Reduced Methylene Blue as a Stain for Crustacean Nerves

Effective in situ staining of crustacean nerves was achieved with leuco methylene blue reduced with either ascorbic acid or sodium hydrosulfite (Na₂S₂O₄). A stock solution of methylene blue, 0.4% (ca. 0.001 M), and the reductants, ascorbic acid or sodium hydrosulfite (0.01 M), were prepared in van Harreveld's crayfish physiological solution. Methylene blue stock solution was mixed with either of the reductants in the approximate ratio of 1:10, v/v, and titrated to the end point. Ascorbic acid reduction is light catalyzed and requires intense illumination during titration. The cleared or leucomethylene blue stock solution is suitable for immediate use as a working nerve stain. With either reductant, the working solution oxidizes on standing in air, but can be titrated repeatedly without loss of staining properties. Dissected nerve trunks or tissue were immersed in the working stain for 20 min at room temperature and the staining process observed until suitable contrast developed. Excess dye was decanted and the tissues flooded with crayfish physiological solution. Contrast could sometimes be enhanced by flooding the stained area with 1% hydrogen peroxide in van Harreveld's solution. When permanent mounts were prepared, tissues were dehydrated with tertiary butyl alcohol in preference to ethyl alcohol series. For anatomical and neurophysiological studies of nerve distribution in crustaceans, the alternative use of either ascorbic acid or sodium hydrosulfite, as reductants for methylene blue, was preferable to the more complicated rongalit-technique and characterization of neural elements was fully as satisfactory.     

Zinc Chloride Methylene Blue, Ii. Preparation of Giesma and Wright Type Low Azure B Blood Stains from Dichromate Oxidized Commercial Dye

TO determine the amount of K₂Cr₂O₇ required to produce optimal Giemsa type staining, six 1 g amounts (corrected for dye content) of zinc methylene blue were oxidized with graded quantities of K₂Cr₂O₇ to produce 4, 8, 12, 16, 20 and 24% conversion of methylene blue to azure B. These were heated with a blank control 15 minutes at 100 C in 60-65 ml 0.4 N HCI. cooled, and adjusted to 50 ml to give 20 mg original dye/ml. Aliquots were then diluted to 1% and stains were made by the “Wet Giemsa” technic (Lillie and Donaldson 1979) using 6 ml 1% polychrome methylene blue, 4 ml 1% cosin (corrected for dye content), 2 ml 0.1 M pH 6.3 phosphate buffer, 5 ml acetone, and 23 ml distilled water. The main is added last and methanol fixed blood films are stained immediately for 20-40 min.

For methylene blue supplied by MCB 12-H-29, optimal stains were obtained with preparations containing 20 and 24% conversion of methylene blue to azure B. With methylene blue supplied by Aldrich (080787), 16% conversion of methylene blue to azure B was optimal. Eosinates prepared from a low azure B/methylene blue preparation selected in this way give good stains when used as a Wright stain in 0.3% methanol solution. However, when the 600 mg eosinate solution in glycerol methanol is supplemented with 160 mg of the same azure B/methylene blue chloride the mixture fails to perform well. The HCI precipitation of the chloride apparently produces the zinc methylene blue chloride salt which is poorly soluble in alcohol. It appears necessary to have a zinc-free azure B/methylene blue chloride to supplement the probably zinc-free eosinate used in the Giemsa mixture.     

Methylene Violet (Bernthsen), by Zinc-Alkali-Chlorate Hydrolysis of Methylene Blue

Though Bernthsen's methylene violet (MV) is a common constituent of polychrome methylene blue, the hydrolytic oxydation of methylene blue to yield azure-free MV has been considered a difficult chemical reaction since the time of Bernthsen, who used Ag₂O in the hydrolysis. MV is qualitatively distinguished from azures by Bernthsen's criteria and the author's new tests: (1) light-excited isomeric change, (2) reactivity to acidity, (3) reaction with KCIO, and (4) reaction with Na₂SO₃ of azures in CHCI₃, while MV gives none. But MV shows (5) indicator properties at pH 4, while azures do not. For practical hydrolysis, treat methylene blue (10 parts by weight) and KCIO₃ (1 part) with 1-2 N NaOH to convert methylene blue to a mixture of MV and azures. Then dilute the solution, add a Zn salt and NaHCO₃ in excess of the amount needed to convert the NaOH to Na₂CO₃. Boil the solution gently for 1-2 hr. The end point of the reaction is found by pipetting a drop of reactant into 3% acetic acid in a test tube, adding CHC1₃ and extracting. The acetic layer should then be almost colorless while the CHC1₃ is colored intensely cherry red. After cooling, the precipitated dye is filtered and dried. This procedure gives good yields of a dye which meets the criteria given by Bernhsen. The peak of the absorption curve in solution, pH 4-11, is at 624 mμ (Bernthsen 625 mμ) and in acid solution, pH 0-4, 588 mμ (Biological Stains, 1953; 580 μ). The dye contains so little azures, that purification of the MV fraction obtained from the reaction mixture is unnecessary when it is used in the Wright-type Romanowsky stain. The remarkable staining effect of MV is its power to bring out red azurophil granules of monocytes and lymphocytes when used with eosinated thiazins in Wright's stain.     

