The Cardiocoil stent-artery interaction

An analytical approach for the mechanical interaction of the self-expanding Cardiocoil stent with the stenosed artery is presented. The damage factor as the contact stress at the stent-artery interface is determined. The stent is considered as an elastic helical rod having a nonlinear pressure-displacement dependence, while the artery is modeled by an elastic cylindrical shell. An influence of a moderate relative thickness of the shell is estimated. The equations for both the stent and the artery are presented in the stent-associated helical coordinates. The computational efficiency of the model enabled to carry out a parametric study of the damage factor. Comparative examinations are conducted for the stents made of the helical rods with circular and rectangular cross sections. It was found, in particular, that, under same other conditions, the damage factor for the stent with a circular cross section may be two times larger than that for a rectangular one.     

Study of the evolution of the shear stress on the restenosis after coronary angioplasty

In this article, we analyze the influence of fluid dynamics variables on the development of obstructive coronary artery disease in the medium term after percutaneous coronary intervention with stent implantation. We have analyzed a group of seven patients and the study is focused on the mid-right coronary artery. In these patients we have studied the relationship between wall shear stress and arterial wall thickness both immediately after stent implantation and six months later. The realistic three-dimensional (3D) reconstruction of the arteries is performed with the data obtained with intravascular ultrasound (IVUS) and angiography. The commercial code Fluent is used to solve the Navier-Stokes equations. Special attention is paid to the shear stress on the wall arteries and the corresponding thickness. The results show that there is a negative correlation for most of the cases between the wall shear stress and increase in wall thickness. A model is proposed to study the instability at the wall, and qualitative agreement is found.     

Modelling intravascular delivery from drug-eluting stents with biodurable coating: investigation of anisotropic vascular drug diffusivity and arterial drug distribution

In-stent restenosis occurs in coronary arteries after implantation of drug-eluting stents with non-uniform restenosis thickness distribution in the artery cross section. Knowledge of the spatio-temporal drug uptake in the arterial wall is useful for investigating restenosis growth but may often be very expensive/difficult to acquire experimentally. In this study, local delivery of a hydrophobic drug from a drug-eluting stent implanted in a coronary artery is mathematically modelled to investigate the drug release and spatio-temporal drug distribution in the arterial wall. The model integrates drug diffusion in the coating and drug diffusion with reversible binding in the arterial wall. The model is solved by the finite volume method for both high and low drug loadings relative to its solubility in the stent coating with varied isotropic–anisotropic vascular drug diffusivities. Drug release profiles in the coating are observed to depend not only on the coating drug diffusivity but also on the properties of the surrounding arterial wall. Time dependencies of the spatially averaged free- and bound-drug levels in the arterial wall on the coating and vascular drug diffusivities are discussed. Anisotropic vascular drug diffusivities result in slightly different average drug levels in the arterial wall but with very different spatial distributions. Higher circumferential vascular diffusivity results in more uniform drug loading in the upper layers and is potentially beneficial in reducing in-stent restenosis. An analytical expression is derived which can be used to determine regions in the arterial with higher free-drug concentration than bound-drug concentration.     

Effects of different stent designs on local hemodynamics in stented arteries

Following the deployment of a coronary stent and disruption of an atheromatous plaque, the deformation of the arterial wall and the presence of the stent struts create a new fluid dynamic field, which can cause an abnormal biological response. In this study 3D computational models were used to analyze the fluid dynamic disturbances induced by the placement of a stent inside a coronary artery. Stents models were first expanded against a simplified arterial plaque, with a solid mechanics analysis, and then subjected to a fluid flow simulation under pulsatile physiological conditions. Spatial and temporal distribution of arterial wall shear stress (WSS) was investigated after the expansion of stents of different designs and different strut thicknesses. Common oscillatory WSS behavior was detected in all stent models. Comparing stent and vessel wall surfaces, maximum WSS values (in the order of 1Pa) were located on the stent surface area. WSS spatial distribution on the vascular wall surface showed decreasing values from the center of the vessel wall portion delimited by the stent struts to the wall regions close to the struts. The hemodynamic effects induced by two different thickness values for the same stent design were investigated, too, and a reduced extension of low WSS region (<0.5Pa) was observed for the model with a thicker strut.     

