The cellulose/lignin assembly assessed by molecular modeling. Part 1: adsorption of a threo guaiacyl beta-O-4 dimer onto a Ibeta cellulose whisker.

The assembly of the two major cell wall components, cellulose and lignin, were investigated at the atomistic scale using molecular dynamics simulations. To this end, a molecular model of a cellulose crystal corresponding to the allomorph Ibeta and exhibiting different surfaces was considered to mimic the carbohydrate matrix present in native wood cell wall. The lignin model compound considered here is a threo guaiacyl beta-O-4 dimer. The dynamical process of adsorption of the lignin dimer onto the different surfaces of the cellulose crystal was examined. The modes of association between the two constituents were analyzed; energies of adsorption of the dimer are calculated favorable and of the same order of magnitude on all sides of the cellulosic model, suggesting that the deposition of lignin precursors onto cellulose fibers is non-specific from an enthalpic point of view. Interestingly, geometrical characteristics and energetical details of the adsorption are surface-dependent. Computed data have underlined the predominant contribution of van der Waals interactions for adsorption onto the (200) face, as well as the major influence of H-bonding interactions in the dynamical process of adsorption onto (110) and (1-10) faces. A large number of adsorption sites have been identified and a noticeable "flat" geometry of adsorption of the lignin dimer has been observed, as a consequence of the stacking interactions between lignin aromatic rings and C-H groups of cellulose. Importantly, these dispersive interactions lead to a preferential parallel orientation of lignin aromatic rings relative to the cellulose surface, notably on the (200) face. Such a parallel orientation is consistent with previously reported experimental observations.     

Characterization of carbons derived from cellulose and lignin and their oxidative behavior

In this study the oxidative behavior of carbons derived from cellulose and lignin were compared using thermogravimetric analysis (TGA). Specific surface area and chemical composition of the two types of carbon were analyzed using nitrogen adsorption at 77 K and infrared spectroscopy respectively. The results demonstrate that cellulose carbon has a higher reaction order and lower activation energy than lignin carbon under identical experimental conditions when they were prepared at temperatures lower than 500 °C. However, such differences were considerably reduced for the carbon samples prepared at temperatures greater than 700 °C. It was verified that lignin carbon is more stable than cellulose carbon due to its higher content of aromatic structures when they are prepared at lower temperature. The specific surface area and porosity have a more limited contribution to the differential oxidative behaviors of the two types of carbon. This research has significance related to the formation of carbon nanotubes from plant materials during low temperature carbonization.     

Repression of lignin biosynthesis promotes cellulose accumulation and growth in transgenic trees.

Because lignin limits the use of wood for fiber, chemical, and energy production, strategies for its downregulation are of considerable interest. We have produced transgenic aspen (Populus tremuloides Michx.) trees in which expression of a lignin biosynthetic pathway gene Pt4CL1 encoding 4-coumarate:coenzyme A ligase (4CL) has been downregulated by antisense inhibition. Trees with suppressed Pt4CL1 expression exhibited up to a 45% reduction of lignin, but this was compensated for by a 15% increase in cellulose. As a result, the total lignin-cellulose mass remained essentially unchanged. Leaf, root, and stem growth were substantially enhanced, and structural integrity was maintained both at the cellular and whole-plant levels in the transgenic lines. Our results indicate that lignin and cellulose deposition could be regulated in a compensatory fashion, which may contribute to metabolic flexibility and a growth advantage to sustain the long-term structural integrity of woody perennials.     

BSA treatment to enhance enzymatic hydrolysis of cellulose in lignin containing substrates

