Electricity generation using p-nitrophenol as substrate in microbial fuel cell

The cell voltage and degradation rate of p-nitrophenol (PNP) were monitored in a two-chambered microbial fuel cell (MFC) system. Degradation metabolites in the anode solution of MFC were analyzed by gas chromatography–mass spectrometry (GC–MS). PNP was used as substrate by the MFC that was inoculated with anaerobic sludge. The results showed that electricity output increased with the PNP concentration increased, the MFC displayed a maximum power density of 1.778 mW m⁻² and a maximum PNP degradation rate of 64.69% when PNP was used as a sole substrate. However, the cell voltage and the PNP degradation rate with sodium acetate (402.3 mV and 95.96%) were higher than those fed with glucose (341.9 mV and 83.51%) when glucose and sodium acetate were used as a substrate, respectively. Furthermore, GC–MS analysis showed that the PNP was biodegraded completely after 142 h in the MFC. These results demonstrate that PNP can be used for electricity generation in MFC for practical applications of wastewater treatment.     

Electricity generation and microbial community changes in microbial fuel cells packed with different anodic materials

Four materials, carbon felt cube (CFC), granular graphite (GG), granular activated carbon (GAC) and granular semicoke (GS) were tested as packed anodic materials to seek a potentially practical material for microbial fuel cells (MFCs). The microbial community and its correlation with the electricity generation performance of MFCs were explored. The maximum power density was found in GAC, followed by CFC, GG and GS. In GAC and CFC packed MFCs, Geobacter was the dominating genus, while Azospira was the most populous group in GG. Results further indicated that GAC was the most favorable for Geobacter adherence and growth, and the maximum power densities had positive correlation with the total biomass and the relative abundance of Geobacter, but without apparent correlation with the microbial diversity. Due to the low content of Geobacter in GS, power generated in this system may be attributed to other microorganisms such as Synergistes, Bacteroidetes and Castellaniella.     

Electricity generation and microbial community analysis of alcohol powered microbial fuel cells

Two different microbial fuel cell (MFC) configurations were investigated for electricity production from ethanol and methanol: a two-chambered, aqueous-cathode MFC; and a single-chamber direct-air cathode MFC. Electricity was generated in the two-chamber system at a maximum power density typical of this system (40+/-2 mW/m2) and a Coulombic efficiency (CE) ranging from 42% to 61% using ethanol. When bacteria were transferred into a single-chamber MFC known to produce higher power densities with different substrates, the maximum power density increased to 488+/-12 mW/m2 (CE = 10%) with ethanol. The voltage generated exhibited saturation kinetics as a function of ethanol concentration in the two-chambered MFC, with a half-saturation constant (Ks) of 4.86 mM. Methanol was also examined as a possible substrate, but it did not result in appreciable electricity generation. Analysis of the anode biofilm and suspension from a two-chamber MFC with ethanol using 16S rDNA-based techniques indicated that bacteria with sequences similar to Proteobacterium Core-1 (33.3% of clone library sequences), Azoarcus sp. (17.4%), and Desulfuromonas sp. M76 (15.9%) were significant members of the anode chamber community. These results indicate that ethanol can be used for sustained electricity generation at room temperature using bacteria on the anode in a MFC.     

微生物燃料电池利用乳酸产电性能与微生物群落分布特征

【目的】为探讨以乳酸为基质的微生物燃料电池(Microbial fuel cell,MFC)产电性能以及微生物群落在阳极膜、悬浮液、阳极沉淀污泥中的分布特征,【方法】试验建立了双室MFC,以乳酸为阳极主要碳源,研究了反应器的启动过程及产电效能,同时以电镜和PCR-变性梯度凝胶电泳(Denaturing gradient gelelectrophoresis,DGGE)技术解析了微生物群落的空间分布特征。【结果】结果表明,反应器启动第7天时外电压达到0.56 V,当外阻为80Ω时,电流密度为415 mA/m2,MFC的功率密度达到最大值82 mW/m2。电镜观察发现大量杆菌附着在阳极表面,结合较为紧密;DGGE图谱显示阳极膜表面微生物与种泥最为相似,与阳极悬浮液、底部沉淀污泥中的主要菌群一致,条带序列与睾丸酮丛毛单胞菌(Comamonas testosteroni)和布氏弓形菌(Arcobacter butzleri)等最为相似。【结论】本研究表明以乳酸为基质MFC可产生较高的功率密度,阳极附着的优势菌与接种污泥来源密切相关。     