Relative contribution of wall shear stress and injury in experimental intimal thickening at PTFE end-to-side arterial anastomoses

BACKGROUND: Intimal hyperplastic thickening (IHT) is a frequent cause of prosthetic bypass graft failure. Induction and progression of IHT is thought to involve a number of mechanisms related to variation in the flow field, injury and the prosthetic nature of the conduit. This study was designed to examine the relative contribution of wall shear stress and injury to the induction of IHT at defined regions of experimental end-to-side prosthetic anastomoses. METHODS AND RESULTS: The distribution of IHT was determined at the distal end-to-side anastomosis of seven canine Iliofemoral PTFE grafts after 12 weeks of implantation. An upscaled transparent model was constructed using the in vivo anastomotic geometry, and wall shear stress was determined at 24 axial locations from laser Doppler anemometry measurements of the near wall velocity under conditions of pulsatile flow similar to that present in vivo. The distribution of IHT at the end-to-side PTFE graft was determined using computer assisted morphometry. IHT involving the native artery ranged from 0.0+/-0.1 mm to 0.05+/-0.03 mm. A greater amount of IHT was found on the graft hood (PTFE) and ranged from 0.09+/-0.06 to 0.24+/-0.06 mm. Nonlinear multivariable logistic analysis was used to model IHT as a function of the reciprocal of wall shear stress, distance from the suture line, and vascular conduit type (i.e. PTFE versus host artery). Vascular conduit type and distance from the suture line independently contributed to IHT. An inverse correlation between wall shear stress and IHT was found only for those regions located on the juxta-anastomotic PTFE graft. CONCLUSIONS: The data are consistent with a model of intimal thickening in which the intimal hyperplastic pannus migrating from the suture line was enhanced by reduced levels of wall shear stress at the PTFE graft/host artery interface. Such hemodynamic modulation of injury induced IHT was absent at the neighboring artery wall.     

A stress-strain relation for a rat abdominal aorta

Assuming the arterial wall is homogeneous, incompressible, isotropic and elastic, a stress-strain relation has been presented for a rat's abdominal aorta. As an illustrating example, the problem of simultaneous inflation and the axial stretch of a cylindrical artery under physiological loading has been solved and then the material coefficients are determined by comparing theoretical results with the existing experiments. The result indicates that the maximum deviation between the theory and experiment for various pressure levels is 3.7% which seems to be a good approximation of theory to the experiments. The variation of circumferential stress and the incremental pressure modulus with inner pressure are also depicted in the work.     

Load-dispersing design with twined-spring geometry of a distensible intracranial stent for cerebral aneurysms

Endovascular stents are increasingly being used to treat cerebral aneurysms. Mechanically, a cerebrovascular stent must have a low radial stiffness to prevent vessel dissection and rupture. To minimize these complications, we need to consider a stent design that has a low radial force and disperses the load within the stented artery. Therefore, highly distensible, load-dispersion stent designs are desirable for intracranial stenting. This study focused on closed-cell stent geometries and calculated the differences in stress within the artery because of the structure by using finite-element modeling. The results showed that the design with hexagonal cell geometry stretched in the circumferential direction had lower radial and circumferential stresses than did the other models. Comparing the maximum radial stress of our models, stress reduction of 35% was obtained with this design. Moreover, its radial stress was 47 kPa, which was similar to the critical stress of 42 kPa assumed in this study. This stent model was characterized by narrow strut spacing and a large surface area, which was dominated by the twined-spring geometry. It had low radial and circumferential stresses and a dispersed stress distribution compared with the other models. Therefore, this design is a desirable load-dispersing design for cerebrovascular treatment.     

A potential role of smooth muscle tone in early hypertension: a theoretical study

A conspicuous long-term consequence of hypertension is a thickening of the arterial wall, which many suggest returns the circumferential wall stress toward its normal value. This thickening results from an increase in smooth muscle and extracellular matrix, with the associated growth and remodeling processes depending on a host of regulatory signals that likely include the altered mechanical environment. Although the precise mechanotransduction pathways remain unknown, we propose that vasoconstriction may be an early response of the arterial wall to a step-change in pressure. In particular, computations suggest that such a response can decrease the magnitude and transmural gradients of the pressure-induced wall stresses and return the mean wall shear stress toward its homeostatic value. Such an initial 'compensatory vasoconstriction' could also help set into motion subsequent growth and remodeling responses due to growth regulatory characteristics of the vasoactive molecules (e.g., nitric oxide, endothelin-1, angiotensin-II). Although the consequences of growth and remodeling have been the focus of prior biomechanical and histological studies, early responses dictate subsequent developments and therefore deserve increased attention in vascular biomechanics and mechanobiology.     

