with online monitoring of dissolved oxygen and pH led to valinomycin yields up to 6.4 mg L^?1. Finally, repeated glucose polymer feeding to enzyme-based high cell density cultivations in shake flasks resulted in cell densities of OD₆₀₀ >50 and a valinomycin titer of appr. 10 mg L^?1. This represents a 33-fold improvement compared to the initial batch cultivations and is the highest concentration of a nonribosomal peptide which has been produced in E. coli without feeding of specific precursors so far to our knowledge. Also, such a small-scale optimization under fed-batch conditions may be generally applicable for the development and scale-up of natural product production processes in E. coli.     

Microbioreactor-assisted cultivation workflows for time-efficient phenotyping of protein producing Aspergillus niger in batch and fed-batch mode

In recent years, many fungal genomes have become publicly available. In combination with novel gene editing tools, this allows for accelerated strain construction, making filamentous fungi even more interesting for the production of valuable products. However, besides their extraordinary production and secretion capacities, fungi most often exhibit challenging morphologies, which need to be screened for the best operational window. Thereby, combining genetic diversity with various environmental parameters results in a large parameter space, creating a strong demand for time-efficient phenotyping technologies. Microbioreactor systems, which have been well established for bacterial organisms, enable an increased cultivation throughput via parallelization and miniaturization, as well as enhanced process insight via non-invasive online monitoring. Nevertheless, only few reports about microtiter plate cultivation for filamentous fungi in general and even less with online monitoring exist in literature. Moreover, screening under batch conditions in microscale, when a fed-batch process is performed in large-scale might even lead to the wrong identification of optimized parameters. Therefore, in this study a novel workflow for Aspergillus niger was developed, allowing for up to 48 parallel microbioreactor cultivations in batch as well as fed-batch mode. This workflow was validated against lab-scale bioreactor cultivations to proof scalability. With the optimized cultivation protocol, three different micro-scale fed-batch strategies were tested to identify the best protein production conditions for intracellular model product GFP. Subsequently, the best feeding strategy was again validated in a lab-scale bioreactor.     

On-line monitoring of recombinant bacterial cultures using multi-wavelength fluorescence spectroscopy

Multi-wavelength fluorescence spectroscopy was evaluated as a tool for on-line monitoring of recombinant Escherichia coli cultivations expressing human basic fibroblast growth factor (hFGF-2). The data sets for the various combinations of the excitation and emission spectra from batch cultivations were analyzed using principal component analysis. Chemometric models (the partial least squares method) were developed for correlating the fluorescence data and the experimentally measured variables such as the biomass and glucose concentrations as well as the carbon dioxide production rate. Excellent correlations were obtained for these variables for the calibration cultivations. The predictability of these models was further tested in batch and fed-batch cultivations. The batch cultivations were well predicted by the PLS models for biomass, glucose concentrations and carbon dioxide production rate (RMSEPs were respectively 5%, 7%, 9%). However, when tested for biomass concentrations in fed-batch cultivations (with final biomass three times higher than the highest calibration data) the models had good predictability at high growth rates (RMSEPs were 3% and 4%, respectively for uninduced and induced fed-batch cultivations), which was as good as for the batch cultivations used for developing the models (RMSEPs were 3% and 5%, respectively for uninduced and induced batch cultivations). The fed-batch cultivations performed at low growth rates exhibited much higher fluorescence for fluorophores such as flavin and NAD(P)H as compared to fed-batch cultivations at high growth rate. Therefore, the PLS models tended to over-predict the biomass concentrations at low growth rates. Obviously the cells changed their concentration of biogenic fluorophores depending on the growth rate. Although multi-wavelength fluorescence spectroscopy is a valuable tool for on-line monitoring of bioprocess, care must be taken to re-calibrate the PLS models at different growth rates to improve the accuracy of predictions.     

