Ion-Conductive Poly(vinyl alcohol)-Based IPMCs

Partially crosslinked and sulfonated poly(vinyl alcohol) (s-PVA) membranes were prepared as ion-conductive matrices of Ionic Polymer-Metal Composite (IPMC) and a new IPMC based on the s-PVA membrane was fabricated via an electroless plating procedure of platinum. PVA was reacted with sulfosuccinic acid (SSA) as a crosslinking agent with a sulfonic group and 4-(2-hydroxyethyl)piperazine-1-propanesulfonic acid (EPPS) as a side chain with a sulfonic group. The crosslinked s-PVA membranes were characterized using a FT-IR spectroscope and a scanning electron microscope-combined energy-dispersive X-ray spectrometer and were assessed in terms of water absorption, proton conductivity, and the feasibility of electroless plating. Among the prepared ionomers, the s-PVA membrane obtained at 20 wt.% SSA and 10 wt.% EPPS (S20E10 membrane) registered the highest proton conductivity of 2.9 × 10^?2 S·cm^?1, which corresponds to one third of that of Nafion series, and only the S20E10 membrane was successfully plated via the electroless plating method without any crack and broken part. The s-PVA-based IPMC showed the one-directional displacement with 1-minute-long time-lapse comparable to typical Nafion-based IPMCs. However, the displacement under an AC potential was very limited due to its slow deformation response and the actuation performance was severely varied with actuation time including the short service life of several minutes in air. The short and variable actuation of the s-PVA-based IPMC was attributed to its large variation of surface and ionic resistances during air-operation, which is induced by the low ratio of bound to free water.     

Advanced Electro-active Dry Adhesive Actuated by an Artificial Muscle Constructed from an Ionic Polymer Metal Composite Reinforced with Nitrogen-doped Carbon Nanocages

An advanced electro-active dry adhesive,which was composed of a mushroom-shaped fibrillar dry adhesive array actuated by an Ionic Polymer Metal Composite (IPMC) artificial muscle reinforced with nitrogen-doped carbon nanocages (NCNCs),was developed to imitate the actuation of a gecko's toe.The properties of the NCNC-reinforced Nafion membrane,the electromechanical properties of the NCNC-reinforced IPMC,and the related electro-active adhesion ability were investigated.The NCNCs were uniformly dispersed in the 0.1 wt％ NCNC/Nafion membrane,and there was a seamless connection with no clear interface between the dry adhesive and the IPMC.Our 0.1 wt％ NCNC/Nafion-IPMC actuator shows a displacement and force that are 1.6-2 times higher than those of the recast Nafion-IPMC.This is due to the increased water uptake (25.39％) and tensile strength (24.5 MPa) of the specific 3D hollow NCNC-reinforced Nafion membrane,as well as interactions between the NCNCs and the sulfonated groups of the Nafion.The NCNC/Nafion-IPMC was used to effectively actuate the mushroom-shaped dry adhesive.The normal adhesion forces were 7.85 mN,12.1 mN,and 51.7 mN at sinusoidal voltages of 1.5 V,2.5 V,and 3.5 V,respectively,at 0.1 Hz.Under the bionic leg trail,the normal and shear forces were approximately 713.5 mN (159 mN·cm-2) and 1256.6 mN (279 mN·cm-2),respectively,which satisfy the required adhesion.This new electro-active dry adhesive can be applied for active,distributed actuation and flexible grip in robots.     

Preparation of gradually componential metal electrode on solution-casted Nafion membrane

