Kinetics, mechanism, and time course analysis of lipase-catalyzed hydrolysis of high concentration olive oil in AOT-isooctane reversed micelles

Candida rugosa lipase has been used to investigate the hydrolysis of high concentration olive oil in the AOT-isooctane reversed micellar system at W(o) = 10, pH 7.1, and 37 degrees C. Results from this work show the hydrolytic reaction obeys Michaelis-Menten kinetics up to the initial substrate concentration of 1.37M, with turnover number k(cat) and Michaelis constant K(M) of 67.1 mumol/min mg enzyme and 0.717M, respectively. A competitive inhibition by the main product, oleic acid, has been found with a dissociation constant K(I) for the complex EP* of 0.089M. The rate equation was further analyzed in the time course reaction and was found in agreement with the experimental results for lower substrate concentrations, up to 0.341M. Large deviation occurred at high substrate concentrations, which may be due to the effects of large consumption of water on kinetics, on the formation of glycerol, and on the deactivation of lipase in the hydrolysis reaction as well.     

Enzymatic production of cyclodextrins from milled corn starch in an ultrafiltration membrane bioreactor

Cyclodextrin glycosyltransferase (CGTase) was found to be severely inhibited by cyclodextrins. In order to increase the conversion yield by reducing product inhibition and reuse the CGTase in the production of cyclodextrins from milled corn starch, an ultrafiltration membrane bioreactor system was employed. In a batch operation with ultrafiltration, the conversion yield was increased 57% compared with that without ultrafiltration. Operating conditions for the continuous production of cyclodextrins in the membrane bioreactor were optimized by taking into consideration the filtration rate and the conversion yield as follows: initial starch concentration, 7% (w/v); starch feeding rate, 240 mg/h; CGTase loading, 350 units/initial gram starch. When cyclodextrins were continuously produced in the membrane bioreactor under optimized conditions, 340 units of CGTase was require to produce 1 g of cyclodextrins for 48 h, while in the case of conventional batch operation, 1 g of cyclodextrins was produced for 24 h by 1410 units of CGTase. (c) 1993 John Wiley & Sons, Inc.     

Dipeptide synthesis and separation in a reversed micellar membrane reactor

The synthesis of dipeptide AcPheLeuNH₂ catalyzed by α-chymotrypsin encapsulated in TTAB/octanol/heptane reversed micelles was investigated in a tubular ceramic membrane reactor, operated in a batch mode. The reaction medium conditions (TTAB concentration, buffer molarity, and pH) were optimized using a factorial design in order to achieve maximum synthesis rates. Hydrated reversed micelles permeated through the membrane together with the substrate ester, dipeptide, and by-products. However, as a result of the low solubility of the peptide in the reaction medium, selective precipitation occurred, thus enabling the complete retention of the solid product by the ultrafiltration membrane and therefore an integration of a separation step in the biotransformation process. In spite of the continuous accumulation of solids inside the reactor, constant permeation flow rates could be maintained throughout the operation. The influence of α-chymotrypsin, TTAB, and water concentration on the kinetics and mass transfer of the system was also investigated. The behavior of the system during a continuous experiment was also evaluated.     

Continuous glycerolysis of olive oil by Chromobacterium viscosum lipase immobilized in liposome in reversed micelles

Chromobacterium viscosum lipase which has adsorbed on liposome and solubilized in microemulsion droplets of glycerol containing a little amount of water could catalyze the glycerolysis of olive oil. Studies on the continuous glycerolysis of olive oil by the immobilized enzyme was done at 37 degrees C in continuous stirred vessel bioreactor with polysulfone membrane. The effect of the flow rate of substrate (olive oil) in isooctane on the conversion and composition of the outlet was investigated using high-performance liquid chromatography (HPLC). The conversion increased with decrease in the flow rate. And we studied the effect of water content in the glycerol-water-lipase solution on the glycerolysis reaction. The conversion to desirable products, mono- and di-olein, was improved without a substantial production of oleic acid at lower water concentrations, i.e., below 8.0% (w/v) which corresponds to a w(o) value of 0.97. At water concentration higher than 8.0% (w/v), the amount of free fatty acid was dramatically increased. Higher operational stability of the enzyme reactor, and the half-line of the enzyme continuous reaction was about 7 weeks.     