Electricity generation coupled to oxidation of propionate in a microbial fuel cell

Propionate was used as fuel to enrich an electrochemically-active microbial consortium in a microbial fuel cell, and the bacterial consortium was analyzed by culture-independent methods including denaturing gradient gel electrophoresis (DGGE) of the 16S rDNA, and by fluorescent in situ hybridization (FISH). MFCs fed with propionate produced a current of 4.88 ± 0.1 mA stably on 100 mg propionate/l as COD within 3 weeks of the enrichment. When the MFCs were fed with H₂-saturated fuel containing propionate, the current dropped to 3.82 ± 0.07 mA. The maximum current generated was up to 8.8 mA when MFCs were fed with 200 mg propionate/l as COD. The DGGE of 16S rDNA showed that propionate-enriched MFCs have a different bacterial population from that enriched with acetate and from the inoculum used for enrichment. The major member (42%) of the consortium was an unidentified bacterium followed by γ, β, and δ-proteobacteria.     

Electricity generation from carbon monoxide and syngas in a microbial fuel cell

Electricity generation in microbial fuel cells (MFCs) has been a subject of significant research efforts. MFCs employ the ability of electricigenic bacteria to oxidize organic substrates using an electrode as an electron acceptor. While MFC application for electricity production from a variety of organic sources has been demonstrated, very little research on electricity production from carbon monoxide and synthesis gas (syngas) in an MFC has been reported. Although most of the syngas today is produced from non-renewable sources, syngas production from renewable biomass or poorly degradable organic matter makes energy generation from syngas a sustainable process, which combines energy production with the reprocessing of solid wastes. An MFC-based process of syngas conversion to electricity might offer a number of advantages such as high Coulombic efficiency and biocatalytic activity in the presence of carbon monoxide and sulfur components. This paper presents a discussion on microorganisms and reactor designs that can be used for operating an MFC on syngas.     

Electricity generation from bio-treatment of sewage sludge with microbial fuel cell

A two-chambered microbial fuel cell (MFC) with potassium ferricyanide as its electron acceptor was utilized to degrade excess sewage sludge and to generate electricity. Stable electrical power was produced continuously during operation for 250 h. Total chemical oxygen demand (TCOD) of sludge was reduced by 46.4% when an initial TCOD was 10,850 mg/l. The MFC power output did not significantly depend on process parameters such as substrate concentration, cathode catholyte concentration, and anodic pH. However, the MFC produced power was in close correlation with the soluble chemical oxygen demand (SCOD) of sludge. Furthermore, ultrasonic pretreatment of sludge accelerated organic matter dissolution and, hence, TCOD removal rate in the MFC was increased, but power output was insignificantly enhanced. This study demonstrates that this MFC can generate electricity from sewage sludge over a wide range of process parameters.     

Electricity generation using a baffled microbial fuel cell convenient for stacking

To make sure that microbial fuel cells (MFCs) are more convenient to stack, a baffled single-chambered MFC with two groups of electrodes sharing only one anode chamber was designed and the performance was examined. The experiments showed that the prototype MFC generated electrical power (maximum of 133 mW/m(2)) while removing up to 88% of chemical oxygen demand (COD) in 91 h. Volumetric power increased as electrode area per anode compartment volume increased, indicating that the MFC with two groups of electrodes was better than that with one group. Power density as a function of wastewater concentration was modeled according to saturation kinetics, with a maximum power density of P(max)=164 mW/m(2) (fixed 100 Omega resistor) and half-saturation concentration of K(s)=259 mg/l. The hydraulic retention time (HRT) was examined as a factor influencing the power generation. When it was 15.5h, the voltage and the power density reached the maximum 0.413 V and 108 mW/m(2).     