Direct Staining of Reticular Fibers with Gold Chloride

Reticular fibers are selectively stained in paraffin sections of formalin-fixed or Bouin's-fixed tissue as follows: 1% aqueous solution of gold chloride for 20 min, followed by a 10 min immersion in an aqueous solution containing 5% Na₂CO₃ and 0.5% KOH. The sections then are placed in a 5% aqueous solution of KI for 2 min. Counterstaining with a 0.25% aqueous solution of methylene blue chloride is optional. The reticular fibers stain dark pink; the collagen bundles are a light pink to straw color without the counterstain, or a light blue color when the methylene blue is used.     

Composition of J.S.B. stain and Factors Affecting its Quality

Several samples of J.S.B. stain (Jaswant Singh and Bhattacharjee, 1944) solution 1 (polychrome methylene blue) were prepared with 3-8 hr for dichromate-acid oxidation and addition of varying quantities of Na₂HPO₄ buffer for pH adjustment. Storage under severe tropical conditions and periodical checks by staining Plasmodium cynomolgi smears revealed that staining solutions oxidized 6-7 hr with a final pH of 7.8 gave optimum results. Some precipitation of azures, due to heat after 5 mo, adversely affected the quality of staining solutions, while cooler storage conditions were most favorable. Spectrophotometric and chromatographic studies indicated that the J.S.B. solution 1 was composed of blue and purple components, corresponding to higher methylene azures with methylene blue and thionin with allied products respectively.     

Staining of Nerve Fibers with Methylene Blue Factors Improving the Staining

Several factors influencing the staining of nerve fibers with methylene blue, especially the influence of chloralhydrate and carbamylcholine chloride (as parasympathicotonics), and of some anesthetics were studied. The intestines of mouse, rat, and guinea pig were used. The following immersion technic is suggested: Tissue from animals anesthetised by chloralhydrate is immersed in: zinc free methylene blue, 0.03%; sodium tartrate, 0.5%; sodium pyruvate, 0.05% carbamylcholine, 0.00005%; 0.2 M Na₂HPO₄, 0.77%; 0.1 M citric acid, 0.18%; NACl, 0.79%; also an anesthetic which varies with the animal selected. Air is kept bubbling through the staining solution and microscopic examination is made at 6 min. intervals. After 0.5-1 hr. the tissue is fixed in: ammonium molyb-date, 10 g.; sucrose, 35 g.; distilled water, 100 ml.; to which is added just before use, 1% platinum chloride, 3 ml.; 2% osmic acid, 3 drops. Washing is in ice cold water and dehydration at 0°C. in Lang's fluids (varying mixtures of ethanol and n-butanol). The tissues thus prepared are stored in liquid paraffin.     

Borax Methylene Blue: A Spectroscopic And Staining Study

Borax methylene blue is quite stable at room temperatures of 22-25 C. At 30 C polychroming is slow; during 50 days in a water bath at this temperature the absorption peak moves from 665 to 656 nm. At 35 C, the absorption peak reaches 660 nm in 7 days, 654 nm in 14. At 60 C polychroming is rapid, the absorption peak reaching 640-620 nm in 3 days. When the pH of the borax methylene blue solutions, normally about 9.0, is adjusted to pH 6.5, the absorption peak remains at 665 nm even when incubated at 60 C for extended periods.

