A Biosurfactant-Producing Pseudomonas aeruginosa Strain

A Pseudomonas aeruginosa strain producing an extracellular surfactant (biosurfactant) was isolated. The growth of this strain, referred to as 50.3, on a mineral glycerol-containing medium produces an emulsifying activity (60%) and decreases the surface tension of the culture liquid by a factor of 2.8 (to 25 mN/m). The optimum conditions for its growth and production of biosurfactants are intense aeration, pH 7.0–8.0, and the presence of Mg²⁺. The optimum biosurfactant properties were achieved when glucose was used as the only source of carbon and energy and NH₄Cl was used as a source of nitrogen. The biosurfactant was isolated from the culture liquid by extraction and precipitation.     

Effects of carbon and nitrogen sources on rhamnolipid biosurfactant production by <Emphasis Type="Italic">Pseudomonas nitroreducens</Emphasis> isolated from soil

Rhamnolipid biosurfactant production by Pseudomonas nitroreducens isolated from petroleum-contaminated soil was investigated. The effects of carbon, nitrogen and carbon to nitrogen ratio on biosurfactant production were examined using mineral salts medium as the growth medium. The tenso-active properties (surface activity and critical micelle concentrations of the produced biosurfactant were also evaluated. The best carbon source, nitrogen source were glucose and sodium nitrate giving rhamnolipid yields of 5.28 and 4.38 g l⁻¹, respectively. The maximum rhamnolipid production of 5.46 g l⁻¹ was at C/N (glucose/sodium nitrate) of 22. The rhamnolipid biosurfactant reduced the surface tension of water from 72 to ~37 mN/m. It also has critical micelle concentration of ~28 mg l⁻¹. Thus, the results presented in our reports show that the produced rhamnolipid can find wide applications in various bioremediation activities such as enhanced oil recovery and petroleum degradation.     

Optimization of low-cost biosurfactant production from agricultural residues through response surface methodology

Biosurfactants are surface-active compounds capable of reducing surface tension and interfacial tension. Biosurfactants are produced by various microorganisms. They are promising replacements for chemical surfactants because of biodegradability, nontoxicity, and their ability to be produced from renewable sources. However, a major obstacle in producing biosurfactants at the industrial level is the lack of cost-effectiveness. In the present study, by using corn steep liquor (CSL) as a low-cost agricultural waste, not only is the production cost reduced but a higher production yield is also achieved. Moreover, a response surface methodology (RSM) approach through the Box–Behnken method was applied to optimize the biosurfactant production level. The results found that biosurfactant production was improved around 2.3 times at optimum condition when the CSL was at a concentration of 1.88 mL/L and yeast extract was reduced to 25 times less than what was used in a basic soybean oil medium (SOM). The predicted and experimental values of responses were in reasonable agreement with each other (Pred-R² = 0.86 and adj-R² = 0.94). Optimization led to a drop in raw material price per unit of biosurfactant from $47 to $12/kg. Moreover, the biosurfactant product at a concentration of 84 mg/L could lower the surface tension of twice-distilled water from 72 mN/m to less than 28 mN/m and emulsify an equal volume of kerosene by an emulsification index of (E24) 68% in a two-phase mixture. These capabilities made these biosurfactants applicable in microbial enhanced oil recovery (MEOR), hydrocarbon remediation, and all other petroleum industry surfactant applications.     

Characterization and properties of biosurfactants produced by a newly isolated strain <Emphasis Type="Italic">Bacillus methylotrophicus</Emphasis> DCS1 and their applications in enhancing solubility of hydrocarbon