Finite element modelling of the common carotid artery in the elderly with physiological intimal thickening using layer-specific stress-released geometries and nonlinear elastic properties

To investigate the mechanical effects of tissue responses, such as remodelling, in the arteries of the elderly, it is important to evaluate stress in the intimal layer. In this study, we investigated a novel technique to evaluate the effect of layer-specific characteristics on stress in the arterial wall in an elderly subject. We used finite element analysis of a segment of carotid artery with intimal thickening, incorporating stress-released geometries and the stress–strain relationships for three separate wall layers. We correlated the stress–strain relationships and local curvatures of the layers with the stress on the arterial wall under physiological loading. The simulation results show that both the stress–strain relationship and the local curvature of the innermost stress-released layer influence the circumferential stress and its radial gradient. This indicates that intimal stress is influenced significantly by location-dependent intimal remodelling. However, further investigation is needed before conclusive inferences can be drawn.     

Pulse waves in prestressed arteries

In order to better understand the effect of initial stress in blood flow in arteries, a theoretical analysis of wave propagation in an initially inflated and axially stretched cylindrical thick shell is investigated. For simplicity in the mathematical analysis, the blood is assumed to be an incompressible inviscid fluid while the arterial wall is taken to be an isotropic, homogeneous and incompressible elastic material. Employing the theory of small deformations superimposed on a large initial field the governing differential equations of perturbed solid motions are obtained in cylindrical polar coordinates. Considering the difficulty in obtaining a closed form solution for the field equations, an approximate power series method is utilized. The dispersion relations for the most general case of this approximation and for the thin tube case are thoroughly discussed. The speeds of waves propagating in an unstressed tube are obtained as a special case of our general treatment. It is observed that the speeds of both waves increase with increasing inner pressure and axial stretch.     

Model of geometrical and smooth muscle tone adaptation of carotid artery subject to step change in pressure

Recent experimental studies have shown significant alterations of the vascular smooth muscle (VSM) tone when an artery is subjected to an elevation in pressure. Therefore, the VSM participates in the adaptation process not only by means of its synthetic activity (fibronectins and collagen) or proliferative activity (hypertrophy and hyperplasia) but also by adjusting its contractile properties and its tone level. In previous theoretical models describing the time evolution of the arterial wall adaptation in response to induced hypertension, the contribution of VSM tone has been neglected. In this study, we propose a new biomechanical model for the wall adaptation to induced hypertension, including changes in VSM tone. On the basis of Hill's model, total circumferential stress is separated into its passive and active components, the active part being the stress developed by the VSM. Adaptation rate equations describe the geometrical adaptation (wall thickening) and the adaptation of active stress (VSM tone). The evolution curves that are derived from the theoretical model fit well the experimental data describing the adaptation of the rat common carotid subjected to a step increase in pressure. This leads to the identification of the model parameters and time constants by characterizing the rapidity of the adaptation processes. The agreement between the results of this simple theoretical model and the experimental data suggests that the theoretical approach used here may appropriately account for the biomechanics underlying the arterial wall adaptation.     

Stress-modulated growth, residual stress, and vascular heterogeneity.

A simple phenomenological model is used to study interrelations between material properties, growth-induced residual stresses, and opening angles in arteries. The artery is assumed to be a thick-walled tube composed of an orthotropic pseudoelastic material. In addition, the normal mature vessel is assumed to have uniform circumferential wall stress, which is achieved here via a mechanical growth law. Residual stresses are computed for three configurations: the unloaded intact artery, the artery after a single transmural cut, and the inner and outer rings of the artery created by combined radial and circumferential cuts. The results show that the magnitudes of the opening angles depend strongly on the heterogeneity of the material properties of the vessel wall and that multiple radial and circumferential cuts may be needed to relieve all residual stress. In addition, comparing computed opening angles with published experimental data for the bovine carotid artery suggests that the material properties change continuously across the vessel wall and that stress, not strain, correlates well with growth in arteries.     