When used as a blood stain 0.4 ml borax methylene blue (1% methylene blue in 1% borax), 4 ml acetone, 2 ml borax-acid phosphate buffer to bring the solution to pH 6.5, and distilled water to make 40 ml, with 0.2 ml 1% eosin added just before using, an excellent Nocht-Giemsa type stain is achieved after 30 minutes staining. The material plasmodia P. falciparum, P. vivax, and P. berghei stain moderate blue with dark red chromatin and green to black pigment granules.

The study confirms Malacnowski's 1891 results and explains Gautier's 1896-98 failure to duplicate it.     

A Basic Fuchsin and Alkalinized Methylene Blue Rapid Stain for Epoxyembedded Tissue

Sections 1 μ thick of epoxy-embedded, OsO₄-fixed tissues were stained with 4% aqueous basic fuchsin at 70 C for 1 min, rinsed well and destained, also at 70 C, for 1 min. A 2% aqueous methylene blue solution, alkalinized to pH 12.5 by mixing 1 N NaOH with the dye on the slide in the proportion of about 2:1, was then allowed to act for 2 min at 23-27 C. The stain was rinsed off the slide, and the preparation air dried before applying a mounting medium and cover glass. The mounting medium consisted of immersion oil sealed with epoxy household cement. Stains had not faded after 1 yr. The method is simple, rapid (total time 4-5 min), and provides sharp contrast between cellular and connective tissue components.     

Reduced Methylene Blue as a Stain for Crustacean Nerves

Effective in situ staining of crustacean nerves was achieved with leuco methylene blue reduced with either ascorbic acid or sodium hydrosulfite (Na₂S₂O₄). A stock solution of methylene blue, 0.4% (ca. 0.001 M), and the reductants, ascorbic acid or sodium hydrosulfite (0.01 M), were prepared in van Harreveld's crayfish physiological solution. Methylene blue stock solution was mixed with either of the reductants in the approximate ratio of 1:10, v/v, and titrated to the end point. Ascorbic acid reduction is light catalyzed and requires intense illumination during titration. The cleared or leucomethylene blue stock solution is suitable for immediate use as a working nerve stain. With either reductant, the working solution oxidizes on standing in air, but can be titrated repeatedly without loss of staining properties. Dissected nerve trunks or tissue were immersed in the working stain for 20 min at room temperature and the staining process observed until suitable contrast developed. Excess dye was decanted and the tissues flooded with crayfish physiological solution. Contrast could sometimes be enhanced by flooding the stained area with 1% hydrogen peroxide in van Harreveld's solution. When permanent mounts were prepared, tissues were dehydrated with tertiary butyl alcohol in preference to ethyl alcohol series. For anatomical and neurophysiological studies of nerve distribution in crustaceans, the alternative use of either ascorbic acid or sodium hydrosulfite, as reductants for methylene blue, was preferable to the more complicated rongalit-technique and characterization of neural elements was fully as satisfactory.     

Borax methylene blue: a spectroscopic and staining study.

Borax methylene blue is quite stable at room temperatures of 22-25 C. At 30 C polychroming is slow; during 50 days in a water bath at this temperature the absorption peak moves from 665 to 656 nm. At 35 C, the absorption peak reaches 660 nm in 7 days, 654 nm in 14. At 60 C polychroming is rapid, the absorption peak reaching 640-620 nm in 3 days. When the pH of the borax methylene blue solutions, normally about 9.0, is adjusted to pH 6.5, the absorption peak remains at 665 nm even when incubated at 60 C for extended periods. When used as a blood stain 0.4 ml borax methylene blue (1% methylene blue in 1% borax), 4 ml acetone, 2 ml borax-acid phosphate buffer to bring the solution to pH 6.5, and distilled water to make 40 ml, with 0.2 ml 1% eosin added just before using, an excellent Nocht-Giemsa type stain is achieved after 30 minutes staining. The material plasmodia P. falciparum, P. vivax, and P. berghei stain moderate blue with dark red chromatin and green to black pigment granules. The study confirms Malachowski's 1891 results and explains Gautier's 1896-98 failure to duplicate it.     

Differential in Toto Staining of Bone, Cartilage and Soft Tissues

The following method for staining bone and cartilage allows study of the gross cleared specimen and does not injure the tissues for subsequent microscopic study: Fix in 10% neutral formalin; bleach thoroughly in 3% H₂O₂ in sunlight. Wash in distilled water. Stain bone 24 hours in 0.01 g. of Biebrich scarlet in 100 ml. of distilled water. Destain in 95% alcohol until soft tissues and cartilage are colorless. Stain cartilage 24 hours in a pH2 buffer solution of 2.1g. of citric acid per 100 ml. of water with 0.001 g. of methylene blue. Destain in pH2 buffer solution until soft tissues are pale. Dehydrate in two changes of 95% alcohol in preparation for clearing. (This completes the destaining and may remove too much stain from the cartilage if destaining in the pH2 solution has been carried too far.) Place in Groat's clearing fluid and cover loosely so that the alcohol may evaporate, or remove the alcohol in vacuo. Groat's Mixture No. 19 is usually satisfactory.