Electricity generation in a microbial fuel cell with a microbially catalyzed cathode

A microbial fuel cell using aerobic microorganisms as the cathodic catalysts is described. By using anaerobic sludge in the anode and aerobic sludge in the cathode as inocula, the microbial fuel cell could be started up after a short lag time of 9 days, generating a stable voltage of 0.324 V (R (ex) = 500 Omega). At an aeration rate of 300 ml min(-1) in the cathode, a maximum volumetric power density of up to 24.7 W m(-3) (117.2 A m(-3)) was reached. This research demonstrates an economic system for recovering electrical energy from organic compounds.     

Electricity generation from model organic wastewater in a cassette-electrode microbial fuel cell

A new highly scalable microbial fuel cell (MFC) design, consisting of a series of cassette electrodes (CE), was examined for increasing power production from organic matter in wastewater. Each CE chamber was composed of a box-shaped flat cathode (two air cathodes on both sides) sandwiched in between two proton-exchange membranes and two graphite-felt anodes. Due to the simple design of the CE-MFC, multiple cassettes can be combined to form a single unit and inserted into a tank to treat wastewater. A 12-chamber CE-MFC was tested using a synthetic wastewater containing starch, peptone, and fish extract. Stable performance was obtained after 15 days of operation in fed-batch mode, with an organic removal efficiency of 95% at an organic loading rate of 2.9 kg chemical oxygen demand (COD) per cubic meter per day and an efficiency of 93% at 5.8 kg COD per cubic meter per day. Power production was stable during this period, reaching maximum power densities of 129 W m(-3) (anode volume) and 899 mW m(-2) (anode projected area). The internal resistance of CE-MFC decreased from 2.9 (day 4) to 0.64 Omega (day 25). These results demonstrate the usefulness of the CE-MFC design for energy production and organic wastewater treatment.     

Electricity generation from polyalcohols in single-chamber microbial fuel cells

Six polyalcohols derived from lignocellulosic carbohydrates were investigated as carbon sources for electricity generation in single-chamber mediator-less microbial fuel cells (MFCs) for the first time. Electricity was directly generated from all polyalcohols tested, including pentitols (xylitol, arabitol, and ribitol) and hexitols (galactitol, mannitol, and sorbitol). Bacterial cultures initially enriched using acetate could be adapted to these substrates with varied adaptation times. The resultant maximum power density ranged from 1490+/-160 mW/m(2) to 2650+/-10 mW/m(2) at current densities between 0.58 mA/cm(2) and 0.78 mA/cm(2). Galactitol generated the highest maximum power density, while mannitol resulted in the lowest one. The estimated maximum voltage output at an external resistance of 120 Omega ranged between 0.24 V and 0.34 V with half saturation kinetic constants varied from 298 mg/L to 753 mg/L. The removal of chemical oxygen demand (COD) was above 91% for all polyalcohols except sorbitol (71%). Denaturing gradient gel electrophoresis (DGGE) of PCR-amplified 16S rRNA gene segments of the anode biofilms showed the influence of substrates (polyalcohols) on the anode microbial populations.     

Electricity generation and treatment of paper recycling wastewater using a microbial fuel cell

Increased interest in sustainable agriculture and bio-based industries requires that we find more energy-efficient methods for treating cellulose-containing wastewaters. We examined the effectiveness of simultaneous electricity production and treatment of a paper recycling plant wastewater using microbial fuel cells. Treatment efficiency was limited by wastewater conductivity. When a 50 mM phosphate buffer solution (PBS, 5.9 mS/cm) was added to the wastewater, power densities reached 501 +/- 20 mW/m(2), with a coulombic efficiency of 16 +/- 2%. There was efficient removal of soluble organic matter, with 73 +/- 1% removed based on soluble chemical oxygen demand (SCOD) and only slightly greater total removal (76 +/- 4%) based on total COD (TCOD) over a 500-h batch cycle. Cellulose was nearly completely removed (96 +/- 1%) during treatment. Further increasing the conductivity (100 mM PBS) increased power to 672 +/- 27 mW/m(2). In contrast, only 144 +/- 7 mW/m(2) was produced using an unamended wastewater (0.8 mS/cm) with TCOD, SCOD, and cellulose removals of 29 +/- 1%, 51 +/- 2%, and 16 +/- 1% (350-h batch cycle). These results demonstrate limitations to treatment efficiencies with actual wastewaters caused by solution conductivity compared to laboratory experiments under more optimal conditions.     