Cellulase and bovine serum albumin (BSA) were added to Avicel cellulose and solids containing 56% cellulose and 28% lignin from dilute sulfuric acid pretreatment of corn stover. Little BSA was adsorbed on Avicel cellulose, while pretreated corn stover solids adsorbed considerable amounts of this protein. On the other hand, cellulase was highly adsorbed on both substrates. Adding a 1% concentration of BSA to dilute acid pretreated corn stover prior to enzyme addition at 15 FPU/g cellulose enhanced filter paper activity in solution by about a factor of 2 and beta-glucosidase activity in solution by about a factor of 14. Overall, these results suggested that BSA treatment reduced adsorption of cellulase and particularly beta-glucosidase on lignin. Of particular note, BSA treatment of pretreated corn stover solids prior to enzymatic hydrolysis increased 72 h glucose yields from about 82% to about 92% at a cellulase loading of 15 FPU/g cellulose or achieved about the same yield at a loading of 7.5 FPU/g cellulose. Similar improvements were also observed for enzymatic hydrolysis of ammonia fiber explosion (AFEX) pretreated corn stover and Douglas fir treated by SO(2) steam explosion and for simultaneous saccharification and fermentation (SSF) of BSA pretreated corn stover. In addition, BSA treatment prior to hydrolysis reduced the need for beta-glucosidase supplementation of SSF. The results are consistent with non-specific competitive, irreversible adsorption of BSA on lignin and identify promising strategies to reduce enzyme requirements for cellulose hydrolysis.     

The use of natural abundance stable isotopic ratios to indicate the presence of oxygen-containing chemical linkages between cellulose and lignin in plant cell walls

Qualitative and quantitative understanding of the chemical linkages between the three major biochemical components (cellulose, hemicellulose and lignin) of plant cell walls is crucial to the understanding of cell wall structure. Although there is convincing evidence for chemical bonds between hemicellulose and lignin and the absence of chemical bonds between hemicellulose and cellulose, there is no conclusive evidence for the presence of covalent bonds between cellulose and lignin. This is caused by the lack of selectivity of current GC/MS-, NMR- and IR-based methods for lignin characterisation as none of these techniques directly targets the possible ester and ether linkages between lignin and cellulose. We modified the widely-accepted “standard” three-step extraction method for isolating cellulose from plants by changing the order of the steps for hemicellulose and lignin removal (solubilisation with concentrated NaOH and oxidation with acetic acid-containing NaClO₂, respectively) so that cellulose and lignin could be isolated with the possible chemical bonds between them intact. These linkages were then cleaved with NaClO₂ reagent in aqueous media of contrasting ¹⁸O/¹⁶O ratios. We produced cellulose with higher purity (a lower level of residual hemicellulose and no detectable lignin) than that produced by the “standard” method. Oxidative artefacts may potentially be introduced at the lignin removal stage; but testing showed this to be minimal.Cellulose samples isolated from processing plant-derived cellulose–lignin mixtures in media of contrasting ¹⁸O/¹⁶O ratios were compared to provide the first quantitative evidence for the presence of oxygen-containing ester and ether bonds between cellulose and lignin in Zea mays leaves. However, no conclusive evidence for the presence or lack of similar bonds in Araucaria cunninghamii wood was obtained.     

Biodegradation of high molecular weight lignin under sulfate reducing conditions: lignin degradability and degradation by-products

This study is designed to investigate the biodegradation of high molecular weight (HMW) lignin under sulfate reducing conditions. With a continuously mesophilic operated reactor in the presence of co-substrates of cellulose, the changes in HMW lignin concentration and chemical structure were analyzed. The acid precipitable polymeric lignin (APPL) and lignin monomers, which are known as degradation by-products, were isolated and detected. The results showed that HMW lignin decreased and showed a maximum degradation capacity of 3.49 mg/l/day. APPL was confirmed as a polymeric degradation by-product and was accumulated in accordance with HMW lignin reduction. We also observed non-linear accumulation of aromatic lignin monomers such as hydrocinnamic acid. Through our experimental results, it was determined that HMW lignin, when provided with a co-substrate of cellulose, is biodegraded through production of APPL and aromatic monomers under anaerobic sulfate reducing conditions with a co-substrate of cellulose.     