For a combined stain, first stain bone, as above, and then apply the cartilage stain.

Seal jars with an ordinary liquid wood glue such as LePage's.     

Phloxine-Methylene Blue Staining of Formalin-Fixed Tissue

It is at present difficult to obtain a good phloxine-metbylene blue stain on formalin-fixed tissue. When phloxine has been used, it is washed out in the process of staining with methylene blue and differentiating with colophony (rosin). In the original technic of Mallory, Zenker's fixation is used. The tissue is first stained with a 2.5% aqueous solution of phloxine, then with a solution of 1% methylene blue plus 1% azure II and differentiated in colophony.¹     

Localization of methylene blue paramolybdate in vitally stained nerves

Methylene blue taken up by living neurons can be preserved for electron microscopy in a fixative containing osmium tetroxide and ammonium paramolybdate at pH 5.2. Paramolybdate is the buffer, precipitating agent and main osmotic ingredient; it does not function as an electron stain unless methylene blue is present. The low pH keeps the dye/paramolybdate complex from dissolving. Neither the low pH nor drastic dehydration from water to absolute ethanol harm the tissue. The staining mechanism involves cationic methylene blue associating with anionic structures such as microtubules and neurofilaments in the living cell; during fixation paramolybdate forms a precipitate with the dye at the staining sites. This fixative does not preserve microtubules unless they are first vitally stained.     

Staining and Mounting Helminths

The following procedure is recommended: Fix ces-todes and trematodes (while held flat between glass slides) 0.5-2.0 hr. in the following mixture: formalin, 15; acetic acid (gl.), 5; glycerol, 10; 95% ethyl alcohol, 24; distilled H₂O, 46; all proportions by volume. After freeing them from the slides, wash thoroughly in running water and stain immediately thereafter. Stock staining solution: ferric ammonium alum (violet cryst.), 2 g.; distilled H₂O (cold) 100 ml.; after solution, add 2 ml. concentrated H₂SO₄, bring to a boil; add 1 g. coelestin blue B (Nat. Aniline), boil 3-5 min.; cool and add 10 ml. absolute methyl alcohol and 10 ml. glycerol. Dilute 1 vol. with 3 vol. distilled H20 for use. Stain 5-30 min., depending on size of specimens. Wash with 2 changes 0.5 hr. each of distilled H₂O, then 50% isopropyl alcohol 12-16 hr., 50% isopropyl alcohol 2 hr., followed by graded isopropyl alcohol for dehydration. Ether: ethyl alcohol (equal parts), 1 hr., is followed by embedding in celloidin in a sheet just thick enough to cover the specimens. Trim embedded specimens and dehydrate with isopropyl alcohol, 80%, 90% and absolute. Clear in beechwood creosote. Mount in balsam with cover glasses that overlap the edges of the celloidin 1-2 mm. While drying at 37°C, refill edges of mount with fresh balsam as needed. When dry, remove excess balsam and ring the edges with ordinary gloss enamel paint.     

Preparation of Large Epoxy Sections for Light Microscopy as an Adjunct to Fine-Structure Studies

Tissue blocks 2 × 2 × 0.4 cm were fixed 6-24 hr in phosphate-buffered 5% glutaraldehyde then sliced to 2 × 2 × 0.1 cm and soaked in 0.1 phosphate-buffer (pH 7.3) for at least 12 hr. Fixation was continued for 2 hr in phosphate-buffered 1-2% OsO₄. The slices were dehydrated, infiltrated with Araldite, and embedded in flat-bottomed plastic molds. Sectioning at 1-8 μ with a sliding microtome was facilitated by addition of 10% dibutylphthalate to the standard epoxy mixture. The sections were spread on warm 1% gelatin and attached to glass slides by drying, baking at 60 C, fixing in 10% formalin or 5% glutaraldehyde and baking again. Sections were mordanted in 5% KMnO₄ (5 min), bleached with 5% oxalic acid (5 min) and neutralized in 1% Li₂CO₃ (1 min). Several stains could then be applied: azure B, toluidine blue, azure B-malachite green, Stirling's gentian violet, MacCallum's stain (modified), tribasic stain (modified) and phosphotungstic acid-hematoxylin. Nuclei, mitochondria, specific granules, elastic tissue or collagen were selectively emphasized by appropriate choice of staining procedures, and cytologic detail in 1-3 μ sections was superior to that shown by conventional methods. Selected areas from adjacent 4-8 μ sections could be re-embedded for ultramicrotomy and electron microscopy.     