Electricity generation and modeling of microbial fuel cell from continuous beer brewery wastewater

Electricity production and modeling of microbial fuel cell (MFC) from continuous beer brewery wastewater was studied in this paper. A single air-cathode MFC was constructed, carbon fiber was used as anode and diluted brewery wastewater (COD = 626.58 mg/L) as substrate. The MFC displayed an open-circuit voltage of 0.578 V and a maximum power density of 9.52 W/m³ (264 mW/m²). Using the model based on polarization curve, various voltage losses were quantified. At current density of 1.79 A/m², reaction kinetic loss and mass transport loss both achieved to 0.248 V; while ohmic loss was 0.046 V. Results demonstrated that it was feasible and stable for producing bioelectricity from brewery wastewater; while the most important factors which influenced the performance of the MFC are reaction kinetic loss and mass transport loss.     

Electricity generation from synthesis gas by microbial processes: CO fermentation and microbial fuel cell technology

A microbiological process was established to harvest electricity from the carbon monoxide (CO). A CO fermenter was enriched with CO as the sole carbon source. The DGGE/DNA sequencing results showed that Acetobacterium spp. were enriched from the anaerobic digester fluid. After the fermenter was operated under continuous mode, the products were then continuously fed to the microbial fuel cell (MFC) to generate electricity. Even though the conversion yield was quite low, this study proved that synthesis gas (syn-gas) can be converted to electricity with the aid of microbes that do not possess the drawbacks of metal catalysts of conventional methods.     

Electricity generation in a membrane-less microbial fuel cell with down-flow feeding onto the cathode

A novel membrane-less microbial fuel cell (MFC) with down-flow feeding was constructed to generate electricity. Wastewater was fed directly onto the cathode which was horizontally installed in the upper part of the MFC. Oxygen could be utilized readily from the air. The concentration of dissolved oxygen in the influent wastewater had little effect on the power generation. A saturation-type relationship was observed between the initial COD and the power generation. The influent flow rate could affect greatly the power density. Fed by the synthetic glucose wastewater with a COD value of 3500 mg/L at a flow rate of 4.0 mL/min, the developed MFC could produce a maximum power density of 37.4 mW/m². Its applicability was further evaluated by the treatment of brewery wastewater. The system could be scaled up readily due to its simple configuration, easy operation and relatively high power density.     

Electricity generation using chocolate industry wastewater and its treatment in activated sludge based microbial fuel cell and analysis of developed microbial community in the anode chamber

Feasibility of using chocolate industry wastewater as a substrate for electricity generation using activated sludge as a source of microorganisms was investigated in two-chambered microbial fuel cell. The maximum current generated with membrane and salt bridge MFCs was 3.02 and 2.3 A/m², respectively, at 100 Ω external resistance, whereas the maximum current generated in glucose powered MFC was 3.1 A/m². The use of chocolate industry wastewater in cathode chamber was promising with 4.1 mA current output. Significant reduction in COD, BOD, total solids and total dissolved solids of wastewater by 75%, 65%, 68%, 50%, respectively, indicated effective wastewater treatment in batch experiments. The 16S rDNA analysis of anode biofilm and suspended cells revealed predominance of β-Proteobacteria clones with 50.6% followed by unclassified bacteria (9.9%), α-Proteobacteria (9.1%), other Proteobacteria (9%), Planctomycetes (5.8%), Firmicutes (4.9%), Nitrospora (3.3%), Spirochaetes (3.3%), Bacteroides (2.4%) and γ-Proteobacteria (0.8%). Diverse bacterial groups represented as members of the anode chamber community.     