模拟氮沉降对华西雨屏区天然常绿阔叶林凋落物木质素和纤维素降解的影响

从2013年11月至2014年11月,采用尼龙网袋法对华西雨屏区天然常绿阔叶林凋落物进行原位分解试验,模拟N(NH₄NO₃)沉降水平分别为对照(0 g N·m^-2·a^-1)、低氮沉降(5 g N·m^-2·a^-1)、中氮沉降(15 g N·m^-2·a^-1)和高氮沉降(30 g N·m^-2·a^-1),研究了N沉降对常绿阔叶林凋落物分解及其木质素和纤维素降解的影响.结果表明:华西雨屏区天然常绿阔叶林凋落物在夏季分解较快,明显快于其他季节.N沉降显著抑制了阔叶林凋落物的分解,抑制作用随N沉降量的增加而加强.N沉降使凋落物质量损失95%的时间与对照(4.81年)相比增加了0.53～1.88年.经过1 年的分解,中氮沉降和高氮沉降处理木质素和纤维素残留率显著高于对照,表明N沉降显著抑制了凋落物木质素和纤维素的降解.凋落物质量残留率与木质素和纤维素残留率呈显著正相关.N沉降抑制凋落物分解的原因可能是无机N的添加对木质素和纤维素的降解造成了阻碍.     

Cellulose-Lignin Interactions (A Computational Study)

Within a broader program of study of the molecular structure of plant cell walls, molecular dynamics calculations were used to explore the character of the motion of lignin model compounds near a cellulose surface. Model cellulose microfibrils, which have a large number of hydroxyl groups on the surface, appear to have a net attractive interaction with the lignin models examined in this study. The lignin monomer coniferyl alcohol rapidly adsorbed onto the surface from a water layer after it was released 13 A from the surface. The major long-range force responsible for this adsorption is likely electrostatic. The attractive interaction is sufficient to restrict the motion of coniferyl alcohol when it is within 1 A of the surface and to orient the phenyl ring parallel to the surface. The [beta]-O-4-linked trimer also was observed to adsorb onto the surface with two of its phenyl rings parallel to the surface. These results suggest a mechanism by which the polysaccharide component of the plant cell wall could influence the structure of lignin. Furthermore, they provide a rationalization of the experimental observation that polysaccharides can change the course of dehydrogenation polymerization of cinnamyl alcohols.     

Reconstitution of cellulose and lignin after [C2mim][OAc] pretreatment and its relation to enzymatic hydrolysis

Although the effects of cellulose crystallinity and lignin content as two major structural features on enzymatic hydrolysis have been extensively studied, debates regarding their effects still exist. In this study, reconstitution of cellulose and lignin after 1‐ethyl‐3‐methylimidazolium acetate ([C₂mim][OAc]) pretreatment was proposed as a new method to study their effects on enzymatic digestibility. Different mechanisms of lignin content for reduction of cellulose hydrolysis were found between the proposed method and the traditional method (mixing of cellulose and lignin). The results indicated that a slight change of the crystallinity of the reconstituted materials may play a minor role in the change of enzyme efficiency. In addition, the present study suggested that the lignin content does not significantly affect the digestibility of cellulose, whereas the conversion of cellulose fibers from the cellulose I to the cellulose II crystal phase plays an important role when an ionic liquid pretreatment of biomass was conducted. Biotechnol. Bioeng. 2013; 110: 729–736. © 2012 Wiley Periodicals, Inc.     

Deposition of lignin droplets produced during dilute acid pretreatment of maize stems retards enzymatic hydrolysis of cellulose

Electron microscopy of lignocellulosic biomass following high-temperature pretreatment revealed the presence of spherical formations on the surface of the residual biomass. The hypothesis that these droplet formations are composed of lignins and possible lignin carbohydrate complexes is being explored. Experiments were conducted to better understand the formation of these "lignin" droplets and the possible implications they might have on the enzymatic saccharification of pretreated biomass. It was demonstrated that these droplets are produced from corn stover during pretreatment under neutral and acidic pH at and above 130 degrees C, and that they can deposit back onto the surface of residual biomass. The deposition of droplets produced under certain pretreatment conditions (acidic pH; T > 150 degrees C) and captured onto pure cellulose was shown to have a negative effect (5-20%) on the enzymatic saccharification of this substrate. It was noted that droplet density (per unit area) was greater and droplet size more variable under conditions where the greatest impact on enzymatic cellulose conversion was observed. These results indicate that this phenomenon has the potential to adversely affect the efficiency of enzymatic conversion in a lignocellulosic biorefinery.     