A typical ionic polymer-metal composite consists of a thin perfluorinated ionomer membrane and noble metal electrodes plated on both surfaces. It undergoes a large bending motion when an electric field is applied hence exhibits deformation by a certain amount of cation. With proper arrangement and package, a great number of "smart devices" are anticipated. In this study, a solution-cast route was used to prepare the electro-active polymer membrane and platinum electrodes were fabricated onto the membrane through electro-less plating. The ionic polymer used is the commercial Nafion, the perfluoro-sulfonated ionomer membrane, developed by DuPont Co. Nafion membrane was cast by the solution-casting route and then loaded with different weights simultaneously. The optimized processing conditions, membrane properties and electrodes behaviors were investigated. The results of shift in WAXD peaks showed that weights delineated the crystallinity of the solution-cast membranes. The number and size of the crystalline domains of solution-cast membrane decrease as studied by SAXS. The Young's modulus of solution-cast membrane decreases as increasing weight because of the loss of crystallinity (180-140 MPa). A finely dispersed platinum particle deeper and gradient penetrating within the near-boundary region with a smaller average particle size and more uniform distribution could be obtained through a reverse electro-less plating. Its surface roughness is 3 nm comparing to 52 nm of a typical process. But its surface resistance is too high (3.5 Omega) to activate the bending motion. To solve this problem, we coated the second Pt electrodes by a typical electro-less plating, and the resistance decreased to 0.7 Omega. The results depicted that the fabricated IPMC shows longer bending lifetime than typical IPMC. In a 0.09% NaCl solution, the device was able to vibrate for 8h under a 5 V, 0.1 Hz actuation.     

Investigation of Ionic Polymer Metal Composite Actuators Loaded with Various Tetraethyl Orthosilicate Contents

Ionic Polymer Metal Composite (IPMC) can be used as an electrically activated actuator,which has been widely used in artificial muscles,bionic robotic actuators,and dynamic sensors since it has the advantages of large deformation,light weight,flexibility,and low driving voltage,etc.To further improve the mechanical properties of IPMC,this paper reports a new method for preparing organic-inorganic hybrid Nafion/SiO2 membranes.Beginning from cast Nation membranes,IPMCs with various tetraethyl orthosilicate (TEOS) contents were fabricated by electroless plating.The elastic moduli of cast Nation membranes were measured with nano indenters,the water contents were calculated,and the cross sections of Nafion membranes were observed by scanning electron microscopy.The blocking force,the displacement,and the electric current of IPMCs were then measured on a test apparatus.The results show that the blocking force increases as the TEOS content gradually increases,and that both the displacement and the electric current initially decrease,then increase.When the TEOS content is 1.5％,the IPMC shows the best improved mechanical properties.Finally,the IPMC with the best improved performance was used to successfully actuate the artificial eye and tested.     

Molecular dynamics simulations of Nafion and sulfonated polyether sulfone membranes. I. Effect of hydration on aqueous phase structure

We measured the water uptakes and proton conductivities of a Nafion membrane and three sulfonated polyether sulfone membranes (SPESs) with different values of ion-exchange capacity (IEC = 0.75, 1.0 and 1.4 meq/g) in relation to relative humidity in order to apply the findings to polymer electrolyte membrane fuel cells. The number of water molecules per sulfonic acid group λ at each humidity level was independent of the relative humidity for all membranes, but the proton conductivities of the SPESs were inferior to that of Nafion for the same λ value. Classical molecular dynamics simulations for the same membranes were carried out using a consistent force field at λ = 3, 6, 9, 12 and 15. The structural properties of water molecules and hydronium ions at a molecular level were estimated from radial distribution functions and cluster size distributions of water. We found that the radial distribution function of S(sulfonic acid)–S(sulfonic acid) of Nafion at λ = 3 indicated a significant correlation between the S–S pair, due to water channels, while the S–S pair of the SPESs showed a poor correlation. The cluster size distribution of water was also calculated in order to estimate the connectivity of the water channel. It is clear that some water is present in the SPESs as small, isolated clusters, especially when the water content is low.     

