Agar-based magnetic affinity support for protein adsorption

Magnetic colloidal particles were prepared by a coprecipitation method. The particles were composed of nanometer-sized superparamagnetic Fe(3)O(4) particles stabilized by lauric acid. Then, magnetic agar gel beads were produced by a water-in-oil emulsification method using a mixture of agar solution and the magnetic colloidal particles as the aqueous phase. A reactive triazine dye, Cibacron blue 3GA (CB), was coupled to the gel to prepare an agar-based magnetic affinity support (MAS) for protein adsorption. The support showed good magnetic responsiveness in a magnetic field. Bovine serum albumin (BSA) was used as a model protein to test adsorption equilibrium and kinetic behavior of the MAS. The adsorption equilibrium of BSA to the MAS was described by the Langmuir-type isotherm. Adsorption capacity of the MAS for BSA was up to 25 mg/mL at a CB coupling density of 1.6 micromol/mL. The effect of ionic strength on BSA adsorption was complex, exhibiting a maximum capacity at an ionic strength of 0.06 mol/L. The adsorption of BSA to the MAS was also influenced by pH. Uptake rate of BSA to the MAS was analyzed using a pore diffusion model. The pore diffusion coefficient was estimated to be 1.75 x 10(-11) m(2)/s. Finally, recycled use of the MAS demonstrated the stability of the MAS in protein adsorption and magnetic responsiveness.     

Film formation from colloidal dispersions stabilized by sugar derivatives and their controllable release for selective protein adsorption

Although the use of sugar and sugar derivatives has been documented in polymer research for many years, there are no reports that would utilize these species as polymerization sites of colloidal polymeric particles that, later on, may be released during particle coalescence to form films with surfaces that differentiate protein adsorption. These studies show that, when n-dodecyl-beta-D-maltoside (DDM) is utilized for the synthesis and stabilization of poly[methyl methacrylate-co-(n-butyl acrylate)] (p-MMA/nBA) colloidal particles, upon particle coalescence DDM stratifies near the film-air (F-A) interface. By using attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy and internal reflection infrared imaging (IRIRI), comparative adsorption studies on p-MMA/nBA surfaces exposed to globulin (Glo), fibrinogen (Fib), and bovine serum albumin (BSA) reveal that the presence of DDM selectively inhibits Glo and Fib adsorption, but does not affect BSA. The presence of DDM also enhances the rate of mobility of sodium dioctylsulfosuccinate (SDOSS) resulting from interactions between DDM and SDOSS moieties, and the surface morphologies change as a result of concentration variations of DDM in the colloidal dispersions.     

Competitive protein adsorption on polysaccharide and hyaluronate modified surfaces

Adsorption of bovine serum albumin (BSA) and fibrinogen (Fg) was measured on six distinct bare and dextran- and hyaluronate-modified silicon surfaces created using two dextran grafting densities and three hyaluronic acid (HA) sodium salts derived from human umbilical cord, rooster comb and Streptococcus zooepidemicus. Film thickness and surface morphology depended on the HA molecular weight and concentration. BSA coverage was enhanced on surfaces in competitive adsorption of BSA:Fg mixtures. Dextranization differentially reduced protein adsorption onto surfaces based on oxidation state. Hyaluronization was demonstrated to provide the greatest resistance to protein coverage, equivalent to that of the most resistant dextranized surface. Resistance to protein adsorption was independent of the type of HA utilized. With changing bulk protein concentration from 20 to 40 μg ml(-1) for each species, Fg coverage on silicon increased by 4x, whereas both BSA and Fg adsorption on dextran and HA were far less dependent on protein bulk concentration.     

