Disposable biosensor based on enzyme immobilized on Au-chitosan-modified indium tin oxide electrode with flow injection amperometric analysis

Indium tin oxide (ITO) electrode is used to fabricate a novel disposable biosensor combined with flow injection analysis for the rapid determination of H2O2. The biosensor is prepared by entrapping horseradish peroxidase (HRP) enzyme in colloidal gold nanoparticle-modified chitosan membrane (Au-chitosan) to modify the ITO electrode. The biosensor is characterized by scanning electron microscope, atomic force microscope, and electrochemical methods. Parameters affecting the performance of the biosensor, including concentrations of o-phenylenediamine (OPD) and pH of substrate solution, were optimized. Under the optimal experimental conditions, H2O2 could be determined in the linear calibration range from 0.01 to 0.5 mM with a correlation coefficient of 0.997 (n=8). The amperometric response of the biosensor did not show an obvious decrease after the substrates were injected continuously 34 times into the flow cell. The prepared biosensor not only is economic and disposable, due to the low-cost ITO film electrode obtained from industrial mass production, but also is capable with good detection precision, acceptable accuracy, and storage stability for the fabrication in batch.     

A biosensor for the analysis of acetonitrile

A biosensor for monitoring acetonitrile was constructed. A mixed culture was taken from a degradation reactor and mounted on top of a Clark electrode. The amperometric biosensor was placed in a flow-through cell and integrated into a flow injection system. The metabolic response in terms of oxygen consumption was well correlated to the concentration of acetonitrile in standard solutions. However, when the reaction products, acetic acid and ammonia, were also present, the response was erratic, due to the additional metabolic reaction on acetate. By introducing a hydrophobic barrier it was possible to eliminate the negative influence of these charged products and thus to improve the operational selectivity of the sensor.The biosensor showed good stability for analysis during at least 6 days and future work will focus on using it for monitoring and control of degradation processes.     

Lactose biosensor based on Langmuir-Blodgett films of poly(3-hexyl thiophene)

An amperometric lactose biosensor was developed by immobilizing lactase (EC 3.2.1.23) and galactose oxidase (GaO) (EC 1.1.3.9) in Langmuir-Blodgett (LB) films of poly(3-hexyl thiophene) (P3HT)/stearic acid (SA) for estimation of lactose in milk and its products to prevent "lactose intolerance". The enzyme immobilized LB film was used as working electrode and platinum as reference electrode. The enzyme electrodes show a linearity 1-6 g/dL of lactose and have a shelf life more than 120 days. The reusability of electrode was found ten times with 3% loss in current response. The enzyme electrode was characterized by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and kinetic parameters such as pH, temperature and stability. The working electrode may be used for the estimation of lactose/galactose in food and biological fluids.     

Sensitive amperometric biosensor for the determination of biogenic and synthetic amines using pea seedlings amine oxidase: a novel approach for enzyme immobilisation

We prepared a new inorganic sorbent based on modified triazine (2-[4,6-bis (aminoethylamine)-1,3,5-triazine]-Silasorb; BAT-Silasorb) which binds pea seedlings amine oxidase (PSAO) very tightly without loss of its catalytic activity. This unique feature as well as the wide substrate specificity of PSAO was successfully utilised in the construction of an amperometric biosensor based on a carbon paste electrode for the fast and sensitive detection of various amines at a formal potential 0 mV versus Ag/AgCl reference electrode. The reaction layer of the biosensor is created by the direct immobilisation of PSAO at the electrode surface via affinity carrier BAT-Silasorb. Used arrangement facilitates a simple restoration of the inactive biosensor. An amperometric signal results from horseradish peroxidase catalysed reduction of H2O2, a secondary product of the oxidative deamination of amines, catalysed by PSAO. The sensor was used for the basic characterisation of 55 biogenic and synthetic amines, from numerous mono-, di- and polyamines to various hydroxy-, thio-, benzyl- and aromatic derivatives in order to establish its suitability as a postcolumn detector. Its high sensitivity to putrescine 20.0 +/- 0.64 mA l-1 per mol (636.9 +/- 2.03 mA l-1 per mol per cm2), a limit of detection of 10 nmol l-1 (determined with respect to a signal-to-noise ratio 3:1), a linear range of current response to 0.01-100 mumol l-1 concentration of substrate and good reproducibility all indicate that the sensor could be applied to future industrial and clinical analyses.     