Staining Mitochondria With Hematoxylin After Formalin-Sublimate Fixation; A Rapid Method

Mitochondria were stained in liver, kidney, pancreas, adrenal and intestinal mucosa of rat and mouse. Tissues 1 mm thick, were fixed in a mixture of saturated aqueous HgCl₂, 90 ml; formalin (37-38% HCHO), 10 ml, at room temperature (25°C) for 1 hr. Deparaffinized sections 3-4μ thick were treated with Lugol's iodine (U.S.P.) followed by Na₂S₂O₃ (5%), rinsed in water and the ribonucleic acid removed by any of the following procedures: 0.2 M McIlavaine's buffer, pH 7.0, 2 hr, or 0.2 M phosphate buffer, pH 7.0, 2 hr at 37°C; 0.1% aqueous ribonuclease, 2 hr at 37°C; 5% aqueous trichloracetic acid overnight at 37°C; or 1% KOH at room temperature for 1 hr. After washing in water, sections were treated with a saturated solution of ferric ammonium alum at 37°C for 8-12 hr and colored by Regaud's ripened hematoxylin for 18 hr. They were then differentiated in 1% ferric ammonium alum solution while under microscopic observation.     

Differentiated Staining of Osmium Tetroxide-Fixed, Vestopal-w-Embedded Tissue in thin Sections

Tissues were fixed at 20° C for 1 hr in 1% OsO₄, buffered at pH 7.4 with veronal-acetate (Palade's fixative), soaked 5 min in the same buffer without OsO₄, then dehydrated in buffer-acetone mixtures of 30, 50, 75 and 90% acetone content, and finally in anhydrous acetone. Infiltration was accomplished through Vestopal-W-acetone mixtures of 1:3, 1:1, 3:1 to undiluted Vestopal. After polymerisation at 60° C for 24 hr, 1-2 μ sections were cut, dried on slides without adhesive, and stained by any of the following methods. (1) Mayer's acid hemalum: Flood the slides with the staining solution and allow to stand at 20°C for 2-3 hr while the water of the solution evaporates; wash in distilled water, 2 min; differentiate in 1% HCl; rinse 1-2 sec in 10% NH,OH. (2) Iron-trioxyhematein (of Hansen): Apply the staining solution as in method 1; wash 3-5 min in 5% acetic acid; restain for 1-12 hr by flooding with a mixture consisting of staining solution, 2 parts, and 1 part of a 1:1 mixture of 2% acetic acid and 2% H₂SO₄ (observe under microscope for staining intensity); wash 2 min in distilled water and 1 hr in tap water. (3) Iron-hematoxylin (Heidenhain): Mordant 6 hr in 2.5% iron-alum solution; wash 1 min in distilled water; stain in 1% or 0.5% ripened hematoxylin for 3-12 br; differentiate 8 min in 2.5%, and 15 min in 1% iron-alum solution; wash 1 hr in tap water. (4) Aceto-carmine (Schneider): Stain 12-24 hr; wash 0.5-1.0 min in distilled water. (5) Picrofuchsin: Stain 24-48 hr in 1% acid fuchsin dissolved in saturated aqueous picric acid; differentiate for only 1-2 sec in 96% ethanol. (6) Modified Giemsa: Mix 640 ml of a solution of 9.08 gm KH₂PO₄ in 1000 ml of distilled water and 360 ml of a solution of 11.88 gm Na₂HPO₄-2H₂O in 1000 ml of distilled water. Soak sections in this buffer, 12 hr. Dissolve 1.0 gm of azur I in 125 ml of boiling distilled water; add 0.5 gm of methylene blue; filter and add hot distilled water until a volume of 250 ml is reached (solution “AM”). Dissolve 1.5 gm of eosin, yellowish, in 250 ml of hot distilled water; filter (solution “E”). Mix 1.5 ml of “AM” in 100 ml of buffer with 3 ml of “E” in 100 ml of buffer. Stain 12-24 hr. Differentiate 3 sec in 25 ml methyl benzoate in 75 ml dioxane; 3 sec in 35 ml methyl benzoate in 65 ml acetone; 3 sec in 30 ml acetone in 70 ml methyl benzoate; and 3 sec in 5 ml acetone in 95 ml methyl benzoate. Dehydrated sections may be covered in a neutral synthetic resin (Caedax was used).     