Ethylene formation from 1-aminocyclopropane-1-carboxylic acid by microsomal membranes from senescing carnation flowers

Isolated membranes from the petals of senescing carnation flowers (Dianthus caryophyllus L. cv. White-Sim) catalyze the conversion of 1-aminocyclopropane-1-carboxylic acid (ACC) to ethylene. A microsomal membrane fraction obtained by centrifugation at 131,000 g for 1 h proved to be more active than the membrane pellet isolated by centrifugation at 10,000 g for 20 min. The ethylene-producing activity of the microsomal membranes is oxygen-dependent, heat-denaturable, sensitive to n-propyl gallate, and saturable with ACC. Corresponding cytosol fractions from the petals are incapable of converting ACC to ethylene. Moreover, the addition of soluble fraction back to the membrane fraction strongly inhibits the ACC to ethylene conversion activity of the membranes. The efficiency with which isolated membranes convert ACC to ethylene is lower than that exhibited by intact flowers based on the relative yield of membranes per flower. This may be due to the presence of the endogenous soluble inhibitor of the reaction, for residual soluble fraction inevitably remains trapped in membrane vesicles isolated from a homogenate.Abbreviations ACC 1-aminocyclopropane-1-carboxylic acid - AOA aminoxyacetic acid - AVG aminoethoxyvinylglycine - EPPS N-2-hydroxyethylpiperazine propane sulfonic acid     

Toxicity of Influenza A Virus Matrix Protein 2 for Mammalian Cells is Associated with its Intrinsic Proton-Channeling Activity

Molecules of influenza matrix protein 2 (M2) are organized in tetramers that constitute a well-conserved virion component and also form proton channels in the plasma membrane of infected cells. In this report we demonstrate that influenza M2 protein is cytopathic in vitro for mammalian cells. An M2 point-mutant (M2pm) protein was constructed that contained amino acid changes designed to block the proton channel via introduction of large hydrophobic residues. This mutant was significantly less toxic upon transient transfection in vitro than the wild-type M2 (M2wt). To assess the possible correlation between M2 cytotoxicity and its proton channel activity, we monitored changes in mitochondria membrane potential induced by M2wt and M2pm. M2wt rapidly decreased mitochondria membrane potential reflecting the transmembrane proton gradient, while M2pm was markedly less efficient. Thus, M2 is cytotoxic for mammalian cells, likely via its proton channel activity and may therefore contribute to influenza pathogenesis through this previously unknown mechanism.     

Verification of Beam Models for Ionic Polymer-Metal Composite Actuator

Ionic Polymer-Metal Composite (IPMC) can work as an actuator by applying a few voltages.A thick IPMC actuator,whereNafion-117 membrane was synthesized with polypyrrole/alumina composite filler,was analyzed to verify the equivalent beamand equivalent bimorph beam models.The blocking force and tip displacement of the IPMC actuator were measured with a DCpower supply and Young’s modulus of the IPMC strip was measured by bending and tensile tests respectively.The calculatedmaximum tip displacement and the Young’s modulus by the equivalent beam model were almost identical to the correspondingmeasured data.Finite element analysis with thermal analogy technique was utilized in the equivalent bimorph beam model tonumerically reproduce the force-displacement relationship of the IPMC actuator.The results by the equivalent bimorph beammodel agreed well with the force-displacement relationship acquired by the measured data.It is confirmed that the equivalentbeam and equivalent bimorph beam models are practically and effectively suitable for predicting the tip displacement,blockingforce and Young’s modulus of IPMC actuators with different thickness and different composite of ionic polymer membrane.     

Significantly Enhanced Actuation Performance of IPMC by Surfactant-Assisted Processable MWCNT/Nafion Composite

The performance of Ionic Polymer Metal Composite (IPMC) actuator was significantly enhanced by incorporating surfactant-assisted processable Multi-Walled Carbon Nanotubes (MWCNTs) into a Nafion solution. Cationic surfactant Cetyl Trimethyl Ammonium Bromide (CTAB) was employed to disperse MWCNTs in the Nafion matrix, forming a homogeneous and stable dispersion of nanotubes. The processing did not involve any strong acid treatment and thus effectively preserved the excellent electronic properties associated with MWCNT. The as-obtained MWCNT/Nafion-IPMC actuator was tested in terms of conductivity, bulk and surface morphology, blocking force and electric current. It was shown that the blocking force and the current of the new IPMC are 2.4 times and 1.67 times higher compared with a pure Nafion-based IPMC. Moreover, the MWCNT/IPMC performance is much better than previously reported Nafion-IPMC doped by acid-treated MWCNT. Such significantly improved performance should be attributed to the improvement of electrical property associated with the addition of MWCNTs without acid treatment.     

