初始底物浓度对序批式培养光合细菌产氢动力学影响

实验研究了初始底物浓度对序批式培养光合细菌生长、降解及产氢过程的影响,根据最大比生长速率实验数据拟合得到其关于初始底物浓度影响的关联式,并在建立的修正Monod模型基础上建立了光合细菌比生长速率、基质比消耗速率和比产氢速率关于底物初始浓度影响的数学模型,模型预测值与实验结果在光合细菌生长期和稳定期内得到较好吻合,反映了光合细菌生长、降解和产氢过程中受底物初始浓度限制性和抑制性影响的基本规律。分析发现光合细菌生长、降解基质和产氢过程中最适底物浓度为50 mmol/L,初始底物浓度低于或高于该浓度时,光合细菌生长、降解及产氢过程都受到限制性或抑制性影响,且抑制性影响较限制性影响效果更明显;底物比消耗速率受初始底物浓度影响较小。     

Influence of the ratio of the initial substrate concentration to biomass concentration on the performance of a sequencing batch reactor

Biomass behaviour and COD removal in a benchscale activated sludge reactor have been studied alternating anaerobic and aerobic conditions. Particular attention has been paid to the influence of the ratio of the initial substrate concentration (S ₀) to the initial biomass concentration (X ₀) on the reactor performance. Tests at very low ratios (S ₀/X ₀<2) demonstrate the existence of a threshold below which the reactor performance is seriously affected (S ₀/X ₀=0.5). Under conditions of total suppression of cell duplication, substrate maintenance requirements have also been calculated for the microbial consortium present in the activated sludges. The results obtained show that stressed biomass can survive conditions of substrate lack better than unstressed biomass.List of Symbols b h^–1 specific death rate - COD g/l chemical oxygen demand - DO g/l dissolved oxygen concentration - K _s g/l Monod saturation constant - MLSS g/l mixed liquor suspended solid concentration - P g/l phosphorus concentration - S g/l substrate concentration - S ₀ g/l initial substrate concentration - SS g/l suspended solid concentration - t h time - X g/l biomass concentration - X ₀ g/l initial biomass concentration - Y _SX g/g yield of growth on substrate - _max h^–1 maximum specific growth rate     

Quantification of the effect of substrate concentration on the conjugal transfer rate of the TOL plasmid in short-term batch mating experiments

Batch mating experiments with Pseudomonas putida PAW 1 (TOL) as a donor and Pseudomonas aeruginosa PAO 1162 as a recipient strain were performed to quantify the effect of the substrate concentration in the mating medium on the observed plasmid transfer rate coefficient. The impact of the substrate concentration in the mating medium was highly correlated with the growth history of the donor strain. When the donor strain was harvested in exponential growth phase, no impact was observed; when the donor strain was taken from the stationary phase, however, a strong impact of the substrate concentration was measured: a 10-fold reduction in the substrate concentration decreased the observed plasmid transfer rate by 55%.     

Effect of substrate loading rate of chemical wastewater on fermentative biohydrogen production in biofilm configured sequencing batch reactor

The influence of substrate loading rate on fermentative hydrogen (H2) production was studied in biofilm configured sequencing batch reactor using chemical wastewater as substrate. Reactor was operated with selectively enriched anaerobic mixed microflora at different organic loading rates (OLRs; 6.3, 7.1 and 7.9kg COD/m3 day) after adjusting the feed to a pH of 6.0 (acidophilic) to provide suitable environment for acidogenic bacterial function. Variation in H2 production rate was observed with change in OLR [specific hydrogen yield - 13.44molH2/kgCODRday (6.3kgCOD/m3day), 8.23molH2/kgCODRday (7.1kgCOD/m3 day) and 6.064molH2/kgCODR day (7.9kgCOD/m3 day)]. H2 yield showed reasonably good correlation with pH drop [6.3kgCOD/m3 day (R2 - 0.9796), 7.1kgCOD/m3 day (R2 - 0.9973), 7.9kgCOD/m3 day (R2 - 0.9908)]. Increase in OLR showed marked reduction in COD removal efficiency [22.6% - 6.3kgCOD/m3 day; 19.8% - 7.1kgCOD/m3 day and 17.2% - 7.9kgCOD/m3 day].     