Competitive protein adsorption on polysaccharide and hyaluronate modified surfaces

Adsorption of bovine serum albumin (BSA) and fibrinogen (Fg) was measured on six distinct bare and dextran- and hyaluronate-modified silicon surfaces created using two dextran grafting densities and three hyaluronic acid (HA) sodium salts derived from human umbilical cord, rooster comb and Streptococcus zooepidemicus. Film thickness and surface morphology depended on the HA molecular weight and concentration. BSA coverage was enhanced on surfaces in competitive adsorption of BSA:Fg mixtures. Dextranization differentially reduced protein adsorption onto surfaces based on oxidation state. Hyaluronization was demonstrated to provide the greatest resistance to protein coverage, equivalent to that of the most resistant dextranized surface. Resistance to protein adsorption was independent of the type of HA utilized. With changing bulk protein concentration from 20 to 40 μg ml^?1 for each species, Fg coverage on silicon increased by 4x, whereas both BSA and Fg adsorption on dextran and HA were far less dependent on protein bulk concentration.     

Characterization of very dense mineral oxide–gel composites for fluidized-bed adsorption of biomolecules

Efficient design of fluidized-bed biomolecule adsorption from crude feed stock requires particles with elevated density, large adsorption capacity and broad chemical stability. Moreover, combinations of small particle diameters with high densities allow for high fluidization velocities while preserving a rapid mass transfer.This approach has been implemented by combining stable porous mineral oxide of high density (2.2, 4.7, 5.7, 9.4 g/ml) with functionalized hydrogels. The cross-linked hydrogel derivative fills the internal porosity of the beads and provides a high equilibrium binding capacity.Various porous mineral oxides (silica, titania, zirconia and hafnia) have been characterized in term of fluidization behavior, surface reactivity and chemical resistance to harsh CIP procedures. Porous zirconia particles were also modified into ion-exchangers by suitable surface modification and intraparticle polymerization of functionalized stable derivatives of acrylic monomers. Back-mixings in fluidized bed columns were analyzed by residence time distribution analysis of inert tracers. 328 and 218 mixing plates per meter were found for respectively, bed expansions of 1.7 and 2.9. The dynamic protein adsorption behaviors of zirconia-based polymeric anion-exchange sorbents were obtained in fluidized-bed, using BSA as model protein. A dynamic binding capacity of 62 mg/ml was observed at a fluidizing velocity of 320 cm/h. These investigations substantiate the favorable physical and chemical characteristics anticipated for dense composite beads for use as fluidized bed adsorbents.     

Effect of Air Plasma Processing on the Adsorption Behaviour of Bovine Serum Albumin on Spin-Coated PMMA Surfaces

This paper reports the adsorption of Bovine Serum Albumin （BSA） onto Dielectric Barrier Discharge （DBD） processed Poly（methyl methacrylate） （PMMA） surfaces by a Quartz Crystal Microbalance with Dissipation monitoring （QCM-D） technique. The purpose is to study the influence of DBD processing on the nature and scale of BSA adsorption on PMMA surface in vitro. It was observed that DBD processing improves the surface wettability of PMMA film, a fact attributable to the changes in surface chemistry and topography. Exposure of the PMMA to Phosphate Buffed Saline （PBS） solution in the QCM-D system resulted in surface adsorption which reaches an equilibrium after about 30 minutes for pristine PMMA, and 90 minutes for processed PMMA surface. Subsequent injection of BSA in PBS indicated that the protein is immediately adsorbed onto the PMMA surface. It was revealed that adsorption behaviour of BSA on pristine PMMA differs from that on processed PMMA surface. A slower adsorption kinetics was observed for pristine PMMA surface, whilst a quick adsorption kinetics for processed PMMA. Moreover, the dissipation shift of protein adsorption suggested that BSA forms a more rigid structure on pristine PMMA surface that on processed surface. These data suggest that changes in wettability and attendant chemical properties and surface texture of the PMMA surface may play a significant role in BSA adsorption process.     