The structural and functional analysis of the surface apparatus in four species of Sarcocystis (Sporozoa, Apicomplexa)

The comparable ultrastructural analysis of the sarcocyst surface apparatus (SSA) was made for four species of Sarcocystis: Sarcocystis muris, S. fusiformis, S. medusiformis, and Sarcocystis sp. from buffalo heart muscles. In all these species, SSA contains a surface membrane, overmembrane complex with glycocalyx, and submembrane complex made of two glycoprotein SSA primembrane layers. SSA makes numerous primary vesicle-like protrusions and pits in between. Some vesicles containing two layers, PM1 and PM2, are pinching off from the totally formed protrusions. Then these vesicles are directed into infected host cell to participate in its degradation. In the SSA pits neither over-, nor submembrane complex is present, the pits being made of the surface membrane only. It is important that fibrillar structures penetrate through the SSA membrane into pits from the host cell. Besides, SSA forms secondary protrusions with different structures in various species of Sarcocystis. They increase the sarcocyst surface and transport different substances along intermediate filaments from the SSA pits membrane to the sarcocyst body. At the same time, deep invaginations are found in the SSA of old sarcocysts. We thought that these structures increased the sarcocyst surface and thus promote to intensify metabolism. This study-defined presence of membranous vesicles in secondary protrusions. According to their structure and localization, the membranous vesicles may be involved in the building of the sarcocyst surface membrane.     

Organogenesis of stem and leaf protoplasts of a haploid golden delicious apple clone (Malus Xdomestica Borkh.)

Summary Highly viable protoplasts were isolated in large numbers from in vitro-grown leaf and stem tissues of a haploid clone of the apple scion cultivar Golden Delicious (Malus Xdomestica Borkh.). Protoplasts from both sources divided rapidly to give microcallus, when cultured in a modified Kao and Michayluk-based medium. Following two successive subcultures for callusing, shoot buds were regenerated from such calli, on half-strength Murashige and Skoog medium with an increased concentration of group B vitamins and containing 5.0 mg.l^-1 6-benzyl-aminopurine and 0.1 mg.l^-1 l-naphthaleneacetic acid (for the leaf protoplast-derived calli) or 4-indole-3yl-butyric acid (for stem protoplast-derived calli). The mesophyll protoplast-derived shoots were enfeebled and vitrified, in time with their ultimate death. Conversely, for those shoots deriving from the stem protoplasts, in vitro propagation was successfully achieved. This is the first report on the successful isolation, culture and organogenesis from stem protoplasts of a woody plant genotype.Abbreviations BAP 6-benzylaminopurine - FPE final plating efficiency - IBA 4-indole-3yl-butyric acid - IPE initial plating efficiency - f wt fresh weight - KM Kao and Michayluk (1975) - MES 2-N-morpholino ethane sulfonic acid - MPE intermediate plating efficiency - MS Murashige and Skoog (1962) - NAA l-naphthaleneacetic acid - PVP-10 polyvinylpyrrolidone (Av MW 10,000)     

Biomimetic robotic Venus flytrap (Dionaea muscipula Ellis) made with ionic polymer metal composites