A critical comparison of extant batch respirometric and substrate depletion assays for estimation of nitrification biokinetics

Estimation of nitrification biokinetics has been conducted using different batch techniques via measurement of nitrogen species or surrogates such as oxygen (respirometry). However, there are no reports that specifically compare kinetic parameters estimated from respirometry with those from direct nitrogen species measurements. In this study, we evaluated the ability of parameter estimates from isolated and optimally designed complete extant respirometric assays to describe concurrently obtained ammonia and nitrite depletion profiles. Additionally, we mapped the different parameter sets to steady-state bioreactor performance. Using multivariate analysis of variance, we found that estimates from respirometric and substrate depletion assays were predominantly statistically different at the 95% confidence level. The sensitivity of predicted stead-state nitrifying reactor performance to differences in parameter estimates was highest close to the limiting solids retention time (SRT). However, at characteristic nitrifying SRTs the predicted reactor performance using parameter estimates from respirometry and substrate depletion assays were in very close correspondence. Therefore, parameters estimated from extant respirometric assays can be used to adequately predict nitrifying reactor performance.     

Partial nitrification in a sequencing batch reactor treating acrylic fiber wastewater

A sequencing batch reactor was employed to treat the acrylic fiber wastewater. The dissolved oxygen and mixed liquor suspended solids were 2–3 and 3,500–4,000 mg/L, respectively. The results showed ammonium oxidizing bacteria (AOB) had superior growth rate at high temperature than nitrite oxidizing bacteria (NOB). Partial nitrification could be obtained with the temperature of 28 °C. When the pH value was 8.5, the nitrite-N accumulation efficiency was 82 %. The combined inhibitions of high pH and free ammonium to NOB devoted to the nitrite-N buildup. Hydraulic retention time (HRT) was a key factor in partial nitrification control, and the optimal HRT was 20 h for nitrite-N buildup in acrylic fiber wastewater treatment. The ammonium oxidation was almost complete and the transformation from nitrite to nitrate could be avoided. AOB and NOB accounted for 2.9 and 4.7 %, respectively, corresponding to the pH of 7.0. When the pH was 8.5, they were 6.7 and 0.9 %, respectively. AOB dominated nitrifying bacteria, and NOB was actually washed out from the system.     

Effect of oxygen concentration on nitrification and denitrification in single activated sludge flocs

Simultaneous nitrification and denitrification (SND) was investigated in the single aeration tank of a municipal wastewater treatment plant. Microelectrode measurements and batch experiments were performed to test for the presence of SND. Microelectrodes recorded the presence of O(2) concentration gradients in individual activated sludge flocs. When the O(2) concentration in the bulk liquid was <45 microM, anoxic zones were detected within flocs with a larger diameter (approximately 3000 microm). The O(2) penetration depth in the floc was found to be dependent on the O(2) concentration in the bulk liquid. Nitrification was restricted to the oxic zones, whereas denitrification occurred mainly in the anoxic zones. The nitrification rate of the activated sludge increased with increasing O(2) concentration in the bulk liquid, up to 40 microM, and remained constant thereafter. SND was observed in the aerated activated sludge when O(2) concentration was in the range of 10 to 35 microM.     

Analysis of factors affecting the performance of partial nitrification in a sequencing batch reactor

The objective of this study was to analyze the factors affecting the performance of partial nitrification in a sequencing batch reactor. During a 140-day long-term operation, influent pH value, dissolved oxygen (DO), and chemical oxygen demand/nitrogen (COD/N) ratio were selected as operating factors to evaluate the maintenance and recovery of nitrite accumulation. Results showed that high DO concentration (2–4 mg/L) could damage nitrite accumulation immediately. However, nitrite accumulation ratio (NAR) could be increased from 1.68?±?1.51 to 35.46?±?7.86 % when increasing the pH values from 7.5 to 8.3 due to the increased free ammonia concentration. Afterwards, stable partial nitrification and high NAR could be recovered when the reactor operated under low DO concentration (0.5–1.0 mg/L). However, it required a long time to recover the partial nitrification of the reactor when the influent COD/N ratios were altered. Fluorescence in situ hybridization analysis implied that ammonium oxidizing bacteria were completely recovered to the dominant nitrifying bacteria in the system. Meanwhile, sludge volumetric index of the reactor gradually decreased from 115.6 to 56.6 mL/g, while the mean diameter of sludge improved from74.57 to 428.8 μm by using the strategy of reducing settling time. The obtained results could provide useful information between the operational conditions and the performance of partial nitrification when treating nitrogen-rich industrial wastewater.     