Equalizing growth in high‐throughput small scale cultivations via precultures operated in fed‐batch mode

An often underestimated problem when working with different clones in microtiter plates and shake flask screenings is the non‐parallel and non‐equal growth of batch cultures. These growth differences are caused by variances of individual clones regarding initial biomass concentration, lag‐phase or specific growth rate. Problems arising from unequal growth kinetics are different induction points in expression studies or uneven cultivation periods at the time of harvest. Screening for the best producing clones of a library under comparable conditions is thus often impractical or even impossible. A new approach to circumvent the problem of unequal growth kinetics of main cultures is the application of fed‐batch mode in precultures in microtiter plates and shake flasks. Fed‐batch operation in precultures is realized through a slow‐release system for glucose. After differently growing cultures turn to glucose‐limited growth, they all consume the same amount of glucose due to the fixed feed profile of glucose provided by the slow‐release system. This leads to equalized growth. Inherent advantages of this method are that it is easy to use and requires no additional equipment like pumps. This new technique for growth equalization in high‐throughput cultivations is simulated and verified experimentally. The growth of distinctly inoculated precultures in microtiter plates and shake flasks could be equalized for different microorganisms such as Escherichia coli and Hansenula polymorpha. Biotechnol. Bioeng. 2009;103: 1095–1102. © 2009 Wiley Periodicals, Inc.     

Production of a recombinant polyester-cleaving hydrolase from Thermobifida fusca in Escherichia coli

The hydrolase (Thermobifida fusca hydrolase; TfH) from T. fusca was produced in Escherichia coli as fusion protein using the OmpA leader sequence and a His₆ tag. Productivity could be raised more than 100-fold. Both batch and fed-batch cultivations yield comparable cell specific productivities whereas volumetric productivities differ largely. In the fed-batch cultivations final rTfH concentrations of 0.5 g L⁻¹ could be achieved. In batch cultivations the generated rTfH is translocated to the periplasm wherefrom it is completely released into the extracellular medium. In fed-batch runs most of the produced rTfH remains as soluble protein in the cytoplasm and only a fraction of about 35% is translocated to the periplasm. Migration of periplasmic proteins in the medium is obviously coupled with growth rate and this final transport step possibly plays an important role in product localization and efficacy of the Sec translocation process.     

In situ removal and purification of biosurfactants by automated surface enrichment

Erysipelothrix rhusiopathiae, the causative agent of swine erysipelas, was cultivated in a 5-L stirred and aerated bioreactor under different dissolved oxygen tensions (0%, 5%, and 30% of saturation) for evaluation of the influence of oxygen on cell growth as well as on the production of the main antigenic component of the vaccine against erysipelas, a 64–69 kDa protein (SpaA). The microorganism presented different growth profiles for different aeration conditions. However, at the end of the batch cultivations, similar cell concentrations were obtained under the studied conditions. In order to maximize biomass titers and antigen production, the microorganism was cultivated in fed-batch operation mode under aerobic conditions. Under this condition, there was a fivefold increase in biomass production in comparison to the results attained in batch cultivations. To follow up antigen expression, samples collected during batch cultivations were concentrated and treated with choline for antigen extraction. Antigen expression was then assessed by sodium dodecyl sulfate polyacrylamide gel electrophoresis and by murine immunization tests. It was observed a direct influence of oxygen availability upon antigen expression, which is favored in the presence of oxygen. Analysis of the samples collected throughout the fed-batch process also revealed that antigen production is growth associated.     

Comparison of polysialic acid production in Escherichia coli K1 during batch cultivation and fed-batch cultivation applying two different control strategies

The polysialic acid (PSA) production in Escherichia coli (E. coli) K1 was studied using three different cultivation strategies. A batch cultivation, a fed-batch cultivation at a constant specific growth rate of 0.25 h⁻¹ and a fed-batch cultivation at a constant glucose concentration of 50 mg l⁻¹ was performed. PSA formation kinetics under different cultivation strategies were analyzed based on the Monod growth model and the Luedeking-Piret equation. The results revealed that PSA formation in E. coli K1 was completely growth associated, the highest specific PSA formation rate (0.0489 g g⁻¹ h⁻¹) was obtained in the batch cultivation. However, comparing biomass and PSA yields on the glucose consumed, both fed-batch cultivations provided higher yields than that of the batch cultivation and acetate formation was prevented. Moreover, PSA yield on glucose was also correlated to the specific growth rate of the cells. The optimal specific growth rate for PSA production was 0.32 h⁻¹ obtained in the fed-batch cultivation at a constant glucose concentration of 50 mg l⁻¹, with highest conversion efficiency of 43 mg g⁻¹.     

