Electrospun composite scaffolds containing poly(octanediol-co-citrate) for cardiac tissue engineering

A biocompatible and elastomeric nanofibrous scaffold is electrospun from a blend of poly(1,8-octanediol-co-citrate) [POC] and poly(L-lactic acid) -co-poly-(3-caprolactone) [PLCL] for application as a bioengineered patch for cardiac tissue engineering. The characterization of the scaffolds was carried out by Fourier transform infra red spectroscopy, scanning electron microscopy (SEM), and tensile measurement. The mechanical properties of the scaffolds are studied with regard to the percentage of POC incorporated with PLCL and the results of the study showed that the mechanical property and degradation behavior of the composites can be tuned with respect to the concentration of POC blended with PLCL. The composite scaffolds with POC: PLCL weight ratio of 40:60 [POC/PLCL4060] was found to have a tensile strength of 1.04 ± 0.11 MPa and Young's Modulus of 0.51 ± 0.10 MPa, comparable to the native cardiac tissue. The proliferation of cardiac myoblast cells on the electrospun POC/PLCL scaffolds was found to increase from Days 2 to 8, with the increasing concentration of POC in the composite. The morphology and cytoskeletal observation of the cells also demonstrated the biocompatibility of the POC containing scaffolds. Electrospun POC/PLCL4060 nanofibers are promising elastomeric substrates that might provide the necessary mechanical cues to cardiac muscle cells for regeneration of the heart.     

Formation of poly(epsilon-caprolactone) scaffolds loaded with small molecules by integrated processes

Cell stimulation by bioactive molecules has become an important tool in tissue engineering. The homogeneous incorporation of such molecules within the bulk of a polymer-based scaffold compared to surface coating is considered advantageous for most applications and minimizes a burst effect. An efficient way of bulk loading is the incorporation of these molecules during the scaffold formation process. In this paper, two different integrated processes for the preparation of scaffolds from poly(epsilon-caprolactone) (PCL) loaded with a small molecule are investigated. Both formation and loading of the scaffold is carried out in a single-step process. Sudan Red G was selected as a model compound for lipophilic small molecules. A freeze drying and pressure quench (PQ) formation process was selected, and the influence of the small molecule on the formation processes and on the morphology of the obtained scaffold was evaluated and compared. It could be shown for both processes that the formation of loaded scaffolds is possible, and that the small molecule has a very high impact on the foam morphology. In case of the freeze-drying (FD) method, only a load of 1 wt% Sudan Red G was incorporated within the bulk and showed no influence on the foam morphology. In the case of PQ foaming, an incorporation of 43 wt% Sudan Red G was achieved (although tiny crystal needles of the small molecule were found on the surface) and a strong effect on the foam morphology was found. This paper presents an efficient method of incorporating small molecules by integrated processes.     

Electrospun sodium alginate/poly(ethylene oxide) core-shell nanofibers scaffolds potential for tissue engineering applications

Core-shell structure nanofibers of sodium alginate/poly(ethylene oxide) were prepared via electrospinning their dispersions in water solution. The core-shell structure morphology of the obtained nanofibers was viewed under scanning electron microscope (SEM) and transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS) analysis was used to further quantify the chemical composition of the core-shell composite SA/PEO nanofibers surface in detail. Furthermore, one-step cross-linking method through being immersed in CaCl₂ solution was investigated to improve the anti-water property of the electrospun nanofibers mats in order to facilitate their practical applications as tissue engineering scaffolds, and the changes of the structural of nanofibers before and after cross-linking was characterized by Fourier transform infrared (FT-IR). Indirect cytotoxicity assessment indicated that SA/PEO nanofibers membrane was nontoxic to the fibroblasts cells, and cell culture suggested that SA/PEO nanofibers tended to promote fibroblasts cells attachment and proliferation. It was assumed that the nanofibers membrane of electrospun SA/PEO could be used for tissue engineering scaffolds.     

Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

Anaerobic biodegradation of aliphatic polyesters: poly(3-hydroxybutyrate-co-3-hydroxyoctanoate) and poly(epsilon-caprolactone)

Poly(3-hydroxybutyrate-co-3-hydroxyoctanoate), PHBO, represents a class of PHA copolymers that contain both short-chain-length and medium-chain-length repeat units. Radiolabeled and cold PHBO, containing 90 mol % 3-hydroxybutyrate and 10 mol % 3-hydroxyoctanoate were chemically synthesized using a new difunctional alkoxyzinc initiator. (14)C-PHBO was incubated with samples of anaerobic digester sludge, septage, freshwater sediment, and marine sediment under conditions resembling those in situ. In addition, it was incubated in laboratory-scale landfill reactors. (14)C-PCL (poly-epsilon-caprolactone) was incubated with anaerobic digester sludge and in landfill reactors. Biodegradation was determined by measuring generation of (14)CO(2) and (14)CH(4) resulting from mineralization of the radiolabeled polymers. PHBO was extensively mineralized in digester sludge, septage sediments, and the landfill reactors, with half-lives less than 30 days. PCL was not significantly mineralized in digester sludge over 122 days. In the landfill reactors, PCL mineralization was slow and was preceded by a long lag period (>200 days), suggesting that PCL mineralization is limited by its rate of hydrolysis. The results indicate that PHBO is practically biodegradable in the major anaerobic habitats that it may enter. In contrast, anaerobic biodegradation of PCL is less ubiquitous and much slower.     

Degradation behavior of poly(epsilon-caprolactone)-b-poly(ethylene glycol)-b-poly(epsilon-caprolactone) micelles in aqueous solution

Poly(epsilon-caprolactone)-b-poly(ethylene glycol)-b-poly(epsilon-caprolactone) triblock copolymers were synthesized by the ring-opening polymerization of epsilon-caprolactone in the presence of hydroxyl-terminated poly(ethylene glycol) with different molecular weights, using stannous octoate catalyst. Micelles prepared by the precipitation method with these triblock copolymers exhibit a core-shell structure. The degradation behaviors of these core-shell micelles in aqueous solution were investigated by FT-IR, 1H NMR, GPC, DLS, TEM, and AFM. It was found that the degradation behavior of micelles in aqueous solution was quite different from that of bulk materials. The size of the micelles increased in the initial degradation stages and decreased gradually when the degradation period was extended. The caprolactone/ethylene oxide (CL/EO) ratio in micelles measured by NMR also shows an increase at the initial degradation stage and a decrease at later stages. The morphology of these micelles became more and more irregular during the degradation period. We explain the observed behavior by a two-stage degradation mechanism with interfacial erosion between the cores and the shells followed by core erosion.     

Synthesis and characterization of star poly(epsilon-caprolactone)-b-poly(ethylene glycol) and poly(L-lactide)-b-poly(ethylene glycol) copolymers: evaluation as drug delivery carriers

Two types of 32 arm star polymers incorporating amphiphilic block copolymer arms have been synthesized and characterized. The first type, stPCL-PEG 32, is composed of a polyamidoamine (PAMAM) dendrimer as the core with radiating arms having poly(epsilon-caprolactone) (PCL) as an inner lipophilic block in the arm and poly(ethylene glycol) (PEG) as an outer hydrophilic block. The second type, stPLA-PEG 32, is similar but with poly(L-lactide) (PLA) as the inner lipophilic block. Characterization with SEC, (1)H NMR, FTIR, and DSC confirmed the structure of the polymers. Micelle formation by both star copolymers was studied by fluorescence spectroscopy. The stPCL-PEG 32 polymer exhibited unimolecular micelle behavior. It was capable of solubilizing hydrophobic molecules, such as pyrene, in aqueous solution, while not displaying a critical micelle concentration. In contrast, the association behavior of stPLA-PEG 32 in aqueous solution was characterized by an apparent critical micelle concentration of ca. 0.01 mg/mL. The hydrophobic anticancer drug etoposide can be encapsulated in the micelles formed from both polymers. Overall, the stPCL-PEG 32 polymer exhibited a higher etoposide loading capacity (up to 7.8 w/w % versus 4.3 w/w % for stPLA-PEG 32) as well as facile release kinetics and is more suitable as a potential drug delivery carrier.     

