An ethyl acetate sensor utilizing cataluminescence on Y2O3 nanoparticles

A cataluminescence (CTL) sensor using Y₂O₃ nanoparticles as the sensing materials was proposed for the determination of ethyl acetate. This ethyl acetate sensor showed high sensitivity and specificity at the optimal temperature of 264°C. Quantitative analysis was performed at a wavelength of 425 nm. The linear ranges of CTL intensity vs ethyl acetate concentrations were 2.0–250 ppm (r = 0.9965) and 250–6500 ppm (r = 0.9997) with a detection limit (3σ) of 0.5 ppm. There was no response or weak response when foreign substances such as formic acid, n‐hexane, toluene, acetic acid, benzene, and formaldehyde passing through the surface of Y₂O₃ nanoparticles. The sensor had a long lifetime more than 80 h with 3600 ppm ethyl acetate. It had been applied successfully to determine ethyl acetate in artificial air samples. Copyright © 2009 John Wiley & Sons, Ltd.     

Development of a cataluminescence sensor for detecting benzene based on magnesium silicate hollow spheres

A novel and sensitive gas sensor was developed for the determination of benzene based on its cataluminescence (CTL) by oxidation in air on the surface of hollow magnesium silicate spheres. Luminescence characteristics and optimum conditions were investigated. Results indicated that the as‐prepared magnesium silicate hollow spheres exhibited outstanding CTL properties such as stable intensity, high signal/noise values, and short response and recovery times. Under optimized conditions, benzene exhibited a broad linear range of 1–4500 ppm, with a correlation coefficient of 0.9946 and a limit of detection (signal‐to‐noise ratio (S/N) = 3) of 0.6 ppm, which was below the standard permitted concentration. The relative standard deviation (RSD) for 100 ppm benzene was 4.3% (n = 6). Furthermore, the gas sensor system showed outstanding selectivity for benzene compared with nine other common volatile organic compounds (VOCs). The proposed gas sensor showed good characteristics of high selectivity, fast response time and long lifetime, which suggested the promising application of magnesium silicate hollow spheres as a novel highly efficient CTL sensing material. The mechanism for the improved performance was also discussed based on the experimental results. Copyright © 2014 John Wiley & Sons, Ltd.     

Detection of hydrogen sulphide using cataluminescence sensors based on alkaline-earth metal salts

Detection of hydrogen sulphide (H₂S) was conducted based on cataluminescence (CTL) sensors, using alkaline‐earth metal carbonates as catalysts. Optimal working conditions, analytical characteristics and the response properties of the sensor were investigated. CTL intensity examination showed that sensors fabricated with CaCO₃, SrCO₃ or BaCO₃ could be used to detect H₂S gas sensitively. The optimal sensing temperature was about 320 °C. Under the sensing conditions with temperature at ca. 320 °C and gas flow rate in the range 180–200 mL/min, the linear range of CTL intensity vs H₂S concentration was 25–500 ppm, with a detection limit of 2 ppm. The response and recovery times of the sensor were within 5 and 25 min, respectively. Also, the sensor had the property of high selectivity to H₂S with very weak or no obvious response to 14 other gases, such as NO₂, NH₃, hydrocarbons and alcohol. Copyright © 2011 John Wiley & Sons, Ltd.     

Sensitive and selective system of benzene detection based on a cataluminescence sensor

Au/La₂O₃ nanomaterials were prepared through calcining Au‐modified La(OH)₃ precursors. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X‐ray diffractometry (XRD) were employed to characterize the as‐prepared samples. Benzene, a common volatile organic compound, was selected as a model to investigate the cataluminescence (CTL)‐sensing properties of the Au/La₂O₃ nanomaterials. Results indicated that the as‐prepared Au/La₂O₃ exhibited outstanding CTL properties such as stable intensity, high signal‐to‐noise values, and short response and recovery times. Under optimized conditions, the benzene assay exhibited a broad linear range of 1–4000 ppm, with a limit of detection of 0.7 ppm, which was below the standard permitted concentrations. Furthermore, the gas sensor system showed outstanding selectivity for benzene compared with seven other types of common volatile organic compounds (VOCs). The proposed gas sensor showed good characteristics with high selectivity, fast response time and long lifetime, which suggested the promising application of the Au/La₂O₃ nanomaterials as a novel highly efficient CTL‐sensing material. Copyright © 2013 John Wiley & Sons, Ltd.     