Initial and Persisting Staining power of Solutions of Iron-Hematoxylin Lake

A study was made of factors affecting the initial staining power and the stability of iron-hematoxylin lake solutions. The findings were applied to the preparation of a superior hematoxylin staining solution. This is made up as follows: in 50 ml. water dissolve, in order, 1.0 g. ferric ammonium sulfate [FeNE₄ (SO₄)₂⋅ 12H₂O], 0.8 ml. sulfuric acid, 50 ml. 95% ethyl alcohol, 0.5 g. hematoxylin. Filter the solution to remove the insoluble, white crust of the ferric ammonium sulfate. The solution stains well ten minutes after it has been made. Peak performance is attained within 5 hours, and is maintained for 4 to 8 weeks. Staining time is 3 to 30 minutes. Excess stain can be rinsed off the slide and section by immersion in water, after which destaining, if necessary, can be accomplished with a solution of 50 ml. water, 50 ml. 95% ethyl alcohol, 0.18 ml. sulfuric acid. The slides may or may not be placed next in a neutralizing solution of 50 ml. water, 50 ml. 95% ethyl alcohol, 0.5 g. sodium bicarbonate. They may then be passed through 50 ml. water, 50 ml. 95% ethyl alcohol on the way to alcoholic counterstaining solutions, or through water leading to aqueous counterstains.

The nuclear stain produced is black, intense and very sharp and has proved to be consistently excellent on a variety of animal and human tissues following a number of different fixatives.     

The Demonstration of Beryllium Oxide in Paraffin Sections with Chromoxane Stains

Aqueous solutions of the arylmethane dyes Chromoxane pure blue BLD (C.I. No. 43825) and Chromoxane pure blue B (C.I. No. 43830) will stain beryllium oxide. In the presence of EDTA the staining of other metals is masked. As a specific stain for BeO, formol saline fixed paraffin sections are hydrated and stained for 1 hr with either 0.1 gm of pure blue BLD in 100 ml of pH 4.0 Na-acetate buffer or with 0.1 gm of pure blue B in 1 N NaOH adjusted to pH 9.0 with HCl. To mask interference from other metal ions, 9 gm of Na₂-EDTA is added to 100 ml of the stain solution. BeO is stained blue, organic tissue components are either unstained or pink. Results of tests against other materials show that a high degree of specificity may be expected from these dyes. A 1% aqueous solution of neutral red may be used as a counterstain.     

Metallic Lakes of the oxazines (Gallamin Blue, Gallocyanin and Coelestin Blue) as Nuclear Stain Substitutes for Hematoxylin

Becher's investigations upon the soluble metallic lakes of the oxazines have been re-investigated, extended and results described. Gallamin blue, gallocyanin and coelestin blue in combination with ferric ammonium sulfate gave the best results. The dyes are dissolved in a five per cent aqueous solution of ferric ammonium sulfate. The solution is boiled for 2-3 minutes, cooled, filtered and ready for immediate use. The iron lakes of these dyes stain nuclei excellently giving a deep blue or blue black in 3-5 minutes. No differentiation with acid is required. Coelestin blue gives the most stable solution and is recommended as a routine nuclear stain. The protoplasm remains practically colorless and counter-staining with acid dyes such as ethyl-eosin, orange G, or fuchsin gives pictures which cannot be distinguished from a good hematoxylin stain.

Counter-staining with van Gieson solution is also possible. Benda's modification of the van Gieson solution is recommended. Staining of fat with Sudan, scarlet red, etc., does not interfere with nuclear staining by these dyes.

As applied to the central nervous system these dyes are far superior to hematoxylin. Ganglion and glia cells are as excellently stained as with thionin.

The most widely used fixatives, namely formaldehyde, Mueller-formaldehyde, Zenker's and alcohol, give equally as good results. The nature of the staining process is briefly discussed and a prospectus offered.