Addition of biological functionality to poly(epsilon-caprolactone) films

Biodegradable polyesters such as poly(epsilon-caprolactone) (PCL) have a number of biomedical applications; however, their usage is often limited by a lack of biological functionality. In this paper, a PCL-based polymer containing pendent groups activated by 4-nitrophenyl chloroformate (NPC) and reactive toward primary amines has been cast into thin films. The reactivity of the films toward poly(l-lysine) and the cell adhesion peptide, GRGDS, was assessed, and their cell adhesive capabilities were characterized. ATR-FTIR analysis found that NPC functional groups were present on the surface of the cast film, and the synthesis, conjugation, and visualization of a fluorescent molecule on these films further demonstrated the success of this functionalization methodology. The immersion of these films into a solution of either poly(l-lysine) (PLL) or GRGDS in PBS (pH 7.4) and subsequent 3T3 fibroblast adhesion studies demonstrated significant improvement in cell adhesion and spreading over films cast from unmodified PCL. This investigation has shown that this novel NPC-containing polymer can be utilized in many applications where increased cellular adhesion is required, or the coupling of specific molecules to polymer surfaces is of interest.     

Grafting of cellulose fibers with poly(epsilon-caprolactone) and poly(L-lactic acid) via ring-opening polymerization

In this study, ring-opening polymerization (ROP) of epsilon-caprolactone (epsilon-CL) and L-lactide (L-LA) has been performed from cellulose fibers. The hydroxyl groups on cellulose act as initiators in the polymerization, and the polymers are covalently bonded to the cellulose fiber. As an attempt to introduce more available hydroxyl groups on the surface, and thereby obtain higher grafting efficiency in the ROP of epsilon-CL and L-LA, unmodified paper was modified with xyloglucan-bis(methylol)-2-methylpropanamide (XG-bis-MPA) and 2,2-bis(methylol)propionic acid (bis-MPA), respectively. The grafted substrates were characterized via Fourier transform infrared spectroscopy (FTIR), contact angle measurement, atomic force microscopy, and enzymatic degradation. The results showed a successful grafting of poly(epsilon-caprolactone) (PCL) and poly(L-lactic acid) (PLLA) from the cellulose fiber surfaces. Furthermore, the results showed an improved grafting efficiency after activation of the cellulose surface with bis-MPA, and showed that the amount of grafted polymer could be controlled by the ratio of added free initiator to monomer.     

Mannosylated poly(ethylene oxide)-b-poly(epsilon-caprolactone) diblock copolymers: synthesis, characterization, and interaction with a bacterial lectin

A novel bioeliminable amphiphilic poly(ethylene oxide)-b-poly(epsilon-caprolactone) (PEO-b-PCL) diblock copolymer end-capped by a mannose residue was synthesized by sequential controlled polymerization of ethylene oxide and epsilon-caprolactone, followed by the coupling of a reactive mannose derivative to the PEO chain end. The anionic polymerization of ethylene oxide was first initiated by potassium 2-dimethylaminoethanolate. The ring-opening polymerization of epsilon-caprolactone was then initiated by the omega-hydroxy end-group of PEO previously converted into an Al alkoxide. Finally, the saccharidic end-group was attached by quaternization of the tertiary amine alpha-end-group of the PEO-b-PCL with a brominated mannose derivative. The copolymer was fully characterized in terms of chemical composition and purity by high-resolution NMR spectroscopy and size exclusion chromatography. Furthermore, measurements with a pendant drop tensiometer showed that both the mannosylated copolymer and the non-mannosylated counterpart significantly decreased the dichloromethane/water interfacial tension. Moreover, these amphiphilic copolymers formed monodisperse spherical micelles in water with an average diameter of approximately 11 nm as measured by dynamic light scattering and cryo-transmission electron microscopy. The availability of mannose as a specific recognition site at the surface of the micelles was proved by isothermal titration microcalorimetry (ITC), using the BclA lectin (from Burkholderia cenocepacia), which interacts selectively with alpha-D-mannopyranoside derivatives. The thermodynamic parameters of the lectin/mannose interaction were extracted from the ITC data. These colloidal systems have great potential for drug targeting and vaccine delivery systems.     