Electricity generation from cellulose by rumen microorganisms in microbial fuel cells

In microbial fuel cells (MFCs) bacteria generate electricity by mediating the oxidation of organic compounds and transferring the resulting electrons to an anode electrode. The objective of this study was to test the possibility of generating electricity with rumen microorganisms as biocatalysts and cellulose as the electron donor in two-compartment MFCs. The anode and cathode chambers were separated by a proton exchange membrane and graphite plates were used as electrodes. The medium in the anode chamber was inoculated with rumen microorganisms, and the catholyte in the cathode compartment was ferricyanide solution. Maximum power density reached 55 mW/m(2) (1.5 mA, 313 mV) with cellulose as the electron donor. Cellulose hydrolysis and electrode reduction were shown to support the production of current. The electrical current was sustained for over 2 months with periodic cellulose addition. Clarified rumen fluid and a soluble carbohydrate mixture, serving as the electron donors, could also sustain power output. Denaturing gradient gel electrophoresis (DGGE) of PCR amplified 16S rRNA genes revealed that the microbial communities differed when different substrates were used in the MFCs. The anode-attached and the suspended consortia were shown to be different within the same MFC. Cloning and sequencing analysis of 16S rRNA genes indicated that the most predominant bacteria in the anode-attached consortia were related to Clostridium spp., while Comamonas spp. abounded in the suspended consortia. The results demonstrated that electricity can be generated from cellulose by exploiting rumen microorganisms as biocatalysts, but both technical and biological optimization is needed to maximize power output.     

好氧-厌氧混合污泥启动微生物燃料电池产电性能及微生物群落动态特征

【目的】为探讨好氧-厌氧混合污泥启动微生物燃料电池(Microbial fuel cell,MFC)产电性能以及MFC对微生物群落的选择作用,【方法】以乳酸为底物,应用不依赖于培养的微生物分子生物学技术解析单室MFC启动过程中微生物群落的组成和结构动态学特征。【结果】结果表明,MFC经过3个周期启动成功,最高输出电压230 m V。当MFC外电阻为1656Ω时,最大功率密度11.15 W/m3,电池运行稳定。混合污泥启动MFC以后,阳极生物膜微生物群落结构同种泥差异较大,且多样性降低。生物膜中微生物类群按丰度依次为β-变形菌纲(Betaproteobacteria)24.90%、拟杆菌门(Bacteroidetes)21.30%、厚壁菌门(Firmicutes)9.70%、γ-变形菌纲(Gammaproteobacteria)8.50%、δ-变形菌纲(Deltaproteobacteria)7.90%、绿弯菌门(Chloroflexi)4.20%以及α-变形菌纲(Alphaproteobacteria)3.60%。有利于生物膜形成与稳定的动胶菌属(Zoogloea)和不动杆菌属(Acinetobacter)序列丰度分别占生物膜群落的5.00%和3.90%,与MFC产电能力直接相关的地杆菌属(Geobacter)序列由混合污泥中的0.60%上升至阳极生物膜中的2.60%。【结论】本研究表明,MFC阳极生物膜在驯化过程中对污泥中的微生物进行淘汰和选择,最终驯化形成了有利于生物膜形成与稳定、有机物厌氧发酵与产电的微生物菌群。     

Continuous power generation and microbial community structure of the anode biofilms in a three-stage microbial fuel cell system

A mediator-less three-stage two-chamber microbial fuel cell (MFC) system was developed and operated continuously for more than 1.5 years to evaluate continuous power generation while treating artificial wastewater containing glucose (10 mM) concurrently. A stable power density of 28 W/m³ was attained with an anode hydraulic retention time of 4.5 h and phosphate buffer as the cathode electrolyte. An overall dissolved organic carbon removal ratio was about 85%, and coulombic efficiency was about 46% in this MFC system. We also analyzed the microbial community structure of anode biofilms in each MFC. Since the environment in each MFC was different due to passing on the products to the next MFC in series, the microbial community structure was different accordingly. The anode biofilm in the first MFC consisted mainly of bacteria belonging to the Gammaproteobacteria, identified as Aeromonas sp., while the Firmicutes dominated the anode biofilms in the second and third MFCs that were mainly fed with acetate. Cyclic voltammetric results supported the presence of a redox compound(s) associated with the anode biofilm matrix, rather than mobile (dissolved) forms, which could be responsible for the electron transfer to the anode. Scanning electron microscopy revealed that the anode biofilms were comprised of morphologically different cells that were firmly attached on the anode surface and interconnected each other with anchor-like filamentous appendages, which might support the results of cyclic voltammetry. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.