反胶束萃取酶蛋白的研究进展

反胶束萃取是一项新的分离技术,不仅具有高选择性,而且不易使酶蛋白失活,在提取纯化生物活性物质方面具有巨大的工业应用潜力。本文综述了近年来该方面研究的新进展。     

Optimal operating policy of the ultrafiltration membrane bioreactor for enzymatic hydrolysis of cellulose

The dilution rate of an ultrafiltration membrane bioreactor in the enzymatic hydrolysis of cellulose was optimized using the kinetic model developed by Fan and Lee.(4) The sequence of optimal dilution rates was found to generally consist of an initial period of a minimal value (batch period), a subsequent period of maximum dilution rate, a period of a second batch, and a final period of a singular dilution rate. The effects of operating conditions, such as beta-glucosidase activity, operating time, maximum dilution rate, substrate feeding rate, and enzyme-to-substrate ratio on both the conversion yield and the sequence of optimal dilution rates were investigated. To evaluate the validity of kinetic model employed in this work, enzymatic hydrolysis was carried out using alpha-cellulose as a substrate in the ultrafiltration membrane bioreactor. The experimental data were well consistent with the simulation results. (c) 1993 John Wiley & Sons, Inc.     

Performance of a cutinase membrane reactor for the production of biodiesel in organic media

The enzymatic transesterification of oils with an alcohol, using recombinant cutinase of Fusarium solani pisi microencapsulated in sodium bis(2-ethylhexyl) sulfosuccinate (AOT)/isooctane reversed micelles, was performed in a membrane bioreactor (MBR). A tubular ceramic membrane with a nominal molecular weight cut off of 15,000 Da was used to retain the enzyme, and characterized in terms of rejection coefficients of the reaction components by transmission experiments. The performance of the MBR in a total recirculation-batch mode was compared with results obtained in a stirred batch tank reactor. The continuous operation of the MBR was also evaluated and the influence of the alcohol type and permeate flow rate on conversion degree and productivity (up to 500 g(product) /day/g(enzyme) was attained) were analyzed. Cutinase wild type and mutant T179C were tested for this process and the high long-term operational stability of the cutinase mutant demonstrated its potential as biocatalyst for the enzymatic continuous production of biodiesel.     

Catalytic and interfacial aspects of enzymatic polymer synthesis in reversed micellar systems

The enzyme horseradish peroxidase, when encapsulated in reversed micelles, is capable of catalyzing the synthesis of phenolic and aromatic amine polymers. The synthesis of polyethylphenol is specifically considered in this article and is found to be extremely feasible in the micellar system. Polymer chain growth can be controlled to some degree by manipulating the ability of the solvent to sustain chain solubility; this is effectively done by adjusting the surfactant concentration. This results in a degree of control of polymer molecular weight. The synthesized polymer drops out of solution and can be easily recovered. (c) 1993 John Wiley & Sons, Inc.     

Application of a 22L scale membrane bioreactor and cross-flow ultrafiltration to obtain purified chondroitin

Recently, the possibility of producing fructosylated chondroitin from the capsular polysaccharide of Escherichia coli O5:K4:H4, in fed‐batch and microfiltration experiments was assessed on a 2 L bioreactor. In this work, a first scale‐up step was set on a 22 L membrane reactor with modified baffles to insert ad hoc designed microfiltration modules permanently inside the bioreactor vessel. Moreover, the downstream polysaccharide purification process, recently established on the A¨?KTA cross‐flow instrument, was translated to a UNIFLUX‐10, a tangential flow filtration system suitable for prepilot scale. In particular, the microfiltered permeates obtained throughout the fermentation, and the supernatant recovered from the centrifuged broth at the end of the process, were treated as two separate samples in the following ultrafiltration procedure, and the differences in the two streams and how these affected the ultrafiltration/diafiltration process performance were analysed. The total amount of K4 capsular polysaccharide was about 85% in the broth and 15% in the microfiltered permeates. However, the downstream treatment was more efficient when applied to the latter. The major contaminant, the lipopolysaccharide, could easily be separated by a mild hydrolysis that also results in the elimination of the unwanted fructosyl residue, which is linked to the C‐3 of glucuronic acid residues. The tangential ultrafiltration/diafiltration protocols developed in a previous work were effectively scaled‐up, and therefore in this research proof of principle was established for the biotechnological production of chondroitin from the wild‐type strain E. coli O5:K4:H4. The complete downstream procedure yielded about 80% chondroitin with 90% purity. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 28: 1012–1018, 2012     

Immobilization of Candida rugosa lipase on polypropylene microfiltration membrane modified by glycopolymer: hydrolysis of olive oil in biphasic bioreactor

Polypropylene hollow fiber microfiltration membranes (PPHFMM) with improved hydrophilicity and biocompatibility surface were prepared by the plasma-induced graft polymerization of -allyl glucoside and were used to immobilize lipase from Candida rugosa by adsorption. A biphasic enzyme membrane bioreactor (EMR) was assembled with the glycopolymer-modified and enzyme-immobilized PPHFMM. Effect of operating variables on the performance of this biphasic EMR was investigated with the hydrolysis of olive oil. It was found that, at the optimal operational condition, an apparent volumetric reaction rate of about 0.074 mmol/l h can be obtained. This result indicated that the lipase-immobilized PPHFMM exhibited the catalytic efficiency similar to that of some hydrophilic membranes in biphasic EMR, which verified the feasibility of the employment of surface-hydrophilized polypropylene membranes in such EMR.     