Development of highly sensitive sensor system for methane utilizing cataluminescence

A gaseous sensor system was developed for the detection of methane based on its cataluminescence emission. Cataluminescence characteristics and optimal conditions were studied in detail under optimized experimental conditions. Results showed that the methane cataluminescence sensor system could cover a linear detection range from 10 to 5800 ppm (R = 0.9963, n = 7) and the detection limit was about 7 ppm (S/N = 3), which was below the standard permitted concentration. Moreover, a linear discriminant analysis method was used to test the recognizable performance of the methane sensor. It was found that methane, ethane, propane and pentane could be distinguished clearly. Its methane sensing properties, including improved sensitivity, selectivity, stability and recognition demonstrated the TiO₂/SnO₂ materials to be promising candidates for constructing a cataluminescence‐based gas sensor that could be used for detecting explosive gas contaminants. Copyright © 2015 John Wiley & Sons, Ltd.     

A cataluminescence gas sensor for ammonium sulfide based on Fe3O4–carbon nanotubes composite

In the present work, Fe₃O₄–carbon nanotubes (CNTs) composite was explored as a sensing material candidate for ammonium sulfide. Intense chemiluminescence emission can be observed during the catalytic oxidation of ammonium sulfide on the surface of Fe₃O₄–CNTs composite. Based on this phenomenon, a selective and sensitive gas sensor for the determination of ammonium sulfide was demonstrated. Under the optimized conditions, the linear range of cataluminescence intensity vs concentration of ammonium sulfide gas was 1.4–115 µg mL^?1 (R = 0.998) with a limit of detection (S/N = 3) of 0.05 µg mL^?1. The relative standard deviation (n = 5) for 14.3 µg mL^?1 ammonium sulfide was 1.9%. There was no response to common foreign substances, such as sulfur dioxide, toluene, aether, ethanol, acetone, hydrogen sulfide, carbon bisulfide, benzene and ammonia. The proposed sensor was successfully applied for the determination of ammonium sulfide in artificial air samples. Copyright © 2009 John Wiley & Sons, Ltd.     

Fluoride‐sensitivity of growth and acid production of oral Actinomyces: comparison with oral Streptococcus

Actinomyces are predominant oral bacteria; however, their cariogenic potential in terms of acid production and fluoride sensitivity has not been elucidated in detail and compared with that of other caries‐associated oral bacteria, such as Streptococcus. Therefore, this study aimed to elucidate and compare the acid production and growth of Actinomyces and Streptococcus in the presence of bicarbonate and fluoride to mimic conditions in the oral cavity. Acid production from glucose was measured by pH‐stat at pH 5.5 and 7.0 under anaerobic conditions. Growth rate was assessed by optical density in anaerobic culture. Although Actinomyces produced acid at a lower rate than did Streptococcus, their acid production was more tolerant of fluoride (ID_{acid production} 50 = 110–170 ppm at pH 7.0 and 10–13 ppm at pH 5.5) than that of Streptococcus (ID_{acid production} 50 = 36–53 ppm at pH 7.0 and 6.3–6.5 ppm at pH 5.5). Bicarbonate increased acid production by Actinomyces with prominent succinate production and enhanced their fluoride tolerance (ID_{acid production} 50 = 220–320 ppm at pH 7.0 and 33–52 ppm at pH 5.5). Bicarbonate had no effect on these variables in Streptococcus. In addition, although the growth rate of Actinomyces was lower than that of Streptococcus, Actinomyces growth was more tolerant of fluoride (ID_growth 50 = 130–160 ppm) than was that of Streptococcus (ID_growth 50 = 27–36 ppm). These results indicate that oral Actinomyces are more tolerant of fluoride than oral Streptococcus, and bicarbonate enhances the fluoride tolerance of oral Actinomyces. Because of the limited number of species tested here, further study is needed to generalize these findings to the genus level.     

Analysis of 2‐propanol in exhaled breath using in situ enrichment and cataluminescence detection

We report a simple gaseous sensor for the sensitive detection of trace 2‐propanol in exhaled breath using in situ enrichment and cataluminescence detection method on the surface of nanomaterials. The influences of heating voltage and absorption time on the CTL intensity were discussed, respectively. In the selected conditions, the linear range of 2‐propanol concentration is 60–600 ppbv and the detection of limit is 11 ppbv. Moreover, the lifetime and selectivity of the sensor were also investigated. It has the potential to diagnostic volatile organic compounds in human breath. Copyright © 2010 John Wiley & Sons, Ltd     

Nanosized gamma-Al2O3 + Nd2O3-based cataluminescence sensor for ethylene dichloride.