Intracellular pH-based controlled cultivation of yeast cells: II. cultivation methodology

Intracellular pH (pH(i)) was measured on-line in a bioreactor using a fluorescent pH(i) indicator, 9-aminoacridine, and controlled fed-batch cultivations of yeast cells based on pH(i) (FB-pH(i)) were performed. In FB-pH(i) cultivations, automated glucose additions were made to the culture in response to culture pH(i). The average ethanol (an-aerobic product) yield was significantly lower [0.12 g g(-1) glucose in fed-batch pH(i) cultivations with 100 ppm glucose additions (FB-pH(i)-100 cultivation) vs. 0.48 g g(-1) glucose in batch] and cell yield was higher (0.54 g g(-1) glucose in FB-pH(i)-100 cultivation vs. 0.3 g g(-1) glucose in batch) compared to batch cultivation. An expression has been derived to calculate changes in pH(i) from measured fluorescence values when the cell concentration increases during growth. Cultivations based on pH(i), performed with different magnitudes of glucose addition (100, 50, and 10 ppm additions), showed that lower magnitudes of glucose addition resulted in lower ethanol yields while cell yield remained unaffected. The ratio of specific oxygen uptake rate to specific glucose uptake rate (OUR/GUR) increased with decreased in magnitude of glucose additions in FB-pH(i) cultivations, suggesting that the culture aerobic state was higher when the magnitude of glucose addition was lower. The average cell productivity in FB-pH(i) cultivations was 29% higher than in batch cultivation. Cells were also cultivated at high OUR conditions, and the results are compared with other cultivations. (c) 1993 John Wiley & Sons, Inc.     

Process performance of parallel bioreactors for batch cultivation of Streptomyces tendae

Batch cultivations of the nikkomycin Z producer Streptomyces tendae were performed in three different parallel bioreactor systems (milliliter-scale stirred-tank reactors, shake flasks and shaken microtiter plate) in comparison to a standard liter-scale stirred-tank reactor as reference. Similar dry cell weight concentrations were measured as function of process time in stirred-tank reactors and shake flasks, whereas only poor growth was observed in the shaken microtiter plate. In contrast, the nikkomycin Z production differed significantly between the stirred and shaken bioreactors. The measured product concentrations and product formation kinetics were almost the same in the stirred-tank bioreactors of different scale. Much less nikkomycin Z was formed in the shake flasks and MTP cultivations, most probably due to oxygen limitations. To investigate the non-Newtonian shear-thinning behavior of the culture broth in small-scale bioreactors, a new and simple method was applied to estimate the rheological behavior. The apparent viscosities were found to be very similar in the stirred-tank bioreactors, whereas the apparent viscosity was up to two times increased in the shake flask cultivations due to a lower average shear rate of this reactor system. These data illustrate that different engineering characteristics of parallel bioreactors applied for process development can have major implications for scale-up of bioprocesses with non-Newtonian viscous culture broths.     

FeedER: a feedback-regulated enzyme-based slow-release system for fed-batch cultivation in microtiter plates

With the advent of modern genetic engineering methods, microcultivation systems have become increasingly important tools for accelerated strain phenotyping and bioprocess engineering. While these systems offer sophisticated capabilities to screen batch processes, they lack the ability to realize fed-batch processes, which are used more frequently in industrial bioprocessing. In this study, a novel approach to realize a feedback-regulated enzyme-based slow-release system (FeedER), allowing exponential fed-batch for microscale cultivations, was realized by extending our existing Mini Pilot Plant technology with a customized process control system. By continuously comparing the experimental growth rates with predefined set points, the automated dosage of Amyloglucosidase enzyme for the cleavage of dextrin polymers into d-glucose monomers is triggered. As a prerequisite for stable fed-batch operation, a constant pH is maintained by automated addition of ammonium hydroxide. We show the successful application of FeedER to study fed-batch growth of different industrial model organisms including Corynebacterium glutamicum, Pichia pastoris, and Escherichia coli. Moreover, the comparative analysis of a C. glutamicum GFP producer strain, cultivated under microscale batch and fed-batch conditions, revealed two times higher product yields under slow growing fed-batch operation. In summary, FeedER enables to run 48 parallel fed-batch experiments in an automated and miniaturized manner, and thereby accelerates industrial bioprocess development at the screening stage.