Six biosurfactant-producing bacteria were isolated from hydrocarbon contaminated soils in Sfax, Tunisia. Isolates were screened for biosurfactant production by different conventional methods including hemolytic activity, surface tension reduction, drop-collapsing and oil displacement tests. All these screening tests show that all the isolates behave differently. Among the isolated bacteria, DCS1 strain was selected for further studies based on its highest activities and it was identified as Bacillus methylotrophicus DCS1. This strain was found to be a potent producer of biosurfactant when cultivated in mineral-salts medium supplemented with diesel oil (2 %, v/v) as a sole carbon source. Physicochemical properties and stability of biosurfactants synthesized by B. methylotrophicus DCS1 were investigated. The produced biosurfactants DCS1, from Landy medium, possess high surface activity that could lower the surface tension of water to a value of 31 from 72 mN m^?1 and have a critical micelle concentration (CMC) of 100 mg L^?1. Compared with SDS and Tween 80, biosurfactants showed excellent emulsification activities against different hydrocarbon substrates and high solubilization efficiency towards diesel oil. Biosurfactants DCS1 showed good stability in a wide range of temperature, pH and salinity. These results suggested that biosurfactants produced by B. methylotrophicus DCS1 could be an alternative to chemically synthesized surfactants for use in bioremediation processes to enhance the solubility of hydrophobic compounds.     

Isolation and characterization of hydrocarbon-degrading and biosurfactant-producing yeast strains obtained from a polluted lagoon water

Microbial surfactants are environmentally friendly products with amazing properties and spectrum of applications. It is therefore, not surprising that research has increased in recent time with the objectives of sourcing for novel surface-active compounds with dual functions in oil and pharmaceutical industries. Evaluation of hydrocarbon degrading potentials and emulsifying activities indicated that biosurfactants were produced by two newly isolated and promising yeast strains, Saccharomyces cerevisiae and Candida albicans, obtained from a polluted lagoon water. Both strains were able to grow effectively on crude oil and diesel as sole sources of carbon and energy. Growth curves on diesel were obtained to establish the relation between cell growth and biosurfactant production. The growth peak was on the 8th day while the specific growth rate ranged insignificantly (P < 0.05) between 0.46 and 0.48 day⁻¹. Interestingly, biosurfactant was detected on the 2nd day when growth was almost inexistent, with maximal production obtained at stationary/death phase of growth. The partially-purified biosurfactants exhibited antimicrobial activities by completely inhibiting the growth of clinical strains of Escherichia coli and Staphylococcus aureus at all concentrations tested. Although C. albicans appeared to be a better diesel-utilizer and biosurfactant-producer (E₂₄ = 64.2%), the potency of its surfactant was smaller than that of S. cerevisiae. These strains represent a new class of biosurfactant producers that have potential for use in a variety of biotechnological and industrial processes particularly in the pharmaceutical industry.     

Bench-Scale Production of Biosurfactants and their Potential in Ex-Situ MEOR Application

The fermentative production of biosurfactants by five Bacillus strains in a bench-scale bioreactor and evaluation of biosurfactant-based enhanced oil recovery using sand pack columns were investigated. Adjusting the initial dissolved oxygen to 100% saturation, without any further control and with collection of foam and recycling of biomass, gave higher biosurfactant production. The microorganisms were able to produce biosurfactants, thus reducing the surface tension and interfacial tension to 28 mN/m and 5.8–0.5 mN/m, respectively, in less than 10 hours. The crude surfactant concentration of 0.08–1.1 g/L, and critical micelle concentration (CMC) values of 19.4–39 mg/L, corresponding to the biosurfactants produced by the different Bacillus strains, were observed. The efficiency of crude biosurfactant preparation obtained from Bacillus strains for enhanced oil recovery, by sand pack column studies, revealed it to vary from 30.22–34.19% of the water flood residual oil saturation. The results are indicative of the potential of the strains for the development of ex-situ, microbial-enhanced, oil recovery processes.     

Biosurfactant production and hydrocarbon-degradation by halotolerant and thermotolerant Pseudomonas sp.

A hydrocarbon degrading and biosurfactant producing, strain DHT2, was isolated from oil-contaminated soil. The organism grew and produced biosurfactant when cultured in variety of substrates at salinities up to 6 g l⁻¹ and temperatures up to 45°C. It was capable of utilizing crude oil, fuels, alkanes and PAHs as carbon source across the wide range of temperature (30–45°C) and salinity (0–6%). Over the range evaluated, the salinity and temperature did not influence the degradation of hydrocarbon and biosurfactant productions. Isolate DHT2 was identified as Pseudomonas aeruginosa by analysis of 16S rRNA sequences (100% homology) and biochemical analysis. PCR and DNA hybridization studies revealed that enzymes involved in PAH metabolism were related to the naphthalene dioxygenase pathway. Observation of both tensio-active and emulsifying activities indicated that biosurfactants were produced by DHT2 during growth on both, water miscible and immiscible substrates, including PAH. The biosurfactants lowered the surface tension of medium from 54.9 to 30.2 dN/cm and formed a stable emulsion. The biosurfactant produced by the organism emulsified a range of hydrocarbons with hexadecane as best substrate and toluene was the poorest. These findings further indicate that the isolate could be useful for bioremediation and bio-refining application in petroleum industry.     