Optimization of a polypyrrole glucose oxidase biosensor

An amperometric glucose biosensor was fabricated by the electrochemical polymerization of pyrrole onto a platinum electrode in the presence of the enzyme glucose oxidase in a KCl solution at a potential of + 0·65 V versus SCE. The enzyme was entrapped into the polypyrrole film during the electropolymerization process. Glucose responses were measured by potentio-statting the enzyme electrode at a potential of + 0·7 V versus SCE in order to oxidize the hydrogen generated by the oxidation of glucose by the enzyme in the presence of oxygen. Experiments were performed to determined the optimal conditions of the polypyrrole glucose oxidase film preparation (pyrrole and glucose oxidase concentrations in the plating solution) and the response to glucose from such electrodes was evaluated as a function of film thickness, pH and temperature. It was found that a concentration of 0·3 M pyrrole in the presence of 65 U/ml of glucose oxidase in 0·01 M KCl were the optimal parameters for the fabrication of the biosensor. The optimal response was obtained for a film thickness of 0·17 μm (75 mC/cm²) at pH 6 and at a temperature of 313 K. The temperature dependence of the amperometric response indicated an activation energy of 41 kJ/mole. The linearity of the enzyme electrode response ranged from 1·0 mM to 7·5 mM glucose and kinetic parameters determined for the optimized biosensors were 33·4 mM for the K_m and 7·2 μA for the I_max. It was demonstrated that the internal diffusion of hydrogen peroxide through the polypyrrole layer to the platinum surface was the main limiting factor controlling the magnitude of the response of the biosensor to glucose. The response was directly related to the enzyme loading in the polypyrrole film. The shelf life and the operational stability of the optimized biosensor exceed 500 days and 175 assays, respectively. The substrate specificity of the entrapped glucose oxidase was not altered by the immobilization procedure.     

肌苷酶电极生物传感器

为了构建肌苷酶电极生物传感器,以固定化核苷磷酸化酶(EC 2.4.2.1)、黄嘌呤氧化酶(EC 1.2.3.2)与过氧化氢电极组成电流型酶电极生物传感器,用于检测肌苷片中的肌苷,其输出电流可达500nA.结果发现,肌苷测定的线性范围为1-268 mg/L,精度:RSD小于0.14%,响应时间:60 s,使用寿命大于25 d,实际测定肌苷片中肌苷含量回收率:100.8%.由此表明:采用双酶电极法测定肌苷片中的肌苷含量,由于酶促反应专一性高、样品不需分离直接进样分析、处理条件温和、反应时间短暂因而结果较为可靠.     

Determination of beta-D-glucose using flow injection analysis and composite-type amperometric tubular biosensors

An amperometric tubular cell involving composite biosensors for the determination of beta-d-glucose in a flow injection analysis (FIA) system is proposed. Diverse configurations and parameters are evaluated to improve the system's response. The configuration producing less noise resulted when the biosensor was located closer to the auxiliary electrode, which also required coupling both electrodes within the system under a continuous flow regime. Further, we report on the influence of the active area of the biosensor and of the flow rate used. Statistical analyses of the data revealed two regions with a linear response range for the determination of beta-d-glucose, with a detection limit of 4.7 x 10(-4) M and in the low concentration region a sensitivity of 17.46 +/- 0.12 microAM(-1). At the beta-d-glucose concentrations studied there was no evidence of enzymatic saturation. An increment on the ionic strength of the sample and carrier passing through the analysis system decreases its sensitivity. The reproducibility of the analytical system in terms of its standard deviation was 2.9% with a 95% confidence level, having a lifetime that lasted at least 100 days. beta-d-Glucose was determined in different commercial medical glucose-containing solutions, the experimental results are in good agreement with those reported by the manufacturer.     

Chiral analysis of amino acids using electrochemical composite bienzyme biosensors.