Carbohydrate derived‐pseudo‐lignin can retard cellulose biological conversion

Dilute acid as well as water only (hydrothermal) pretreatments often lead to a significant hemicellulose loss to soluble furans and insoluble degradation products, collectively termed as chars and/or pseudo‐lignin. In order to understand the factors contributing to reducing sugar yields from pretreated biomass and the possible influence of hemicellulose derived pseudo‐lignin on cellulose conversion at the moderate to low enzyme loadings necessary for favorable economics, dilute acid pretreatment of Avicel cellulose alone and mixed with beechwood xylan or xylose was performed at various severities. Following pretreatment, the solids were enzymatically hydrolyzed and characterized for chemical composition and physical properties by NMR, FT‐IR, and SEM imaging. It was found that hemicelluloses (xylan) derived‐pseudo‐lignin was formed at even moderate severities and that these insoluble degradation products can significantly retard cellulose hydrolysis. Furthermore, although low severity (CSF ～ 1.94) dilute acid pretreatment of a xylan–Avicel mixture hydrolyzed most of the xylan (98%) and produced negligible amounts of pseudo‐lignin, enzymatic conversion of cellulose dropped significantly (>25%) compared to cellulose pretreated alone at the same conditions. The drop in cellulose conversion was higher than realized for cellulase inhibition by xylooligomers reported previously. Plausible mechanisms are discussed to explain the observed reductions in cellulose conversions. Biotechnol. Bioeng. 2013; 110: 737–753. © 2012 Wiley Periodicals, Inc.     

The adsorption of xyloglucan on cellulose: effects of explicit water and side chain variation

The interaction between para-crystalline cellulose and the cross-linking glycan xyloglucan (XG) plays a central role for the strength and extensibility of plant cell walls. The coating of XGs on cellulose surfaces is believed to be one of the most probable interaction patterns. In this work, the effects of explicit water and side chain variation on the adsorption of XGs on cellulose are investigated by means of atomistic molecular dynamics simulations. The adsorption properties are studied in detail for three XGs on cellulose Iβ 1–10 surface in aqueous environment, namely GXXXGXXXG, GXXLGXXXG, and GXXFGXXXG, which differ in the length and composition of one side chain. Our work shows that when water molecules are included in the theoretical model, the total interaction energies between the adsorbed XGs and cellulose are considerably smaller than in vacuo. Furthermore, in water environment the van der Waals interactions prevail over the electrostatic interactions in the adsorption. Variation in one side chain does not have significant influence on the interaction energy and the binding affinity, but does affect the equilibrium structural properties of the adsorbed XGs to facilitate the interaction between both the backbone and the side chain residues with the cellulose surface. Together, this analysis provides new insights into the nature of the XG–cellulose interaction, which helps to further refine current molecular models of the composite plant cell wall.     

Degradation of polysaccharides and lignin in wood ozonation

Ozonation has been considered as a method for the pretreatment of plant biomass to obtain cellulose and monosaccharides. Ozone consumption by aspen wood with various moisture contents has been investigated. We have considered the gradual transformation of the substrate: wood to ozonated wood to cellulose-containing product (CP) to holocelluloze (HC) and to cellulose. Yields of ozonated wood (OW), the (CP), water-soluble ozonation products, HC, and cellulose have been determined. The lignin content in the CP has been estimated. Both HC and cellulose samples have been studied by IR spectroscopy. The degree of polymerization and molecular mass distribution of cellulose obtained from ozonated wood have been determined. It has been shown that wood destruction by ozone is accompanied by degradation of lignin, hemicelluloses, and cellulose.It has been found that physicochemical properties of cellulose obtained from ozonated wood can be regulated by the variation of the initial moisture content in the substrate. Both molecular ozone and radical species, which are generated in the course of ozone reactions with water present in the substrate structure, participate in wood destruction.     