Single-step nitrification models erroneously describe batch ammonia oxidation profiles when nitrite oxidation becomes rate limiting

Nitrification involves the sequential biological oxidation of reduced nitrogen species such as ammonium-nitrogen (NH(4)(+)-N) to nitrite-nitrogen (NO(2)(-)-N) and nitrate-nitrogen (NO(3)(-)-N). The adequacy of modeling NH(4)(+)-N to NO(3)(-)-N oxidation as one composite biochemical reaction was examined at different relative dynamics of NH(4)(+)-N to NO(2)(-)-N and NO(2)(-)-N to NO(3)(-)-N oxidation. NH(4)(+)-N to NO(2)(-)-N oxidation and NO(2)(-)-N to NO(3)(-)-N oxidation by a mixed nitrifying consortium were uncoupled using selective inhibitors allylthiourea and sodium azide. The kinetic parameters of NH(4)(+)-N to NO(2)(-)-N oxidation (q(max,ns) and K(S,ns)) and NO(2)(-)-N to NO(3)(-)-N oxidation (q(max,nb) and K(S,nb)) were determined by a rapid extant respirometric technique. The stoichiometric coefficients relating nitrogen removal, oxygen uptake and biomass synthesis were derived from an electron balanced equation. NH(4)(+)-N to NO(2)(-)-N oxidation was not affected by NO(2)(-)-N concentrations up to 100 mg NO(2)(-)-N L(-1). NO(2)(-)-N to NO(3)(-)-N oxidation was noncompetitively inhibited by NH(4)(+)-N but was not inhibited by NO(3)(-)-N concentrations up to 250 mg NO(3)(-)-N L(-1). When NH(4)(+)-N to NO(2)(-)-N oxidation was the sole rate-limiting step, complete NH(4)(+)-N to NO(3)(-)-N oxidation was adequately modeled as one composite process. However, when NH(4)(+)-N to NO(2)(-)-N oxidation and NO(2)(-)-N to NO(3)(-)-N oxidation were both rate limiting, the estimated lumped kinetic parameter estimates describing NH(4)(+)-N to NO(3)(-)-N oxidation were unrealistically high and correlated. These findings indicate that the use of single-step models to describe batch NH(4)(+) oxidation yields erroneous kinetic parameters when NH(4)(+)-to-NO(2)(-) oxidation is not the sole rate-limiting process throughout the assay. Under such circumstances, it is necessary to quantify NH(4)(+)-N to NO(2)(-)-N oxidation and NO(2)(-)-N to NO(3)(-)-N oxidation, independently.     

Influence of temperature and substrate concentration on bacterial growth yield in Seine River water batch cultures.

The growth of natural bacterial assemblages was monitored in 3-liter reactors under various temperature and substrate concentration conditions. The oxygen concentration was continuously monitored, and subsamples were taken at short time intervals to determine bacterial number and biomass. The rate of bacterial mortality was also determined. Bacterial growth yield was calculated as the ratio of net production (increase in biomass corrected for mortality) to gross production (net production plus oxygen consumption expressed in carbon units). Averaging 33%, the growth yield did not show any trend with temperatures in the range of 8 to 25 degrees C but increased with the concentration of dissolved organic carbon in the range of 2 to 12 mg of C.liter-1.     

Multisubstrate Michaëlis-Menten kinetics: Explicit dependence of substrate concentration on time for batch reactors

The problem of expressing the concentration of each of a set of substrates in a batch reactor as an explicit function of time in the case the multisubstrate system is described by Michaelis-Menten kinetics is tackled in dimensionless form via expansion as a Taylor series. The general analytical form for the coefficients of this expansion is obtained and estimates of the average quadratic error associated with increasing number of terms of the expansion is calculated. Considering the situation where the concentration of all substrates varies in a similar fashion, one concludes that use of four terms yields errors well within the range acceptable for predesign steps. In addition to other applications, the reasoning developed here finds applications in the statistical design and analysis of experiments aiming at the nonlinear fitting of kinetic parameters to actual data.     

Effect of phosphate buffer concentration on the batch xylitol production by Candida guilliermondii

AIMS: To evaluate the effect of phosphate buffer concentration on growth and xylitol production by Candida guilliermondii FTI 20037. METHODS AND RESULTS: Fermentations runs were carried out in batch mode employing semisynthetic medium supplemented with phosphate buffer at different concentrations (from 200 to 600 mmol l(-1)). The xylitol yield (Y(P/S)) and volumetric productivity (Q(P)) were improved when the fermentation medium was supplemented with phosphate buffer at concentration of 600 mmol l(-1). Under this condition (Y(P/S)) and (Q(P)) values were 0.75 g g(-1) and 0.66 g l(-1) h(-1), respectively, whereas in the absence of the phosphate buffer these values decreased to 0.52 g g(-1) and 0.44 g l(-1)h(-1) respectively. CONCLUSIONS: The use of phosphate buffer at 600 mmol l(-1) promoted an easier pH control during shake flasks fermentation of C. guilliermondii. In addition the xylitol yield and productivity were significantly improved in response to the supplementation of potassium phosphate in the medium. The increase in these parameters could be related to both osmotic effect and pH control. SIGNIFICANCE AND IMPACT OF THE STUDY: This approach provided a method for improving the xylitol production from semisynthetic medium by C. guilliermondii, being possible their use as a simple strategy to achieve efficient fermentation processes employing complex medium such as lignocellulosic hydrolysates.     