A gas-sensor utilizing cataluminescence (CTL) on nanosized gamma-Al2O3 + Nd2O3 for measuring low concentrations of gaseous ethylene dichloride (EDC) was developed. The results showed that gamma-Al2O3 nanoparticles as a catalyst offered high sensitivity and selectivity in the detection of EDC. The addition of a small quantity of Nd2O3 increased the intensity of CTL more than two-fold. Quantitative analysis was performed at a wavelength of 400 nm and at an optimal temperature of 279 degrees C, and the optimal flow rate of carrier gas was 320 mL/min. Under the optimized conditions, the linear range of CTL intensity vs. concentration is 6-5000 ppm (R = 0.9996; n = 7), with a detection limit of 2 ppm. The response time is <5 s. No interference or only very low levels of significant interference were observed when substances such as formaldehyde, n-hexane, methyl benzene, carbon tetrachloride, chloroform and benzene were passed through the sensor.     

Development of a benzaldehyde sensor utilizing chemiluminescence on nanosized Y2O3

A chemiluminescence sensor has been proposed for sensitive determination of benzaldehyde, with nanosized Y₂O₃ as the sensing material. Under optimized conditions, the linear range of the CL intensity vs. the concentration of benzaldehyde vapour is 1.8 ng/mL–10.8 µg/mL (r² = 0.9996), with a detection limit of 0.90 ng/mL (signal:noise ratio = 3:1). The sensor also exhibits high selectivity to benzaldehyde because no or weak CL signals have been detected when foreign substances are introduced into the sensor. In addition, the sensor also shows good stability and longer lifetime within 100 h. The results indicate that the proposed sensor, which has high sensitivity and selectivity, shows great potential for the detection of benzaldehyde. Copyright © 2008 John Wiley & Sons, Ltd.     

Elevated carbon dioxide affects leaf-miner performance and plant growth in docks (Rumex spp.)

Exposure of R. crispus and R. obtusifolius to elevated CO₂ (600 ppm) resulted in an increased C:N ratio of leaf tissue and greater leaf areas. Larvae of P. nigritarsis mining leaves of R. obtusifolius during exposure produced significantly bigger mines in elevated than in ambient (350 ppm) conditions. There were no significant treatment effects on pupal weight although in both host species mean weight was greater in ambient than in elevated conditions. These results are consistent with the hypothesis that insect herbivores compensate for increased C:N ratios by increased food consumption. This response by herbivores may partially offset predicted increases in plant biomass in a future high CO₂ environment.     

A novel gaseous dimethylamine sensor utilizing cataluminescence on zirconia nanoparticles

A novel cataluminescence (CTL) sensor using ZrO₂ nanoparticles as the sensing material was developed for the determination of trace dimethylamine in air samples based on the catalytic chemiluminescence (CL) of dimethylamine on the surface of ZrO₂ nanoparticles. The CTL characteristics and the different factors on the signal intensity for the sensor, including nanomaterials, working temperature, wavelength and airflow rate, were investigated in detail. The CL intensity on ZrO₂ nanoparticles was the strongest among the seven examined catalysts. This novel CL sensor showed high sensitivity and selectivity to gaseous dimethylamine at optimal temperature of 330°C. Quantitative analysis was performed at a wavelength of 620 nm. The linear range of CTL intensity vs concentration of gaseous dimethylamine was 4.71 × 10^?3 to 7.07 × 10^?2 mg L^?1 (r = 0.9928) with a detection limit (3σ) of 6.47 × 10^?4 mg L^?1. No or only very low levels of interference were observed while the foreign substances such as benzene, hydrochloric acid, methylbenzene, chloroform, n‐hexane and water vapor were passing through the sensor. The response time of the sensor was less than 50 s, and the sensor had a long lifetime of more than 60 h. The sensor was successfully applied to the determination of dimethylamine in artificial air samples, and could potentially be applied to analysis of nerve agents such as Tabun (GA). Copyright © 2009 John Wiley & Sons, Ltd.     