Access of cellulase to cellulose and lignin for poplar solids produced by leading pretreatment technologies

Adsorption of cellulase on solids resulting from pretreatment of poplar wood by ammonia fiber expansion (AFEX), ammonia recycled percolation (ARP), controlled pH, dilute acid (DA), flowthrough (FT), lime, and sulfur dioxide (SO₂) and pure Avicel glucan was measured at 4°C, as were adsorption and desorption of cellulase and adsorption of β‐glucosidase for lignin left after enzymatic digestion of the solids from these pretreatments. From this, Langmuir adsorption parameters, cellulose accessibility to cellulase, and the effectiveness of cellulase adsorbed on poplar solids were estimated, and the effect of delignification on cellulase effectiveness was determined. Furthermore, Avicel hydrolysis inhibition by enzymatic and acid lignin of poplar solids was studied. Flowthrough pretreated solids showed the highest maximum cellulase adsorption capacity (σ_solids = 195 mg/g solid) followed by dilute acid (σ_solids = 170.0 mg/g solid) and lime pretreated solids (σ_solids = 150.8 mg/g solid), whereas controlled pH pretreated solids had the lowest (σ_solids = 56 mg/g solid). Lime pretreated solids also had the highest cellulose accessibility (σ_cellulose = 241 mg/g cellulose) followed by FT and DA. AFEX lignin had the lowest cellulase adsorption capacity (σ_lignin = 57 mg/g lignin) followed by dilute acid lignin (σ_lignin = 74 mg/g lignin). AFEX lignin also had the lowest β‐glucosidase capacity (σ_lignin = 66.6 mg/g lignin), while lignin from SO₂ (σ_lignin = 320 mg/g lignin) followed by dilute acid had the highest (301 mg/g lignin). Furthermore, SO₂ followed by dilute acid pretreated solids gave the highest cellulase effectiveness, but delignification enhanced cellulase effectiveness more for high pH than low pH pretreatments, suggesting that lignin impedes access of enzymes to xylan more than to glucan, which in turn affects glucan accessibility. In addition, lignin from enzymatic digestion of AFEX and dilute acid pretreated solids inhibited Avicel hydrolysis less than ARP and flowthrough lignin, whereas acid lignin from unpretreated poplar inhibited enzymes the most. Irreversible binding of cellulase to lignin varied with pretreatment type and desorption method. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Adsorption of a strong polyelectrolyte to model lignin surfaces

The adsorption of a strong, highly charged cationic polyelectrolyte to a kraft lignin thin film was investigated as a function of the adsorbing solution conditions using the quartz crystal microbalance. The polyelectrolyte, PDADMAC, with a molecular weight of 100 kDa and one cationic charge group per monomer, was adsorbed to the anionically charged lignin film in the pH range 3.5-9.5 in electrolyte solution of 0.1 to 100 mM NaCl. At low pH, the adsorbed amount of PDADMAC was minimal, however, this increased as a function of increasing pH. Indeed, the surface excess increased significantly at about pH 8.5, where ionization of the phenolic groups on the lignin macromolecule may be expected. Furthermore, at this elevated pH, the adsorbed amount of PDADMAC decreased as the ionic strength of the solution increased above 1 mM. This is due to the competitive adsorption of counterions to the lignin surface and indicates that the adsorption of PDADMAC to lignin is of a pure electrosorption nature.     

Covalent linkages between cellulose and lignin in cell walls of coniferous and nonconiferous woods

Covalent linkages between wall polysaccharides and lignin, especially linkage between cellulose and lignin were discussed by carboxymethylation technique of whole cell walls of coniferous and nonconiferous woods. Hydroxyl groups of plant cell walls polysaccharides were highly substituted, but not those of lignin by carboxymethyl groups under the used conditions, and separated into water-soluble and insoluble fractions by water extraction. Carboxymethylated wall polysaccharides linked covalently with lignin were distributed into the water-insoluble fractions. Composition of carboxymethylated sugar residues in the both fractions was analyzed quantitatively by 1H NMR spectroscopy after hydrolyzation with D2SO4 in D2O. More than half of cellulose linked covalently with lignin in coniferous wood, but only one-sixth of cellulose was involved in the linkage in nonconiferous wood. The major noncellulosic wall polysaccharides of coniferous wood also linked significantly with lignin. On the other hand, noncellulosic wall polysaccharides of nonconiferous wood were involved slightly in the covalent linkage with lignin. The situation of linkage between wall polysaccharides containing cellulose and lignin was visualized by scanning electron micrographs.     