Analysis of protein adsorption characteristics to nano-pore silica particles by using confocal laser scanning microscopy

The effect of average pore size of nano-pore silica particles on protein adsorption characteristics was determined experimentally by the dissociation constant and the adsorption capacity determined from the Langmuir equation. As the average pore size was increased from 2.2 to 45 nm, the BSA adsorption capacity increased from 16.8 to 84.3 mg/g-silica so as the equilibrium constant (from 2.6 to 9.4 mg/ml). Using confocal microscopy with fluorescence labeling, we could visualize the protein adsorption in situ and determine the minimum pore size required for efficient intraparticle adsorption. The confocal microscopy analysis revealed that BSA was adsorbed mainly on the surface of the particles with a smaller pore size, but diffused further into the interstitial surface when it was sufficiently large. It was concluded that for BSA whose Stoke's diameter is ca. 3.55 nm the minimum pore size of about 45 nm or larger was required for a sufficient adsorption capacity.     

A quantitative and selective chromatography method for determining coverages of multiple proteins on surfaces

Competitive protein adsorption plays a key role in the surface hemocompatibility of biological implants. We describe a quantitative chromatography method to measure the coverage of multiple proteins physisorbed to surfaces. In this method adsorbed proteins are displaced by CHAPS (3-[(3-cholamidopropyl)dimethylammonio]-1-propanesulfonate) and then analyzed by high performance liquid chromatography to separate and quantify the individual proteins, in this case bovine serum albumin (BSA) and bovine fibrinogen (Fg). CHAPS displaced over 95% of the adsorbed proteins and was easily removed from solution by dialysis. This method was tested by measuring the coverage of BSA, 66 kDa, and Fg, 340 kDa, simultaneously adsorbed from solutions with concentration of 20 microg/ml, on bare and dextranized silicon. Relative to silicon, the dextranized surfaces were found to strongly inhibit protein adsorption, decreasing BSA and Fg coverages by 76 and 60%, respectively.     

Expanded and packed bed albumin adsorption on fluoride modified zirconia

The expanded bed characteristics of 75-103microm fluoride-modified zirconia (FmZr) particles synthesized by a fed batch oil emulsion process were investigated. These particles are distinguished from commercially available expanded-bed adsorbents by virtue of their high density (2.8 g/cc) and the mixed mode protein retention mechanism which allows for the retention of both cationic and anionic proteins. The linear velocity versus bed porosity data agree with the Richardson-Zaki relationship with the terminal velocity in infinite medium of 2858.4 cm/h and a bed expansion index of 5.1. Residence time distribution (RTD) studies and bovine serum albumin (BSA) adsorption studies were performed as a function of the height of the settled bed to the column diameter (H:D) ratio and degree of bed expansion with superficial velocities of 440 to 870 cm/h. The settled bed, a 2x expanded bed, and a 3x expanded bed were studied for the H:D ratios of 1:1, 2:1, and 3:1. The dynamic binding capacity (DBC) at 5% breakthrough was low (2-8 mg BSA/mL settled bed) and was independent of the H:D ratio or the degree of bed expansion. The saturation DBC was 32.3 +/- 7.0 mg BSA/mL settled bed. The adsorption-desorption kinetics and intraparticle diffusion for protein adsorption on FmZr (38-75 micrometer) were investigated by studying the packed bed RTD and BSA adsorption as a function of temperature and flow rate. The data show that the adsorption-desorption kinetics along with intraparticle diffusion significantly influence protein adsorption on FmZr. Low residence times ( approximately 0.8 min) of BSA result in a DBC at 5% breakthrough which is 3.5-fold lower compared to that at 6-fold higher protein residence time. At low linear velocity (45 cm/h) the breakthrough curve is nearly symmetrical and becomes asymmetrical and more dispersed at higher linear velocity (270 cm/h) due to the influence of slow adsorption-desorption kinetics and intraparticle diffusion.Copyright 1998 John Wiley & Sons, Inc. Bioeng 60: 333-340, 1998.     