Influence of initial cellulose concentration on the carbon flow distribution during batch fermentation by Clostridium thermocellum ATCC 27405

The objective of this research was to understand how carbon loading influences hydrogen (H₂) synthesis and metabolic flow patterns in the thermophilic, cellulolytic bacterium, Clostridium thermocellum. C. thermocellum was cultivated in batch cultures with high (5 g L⁻¹) and low (1 g L⁻¹) initial concentrations of α-cellulose at 60°C. The growth rate of C. thermocellum was 22% lower (0.15 h⁻¹) in cultures with low-cellulose concentration compared with cultures with high-cellulose concentrations. Although substrate depletion coincided with the end of log-growth in low-cellulose cultures, the prime reason for growth arrest in high-cellulose cultures was not identified. Ethanol, acetate, and formate were the major soluble end-products with concomitant release of H₂ and CO₂ under both conditions. Lactate appeared during the late log phase in high-carbon cultures when pH dropped below 6.4 and became the major end-product in stationary phase. During the exponential phase of cell growth, significantly higher yields for H₂ and acetate (1.90 ± 0.14 and 1.11 ± 0.04 mol/mol glucose equivalent, respectively) were obtained from low-cellulose cultures compared to those from high-cellulose cultures. The maximum specific rate of H₂ production, 6.41 ± 0.13 mmol H₂/g dry cell/h, obtained during the exponential phase from low-carbon cultures was about 37% higher than that obtained from high-carbon cultures.     

The Michaelis -- Menten equation: computing substrate concentration as a function of time without restrictions on the initial conditions

We describe a novel algorithm for enzyme kinetics followingthe Michaelis-Menten equation, with the particular aim of computingthe substrate concentration as a function of time without restrictionson the initial conditions. This algorithm, named ‘tangentexponential’ was demonstrated to converge for all initialconditions when the initial substrate concentration is positive.When the data are close to the solution, a quadratic convergencewas demonstrated. Received on June 13, 1990; accepted on October 9, 1990     

The effect of a nitrification inhibitor on the concentration of nitrate in grass during growth

Summary In an experiment on clay-loam soil ammonium sulphate with or without the nitrification inhibitor 2-chloro-6-(trichloromethyl) pyridine (at 2% of the weight of N in fertilizer) or sodium nitrate were applied at 100 or 200 lb N/acre to the seedbed before sowing S22 Italian ryegrass and again after the first cut. Eighty-four days after the first dressing, all the grass given 100 lb N/acre contained similar amounts of nitrate-N; with 200 lb N/acre, grass given ammonium sulphate alone contained most nitrate-N and grass given ammonium sulphate plus inhibitor least. Forty-two days after the second dressing, all the grass given 100 lb N/acre again contained similar amounts of nitrate-N and with 200 lb N/acre, grass given sodium nitrate contained most nitrate-N and that given ammonium sulphate plus inhibitor least.     

Effects of temperature on simultaneous nitrification and denitrification via nitrite in a sequencing batch biofilm reactor

A laboratory scale experiment was described in this paper to enhance biological nitrogen removal by simultaneous nitrification and denitrification (SND) via nitrite with a sequencing batch biofilm reactor (SBBR). Under conditions of total nitrogen (TN) about 30 mg/L and pH ranged 7.15–7.62, synthetic wastewater was cyclically operated within the reactor for 110 days. Optimal operation conditions were established to obtain consistently high TN removal rate and nitrite accumulation ratio, which included an optimal temperature of 31 °C and an aeration time of 5 h under the air flow of 50 L/h. Stable nitrite accumulation could be realized under different temperatures and the nitrite accumulation ratio increased with an increase of temperature from 15 to 35 °C. The highest TN removal rate (91.9%) was at 31 °C with DO ranged 3–4 mg/L. Process control could be achieved by observing changes in DO and pH to judge the end-point of oxidation of ammonia and SND.     

Effect of bacterial density and substrate concentration on yield coefficients

Measurements were made of the yield coefficient during the aerobic metabolism of glucose by a heterogeneous bacterial mixture. Expressed in terms of carbon, the coefficient was approximately 0.48. The value did not vary with initial bacterial densities ranging from 0.4 pg to 40 micrograms of cell carbon per ml and with glucose concentrations ranging from 43 pg to 100 micrograms of carbon per ml. Under all these circumstances, about 44% of the glucose carbon was converted to CO2, and 7.4% was excreted as organic products. The significance of uncharacterized organic substrates contaminating the medium to the coefficients calculated for low glucose concentrations is discussed.