The construction and performance of bienzyme amperometric composite biosensors for the selective determination of l- or d-amino acids is reported. D- or L-Amino acid oxidase, horseradish peroxidase, and the mediator ferrocene were coimmobilized by simple physical inclusion into the bulk of a graphite-70% Teflon electrode matrix. Working conditions including amino acid oxidase loading and pH were optimized. Studies on the repeatability of the amperometric response obtained at +0.00 V, with and without regeneration of the electrode surface by polishing, on the useful lifetime of one single biosensor and on the reproducibility in the fabrication of different biosensors illustrate the robustness of the bioelectrodes design. Calibration plots by both amperometry in stirred solutions and flow injection with amperometric detection were obtained for L-arginine, L-phenylalanine, L-leucine, L-methionine, L-tryptophan, D-leucine, D-methionine, D-serine, and D-valine. Differences in sensitivity were discussed in terms of the hydrophobicity of the substrate and of the electrode surface. The bienzyme composite electrode was applied to the determination of L- and D-amino acids in racemic samples, as well as to the estimation of the L-amino acids content in muscatel grapes.     

An FIA biosensor system for the determination of phosphate.

A flow injection analysis (FIA) biosensor system for the determination of phosphate was constructed using immobilized nucleoside phosphorylase and xanthine oxidase and an amperometric electrode (platinum vs silver/silver chloride, polarized at 0.7 V). When a phosphate-containing sample was injected into the detection cell, phosphate reacted with inosine in the carrier buffer to produce hypoxanthine and ribose-1-phosphate in the presence of nucleoside phosphorylase. Hypoxanthine was then oxidized by xanthine oxidase to uric acid and hydrogen peroxide, which were both detected by the amperometric electrode. The response of the FIA biosensor system was linear up to 100 microM phosphate, with a minimum detectable concentration of 1.25 microM phosphate. Each assay could be performed in 5-6 min and the system could be used for about 160 repeated analyses. This system was applicable for the determination of phosphate in various food products and plasma, and the results obtained agreed well with those of the enzymatic assay.     

Amperometric microbial biosensor for p-nitrophenol using Moraxella sp.-modified carbon paste electrode

An amperometric microbial biosensor for highly specific, sensitive and rapid quantitative determination of p-nitrophenol was developed. The biosensor takes advantage of the ability of Moraxella sp. to specifically degrade p-nitrophenol to hydroquinone, a more electroactive compound than p-nitrophenol. The electrochemical oxidation current of hydroquinone formed in biodegradation of p-nitrophenol was measured at Moraxella sp.-modified carbon paste electrode and correlated to p-phenol concentrations. The optimum response was realized by electrode constructed using 15 mg of dry cell weight per 1 g of carbon paste and operating at 0.3 V (versus Ag/AgCl reference) in pH 7.5, 20 mM sodium phosphate buffer. Operating at these optimum conditions the biosensor had excellent selectivity against phenol derivatives and was able to measure as low as 20 nM (2.78 ppb) p-nitrophenol with very good accuracy and reproducibility. The biosensor was stable for approximately 3 weeks when stored at 4 degrees C. The applicability of the biosensor to measure p-nitrophenol in lake water was demonstrated.     

Silica sol-gel composite film as an encapsulation matrix for the construction of an amperometric tyrosinase-based biosensor

An amperometric tyrosinase enzyme electrode for the determination of phenols was developed by a simple and effective immobilization method using sol-gel techniques. A grafting copolymer was introduced into sol-gel solution and the composition of the resultant organic-inorganic composite material was optimized, the tyrosinase retained its activity in the sol-gel thin film and its response to several phenol compounds was determined at 0 mV vs. Ag/AgCl (sat. KCl). The dependences of the current response on pH, oxygen level and temperature were studied, and the stability of the biosensor was also evaluated. The sensitivity of the biosensor for catechol, phenol and p-cresol was 59.6, 23.1 and 39.4 microA/mM, respectively. The enzyme electrode maintained 73% of its original activity after intermittent use for three weeks when storing in a dry state at 4 degrees C.     

Glucose biosensor based on multi-wall carbon nanotubes and screen printed carbon electrodes

This paper describes a disposable electrochemical biosensor for glucose monitoring. The sensor was based on multi-wall carbon nanotubes (MWCNTs) immobilized with glucose oxidase and upon screen printed carbon electrode. The effect of MWCNTs on the response of amperometric glucose oxidase electrode for glucose was examined. Results obtained, of interest for basic and applied biochemistry, represent a first step in construction of a MWCNT-enzyme electrode biosensor with potentialities for a successful application in the biosensor area.     