Protamine assembled in multilayers on colloidal particles can be exchanged and released

Biocomposite thin films assembled on colloidal particles by means of layer-by-layer adsorption have been suggested as drug carriers and diagnostic devices. Protamine (PRM)/dextransulfate (DXS) and protamine/bovine serum albumine (BSA) multilayers were fabricated on colloidal silica and subsequently investigated by means of fluorescence activated cell sorting (FACS) and microelectrophoresis. Fluorescein labeled polyelectrolytes were embedded at different positions in the multilayers as a marker for layer growth. FACS showed that PRM and DXS formed regular growing stable multilayers, yet adsorbed PRM can be nevertheless exchanged with PRM in solution during layer formation and also after the multilayer formation has been completed. Up to 90% of the PRM pool was available for exchange. PRM together with BSA as demonstrated by SFM did not form multilayers under the applied conditions although the zeta-potential, commonly used as an indicator for stepwise adsorption, observed characteristic alternations. The capability of bound PRM to exchange with PRM in solution is attributed to its relatively small size. The demonstrated exchange may have importance in designing multilayers with smart release features. Furthermore, FACS proved to be a rather suitable means to quantify the aggregation behavior during coating and washing. Singulets, doublets, triplets, and aggregates of higher order could be clearly resolved. The aggregation of particles coated with PRM/DXS layers was higher than that of silica particles coated with PAH/PSS layers. In the first case about 50% of all recorded events are attributed to aggregats, while the PAH/PSS coating produced only about 10% aggregates.     

Expanded bed adsorption of human serum albumin from very dense Saccharomyces cerevesiae suspensions on fluoride-modified zirconia.

The adsorption of proteins from high cell density yeast suspensions on mixed-mode fluoride-modified zirconia (FmZr) particles (38 to 75 microm, surface area of 29 m(2)/g and density of 2.8 g/cm(3)) was investigated using human serum albumin (HSA) added to Saccharomyces cerevesiae as the model expression host. Because of the high density of the porous zirconia particles, HSA (4 mg/mL) can be adsorbed from a 100 g dry cell weight (DCW)/L yeast suspension in a threefold-expanded bed of FmZr. The expanded bed adsorption of any protein from a suspension containing >50 g DCW/L cells has not been previously reported. The FmZr bed expansion characteristics were well represented by the Richardson-Zaki correlation with a particle terminal velocity of 3.1 mm/s and a bed expansion index of 5.4. Expanded bed hydrodynamics were investigated as a function of bed expansion using residence time distribution studies with sodium nitrite as the tracer. The adsorption of HSA on FmZr exhibited features of multicomponent adsorption due to the presence of dimers. The protein binding capacity at 5% breakthrough decreased from 22 mg HSA/mL settled bed void volume for 20 g DCW/L yeast to 15 mg HSA/mL settled bed void volume for 40 g DCW/L yeast and remained unchanged for the higher yeast concentrations (60 to 100 g DCW/L). However, the batch (or equilibrium) binding capacity decreased monotonically as a function of yeast concentration (20 to 100 g DCW/L) and the binding capacity at 100 g DCW/L yeast was fivefold lower compared with that at 20 g DCW/L yeast. The lower batch binding capacity at high cell concentrations resulted from the adsorption of cells at the surface of the particles restricting access of HSA to the intraparticle surface area. Batch (or equilibrium) and column HSA adsorption results indicated that the adsorption of HSA on FmZr occurred at a time scale that may be much faster than that of yeast cells. The zirconia particles were cleaned of adsorbed HSA and yeast with a total of 1500 to 2000 column volumes (over many cycles) of 0. 25 M NaOH, without any significant effect on the chromatographic performance.     