Use of alkaline proteases for ultrafiltration membrane cleaning

Ability of alkaline proteases to clean ultrafiltration membranes fouled during milk processing was determined in two alkaline UF membrane cleaner, Alconox and Ultrasil. Optimum hydrolysis of milk proteins was observed with 5 g enzyme/l and showed a linear increase in water flux from 37.6 l m–2 h to 212.4 l m–2 h after 0.67 h. Enzyme performance was synergistically enhanced in combination with Alconox cleaner and exhibited 100% flux restoration.     

Biocatalytic transesterification of triglycerides and alcohols for the production of biodiesel using cutinase in organic media

Abstract

The world's energy supply is mainly composed of fossil fuels, which are a non-renewable source of energy that is rapidly running out. To overcome this concern, industry has been focusing on the production of biofuels such as biodiesel. A range of approaches has been considered to transform oils into applicable biodiesel: dilutions, microemulsifications, pyrolysis and transesterification. The latter method consists of the conversion of triglycerides to a mixture of alkyl esters and glycerol, in the presence of an acyl acceptor and a catalyst. Due to high selectivity when using enzymes as catalysts, and mild operating conditions, biocatalytic transesterification has proven to be an efficient method. Cutinase, from the superfamily α/β hydrolases, is an enzyme with lipolytic activity that effectively catalyses transesterification reactions. This article highlights the use of cutinase microencapsulated in bis(2ethylhexyl) sodium sulfosuccinate (AOT)-reversed micelles to perform the biocatalytic transesterification of triglycerides, with low chain-length alcohols (e.g. methanol), in organic media to produce biodiesel.     

A novel biphasic extractive membrane bioreactor for minimization of membrane-attached biofilms

Extractive membrane bioreactor (EMB) systems offer a means of biologically treating wastewaters, but, like other membrane processes, are constrained by their tendency to be fouled by membrane-attached biofilms (MABs). This study describes a new approach to eradicate MAB formation and accumulation in EMB systems. To this end, an innovative EMB configuration, the biphasic extractive membrane bioreactor (BEMB), has been developed. In BEMB systems, the two main constituents of the EMB process, membrane and bacteria, are kept separated and interact via a suitable recirculating solvent. Nineteen candidate solvents were tested to assess their suitability for BEMB application. Based on the results of the solvent selection, guidelines are provided to screen solvents for BEMB application. BEMB and EMB runs were carried out to demonstrate the effectiveness of BEMB technology in avoiding MAB accumulation and to compare BEMB and EMB performance. A synthetic wastewater containing monochlorobenzene (MCB) was used as a model system. Abiotic BEMB and EMB runs were carried out and used as comparative references for estimating the effect of MAB accumulation on system performance. MAB thickness in the BEMB systems was controlled at 18 microm during 1 month of operation, whereas, in the EMB systems, MAB thickness reached 1250 microm. Analysis of mass transport in EMB and BEMB systems revealed that the high affinity of the permeating molecules for the solvent may contribute to a reduction in shell-side mass transfer resistance. This reduction of shell-side mass transfer resistance and the absence of MAB accumulation led to overall mass transfer coefficients of about sevenfold greater (4.5 x 10(-5) m s(-1)) in the BEMB system than in the EMB system (0.6 x 10(-5) m s(-1)).     

Dual-chambered membrane bioreactor for coculture of stratified cell populations

We have developed a dual-chambered bioreactor (DCB) that incorporates a membrane to study stratified 3D cell populations for skin tissue engineering. The DCB provides adjacent flow lines within a common chamber; the inclusion of the membrane regulates flow layering or mixing, which can be exploited to produce layers or gradients of cell populations in the scaffolds. Computational modeling and experimental assays were used to study the transport phenomena within the bioreactor. Molecular transport across the membrane was defined by a balance of convection and diffusion; the symmetry of the system was proven by its bulk convection stability, while the movement of molecules from one flow line to the other is governed by coupled convection-diffusion. This balance allowed the perfusion of two different fluids, with the membrane defining the mixing degree between the two. The bioreactor sustained two adjacent cell populations for 28 days, and was used to induce indirect adipogenic differentiation of mesenchymal stem cells due to molecular cross-talk between the populations. We successfully developed a platform that can study the dermis–hypodermis complex to address limitations in skin tissue engineering. Furthermore, the DCB can be used for other multilayered tissues or the study of communication pathways between cell populations.     