A convenient method for the synthesis of amine-terminated poly(ethylene oxide) and poly(epsilon-caprolactone)

A convenient synthetic route to prepare amine-terminated poly(ethylene oxide) (PEO) and poly(epsilon-caprolactone) (PCL) was described. The strategy involved two-step reactions, the condensation of hydroxyl-terminated PEO and PCL with N-benzyloxycarbonyl amino acid followed by the catalytic hydrogenation under mild conditions. NMR and GPC measurements indicated that the reactions proceeded nearly quantitatively. Amine-terminated PEO thus prepared was used to initiate the polymerization of alpha-(N(epsilon)-benzyloxycarbonyl-L-lysine) N-carboxy anhydride [lys(Z)-NCA], and the results confirmed that the reactivity of the amino group was high.     

Electrospun PLLA nanofiber scaffolds and their use in combination with BMP-2 for reconstruction of bone defects

Introduction

Adequate migration and differentiation of mesenchymal stem cells is essential for regeneration of large bone defects. To achieve this, modern graft materials are becoming increasingly important. Among them, electrospun nanofiber scaffolds are a promising approach, because of their high physical porosity and potential to mimic the extracellular matrix (ECM).

Materials and Methods

The objective of the present study was to examine the impact of electrospun PLLA nanofiber scaffolds on bone formation in vivo, using a critical size rat calvarial defect model. In addition we analyzed whether direct incorporation of bone morphogenetic protein 2 (BMP-2) into nanofibers could enhance the osteoinductivity of the scaffolds. Two critical size calvarial defects (5 mm) were created in the parietal bones of adult male Sprague-Dawley rats. Defects were either (1) left unfilled, or treated with (2) bovine spongiosa, (3) PLLA scaffolds alone or (4) PLLA/BMP-2 scaffolds. Cranial CT-scans were taken at fixed intervals in vivo. Specimens obtained after euthanasia were processed for histology, histomorphometry and immunostaining (Osteocalcin, BMP-2 and Smad5).

Results

PLLA scaffolds were well colonized with cells after implantation, but only showed marginal ossification. PLLA/BMP-2 scaffolds showed much better bone regeneration and several ossification foci were observed throughout the defect. PLLA/BMP-2 scaffolds also stimulated significantly faster bone regeneration during the first eight weeks compared to bovine spongiosa. However, no significant differences between these two scaffolds could be observed after twelve weeks. Expression of osteogenic marker proteins in PLLA/BMP-2 scaffolds continuously increased throughout the observation period. After twelve weeks osteocalcin, BMP-2 and Smad5 were all significantly higher in the PLLA/BMP-2 group than in all other groups.

Conclusion

Electrospun PLLA nanofibers facilitate colonization of bone defects, while their use in combination with BMP-2 also increases bone regeneration in vivo and thus combines osteoconductivity of the scaffold with the ability to maintain an adequate osteogenic stimulus.     

Supramolecular Polypseudorotaxanes composed of star-shaped porphyrin-cored poly(epsilon-caprolactone) and alpha-cyclodextrin

Star-shaped porphyrin-cored poly(epsilon-caprolactone) (SPPCL) was synthesized using a tetrahydroxyethyl-terminated porphyrin as a core initiator and stannous octoate as a catalyst in bulk at 120 degrees C. The molecular weight of as-synthesized polymer could be adjusted linearly by controlling the molar ratio of epsilon-caprolactone to porphyrin core initiator, and the molecular weight distribution was reasonably narrow. Supramolecular polypseudorotaxanes were prepared by inclusion complexation of SPPCL with alpha-cyclodextrin (alpha-CD) and thoroughly characterized by means of FT-IR, 1H NMR, 13C CP/MAS NMR, DSC, TGA, and WAXD. The results demonstrated that the porphyrin-cored polypseudorotaxanes formed through alpha-CD molecules threading onto the branch chains of star-shaped SPPCL polymers, and they had a channel-type crystalline structure. Meanwhile, the original crystallization of SPPCL polymers within the polypseudorotaxanes was completely suppressed in the alpha-CD cavities. Moreover, inclusion complexation between SPPCL and alpha-CD enhanced the thermal stability of both the guest SPPCL polymers and the host alpha-CD. Furthermore, both the SPPCL polymers and the polypseudorotaxanes showed similar fluorescent and UV-vis spectra compared with porphyrin core initiator. Consequently, this will not only provide potentially porphyrin-cored poly(epsilon-caprolactone) and its polypseudorotaxanes for photodynamic therapy but also improve the compatibility between poly(epsilon-caprolactone) and peptide drugs for drug delivery.     