Particle-by-particle quantification of protein adsorption onto poly(ethylene glycol) grafted surfaces

The use and advantage of flow cytometry as a particle-by-particle, low sampling volume, high-throughput screening technique for quantitatively examining the non-specific adsorption of proteins onto surfaces is presented. The adsorption of three proteins: bovine serum albumin (BSA), immunoglobulin gamma (IgG) and protein G, incubated at room temperature for 2 h onto organosilica particles modified with poly(ethylene glycol) (PEG) of increasing MW (2000, 3400, 6000, 10,000 and 20,000 g mol(-1)) and grafted amounts (0.14-1.4 mg m(-2)) was investigated as a model system. Each protein exhibited Langmuir-like, high affinity monolayer limited adsorption on unmodified particles with the proteins reaching surface saturation at 1.8, 4.0 and 2.5 mg m(-2) for BSA, IgG and protein G, respectively. Protein adsorption on PEG-modified surfaces was found to decrease with increasing amounts of grafted polymer. PEG grafting amounts >0.6 mg m(-2) effectively prevented the adsorption of the larger two proteins (BSA and IgG) while a PEG grafting amount >1.3 mg m(-2) was required to prevent the adsorption of the smaller protein G.     

Adsorptive immobilization of a Pseudomonas strain on solid carriers for augmented decolourization in a chemostat bioreactor

Pseudomonas GM3, a highly efficient strain in cleavage of azo bonds of synthetic dyes under anoxic conditions, was immobilized via adsorption on two types of carriers, porous glass beads and solid PVA particles. The cells were cultivated in a nutrient medium, adsorbed on sterile carriers, stabilized as biofilms in repeated batch cultures, and introduced into a chemostat activated sludge reactor for augmented decolourization. The microbial cells were quickly adsorbed and fixed on the PVA surface, compared to a slow and linear immobilization on the glass surface. The porous structure of glass beads provided shelter for the embedded cells, giving a high biomass loading or thick biofilm (13.3 mg VS ml-1 carrier) in comparison with PVA particles (4.8 mg VS ml-1 carrier), but the mass transfer of substrate in the biofilm became a significant limiting factorin the thicker biofilms (effectiveness factor eta = 0.31). The microbial decolourization rate per volume of carriers was 0.15 and 0.17 mg dye ml-1 of glass beads and PVA particles, respectively. In augmented decomposition of a recalcitrant azo dye (60 mg l-1), the immobilized Pseudomonas cells in porous glass beads gave a stable decolourization efficiency (80-81%), but cells fixed on solid PVA particles showed an initial high colour removal of 90% which then declined to a stable removal efficiency of 81%. In both cases, the colour removal efficiency of the chemostat bioreactor was increased from < 10% by an activated sludge to approximately 80% by the augmented system.     

Adsorption of gamma-globulin, a model protein for antibody, on colloidal particles

The effect of surface properties on the adsorption of bovine gamma-globulin, a model protein for antibody, was studied. Polystyrene latex (PS), hydrophilic copolymer lattices of styrene/2-hydroxyethyl methacrylate [P(S/HEMA)], styrene/ methacrylic acid [P(S/MAA)] and methyl methacrylate/ 2-hydroxyethyl methacrylate [P(MMA/HEMA)], and colloidal silica were used. The adsorption isotherms of gamma-globulin on these colloidal particles were measured as a function of pH and ionic strength. The hydrophilic particles showed low affinities for gamma-globulin at alkaline pH, while PS showed high affinities for gamma-globulin over the whole range of pH and ionic strength. The gamma-globulin adsorption on hydrophilic particles was highly reversible with respect to the pH and ionic strength compared with that on PS. These differences indicate that the dominant driving forces of adsorption are related to the hydrophilicity of particles. The adsorption isotherms of all colloidal particles showed the plateau values, and the order of maximum values of plateau adsorption was P(S/MAA) > PS or P(S/HEMA), silica > P(MMA/HEMA). Thus, they were also affected by the charged groups and the hydrophilicity of the surfaces. On the other hand, the plateau values of all colloidal particles were more or less symmetrical with a maximum at around the isoelectric point of gamma-globulin at an ionic strength of 0.01. This behavior is attributed to the important role of the lateral interaction between the adsorbed molecules at low ionic strength.     