The work described in this paper is a novel design of a robotic Venus flytrap (VFT) (Dionaea muscipula Ellis) by means of ionic polymeric metal composite (IPMC) artificial muscles as distributed nanosensors and nanoactuators. Rapid muscular movements in carnivorous plants, such as VFT, which are triggered by antenna-like sensors (trigger hair), present a golden key to study distributed biomolecular motors. Carnivorous plants, such as VFT, possess built-in intelligence (trigger hairs), as a strategy to capture prey, that can be turned on in a controlled manner. In the case of the VFT, the prey that is lured by the sweet nectar in the VFT pair of jaw-like lobes has to flip and move the trigger hairs, which are colorless, bristle-like and pointed. The dynamically moved trigger hairs then electro-elastically send an electric signal to the internal ions in the lobe to migrate outwardly for the jaw-like lobes to close rapidly to capture the prey. The manner in which the VFT lobes bend inward to capture the prey shows a remarkable similarity with typical IPMCs bending in an electric field. Furthermore, the mechano-electrical sensing characteristics of IPMCs also show a remarkable resemblance to mechano-electrical trigger hairs on the lobes of the VFT. The reader is referred to a number of papers in connection with sensing and actuation of IPMCs in particular. Thus, one can integrate IPMC lobes with a common electrode in the middle of one end of the lobes to act like a spine and use IPMC bristles as trigger finger to sense the intrusion of a fly or insect to send a sensing signal to a solid state relay which then triggers the actuation circuit of the IPMC lobes to rapidly bend toward each other and close. The two lobes, which form the trap, are attached to the midrib common electrode which is conveniently termed the spine. The upper surface of each lobe is dished, and spaced along the free margins of the lobes with some 15-20 prong-like teeth. These are tough and pointed, and are inclined at an inward angle so that when the trap is sprung shut they will interlock. We have been experimenting with the VFT closing of its jaw-like lobes that close in about 0.3 s and have gained a lot of knowledge to report on the ionic and electrical mechanisms involved in the operation of such intelligent distributed biomolecular motors.     

Membrane proton conductivity and energy-dependent fluxes of hydrogen ions in bacteria Enterococcus hirae grown in media with different pH values

It was shown that the proton conductivity of Enterococcus hirae ATCC9790 membrane increases three times as pH of the growth medium decreases from 8.5 to 5.5. The changes in proton conductivity are interrelated to the values of membrane and redox potentials of the cell, which in turn vary depending on the pH value of growth medium. The energy-dependent H+ efflux for cells fermenting sugar (the glucose) decreases 1.5 times as pH decreases from 8.5 to 5.5; in this case, the N,N'-dicyclohexylcarbodiimide at lower pH values suppresses the H+ efflux more intensively than at higher pH values, the H+ efflux nonsensitive to N,N'-dicyclohexylcarbodiimide being practically unchanged. The H+ efflux in the ATPase mutant MS116 is significantly (approximately 3 times) lower than that in the precursor strain and does not depend on pH. The results show that the proton conductivity of the membrane of this bacterium depends on pH of the growth medium. It is possible that the energy-dependent H+ efflux through F1F0-ATPase is interrelated with membrane proton conductivity.     

The role of the sarcocyst surface apparatus in utilizing the host cell muscle structures

The participation of the sarcocyst surface apparatus (SSA) of two sarcosporidian species, Sarcocystis muris and S. ovifelis (Coccidia, Sporozoa, Apicomplexa), in degradation of disrupted host cell substances was investigated. After degradation, these substances are transported through the membrane of the SSA to the sarcocyst ground substance (GS), but this process cannot be regarded as endocytosis. At first, the transported substances were found in SSA pits in the form of fibrillar structures. Later on, these were seen as twisted up granules. In some cases, such granules restore their fibrillar shape, penetrate through the SSA membrane and appear in the sarcocyst GS. In other cases, the small granules may be released from SSA pits directly to the sarcocyst GS. Besides, two SSA primembrane layers were seen to disappear during the transportation of host cell substances. In addition, multimembrane structures (membranous whorls) were first demonstrated between the plasmalemma and inner membrane complex of the zoite pellicle. Multimembrane structures were found, in addition, in the zoite cytoplasm in connection with micronemes. These structures resembling chloroplast granae of thylakoids may presumably fill the gap in membrane pool of the SSA contributing to its renewal.     

Effects of Crosslinking Agent-DFDNB on Energy-transducing Reactions of Chloroplast Thylakoid Membrane Proteins

The effects of crosslinking agent-DFDNB (difluoro dinitro benzene) on functions of chloroplast thylakoid membrane proteins were investigated. DFDNB inhibited activities of PSP and membrane-bound ATPase in chloroplasts. It decreased proton uptake of light-inducted chloroplast thylakoids and the relative value of fluorescence quenching of 9-aminoacridine, and inhibited the rate of fast electrogenic phase of absorption change at 515 nm in chloroplasts. In addition, the isolated CF1-ATPase was crosslinked with DFDNB. The pattern of polymers of crosslinked CF1-ATPase was observed on SDS-PAGE.     