Detection of volatile organic compounds released by wood furniture based on a cataluminescence test system

Wood furniture is an important source of indoor air pollution. To date, the detection of harmful substances in wood furniture has relied on the control of a single formaldehyde component, therefore the detection and evaluation of pollutants released by wood furniture are necessary. A novel method based on a cataluminescence (CTL) sensor system generated on the surface of nano‐3TiO₂–2BiVO₄ was proposed for the simultaneous detection of pollutants released by wood furniture. Formaldehyde and benzene were selected as a model to investigate the CTL‐sensing properties of the sensor system. Field emission scanning electronic microscopy (FESEM), transmission electron microscopy (TEM) and X‐ray diffraction (XRD) were employed to characterize the as‐prepared samples. The results showed that the as‐prepared test system exhibited outstanding CTL properties such as stable intensity, a high signal‐to‐noise ratio, and short response and recovery times. In addition, the limit of detection for formaldehyde and benzene was below the standard permitted concentrations. Moreover, the sensor system showed outstanding selectivity for formaldehyde and benzene compared with eight other common volatile organic compounds (VOCs). The performance of the sensor system will enable furniture VOC limit emissions standards to be promulgated as soon as possible. Copyright © 2015 John Wiley & Sons, Ltd.     

Highly sensitive electrochemiluminescence determination of etamsylate using a low‐cost electrochemical flow‐through cell based on a tris(2, 2'‐bipyridyl)ruthenium(II)–Nafion‐modified carbon paste electrode

A simple and sensitive electrochemiluminescence (ECL) method for the determination of etamsylate has been developed by coupling an electrochemical flow‐through cell with a tris(2,2'‐bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺)–Nafion‐modified carbon electrode. It is based on the oxidized Ru(bpy)₃²⁺ on the electrode surface reacting with etamsylate and producing an excellent ECL signal. Under optimized experimental conditions, the proposed method allows the measurement of etamsylate over the range of 8–1000 ng/mL with a correlation coefficient of r = 0.9997 (n = 7) and a limit of detection of 1.57 ng/mL (3σ), the relative standard deviation (RSD) for 1000 ng/mL etamsylate (n = 7) is 0.96%. The immobilized Ru(bpy)₃²⁺ carbon paste electrode shows good electrochemical and photochemical stability. This method is rapid, simple, sensitive and has good reproducibility. It has been successfully applied to the determination of the studied etamsylate in pharmaceutical preparations with satisfactory results. The possible ECL reaction mechanism has also been discussed. Copyright © 2013 John Wiley & Sons, Ltd.     

Research on benzene,toluene and dimethylbenzene detection based on a cataluminescence sensor

We present a sensitive and quick way to determine benzene, toluene and dimethylbenzene (BTEX) in air, applying a cataluminescence (CTL) sensor based on a nano‐sized composite material, γ‐Al₂O₃/PtO₂. The factors that affect the sensor's performance were studied, including the sensing material, temperature, rate of air carrier and wavelength. It was shown that when Pt accounted for 0.2% of the sensing material, the rate of the air carrier that carries target gas was 450 mL/min, the determination wavelength was 400 nm and temperature was 236°C, this sensor showed the best CTL intensity to BTEX. In addition, the CTL intensity had a high linear relation with the concentration of BTEX, with a linear range from 0.5 to 100 mL/m³, and a detection limit 0.22 mL/m³. This nano‐sized material had a quick response within 1.5 s, short recovery time within 1 min and a long lifetime, showing good potential for a variety of applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Determination of clomipramine by flow‐injection analysis with acidic potassium permanganate–formic acid chemiluminescence detection

A sensitive and simple chemiluminescent (CL) method for the determination of clomipramine has been developed by combining the flow‐injection analysis (FIA) technique, which is based on the CL intensity generated from the redox reaction of potassium permanganate (KMnO₄)–formic acid in sulphuric acid (H₂SO₄) medium. Under the optimum conditions, the linear range for the determination of clomipramine was 0.04–4 µg/mL, with a correlation coefficient of 0.9988 (n = 10) and a detection limit of 0.008 µg/mL (3σ), and the relative standard deviation (RSD) for 2.0 µg/mL clomipramine (n = 11) is 1.26%. The proposed method has been successfully applied to the determination of the studied clomipramine in pharmaceutical preparations. The possible reaction mechanism is discussed. Copyright © 2011 John Wiley & Sons, Ltd.     