Molecular mechanism of polyethylene glycol mediated stabilization of protein

The effect of different molar ratios of polyethylene glycol (PEG) on the conformational stability of protein, bovine serum albumin (BSA), was studied. The binding of PEG with BSA was observed by fluorescence spectroscopy by measuring the fluorescence intensity after displacement of PEG with chromophore ANS and had further been confirmed by measuring the intrinsic fluorescence of tryptophan residues of BSA. Co-lyophilization of BSA with PEG at optimum BSA:PEG molar ratio led to the formation of the stable protein particles. Circular dichroism (CD) spectroscopy study suggested that a conformational change had occurred in the protein after PEG interaction and demonstrated the highest stability of protein at the optimum BSA:PEG molar ratio of 1:0.75. Additional differential scanning calorimetry (DSC) study suggested strong binding of PEG to protein leading to thermal stability at optimum molar ratio. Molecular mechanism operating behind the polyethylene glycol (PEG) mediated stabilization of the protein suggested that strong physical adsorption of PEG on the hydrophobic core of the protein (BSA) along with surface adsorption led to the stability of protein.     

Characterization of the surfaces generated by liposome binding to the modified dextran matrix of a surface plasmon resonance sensor chip

The dextran matrix of a surface plasmon resonance (SPR) sensor chip modified with hydrophobic residues (BIAcore sensor chip L1) provides an ideal substrate for liposome adsorption. Liposomes of different lipid compositions are captured on the sensor chips by inserting these residues into the liposome membrane, thereby generating stable lipid surfaces. To gain a more detailed understanding of these surfaces, and to prove whether the liposomes stay on the matrix as single particles or form a continuous lipid layer by liposome fusion, we have investigated these materials, using atomic force microscopy (AFM) and fluorescence microscopy. Force measurements with AFM probes functionalized with bovine serum albumin (BSA) were employed to recognize liposome adsorption. Analysis of the maximal adhesive force and adhesion energy reveals a stronger interaction between BSA and the dextran matrix compared to the lipid-covered surfaces. Images generated using BSA-coated AFM tips indicated a complete and homogeneous coverage of the surface by phospholipid. Single liposomes could not be detected even at lower lipid concentrations, indicating that the liposomes fuse and form a lipid bilayer on the dextran matrix. Experiments with fluorescently labeled liposomes concurred with the AFM studies. Surfaces incubated with liposomes loaded with TRITC-labeled dextran showed no fluorescence, indicating a complete release of the encapsulated dye. In contrast, surfaces incubated with liposomes containing a fluorescently labeled lipid showed fluorescence.     

Microwave-aided binding of gold-protein-ligand (GPL) complexes. Light microscopic observations in the rat brain.

We describe a rapid method for the preparation and binding site labeling of cryostat sections for use in light microscopy. Instead of using antibodies to bind to specific sites, substance P, delta-sleep-inducing peptide, oxytocin, and dopamine were covalently attached to BSA and then the BSA-ligand complex was adsorbed on 5-nm colloidal gold particles. Bioassays carried out on isolated organs indicated that the physiological activity of the ligand GPL complex was maintained. Most of the technical steps included use of an ordinary microwave oven (MWO), with tissues exposed for less than 1 min in any given step. Cryostat sections of unfixed rat brain were pre-incubated for 50 sec in the MWO in a Tris-buffered solution (pH 7.4) containing 1.5% BSA, then further incubated for 50 sec in the MWO in Tris-buffered solution containing 1% gelatin and the diluted colloidal gold suspension. After washing, the preparations were postfixed for 30 sec in the MWO in 5% formaldehyde solution, pH 7.4. Finally, the cell-bound gold particles were enlarged by a silver-enhancing process and counterstained. Preparations observed at high magnification provided excellent resolution of the cell binding sites. Positive and negative controls performed by addition of BSA-conjugated ligands to the pre-incubation and incubation medium, and displacement of the markers by an excess of unbound ligand in the pre-incubation or the incubation medium, showed the specificity of the tissue labeling.     