Importance of 3-Hydroxy Fatty Acid Composition of Lipopeptides for Biosurfactant Activity

Biosurfactant production may be an economic approach to improving oil recovery. To obtain candidates most suitable for oil recovery, 207 strains, mostly belonging to the genus Bacillus, were tested for growth and biosurfactant production in medium with 5% NaCl under aerobic and anaerobic conditions. All strains grew aerobically with 5% NaCl, and 147 strains produced a biosurfactant. Thirty-five strains grew anaerobically with 5% NaCl, and two produced a biosurfactant. In order to relate structural differences to activity, eight lipopeptide biosurfactants with different specific activities produced by various Bacillus species were purified by a new protocol. The amino acid compositions of the eight lipopeptides were the same (Glu/Gln:Asp/Asn:Val:Leu, 1:1:1:4), but the fatty acid compositions differed. Multiple regression analysis showed that the specific biosurfactant activity depended on the ratios of both iso to normal even-numbered fatty acids and anteiso to iso odd-numbered fatty acids. A multiple regression model accurately predicted the specific biosurfactant activities of four newly purified biosurfactants (r² = 0.91). The fatty acid composition of the biosurfactant produced by Bacillus subtilis subsp. subtilis strain T89-42 was altered by the addition of branched-chain amino acids to the growth medium. The specific activities of biosurfactants produced in cultures with different amino acid additions were accurately predicted by the multiple regression model derived from the fatty acid compositions (r² = 0.95). Our work shows that many strains of Bacillus mojavensis and Bacillus subtilis produce biosurfactants and that the fatty acid composition is important for biosurfactant activity.     

Biosurfactant production by a new Pseudomonas putida strain

Observation of both tensio-active and emulsifying activities indicated that biosurfactants were produced by the newly isolated and promising strain Pseudomonas putida 21BN. The biosurfactants were identified as rhamnolipids, the amphiphilic surface-active glycolipids usually secreted by Pseudomonas spp. Their production was observed when the strain was grown on soluble substrates, such as glucose or on poorly soluble substrates, such as hexadecane, reaching values of 1.2 g l(-1). When grown on hexadecane as the sole carbon source the biosurfactant lowered the surface tension of the medium to 29 mN m(-1) and formed stable and compact emulsions with emulsifying activity of 69%.     

Biosurfactants from thermophilic dairy streptococci and their potential role in the fouling control of heat exchanger plates

Recent work on biosurfactant release by thermophilic dairy streptococci is reviewed. There is a suggestion thatStreptococcus thermophilus isolates may release biosurfactants that stimulate detachment of already-adhering cells and leave an anti-adhesive coating on a substratum. A previously published rapid screening method is described for the identification of biosurfactant-releasing microorganisms, and growth medium supplements to enhance biosurfactant release by thermophilic dairy streptococci are reported. New experimental work described includes the isolation and purification of biosurfactants from dairy isolates by thin layer chromatography. Many compounds isolated were extremely surface-active and reduced the water surface tension to values around 30 mJ m^–2 at a concentration of 10 mg ml^–1. Most importantly, the thin layer chromatograms of various isolates resembled each other, and an adsorbed purified compound from one isolate retarded the deposition to glass of another isolate by a factor of two. Provided our findings implicate that these biosurfactants could also be adsorbed to heat exchanger plates in pasteurizers and thereby retard colonization by thermophilic streptococci, these compounds may have major economic implications. Further work is required, however.     