Detection of p53 gene point mutation using sequence-specific molecularly imprinted PoPD electrode

An amperometric sequence-specific molecularly imprinted single-stranded oligodeoxyribonucleotide (ss-ODN) biosensor was fabricated and characterised in this study. Using ss-ODN as the template and o-phenylenediamine as the functional monomer, the ODN biosensor was fabricated by an electropolymerisation process on an indium-tin oxide (ITO) coated glass substrate. The template ss-ODN was washed out of the ss-ODN/poly(o-phenylenediamine)(PoPD)/ITO electrode using sterilised basic ethanol-water. The resulting ss-ODN imprinted PoPD/ITO electrode was characterised using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and cyclic voltammetry (CV). The amperometric responses, i.e., Δi as a function of the target ss-ODN concentration was studied. The biosensor using ss-ODN imprinted PoPD/ITO as the working electrode showed a linear Δ current response to the target ss-ODN concentration within the range of 0.01-300 fM. The biosensor showed a sensitivity of 0.62 μA/fM, with a response time of 14s. The present novel molecularly imprinted ss-ODN biosensor could greatly benefit in terms of cost-effectiveness, storage stability, ultra sensitivity and selectivity together with the potential for improved commercial genetic sensors.     

An amperometric lactate biosensor based on lactate dehydrogenase immobilized onto graphene oxide nanoparticles‐modified pencil graphite electrode

A novel amperometric lactate biosensor was developed based on immobilization of lactate dehydrogenase onto graphene oxide nanoparticles‐decorated pencil graphite electrode. The enzyme electrode was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), and cyclic voltammetry at different stages of its construction. The biosensor showed optimum response within 5 s at pH 7.3 (0.1 M sodium phosphate buffer) and 35°C, when operated at 0.7 V. The biosensor exhibited excellent sensitivity (detection limit as low as 0.1 μM), fast response time (5 s), and wider linear range (5–50 mM). Analytical recovery of added lactic acid in serum was between 95.81–97.87% and within‐batch and between‐batch coefficients of variation were 5.04 and 5.40%, respectively. There was a good correlation between serum lactate values obtained by standard colorimetric method and the present biosensor (r = 0.99). The biosensor measured lactate levels in sera of apparently healthy subjects and persons suffering from lactate acidosis and other biological materials (milk, curd, yogurt, beer, white wine, and red wine). The enzyme electrode lost 25% of its initial activity after 60 days of its regular uses, when stored dry at 4°C.     

Amperometric glucose biosensor based on lipid film

A novel glucose biosensor based on cast lipid film was developed. This model of biological membrane was used to supply a biological environment on the surface of the electrode, moreover it could greatly reduce the interference and effectively exclude hydrophilic electroactive material from reaching the detecting surface. TTF was selected as a mediator because of its high electron-transfer efficiency, and it was incorporated in the lipid film firmly. Glucose oxidase was immobilized in hydrogel covered on the lipid film. The effects of pH, operating potential were explored for the optimum analytical performance by using amperometric method. The response time of the biosensor was less than 20 s, and the linear range is up to 10 mmol l(-1) (corr. coeff. 0.9932) with the detection limit of 2 x 10(-5) mol l(-1). The biosensor also exihibited good stability and reproducibility.     

A novel glucose sensor based on monodispersed Ni/Al layered double hydroxide and chitosan

A novel cheap and simple amperometric glucose biosensor, based on the electrode modified with the Ni/Al layered double hydroxide (LDH) nanoflakes and chitosan (CHT), without glucose oxidase, is presented. The glucose biosensor based on monodispersed high active Ni/Al-LDH nanoflakes and CHT exhibits an appropriate linear range of 0.01-10mM and good operational stability. The amperometric sensor shows a rapid response at the potential value 0.48V. In addition, optimization of the biosensor construction, the effects of the applied potential, the scan rate as well as common interfering compounds on the amperometric response and human serum samples analysis of the sensor were investigated and discussed.     