     

Calorimetric control of fed-batch cultures of Saccharomyces cerevisiae

Calorimetry has been used to control the glucose feeding in fed-batch cultures of S. cerevisiae in order to avoid ethanol formation and maintain a fully respiratory metabolism. Comparisons between batch and fed-batch cultivations showed that the former had a much lower growth yield. The growth yields for fed-batch cultivations were more than 30% higher than for batch cultures. However, energy balance calculations showed that a large part of the increase could be explained by the evaporation of ethanol during batch cultivations. When the growth yields obtained from the batch cultures were corrected for the evaporation of ethanol, the increase in growth yield for fed-batch cultures was about 10%.     

Cultivation of microalgae for oil production with a cultivation strategy of urea limitation

The microalgae, Chlorella sp., were cultivated in various culture modes to assess biomass and lipid productivity in this study. In the batch mode, the biomass concentrations and lipid content of Chlorella sp. cultivated in a medium containing 0.025–0.200 g L⁻¹ urea were 0.464–2.027 g L⁻¹ and 0.661–0.326 g g⁻¹, respectively. The maximum lipid productivity of 0.124 g d⁻¹ L⁻¹ occurred in a medium containing 0.100 g L⁻¹ urea. In the fed-batch cultivation, the highest lipid content was obtained by feeding 0.025 g L⁻¹ of urea during the stationary phase, but the lipid productivity was not significantly increased. However, a semi-continuous process was carried out by harvesting the culture and renewing urea at 0.025 g L⁻¹ each time when the cultivation achieved the early stationary phase. The maximum lipid productivity of 0.139 g d⁻¹ L⁻¹ in the semi-continuous culture was highest in comparison with those in the batch and fed-batch cultivations.     

Modeling of lutein production by heterotrophic <Emphasis Type="Italic">Chlorella</Emphasis> in batch and fed-batch cultures

Chlorella is a promising alternative resource of lutein (xanthophyll) production as it can be cultivated heterotrophically in fermentors. In this paper, a kinetic model for lutein production by heterotrophic Chlorella pyrenoidosa was developed based on batch cultivations in 250-ml flasks and a 19-l fermentor. The model was validated by experimental data from two fed-batch cultivations performed in the same fermentor. The dynamic behavior of lutein production by C. pyrenoidosa with various concentrations of glucose and nitrogen was analyzed based on the kinetic model. Model-based analyses suggested that glucose concentrations between 5 and 24 g/l and nitrogen concentrations between 0.7 and 12 g/l during the cultivation were favorable for lutein production by heterotrophic C. pyrenoidosa. It also showed that fed-batch cultivations are more suitable for efficient production of lutein than batch ones. The results obtained in this study may contribute to commercial lutein production by heterotrophic Chlorella.     

Engineered <Emphasis Type="Italic">E. coli</Emphasis> W enables efficient 2,3-butanediol production from glucose and sugar beet molasses using defined minimal medium as economic basis

Background

Efficient microbial production of chemicals is often hindered by the cytotoxicity of the products or by the pathogenicity of the host strains. Hence 2,3-butanediol, an important drop-in chemical, is an interesting alternative target molecule for microbial synthesis since it is non-cytotoxic. Metabolic engineering of non-pathogenic and industrially relevant microorganisms, such as Escherichia coli, have already yielded in promising 2,3-butanediol titers showing the potential of microbial synthesis of 2,3-butanediol. However, current microbial 2,3-butanediol production processes often rely on yeast extract as expensive additive, rendering these processes infeasible for industrial production.

Results

The aim of this study was to develop an efficient 2,3-butanediol production process with E. coli operating on the premise of using cost-effective medium without complex supplements, considering second generation feedstocks. Different gene donors and promoter fine-tuning allowed for construction of a potent E. coli strain for the production of 2,3-butanediol as important drop-in chemical. Pulsed fed-batch cultivations of E. coli W using microaerobic conditions showed high diol productivity of 4.5 g l^?1 h^?1. Optimizing oxygen supply and elimination of acetoin and by-product formation improved the 2,3-butanediol titer to 68 g l^?1, 76% of the theoretical maximum yield, however, at the expense of productivity. Sugar beet molasses was tested as a potential substrate for industrial production of chemicals. Pulsed fed-batch cultivations produced 56 g l^?1 2,3-butanediol, underlining the great potential of E. coli W as production organism for high value-added chemicals.