Effect of surfactants on pyrene degradation by Pseudomonas fluorescens 29L

The effect of surfactants on pyrene degradation in Pseudomonas fluorescens 29L was investigated. This strain produced 30.1 μM of rhamnolipid equivalents (RE) of biosurfactants on 50 mg of pyrene per liter of medium. The production of biosurfactants was significantly correlated with the water solubility (S _w) of the substrate and the growth rate on it. When chrysene, with a S _w of 2.8 × 10⁻³ mg per liter of water, was the carbon source, 13.1 μM of RE of biosurfactants were produced compared to 10.3 μM of RE of biosurfactants on acenaphthene with a S _w of 1.9 mg per liter of water. No biosurfactants were produced on salicylic acid, catechol, and citrate. All of the strain 29L mutants which grew on pyrene produced biosurfactants while among the mutants which grew on naphthalene, only 88.4% produced biosurfactants. The rhamnolipid mixture, JBR425, inhibited the growth of Strain 29L wild type (WT) and all of its mutants on pyrene. However, these mutants were able to grow in the presence of pyrene when the growth medium was supplemented with 10⁻⁶ mg of emulsan per milliliter of medium. This study implies biosurfactants are produced by Strain 29L as a physiological response to the hydrophobicity of pyrene. The combined use of indigenous biosurfactants and the added biosurfactant, emulsan, is a biotechnology to enhance pyrene degradation by Pseudomonas fluorescens 29L.     

Isolation and characterization of a biosurfactant‐producing Fusarium sp. BS‐8 from oil contaminated soil

This study reports characterization of a biosurfactant‐producing fungal isolate from oil contaminated soil of Missa Keswal oil field, Pakistan. It was identified as Fusarium sp. BS‐8 on the basis of macroscopic and microscopic morphology, and 18S rDNA gene sequence homology. The biosurfactant‐producing capability of the fungal isolates was screened using oil displacement activity, emulsification index assay, and surface tension (SFT) measurement. The optimization of operational parameters and culture conditions resulted in maximum biosurfactant production using 9% (v/v) inoculum at 30°C, pH 7.0, using sucrose and yeast extract, as carbon and nitrogen sources, respectively. A C:N ratio of 0.9:0.1 (w/w) was found to be optimum for growth and biosurfactant production. At optimal conditions, it attained lowest SFT (i.e., 32 mN m^?1) with a critical micelle concentration of ≥ 1.2 mg mL^?1. During 5 L shake flask fermentation experiments, the biosurfactant productivity was 1.21 g L^?1 pure biosurfactant having significant emulsifying index (E₂₄, 70%) and oil‐displacing activity (16 mm). Thin layer chromatography and Fourier transform infrared spectrometric analyses indicated a lipopeptide type of the biosurfactant. The Fusarium sp. BS‐8 has substantial potential of biosurfactant production, yet it needs to be fully characterized with possibility of relatively new class of biosurfactants. © 2014 American Institute of Chemical Engineers Biotechnol. Prog., 30:1065–1075, 2014     

Production and characterization of a group of bioemulsifiers from the marine Bacillus velezensis strain H3

Marine microbes are a rich source of bioactive compounds, such as drugs, enzymes, and biosurfactants. To explore the bioactive compounds from our marine natural product library, an oil emulsification assay was applied to discover biosurfactants and bioemulsifiers. A spore-forming bacterial strain from sea mud was found to produce bioemulsifiers with good biosurfactant activity and a broad spectrum of antimicrobial properties. It was identified as Bacillus velezensis H3 using genomic and phenotypic data analysis. This strain was able to produce biosurfactants with an optimum emulsification activity at pH 6.0 and 2% NaCl by using starch as the carbon source and ammonium sulfate as the nitrogen source. The emulsification-guided isolation and purification procedure led to the discovery of the biosurfactant components, which were mainly composed of nC₁₄-surfactin and anteisoC₁₅-surfactin as determined by NMR and MS spectra. These compounds can reduce the surface tension of phosphate-buffered saline (PBS) from 71.8 to 24.8 mN/m. The critical micelle concentrations (CMCs) of C₁₄-surfactin and C₁₅-surfactin in 0.1 M PBS (pH 8.0) were determined to be 3.06?×?10^-5 and 2.03?×?10^-5?mol/L, respectively. The surface tension values at CMCs for C₁₄-surfactin and C₁₅-surfactin were 25.7 and 27.0 mM/m, respectively. In addition, the H3 biosurfactant exhibited antimicrobial activities against Staphyloccocus aureus, Mycobacterium, Klebsiella peneumoniae, Pseudomonas aeruginosa, and Candida albicans. Thus B. velezensis H3 is an alternative surfactin producer with potential application as an industrial strain for the lipopeptide production.     