A high sensitivity amperometric biosensor using laccase as biorecognition element

An amperometric flow biosensor, using laccase from Rigidoporus lignosus as bioelement was developed. The laccase was kinetically characterized towards various phenolics both in solution and immobilized to a hydrophilic matrix by carbodiimide chemistry. A bioreactor connected to an amperometric flow cell by a FIA system was filled with the immobilized enzyme and the operational conditions of this biosensor were optimized as regards pH. Under the adopted experimental conditions, the immobilized enzyme oxidizes all the substrate molecules avoiding the need of cumbersome calibration procedures. The biosensor sensitivity, which was found to be 100 nA/microM for some of the tested substrates, resulted to be constant for more than 100 working days. This biosensor permits the detection of phenolics in aqueous solutions at concentrations in the nanomolar range and was successfully used to detect phenolics in wastewaters from olive oil mill without sample preparation.     

Detection of β-glucans using an amperometric biosensor based on high-affinity interaction between Dectin-1 and β-glucans

Early diagnosis of fungal infection plays an important role in increasing antifungal therapeutic response, but meaningful tests such as microbiological cultures and histopathological diagnosis are usually insensitive and time-consuming. A sensitive amperometric biosensor for β-glucans was fabricated by immobilizing Dectin-1 onto Nafion-thionine-gold nanoparticle-chitosan multilayer films to trap its corresponding ligand from sample solution. On formation of ligand-receptor complex, detection of β-glucans was accomplished by monitoring the decrease of the electrochemical signal of the modified electrode due to the inhibition of the transmission of electrons. Dectin-1 was constructed by cloning the extracellular carbohydrate recognition domain of the mouse Dectin gene into the pET28a(+) prokaryotic expression vector. Optimal conditions and analytical performances of the described biosensor were investigated. Under the optimal conditions, the biosensor response for β-glucans presented good accuracy, stability, and reproducibility. The proposed biosensor not only could be used for rapid analysis of serum β-glucans but also provided a screening procedure for the determination of fungal infections.     

Amperometric and impedimetric characterization of a glutamate biosensor based on Nafion and a methyl viologen modified glassy carbon electrode

An electrochemical biosensor based on a glassy carbon (GC) electrode chemically modified with the perfluorinated cation-exchange polymer Nafion and methyl viologen (MV) is described. The enzyme was immobilized by cross-linking with glutaraldehyde in the presence of bovine serum albumin (BSA), methyl viologen and Nafion. Operating variables such as the enzyme/BSA ratio, cross-linking time in glutaraldehyde vapor, methyl viologen and Nafion percentages were investigated with regard to their influence on the biosensor sensitivity by using glucose oxidase as the enzyme model due to its high stability and low cost. The glutamate biosensor was elaborated by using optimized parameters and its electrochemical properties were investigated by cyclic voltammetry, amperometry and by electrochemical impedance spectroscopy. The glutamate biosensor shows a detection limit of 20 microM and a linear range extended to 0.75 mM. Its selectivity was tested with 15 different amino acids, each with a concentration of 20 microM, 25 microM acetaminophen, 20 microM uric acid and 200 microM ascorbic acid. No amperometric response was observed for the interfering species. This good selectivity allows glutamate detection in biological media without previous separation of the analyte.     

An amperometric pyruvate biosensor based on pyruvate oxidase nanoparticles immobilized onto pencil graphite electrode

This present study was aimed to fabricate a sensitive and improved amperometric biosensor by the nanoparticles of pyruvate oxidase, which were prepared and immobilized covalently onto pencil graphite electrode. The biosensor showed ideal working within 5 s under defined conditions of pH 6.0 and incubation temperature of 30 °C at an applied voltage of -0.1 V. Under standard assay conditions, a linear response was obtained between pyruvate concentration ranging from 0.001 to 6000 μM and current (μA). A lower detection limit (0.58 μM) and an excellent correlation coefficient (R² = 0.999) with standard spectrophotometric assay was obtained for the present biosensor. Within and between batches of coefficients of variation were calculated and found to be 3.61 % and 3.33 %, respectively. The biosensor was put to continual use for over 210 days. The biosensor was employed for the measurement of pyruvate level in sera of normal healthy individuals and persons suffering from heart disease.