Conclusion

A potent 2,3-butanediol producing E. coli strain was generated by considering promoter fine-tuning to balance cell fitness and production capacity. For the first time, 2,3-butanediol production was achieved with promising titer, rate and yield and no acetoin formation from glucose in pulsed fed-batch cultivations using chemically defined medium without complex hydrolysates. Furthermore, versatility of E. coli W as production host was demonstrated by efficiently converting sucrose from sugar beet molasses into 2,3-butanediol.

     

Production of recombinant Chikungunya virus envelope 2 protein in Escherichia coli

Chikungunya, a mosquito-borne viral disease caused by Chikungunya virus (CHIKV), has drawn substantial attention after its reemergence causing massive outbreaks in tropical regions of Asia and Africa. The recombinant envelope 2 (rE2) protein of CHIKV is a potential diagnostic as well as vaccine candidate. Development of cost-effective cultivation media and appropriate culture conditions are generally favorable for large-scale production of recombinant proteins in Escherichia coli. The effects of medium composition and cultivation conditions on the production of recombinant Chikungunya virus E2 (rCHIKV E2) protein were investigated in shake flask culture as well as batch cultivation of Escherichia coli. Further, the fed-batch process was also carried out for high cell density cultivation of E. coli expressing rE2 protein. Expression of rCHIKV E2 protein in E. coli was induced with 1 mM isopropyl-beta-thiogalactoside (IPTG) at ~23 g dry cell weight (DCW) per liter of culture and yielded an insoluble protein aggregating to form inclusion bodies. The final DCW after fed-batch cultivation was ~35 g/l. The inclusion bodies were isolated, solubilized in 8 M urea and purified through affinity chromatography to give a final product yield of ~190 mg/l. The reactivity of purified E2 protein was confirmed by Western blotting and enzyme-linked immunosorbent assay. These results show that rE2 protein of CHIKV may be used as a diagnostic reagent or for further prophylactic studies. This approach of producing rE2 protein in E. coli with high yield may also offer a promising method for production of other viral recombinant proteins.     

IS2-mediated overexpression of kfoC in E. coli K4 increases chondroitin-like capsular polysaccharide production

Transposons are developing molecular tools commonly used for several applications: one of these is the delivery of genes into microorganisms. These mobile genetic elements are characterised by two repeated insertion sequences that flank a sequence encoding one or more orfs for a specific transposase that moves these sequences to other DNA sites. In the present paper, the IS2 transposon of Escherichia coli K4 was modified in vitro by replacing the sequence coding for the transposase with that of the kfoC gene that codes for chondroitin polymerase. KfoC is responsible for the polymerisation of the bacterial capsular polysaccharide whose structure is analogous to that of chondroitin sulphate, a glycosaminoglycan with established and emerging biomedical applications. The recombinant construct was stably integrated into the genome of E. coli K4 by exploiting the transposase from endogenous copies of IS2 in the E. coli chromosome. A significant improvement of the polysaccharide production was observed, resulting in 80 % higher titres in 2.5-L fed-batch cultivations and up to 3.5 g/L in 22-L fed-batch cultures.     

Replication methods and tools in high-throughput cultivation processes - recognizing potential variations of growth and product formation by on-line monitoring

Background  

High-throughput cultivations in microtiter plates are the method of choice to express proteins from recombinant clone libraries. Such processes typically include several steps, whereby some of them are linked by replication steps: transformation, plating, colony picking, preculture, main culture and induction. In this study, the effects of conventional replication methods and replication tools (8-channel pipette, 96-pin replicators: steel replicator with fixed or spring-loaded pins, plastic replicator with fixed pins) on growth kinetics of Escherichia coli SCS1 pQE-30 pSE111 were observed. Growth was monitored with the BioLector, an on-line monitoring technique for microtiter plates. Furthermore, the influence of these effects on product formation of Escherichia coli pRhotHi-2-EcFbFP was investigated. Finally, a high-throughput cultivation process was simulated with Corynebacterium glutamicum pEKEx2-phoD-GFP, beginning at the colony picking step.