Comparison of acellular and cellular bioactivity of poly 3-hydroxybutyrate/hydroxyapatite nanocomposite and poly 3-hydroxybutyrate scaffolds

Nanocomposites have recently been identified as a useful scaffolding material in tissue engineering applications. Poly (3-hydroxybutyrate)/hydroxyapatite nanoparticles (P3HB)/(nHA) porous scaffolds were successfully fabricated through a solvent casting and particulate leaching technique. P3HB/nHA and P3HB scaffolds were prepared by the same technique for comparison. The structure of the nanocomposite and P3HB scaffolds was observed by SEM. The Energy Disperssive X-ray Analysis (EDXA, map of Ca) results indicated that HA nanoparticles were homogeneously dispersed in the P3HB matrix. X-ray diffraction (XRD) analysis showed that P3HB and HA coexist in the nanocomposite. Transmission electron microscopy (TEM) images also showed that the particle size of HA was 30 ～ 40 nm. The porosity of the scaffolds was 84%, and macropores and micropores coexisted and interconnected throughout the scaffolds. Acellular bioactivity experiments showed that more HA crystals formed on the surface of the nanocomposite scaffold than on the P3HB scaffold after 4 weeks immersion in Simulated Body Fluid (SBF). Cell culture experiments demonstrated that the P3HB/nHA nanocomposite scaffold had a better tendency of proliferation and Alkaline Phosphatase (ALP) activity to MG 63 cells than the pure P3HB scaffold. It was found that nHA addition can improve acellular and cellular bioactivity of the P3HB scaffold.     

Variable temperature FTIR study of poly(ethylene-co-vinyl alcohol)-graft-poly(epsilon-caprolactone)

A recently developed technique, i.e., two-dimensional infrared (2D IR) correlation spectroscopy, is used to study the thermal behavior of poly(ethylene-co-vinyl alcohol)-graft-poly(epsilon-caprolactone), a new synthesized highly grafted copolymer. The use of the 2D IR approach to analyze temperature-dependent spectra collected in situ during the temperature elevation process effectively enhanced the spectral resolution and revealed details on the hydrogen bonding and conformational change which are not easily detected in the traditional one-dimensional spectra. The sequence of the spectral changes of different OH and CH(2) fundamental vibrations during heating the polymer was inferred from the signs of the asynchronous peaks. Evidence that the conformational changes of the methylene groups precede the loosening of hydrogen bonds is provided.     

FT-IR imaging spectroscopy of phase separation in blends of poly(3-hydroxybutyrate) with poly(L-lactic acid) and poly(epsilon-caprolactone)

The detection of phase separation and identification of miscibility in biopolymer blends is an important aspect for the improvement of their physical properties. In this article, the phase separation in blends of poly(3-hydroxybutyrate) (PHB) with poly(L-lactic acid) (PLA) and poly(epsilon-caprolactone) (PCL), respectively, has been studied as a function of the blend composition by FT-IR imaging spectroscopy. For both polymer blend systems, a miscibility gap has been found around the 50:50% (w/w) composition of the two components. Furthermore, the separating phases have been identified as blends of the two polymer components and their compositions could be determined from calibrations based on the spectra of the blends in the compositional range of miscibility. The data derived from FT-IR spectroscopic imaging were corroborated by additional DSC analyses and mechanical stress-strain measurements of polymer blend films, which exhibited a characteristic fracture behavior as a function of PHB composition.     