Sequential adsorption of F(ab')(2) and BSA on negatively and positively charged polystyrene latexes

The aim of the present work is to study the sequential adsorption of F(ab')(2) and bovine serum albumin (BSA) molecules adsorbed onto positively and negatively charged polystyrene latexes. Cationic and anionic latexes were prepared by emulsifier-free emulsion polymerization. Adsorptions of F(ab')(2) on both latexes at a low ionic strength and different pHs were performed. The cationic latex showed a higher adsorption of F (ab')(2) molecules over a range of pH, which could be due to the formation of multilayers. Sequential adsorption of anti-CRP F(ab')(2) and monomeric BSA were performed at two different pre-adsorbed F(ab')(2) amounts on both types of latex. Displacement of F(ab')(2) occurred only when the preadsorbed amounts were larger than a certain critical value, which depends on the adsorption pH. A greater displacement of larger preadsorbed amounts might be the result of a weaker contact between the protein molecules and the polystyrene surface. The displacement of F(ab')(2) previously adsorbed onto both latexes occurred due to pH changes, an increase of ionic strength and the presence of BSA molecules. The effect caused by these three factors was studied independently. The main factors in the desorption of F(ab')(2) on the anionic latex are the changes in pH and ionic strength, whereas on the cationic latex the desorption is mainly caused by the increase of the ionic strength and the presence of BSA. The colloidal stability of the immunotatex was improved by BSA adsorption, especially on cationic latex. (c) 1995 John Wiley & Sons, Inc.     

BSA structural changes during homomolecular exchange between the adsorbed and the dissolved states

The secondary structure and the thermostability of bovine serum albumin (BSA), before adsorption and after homomolecular displacement from silica and polystyrene particles, are studied by circular dichroism spectroscopy and differential scanning calorimetry. The structural perturbations induced by the hydrophilic silica surface are reversible, i.e. BSA completely regains the native structure and stability after being exchanged. On the other hand, the adsorption on, and subsequent desorption from, polystyrene particles causes irreversible changes in the stability and (secondary) structure of BSA. The exchanged proteins have a higher denaturation temperature and a lower enthalpy of denaturation than native BSA. The alpha-helix content is reduced while the beta-turn fraction is increased in the exchanged molecules. Both effects are more pronounced when the protein is displaced from less crowded sorbent surfaces. The irreversible surface-induced conformational change may be related to some aggregation of BSA molecules after being exposed to a hydrophobic surface.     

Precise localization of antigens on follicular dendritic cells

Summary Horse-spleen ferritin or bovine serum albumin conjugated to colloidal gold (BSA-gold) were injected subcutaneously in preimmunized mice. In draining lymph nodes both antigens were located in macrophages or between the cytoplasmic processes of follicular dendritic cells (FDC). Some of the antigens remained trapped on FDC until day 31 after injection. Simultaneous injection of both antigens showed that they were located between the infoldings of the same FDC. These cells are thus able to retain at least two different antigens on their surface. The peculiar arrangement of ferritin between the cytoplasmic infoldings suggests that this antigen is fixed on both cell membranes by specific antibodies. The trapped immune complexes could thus stabilize the FDC membrane system.The antigen retention requires the presence of specific antibodies since BSA-gold or ferritin injected without preimmunization were not found between FDC processes. Nonantigenic materials, such as colloidal gold or carbon particles, are not trapped by FDC, except when injected in large amounts.The antigens were trapped on the surface of FDC, however unfrequently in close contact with lymphocytes. FDC might protect lymphocytes against an excess of immune complexes and act as regulators of contacts between lymphocytes and immune complexes.Abbreviations BSA bovine serum albumin - BSA-gold BSA conjugated to colloidal gold particles - FDC follicular dendritic cells