Biotoxic effects of Sumisclex and Carbomar fungicides on four Aspergillus species isolated from the rhizosphere of some Taif plants

Abstract

The antifungal activities of two systemic fungicides (Sumisclex and Carbomar) on four rhizospheric Aspergillus species (A. candidus, A. sydawi, A. niger1 and A. niger2) were studied. Also the phytotoxicity against some saudian seeds was analysed. Results indicated that Sumisclex fungicide was more effective on the growth of A. candidus and A. sydawi under laboratory conditions (the IC₅₀ of 3 and 4 ppm were recorded, respectively) than Carbomar where an IC₅₀ of 11 ppm for A. candidus and 35 ppm for A. sydawi were observed. The growth of the two strains of A. niger was completely inhibited by Carbomar even at the lowest 10 ppm concentration. On the other hand results revealed that phytotoxicity was apparently linked with the type of the fungicide and its concentration. However, the root system was more sensitive to the tested fungicides especially at higher concentrations.     

Dual-wavelength plasmonic perfect absorber suitable for refractive index sensing

In this paper, a plasmonic perfect absorber (PPA) based on metal-insulator-metal-insulator-metal (MIMIM) structure has been designed for refractive index sensing of glucose solutions (analyte) and then a new method has been proposed for fast, low-cost, and easy measurement of sensor’s sensitivity. Simulation results show that the absorption spectrum of the proposed sensor has two resonance peaks that with an increase in analyte refractive index, both of them are red-shifted. In our proposed measurement technique, two conventional single-wavelength lasers (with wavelengths of 1050 nm and 1750 nm) are used for vertical plane wave light illumination on the structure. Then, the absorbed powers at 1750 nm (A₂) and 1050 nm (A₁) wavelengths are calculated and variation of the absorption ratio (A₂/A₁) due to change of analyte refractive index would be introduced as the sensitivity of sensor (S = Δ(A₂/A₁)/Δn). Obtained results show that the increase of analyte refractive index from n = 1.312 to n = 1.384 will result in an increase of sensor’s sensitivity from 9.3/RIU to 33.475/RIU.

     

Online naphazoline quality control by micellar‐enhanced spectrofluorimetry

The aim of this study was to develop a method for online spectrofluorimetric quality control of naphazoline (NPZ) in pharmaceuticals and raw drugs. A combination of a flow‐injection analysis (FIA) system with micellar‐enhanced fluorescence detection is presented as a powerful alternative for the rapid and sensitive analysis of naphazoline. Since NPZ shows low native fluorescence, the use of an anionic surfactant, such as sodium dodecyl sulphate (SDS), provides a considerable enhancement of fluorescence intensity and the nature of the technique allows a possible and easy adaptation to a FIA system. Using λ_exc = 280 nm and λ_em = 326 nm, a good linear relationship (LOL) was obtained in the range 0.003–10 µg mL^?1 with a detection limit (LOD) of 3 × 10^?4 µg mL^?1 (s/n = 3). Parameters related to the nature of the analytical signal and to the FIA manifold were optimized. Satisfactory recoveries were obtained in the analysis of commercial pharmaceutical formulations. The proposed method is simple, accurate and allows for high‐speed sampling and considerably shorter analysis times. In addition, it requires inexpensive equipment and reagents and has easy operational conditions and no side effects, thus avoiding environmental pollution through toxic waste. Copyright © 2011 John Wiley & Sons, Ltd.     

Flowcell culture of Porphyromonas gingivalis biofilms under anaerobic conditions

We have developed an anaerobic biofilm culture system. The system is inexpensive, simple to use and, unlike an anaerobic glovebox, requires no dedicated space. As a test of the system, Porphyromonas gingivalis was cultured under low oxygen (1–2 ppm) and under anaerobic conditions (≤0.1 ppm O₂). In the presence of small amounts of oxygen, the organism attached and formed an initial biofilm over the course of 4 h, but the biofilm was unable to maintain its growth and had lost biomass after 18 h. Also, ambiguous results were obtained when the biofilm was stained with a viability stain. Under anaerobic conditions, the biofilm was able to continue growth — biomass was greater after 18 h than after 4 h, and the anaerobic biofilm had a less ambiguous staining pattern than did the low-O₂-grown biofilm.