Cellular internalization of poly(ethylene oxide)-b-poly(epsilon-caprolactone) diblock copolymer micelles

Poly(ethylene oxide)-b-poly(epsilon-caprolactone) (PEO-b-PCL) block copolymers self-assemble into micelles in aqueous solution. We have examined whether these micelles can internalize into P19 cells in vitro. Fluorescently labeled PEO(45)-b-PCL(23) block copolymer was prepared by conjugating a tetramethylrhodamine molecule to the end of the hydrophobic PCL block. Dynamic light scattering (DLS) and transmission electron microscopy (TEM) studies yielded 24 +/- 2 and 25 +/- 2 nm, respectively, for the diameters of the micelles. The studies also showed that chemical labeling did not effect the morphology or size. When the rhodamine-labeled PEO(45)-b-PCL(23) block copolymer micelles were tested in vitro, time-, concentration-, and pH-dependence of the internalization process suggested that internalization proceeded by endocytosis. The results from these studies provide the first direct evidence for the internalization of PEO(45)-b-PCL(23) micelles. Future studies will utilize multiple labeling of these micelles, allowing questions to be addressed related to the fate of internalized micelles as drug carriers, the destination of the incorporated drugs or fluorescent probes released from micelles, and the identification of the subcellular localization of the whole drug-carrier system within cells, both in vitro and in vivo.     

Lipase-catalyzed biodegradation of poly(epsilon-caprolactone) blended with various polylactide-based polymers

Poly(epsilon-caprolactone) was blended with various polylactide-based polymers and processed to films by the solution casting method. Blends of 25/75, 50/50, 75/25, 90/10, and 95/5 (w/w) poly(epsilon-caprolactone)/poly(l-lactide), a 95/5 (w/w) blend of poly(epsilon-caprolactone) with a poly(d-lactide), a 50/50 (w/w) poly(l-lactide)-poly(d-lactide) mixture, and a poly(l-lactide-co-epsilon-caprolactone) copolymer were considered comparatively. The various phase-separated films were allowed to degrade in the presence of Pseudomonas lipase, biodegradation being monitored by proton nuclear magnetic resonance, size exclusion chromatography, differential scanning calorimetry, X-ray diffraction, and environmental scanning electron microscopy. The formation of separated phases during solvent evaporation and their morphologies are discussed. The introduction of poly(l-lactide) dramatically decreased the degradation rate of poly(epsilon-caprolactone)/poly(l-lactide) blends. The higher the percentage of poly(l-lactide), the slower the degradation, while the presence of cracks and increasing the lipase concentration acted in favor of the enzymatic degradation. Long-term enzymatic degradation of the various 95/5 blends was investigated over 480 h. The poly(epsilon-caprolactone) phase was enzymatically degraded by the lipase regardless of the blend type, the degradation rate depending on the nature of the co-components.     

Processing methods of ultrathin poly(epsilon-caprolactone) films for tissue engineering applications

Ultrathin poly(epsilon-caprolactone) (PCL) films were fabricated through biaxially drawn films made from three different methods, namely, spin casting, 2-roll milling, and solution casting. Biaxial drawn spin cast films yield thickness of 1.2 microm which is 9 and 12 times thinner that 2-roll mill and solvent cast films, respectively. The films fabricated were found to exhibit different drawing ratios. 2-roll mill film exhibits the highest drawing ratio of 4 x 4 while spin cast films can only draw up to a ratio of 2 x 2. The morphology of the films, studied using a polarized microscope and atomic force microscope, showed fine fibrillar networks of different thicknesses. Biaxially drawn 2-roll mill and solvent cast films showed thicker fibrils as compared to those for the spin cast films. Such a difference can be attributed to larger spherulites caused by slower cooling rates during melt pressing for both 2-roll mill and solvent cast films and smaller spherulites because of fast cooling during evaporation for spin cast films. Thermal analysis through differential scanning calorimetry revealed a slight increase in the peak-melting temperature after biaxial drawing. A drop in percentage crystallinity was also noted. The result of the water vapor transmission rate (WVTR) was found to be dependent on fabrication techniques that determine the spherulites formation. It was also found that the WVTR was inversely proportional to the thickness of the films. Tensile strength and modulus of the films showed significant improvements after biaxial stretching. By identifying the unique strengths of each individual PCL film produced via different techniques, it is possible to apply to different areas of membrane tissue engineering such as dermatology, ophthalmology, vascular graft engineering, and soft tissue regeneration.