Proton exclusion by an aquaglyceroprotein: a voltage clamp study

BACKGROUND INFORMATION: In silico both orthodox aquaporins and aquaglyceroporins are shown to exclude protons. Supporting experimental evidence is available only for orthodox aquaporins. In contrast, the subset of the aquaporin water channel family that is permeable to glycerol and certain small, uncharged solutes has not yet been shown to exclude protons. Moreover, different aquaglyceroporins have been reported to conduct ions when reconstituted in planar bilayers. RESULTS: To clarify these discrepancies, we have measured proton permeability through the purified Escherichia coli glycerol facilitator (GlpF). Functional reconstitution into planar lipid bilayers was demonstrated by imposing an osmotic gradient across the membrane and detecting the resulting small changes in ionic concentration close to the membrane surface. The osmotic water flow corresponds to a GlpF single channel water permeability of 0.7x10(-14) cm(3).subunit(-1).s(-1). Proton conductivity measurements carried out in the presence of a pH gradient (1 unit) revealed an upper limit of the H(+) (OH(-)) to H(2)O molecules transport stoichiometry of 2x10(-9). A significant GlpF-mediated ion conductivity was also not detectable. CONCLUSIONS: The lack of a physiologically relevant GlpF-mediated proton conductivity agrees well with predictions made by molecular dynamics simulations.     

Interaction of membrane proton conductivity,membrane and oxidation-reduction potential in Escherichia coli

It was shown that the proton conductivity of Escherichia coli membranes depends on pH and other conditions of bacterial growth. It is considerably lower in cells fermenting glucose and accomplishing the nitrate-nitrite respiration compared with cells accomplishing the oxygen respiration. Proton conductivity increases substantially with decreasing pH of medium. It was found that proton conductivity is related to the redox and membrane potentials of cells. The energy-dependent flux of protons from cells and the ATPase activity of membrane vesicles considerably vary depending on whether bacteria are grown under aerobic or anaerobic conditions. The H+ flux from cells fermenting glucose (pH 7.5) was 1.7 times greater than the H+ flux from cells that accomplish the nitrate-nitrite and oxygen respiration. The N,N'-dicyclohexylcarbodiimide (DCCD)-sensitive ATPase activity increased 2.5 times as K+ concentration increased to 100 mM (including residual K+ in potassium-free medium). The DCCD-sensitive ATPase activity considerably decreased with decreasing pH of medium, whereas the ATPase activity that was not suppressed by DCCD was stimulated. These results can be used for establishing the relationship between membrane proton conductivity and the energy-dependent H+ flux and ATPase activity.     

Insecticidal properties of Sclerotinia sclerotiorum agglutinin and its interaction with insect tissues and cells

This project studied in detail the insecticidal activity of a fungal lectin from the sclerotes of Sclerotinia sclerotiorum, referred to as S. sclerotiorum agglutinin or SSA. Feeding assays with the pea aphid (Acyrthosiphon pisum) on an artificial diet containing different concentrations of SSA demonstrated a high mortality caused by this fungal lectin with a median insect toxicity value (LC₅₀) of 66 (49–88) μg/ml. In an attempt to unravel the mode of action of SSA the binding and interaction of the lectin with insect tissues and cells were investigated. Histofluorescence studies on sections from aphids fed on an artificial liquid diet containing FITC-labeled SSA, indicated the insect midgut with its brush border zone as the primary target for SSA. In addition, exposure of insect midgut CF-203 cells to 25 μg/ml SSA resulted in a total loss of cell viability, the median cell toxicity value (EC₅₀) being 4.0 (2.4–6.7) μg/ml. Interestingly, cell death was accompanied with DNA fragmentation, but the effect was caspase-3 independent. Analyses using fluorescence confocal microscopy demonstrated that FITC-labeled SSA was not internalized in the insect midgut cells, but bound to the cell surface. Prior incubation of the cells with saponin to achieve a higher cell membrane permeation resulted in an increased internalization of SSA in the insect midgut cells, but no increase in cell toxicity. Furthermore, since the toxicity of SSA for CF-203 cells was significantly reduced when SSA was incubated with GalNAc and asialomucin prior to treatment of the cells, the data of this project provide strong evidence that SSA binds with specific carbohydrate moieties on the cell membrane proteins to start a signaling transduction cascade leading to death of the midgut epithelial cells, which in turn results in insect mortality. The potential use of SSA in insect control is discussed.     