Effect of residual stress and heterogeneity on circumferential stress in the arterial wall

Quantifying the stress distribution through the arterial wall is essential to studies of arterial growth and disease. Previous studies have shown that both residual stress, as measured by opening angle, and differing material properties for the media-intima and the adventitial layers affect the transmural circumferential stress (sigma theta) distribution. Because a lack of comprehensive data on a single species and artery has led to combinations from multiple sources, this study determined the sensitivity of sigma theta to published variations in both opening angle and layer thickness data. We fit material properties to previously published experimental data for pressure-diameter relations and opening angles of rabbit carotid artery, and predicted sigma theta through the arterial wall at physiologic conditions. Using a one-layer model, the ratio of sigma theta at the internal wall to the mean sigma theta decreased from 2.34 to 0.98 as the opening angle increased from 60 to 130 deg. In a two-layer model using a 95 deg opening angle, mean sigma theta in the adventitia increased (112 percent for 25 percent adventitia) and mean sigma theta in the media decreased (47 percent for 25 percent adventitia). These results suggest that both residual stress and wall layers have important effects on transmural stress distribution. Thus, experimental measurements of loading curves, opening angles, and wall composition from the same species and artery are needed to accurately predict the transmural stress distribution in the arterial wall.     

Does PGA external stenting reduce compliance mismatch in venous grafts?

Background  

Autogenous vein grafting is widely used in regular bypassing procedures. Due to its mismatch with the host artery in both mechanical property and geometry, the graft often over expands under high arterial blood pressure and forms a step-depth where eddy flow develops, thus causing restenosis, fibrous graft wall, etc. External stents, such as sheaths being used to cuff the graft, have been introduced to eliminate these mismatches and increase the patency. Although histological and immunochemical studies have shown some positive effects of the external stent, the mechanical mismatch under the protection of an external stent remains poorly analyzed.     

Characterization of arterial wall mechanical behavior and stresses from human clinical data

This paper demonstrates the feasibility of material identification and wall stress computation for human common carotid arteries based on non-invasive in vivo clinical data: dynamical intraluminal pressure measured by applanation tonometry, and medial diameter and intimal-medial thickness measured by high-resolution ultrasound echotracking. The mechanical behavior was quantified assuming an axially pre-stretched, thick-walled, cylindrical artery subjected to dynamical blood pressure and perivascular constraints. The wall was further assumed to be three-dimensional and to consist of a nonlinear, hyperelastic, anisotropic, incompressible material with smooth muscle activity and residual stresses. Mechanical contributions by individual constituents-an elastin-dominated matrix, collagen fibers, and vascular smooth muscle-were accounted for using a previously proposed microstructurally motivated constitutive relation. The in vivo boundary value problem was solved semi-analytically to compute the inner pressure during a mean cardiac cycle. Using a nonlinear least-squares method, optimal model parameters were determined by minimizing differences between computed and measured inner pressures over a mean cardiac cycle. The fit-to-data from two healthy patients was very good and the predicted radial, circumferential, and axial stretch and stress fields were sensible. Hence, the proposed approach was able to identify complex geometric and material parameters directly from non-invasive in vivo human data.     

Numerical study of hemodynamics and wall mechanics in distal end-to-side anastomoses of bypass grafts.

The development and progress of distal anastomotic intimal hyperplasia seems to be promoted by altered flow conditions and intramural stress distributions at the region of the artery-graft junction of vascular bypass configurations. From clinical observations, it is known that intimal hyperplasia preferentially occurs at outflow anastomoses of prosthetic bypass grafts. In order to gain a deeper insight into post-operative disease processes, and subsequently, to contribute to the development of improved vascular reconstructions with respect to long term patency rates, detailed studies are required. In context with in vivo experiments, this study was designed to analyze the flow dynamics and wall mechanics in anatomically correct bypass configurations related to two different surgical techniques and resulting geometries (conventional geometry and Miller-cuff). The influence of geometric conditions and of different compliance of synthetic graft, the host artery and the interposed venous cuff on the hemodynamic behavior and on the wall stresses are investigated. The flow studies apply the time-dependent, three-dimensional Navier-Stokes equations describing the motion of an incompressible Newtonian fluid. The vessel walls are described by a geometrically non-linear shell structure. In an iterative coupling procedure, the two problems are solved by means of the finite element method. The numerical results demonstrate non-physiological flow patterns in the anastomotic region. Strongly skewed axial velocity profiles and high secondary velocities occur downstream the artery-graft junction. On the artery floor opposite the junction, flow separation and zones of recirculation are found. The wall mechanical studies show that increased compliance mismatch leads to increased intramural stresses, and thus, may have a proliferative influence on suture line hyperplasia, as it is observed in the in vivo study.     