Application of Biosurfactants Produced by Pseudomonas aeruginosa SP4 for Bioremediation of Soils Contaminated by Pyrene

Biosurfactants are considered to facilitate PAHs dissolution in soil slurries for bioremediation applications. In this work, the carbon and nitrogen sources, pH, C/N ratio, and salinity, were considered for optimization of biosurfactant production by Pseudomonas aeruginosa SP4 isolate to enhance pyrene removal from the contaminated soil. Analysis of ANOVA indicated that the carbon source was the most effective factor, followed by pH, nitrogen source, C/N ratio, and salinity. Taguchi experimental design proposed the optimum operating conditions of olive oil, NH₄NO₃, C/N ratio of 5, salinity of 0.5%, and pH 7. Applying the conditions determined by Taguchi design led to a production yield of 452 mg L^?1 (13% improvement) at the optimum conditions. The main characteristics of produced biosurfactant included the critical micelle concentration (CMC) of 60 mg L^?1 and liquid medium surface tension of 29.5 mN m^?1. Produced biosurfactant was used for bioremediation of soil artificially contaminated with 500 mg kg^?1 of pyrene. Following the addition of 250 mg L^?1 biosurfactant, the pyrene removal of 84.6% was obtained compared to 59.8% for control sample without any surfactant.     

Biosurfactant production by thermophilic dairy streptococci

Biosurfactant production of eight Streptococcus thermophilus strains, isolated from heat exchanger plates in the downstream side of the regenerator section of pasteurizers in the dairy industry has been measured using axisymmetric drop shape analysis by profile (ADSA-P). Strains were grown in M17 broth with either lactose, saccharose or glucose added. After harvesting, cells were suspended in water or in 10 mm potassium phosphate buffer, pH 7.0, and suspension droplets were put on a piece of FEP-Teflon. Changes in droplet profile were analysed by ADSA-P to yield the surface tension decrease due to biosurfactant production as a function of time. Surface tension decreases larger than 8 mJ·m^–2 were taken as indicative of biosurfactant production. Only five strains produced biosurfactants in water, solely when saccharose was added to the growth medium. In buffer, all strains produced biosurfactants and production was generally greater than in water. Also, most strains suspended in buffer produced maximally when saccharose was added to the growth medium, whereas one strain produced maximally in buffer upon the addition of glucose. Four strains suspended in buffer produced biosurfactants when glucose was added and only two strains when lactose was added. The possible role of these biosurfactants as anti-adhesives in the dairy industry and for the survival of these strains in natural systems is discussed.Correspondence to: H. J. Busscher     

Diesel Biodegradation Capacities and Biosurfactant Production in Saline-Alkaline Conditions by Delftia sp NL1, Isolated from an Algerian Oilfield

Abstract

In this study, a diesel oil-degrading bacterium was isolated from an oilfield water injection (water-bearing formations, 1,205?m depth) in Algeria. The bacterial strain, designated NL1, was cultivated on diesel oil as sole carbon and energy sources. Molecular analyses of the 16S rRNA gene sequence (KY397882) placed NL1 strain closely related to distinct cultivated species of the Delftia genus. Optimal diesel oil biodegradation by Delftia sp NL1 strain occurred at pH 11, 40?°C, 2?M NaCl and initial hydrocarbon concentration of 5% (v/v) as sole carbon source. GC-MS analyses evidenced that strain Delftia sp NL1 was able to degrade more than 66.76% of diesel oil within only 7?days. On the other hand, and in the same conditions, biosurfactant production by Delftia sp NL1 was also evaluated evidencing high emulsifying capacity (E₂₄ = 81%), ability to lower the surface tension of growing media (with the value of 25.7?mN m^?1), and production of glycolipids (8.7?g L^?1) as biosurfactants. This research presents indigenous strain Delftia sp NL1 for diesel degradation and synthesis of biosurfactant in extreme conditions. In this sense, strain NL1 is a good candidate for possible in situ oil recovery and in wastewater treatment in refineries and oil terminals in petroleum industry.     