Increasing cellulose accessibility is more important than removing lignin: A comparison of cellulose solvent‐based lignocellulose fractionation and soaking in aqueous ammonia

While many pretreatments attempt to improve the enzymatic digestibility of biomass by removing lignin, this study shows that improving the surface area accessible to cellulase is a more important factor for achieving a high sugar yield. Here we compared the pretreatment of switchgrass by two methods, cellulose solvent‐ and organic solvent‐based lignocellulose fractionation (COSLIF) and soaking in aqueous ammonia (SAA). Following pretreatment, enzymatic hydrolysis was conducted at two cellulase loadings, 15 filter paper units (FPU)/g glucan and 3 FPU/g glucan, with and without BSA blocking of lignin absorption sites. The hydrolysis results showed that the lignin remaining after SAA had a significant negative effect on cellulase performance, despite the high level of delignification achieved with this pretreatment. No negative effect due to lignin was detected for COSLIF‐treated substrate. SEM micrographs, XRD crystallinity measurements, and cellulose accessibility to cellulase (CAC) determinations confirmed that COSLIF fully disrupted the cell wall structure, resulting in a 16‐fold increase in CAC, while SAA caused a 1.4‐fold CAC increase. A surface plot relating the lignin removal, CAC, and digestibility of numerous samples (both pure cellulosic substrates and lignocellulosic materials pretreated by several methods) was also developed to better understand the relative impacts of delignification and CAC on glucan digestibility. Biotechnol. Bioeng. 2011; 108:22–30. © 2010 Wiley Periodicals, Inc.     

Impact of lignins isolated from pretreated lignocelluloses on enzymatic cellulose saccharification

Lignins were enzymatically isolated from corn stover and wheat straw samples and subjected to hydrothermal or wet oxidation pretreatments for enzyme adsorption experimentations. Lignin contents of the isolates ranged from 26 to 71 % (w/w); cellulose ranged from 3 to 22 % (w/w); xylan from 0.7 to 6 % (w/w) and ash was from 5.8 to 30 % (w/w). ATR-IR analyses indicated significant and similar levels of calcium in all lignin isolates. Commercial cellulase adsorption studies showed that the presence of these lignins had no significant impact on the total amount of adsorbed enzyme in cellulose and cellulose–lignin systems. Consequently, the presence of the lignins had minimal effect, if any, on enzymatic cellulose conversion. Furthermore, this result, coupled with significant calcium levels in the isolated lignins, supports previous work suggesting lignin–calcium complexes reduce enzyme–lignin interactions.     

Sorption of penicillium-cellulase on cellulose and lignin

Sorption of Penicillium cellulase onto cotton linters samples differing in physical structure and onto KLASON - lignin from spruce has been investigated by determining cellobiase, CMCL- and ‘linters-activity’ as well as protein content of a cellulase culture filtrate before and after contact with the sorbent at different temperature for different time intervals. CMCL- and cellobiase-activity were found to be reduced much less by the sorption process onto the cellulose samples than ‘linters-activity’ and protein content. Sorption increased in the order: untreated linters < mercerized linters < wet fibrillated (‘colloidal milled’) linters. With the KLASON -lignin also a considerable sorption of the cellulase system was observed. Results are discussed with respect to preferential sorption of enzyme components.     

The lignin present in steam pretreated softwood binds enzymes and limits cellulose accessibility

The influence of cellulose accessibility and protein loading on the efficiency of enzymatic hydrolysis of steam pretreated Douglas-fir was assessed. It was apparent that the lignin component significantly influences the swelling/accessibility of cellulose as at low protein loadings (5 FPU/g cellulose), only 16% of the cellulose present in the steam pretreated softwood was hydrolyzed while almost complete hydrolysis was achieved with the delignified substrate. When lignin (isolated from steam pretreated Douglas-fir) was added back in the same proportions it was originally found to the highly accessible and swollen, delignified steam pretreated softwood and to a cellulose control such as Avicel, the hydrolysis yields decreased by 9 and 46%, respectively. However, when higher enzyme loadings were employed, the greater availability of the enzyme could overcome the limitations imposed by both the lignin’s restrictions on cellulose accessibility and direct binding of the enzymes, resulting in a near complete hydrolysis of the cellulose.