Effects of compliance mismatch on blood flow in an artery with endovascular prosthesis

The objective of this paper is to study the mechanical effects caused by the local stiffening of an artery (due to the vascular prosthesis, for instance). At the junction of the host artery and the more rigid implantant, the abrupt change in compliance creates an abnormal stress concentration that initiates an adaptive response in the vascular tissue. The roles of both fluid and solid mechanical phenomena must be considered in the prosthesis design optimization. In this context, even the simple models could provide helpful tools for designing process. We present here a model of blood flow in compliant vessel. The artery is supposed to be an orthotropical thin elastic shell. We obtain the solution by matched asymptotic expansions. The results prove the high flexure concentration close to the compliance jump. It is shown that the use of orthotropical graft may reduce the peak value of these shear forces to a remarkable extent. Waves reflected from the suture and pressure increase in the prosthesis are discussed. Compliance mismatch is shown to reduce the peak value of maximal wall shear stress.     

犬不同血管搭桥方法及搭桥血管内流场的计算机数值模拟

目的血管搭桥术后的内膜增生往往导致手术失败,而内膜增生与搭桥血管内的流场密切相关,为改善搭桥血管中的流场结构,作者设计了偏心搭桥手术方法,利用计算机数值模拟技术,探索偏心搭桥和传统搭桥血管中流场的变化,为血管搭桥方法提供优化设计方案。方法16只犬随机分为偏心搭桥组和传统搭桥组进行血管搭桥,测定搭桥前后血管几何数据,搭桥后近心端及远心端吻合口血流量和血压。按测定的血管几何数据,FLUENT 6.2模拟搭桥血管内的流场。结果偏心搭桥近心端和远心端吻合口不在同一平面。传统搭桥中,主体动脉远心端吻合口对应面处存在一个较低壁面剪切应力（WSS）区域及流体停滞点,离脚跟较近的一部分流体会形成涡漩,血流进入主体动脉后,还会表现出迪恩涡二次流;偏心搭桥中,主体动脉吻合口对应面上的低WSS区域和流体停滞点消失,血流接触到吻合口底面后,以切向旋转的方式改变其流动方向,不会形成涡漩,且当血流进入主体动脉后,立即发生螺旋流态且能持续很长一段。结论偏心搭桥能够产生血液旋动流,显著增加远心端血流量、提高WSS。     

Effect of balloon pre-dilation on performance of self-expandable nitinol stent in femoropopliteal artery

Balloon pre-dilation is usually performed before implantation of a nitinol stent in a femoropopliteal artery in a case of severe blockage or calcified plaque. However, its effect on performance of the nitinol stent in a diseased femoropopliteal artery has not been studied yet. This study compares the outcomes of stenting with pre-dilation and without it by modelling the entire processes of stent deployment. Fatigue deformation of the implanted stent is also modelled under diastolic–systolic blood pressure, repetitive bending, torsion, axial compression and their combination. Reduced level of stress in the stent occurs after stenting with pre-dilation, but causing the increased damage in the media layer, i.e. the middle layer of the arterial wall. Generally, pre-dilation increases the risk of nitinol stent’s fatigue failure. Additionally, the development of in-stent restenosis is predicted based on the stenting-induced tissue damage in the media layer, and no severe mechanical irritation is induced to the media layer by pre-dilation, stent deployment or fatigue loading.

     

Structural analysis of two different stent configurations

Two different stent configurations (i.e. the well known Palmaz–Schatz (PS) and a new stent configuration) are mechanically investigated. A finite element model was used to study the two geometries under combining loads and a computational fluid dynamic model based on fluid structure interaction was developed investigating the plaque and the artery wall reactions in a stented arterial segment. These models determine the stress and displacement fields of the two stents under internal pressure conditions. Results suggested that stent designs cause alterations in vascular anatomy that adversely affect arterial stress distributions within the wall, which have impact in the vessel responses such as the restenosis. The hemodynamic analysis shows the use of new stent geometry suggests better biofluid mechanical response such as the deformation and the progressive amount of plaque growth.