Production and properties of a biosurfactant synthesized byArthrobacter protophormiae — an antarctic strain

This study reports the production of biosurfactant by a psychrophilic strain ofArthrobacter protophormiae during growth on an immiscible carbon source, w-hexadecane. The biosurfactant reduces the surface tension of the medium from 68.0 mN/m to 30.60 mN/m and exhibits good emulsification activity. The strain could grow and produce biosurfactant in the presence of high NaCl concentrations (10.0 to 100.0 g/1). Although the biosurfactant was isolated by growing the organism under psychrophilic conditions (10‡C) it exhibited stable activity over a wide range of temperature (30‡C to 100‡C). It retained its surface-active properties at p^H2 to 12. The biosurfactant was effective in recovering up to 90% of residual oil from an oil saturated sandpack column, indicating its potential value in enhanced oil recovery.     

Bacterial biosurfactant increases ex situ biodiesel bioremediation in clayey soil

The contamination of soils by oily compounds has several environmental impacts, which can be reversed through bioremediation, using biosurfactants as auxiliaries in the biodegradation process. In this study, we aimed to perform ex situ bioremediation of biodiesel-contaminated soil using biosurfactants produced by Bacillus methylotrophicus. A crude biosurfactant was produced in a whey-based culture medium supplemented with nutrients and was later added to biodiesel-contaminated clayey soil. The produced lipopeptide biosurfactant could reduce the surface tension of the fermentation broth to 30.2 mN/m. An increase in the microbial population was observed in the contaminated soil; this finding can be corroborated by the finding of increased CO₂ release over days of bioremediation. Compared with natural attenuation, the addition of a lower concentration of the biosurfactant (0.5% w/w in relation to the mass of diesel oil) to the soil increased biodiesel removal by about 16% after 90 days. The added biosurfactant did not affect the retention of the contaminant in the soil, which is an important factor to be considered when applying in situ bioremediation technologies.

     

Enhanced Removal of Lead from Soil Using Biosurfactant Derived from Edible Oils

ABSTRACT

Lead contamination in soil due to anthropogenic activities has amplified and therefore, remediation is of prime significance due to its nonbiodegradability and toxicity effects. This study focuses on lead removal from the soil collected from a rifle range using biosurfactants produced from native microorganisms and edible oils. Native microorganisms in contaminated soil served as a source for biosurfactant production aided by edible vegetable oils such as palm oil and gingelly oil. Preliminary isolation and characterization studies indicated the presence of Pseudomonas aeruginosa that produced biosurfactant and removed lead simultaneously. Batch adsorption experiments showed 96%–99.6% of lead adsorption following Langmuir isotherm model. Lead desorption of 23.6% occurred without biosurfactant. Whereas in the presence of biosurfactants, enhanced desorption of 62.3% was observed. Of both palm oil and gingelly oil derived biosurfactants, the former reached a lead removal efficiency of 93.6% indicating the feasibility and effectiveness of the biosurfactants for contaminated site remediation.     

Production of sophorolipid biosurfactant by Pichia anomala

Biosurfactant production by Pichia anomala PY1, a thermotorelant strain isolated from fermented food, was examined as grown in media containing various carbon and nitrogen sources. The optimal conditions for biosurfactant production included 4% soybean oil as carbon source at pH 5.5 at 30 degrees C for 7 d. Under these conditions, the surface tension of the medium decreased to 28 mN/m with oil displacement measured at 69.43 cm(2). Comparative studies of biosurfactant production in media containing glucose or soybean oil were performed. The biosurfactants obtained were isolated and purified by chromatographic methods. The molecular weights of samples were further investigated by mass spectrometry. In medium containing glucose, biosurfactants of molecular weights of 675, 691, and 707 were obtained, while those isolated from medium containing soybean oil were of molecular weights of 658, 675, and 691. These results reveal that sophorolipid compounds containing fatty acids of C20 and C18:1 were produced from both media.