Kinetics of lipase-catalyzed hydrolysis of olive oil in AOT/isooctane reversed micelles

The kinetics of lipase-catalyzed hydrolysis of olive oil in AOT/isooctane reversed micellar media was studied. It was shown that the deactivation of lipase had a great influence on the reaction kinetics. Based on whether the enzyme deactivation and influences of both product and substrate on enzyme stability were included or not, four different kinetic models were established. The simulating results demonstrated that the kinetic model, which including product inhibition, enzyme deactivation and the improvements of lipase stability by both product and substrate, fit the experimental data best with an overall relative error of 4.68%.     

Lipase-catalyzed hydrolysis of olive oil in chemically-modified AOT/isooctane reverse micelles in a hollow fiber membrane reactor

The hydrolysis of olive oil catalyzed by Candida rugosa lipase in sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/isooctane and the synthetic sodium bis(2-ethylhexyl polyoxyethylene)sulfosuccinate (MAOT)/isooctane reverse micellar systems was investigated in a polysulfone hollow fiber membrane reactor with recycle of the reaction mixture. Lipase was completely retained by the membrane while olive oil and oleic acid freely passed through. The retention of reverse micelles depended on W ₀ (molar ratio of water to surfactant). At an olive oil concentration of 0.23 mol l^–1 the final substrate conversion in the MAOT micellar system was about 1.4 times of that in the AOT micellar system.     

Biodegradation of BTEX vapors in a silicone membrane bioreactor system

The biotreatment of complex mixtures of volatile organic compounds (VOCs) such as benzene, toluene, ethylbenzene, and xylene isomers (BTEX) has been investigated by many workers. However, the majority of the work has dealt with the treatment of aqueous or soil phase contamination. The biological treatment of gas and vapor phase sources of VOC wastes has recently received attention with increased usage of biofilters and bioscrubbers. Although these systems are relatively inexpensive, performance problems associated with biomass plugging, gas channeling, and support media acidification have limited their adoption. In this report we describe the development and evaluation of an alternative biotreatment system that allows rapid diffusion of both BTEX and oxygen through a silicone membrane to an active biofilm. The bioreactor system has a rapid liquid recycle, which facilitates nutrient medium mixing over the biofilm and allows for removal of sloughing cell mass. The system removed BTEX at rates up to 30 μg h⁻¹ cm⁻² of membrane area. BTEX removal efficiencies ranged from 75% to 99% depending on the BTEX concentration and vapor flowrate. Consequently, the system can be used for continuous removal and destruction of BTEX and other potential target VOCs in vapor phase streams. Journal of Industrial Microbiology & Biotechnology (2001) 26, 316–325. Received 14 August 2000/ Accepted in revised form 28 February 2001     

Concentration-driven reverse membrane bioreactor for the fermentation of highly inhibitory lignocellulosic hydrolysate

Optimal production of lignocellulosic bioethanol is hindered due to commonly faced issues with the presence of inhibitory compounds and sequentially consumed sugars in the lignocellulosic hydrolysate. Therefore, in order to find a robust fermentation approach, this study aimed at enhancing simultaneous co-assimilation of sugars, and inhibitor tolerance and detoxification. Therefore, fermentation of toxic wheat straw hydrolysate containing up to 20 g/l furfural, using the concentration-driven diffusion-based technique of reverse membrane bioreactor (rMBR) was studied. The rMBR fermentation of the hydrolysate led to complete furfural detoxification and the conversion of 87 % of sugars into ethanol at a yield of 0.48 g/g. Moreover, when the toxicity level of the hydrolysate was increased to 9 g/l of initial furfural, the system responded exceptionally by reducing 89 % of the inhibitor while only experiencing about 25 % drop in the ethanol yield. In addition, using this diffusion-based set-up in extremely inhibitory conditions (16 g/l furfural), cells could detoxify 40 % of the furfural at a high initial furfural to cell ratio of 9.5:1. The rMBR set-up applied proved that by properly synchronizing the medium condition, membrane area, and inhibitor to cell ratio, some of the shortcomings with conventional lignocellulosic fermentation can be tackled, guaranteeing a robust fermentation.