Plant regeneration from mesophyll protoplasts of Williams' Bon Chretien (syn. Bartlett) pear (Pyrus communis L.)

Leaf protoplasts of axenic shoot cultures of Pyrus communis L. cv. Williams' Bon Chretien (syn. Bartlett) underwent cell wall regeneration and division to give multicellular colonies in a modified Murashige and Skoog medium which lacked ammonium ions, but supplemented with 1-naphthaleneacetic acid (NAA), 4-indole-3yl-acetic acid, 6-benzylaminopurine (BAP) and casein hydrolysate. Protoplast-derived colonies gave callus on Murashige and Skoog salts medium with NAA and BAP and exhibited shoot regeneration on half-strength Murashige and Skoog medium supplemented with 0.2 mg 1^–1 4-indole-3yl-butyric acid, 2.0 mg 1^–1 BAP, 0.2 mg 1^–1 gibberellic acid, 50 mg 1^–1 casein hydrolysate and 10 mg 1^–1 Ca-pantothenate. Following rooting, protoplast-derived plants of pear were transferred to the glasshouse where they completed acclimatization.Abbreviations BAP 6-benzylaminopurine - FPE final plating efficiency - GA₃ gibberellic acid - IAA 4-indole-3yl-acetic acid - IBA 4-indole-3yl-but yric acid - IPE initial plating efficiency - NAA 1-naphthaleneacetic acid - f.wt. fresh weight - MES 2-N-morpholinoethane sulfonic acid - MS Murashige and Skoog (1962) - %PE % plating efficiency - PVP-10 polyvinylpyrrolidone (Av. MW 10,000) - FDA fluorescein diacetate     

Composition of toluene-degrading microbial communities from soil at different concentrations of toluene.

Toluene-degrading bacteria were isolated from hydrocarbon-contaminated soil by incubating liquid enrichment cultures and agar plate cultures in desiccators in which the vapor pressure of toluene was controlled by dilution with vacuum pump oil. Incubation in desiccators equilibrated with either 100, 10, or 1% (wt/wt) toluene in vacuum pump oil and testing for genomic cross-hybridization resulted in four genomically distinct strains (standards) capable of growth on toluene (strains Cstd1, Cstd2, Cstd5, and Cstd7). The optimal toluene concentrations for growth of these standards on plating media differed considerably. Cstd1 grew best in an atmosphere equilibrated with 0.1% (wt/wt) toluene, but Cstd5 failed to grow in this atmosphere. Conversely, Cstd5 grew well in the presence of 10% (wt/wt) toluene, which inhibited growth of Cstd1. 16S ribosomal DNA sequencing and cross-hybridization analysis indicated that both Cstd1 and Cstd5 are members of the genus Pseudomonas. An analysis of the microbial communities in soil samples that were incubated with 10% (wt/wt) toluene with reverse sample genome probing indicated that Pseudomonas strain Cstd5 was the dominant community member. However, incubation of soil samples with 0.1% (wt/wt) toluene resulted in a community that was dominated by Pseudomonas strain Q7, a toluene degrader that has been described previously (Y. Shen, L. G. Stehmeier, and G. Voordouw, Appl. Environ. Microbiol. 64:637-645, 1998). Q7 was not able to grow by itself in an atmosphere equilibrated with 0.1% (wt/wt) toluene but grew efficiently in coculture with Cstd1, suggesting that toluene or metabolic derivatives of toluene were transferred from Cstd1 to Q7.