Evaluation of stability and size distribution of sunflower oil-coated micro bubbles for localized drug delivery

Background

In recent years magnesium alloys have been intensively investigated as potential resorbable materials with appropriate mechanical and corrosion properties. Particularly in orthopedic research magnesium is interesting because of its mechanical properties close to those of natural bone, the prevention of both stress shielding and removal of the implant after surgery.

Methods

ZEK100 plates were examined in this in vitro study with Hank's Balanced Salt Solution under physiological conditions with a constant laminar flow rate. After 14, 28 and 42 days of immersion the ZEK100 plates were mechanically tested via four point bending test. The surfaces of the immersed specimens were characterized by SEM, EDX and XRD.

Results

The four point bending test displayed an increased bending strength after 6 weeks immersion compared to the 2 week group and 4 week group. The characterization of the surface revealed the presence of high amounts of O, P and Ca on the surface and small Mg content. This indicates the precipitation of calcium phosphates with low solubility on the surface of the ZEK100 plates.

Conclusions

The results of the present in vitro study indicate that ZEK100 is a potential candidate for degradable orthopedic implants. Further investigations are needed to examine the degradation behavior.     

Dynamics of amino acids in the conditioning film developed on glass panels immersed in the surface seawaters of Dona Paula Bay

The conditioning film developed on glass panels immersed in surface seawater over a period of 24?h was analysed for total organic carbon (OC), total organic nitrogen (ON), and total hydrolyzable amino acid (THAA) concentrations and composition. The concentrations of C and N and THAA increased, whereas the C/N ratio decreased over the period of immersion. The amino acid-C and N accounted for 3.7?–?6.7% and 10.3?–?65.3% of OC and ON, respectively. The relative contribution of glycine plus threonine and serine to the total amino acids decreased while that of valine, phenylalanine, isoleucine and leucine increased over the period of immersion. Principal component analysis (PCA) based on mole% amino acid composition showed that the degradation indices (DI) for the conditioning film organic matter increased over the period of immersion. A high C/N ratio, a low %THAA-C, % THAA-N and DI values and the abundance of glycine plus threonine and serine in the conditioning film organic matter during the first few hours following immersion imply that the adsorbed organic matter was mostly derived from degraded organic matter.     

Dynamics of amino acids in the conditioning film developed on glass panels immersed in the surface seawaters of Dona Paula Bay

The conditioning film developed on glass panels immersed in surface seawater over a period of 24 h was analysed for total organic carbon (OC), total organic nitrogen (ON), and total hydrolyzable amino acid (THAA) concentrations and composition. The concentrations of C and N and THAA increased, whereas the C/N ratio decreased over the period of immersion. The amino acid-C and N accounted for 3.7-6.7% and 10.3-65.3% of OC and ON, respectively. The relative contribution of glycine plus threonine and serine to the total amino acids decreased while that of valine, phenylalanine, isoleucine and leucine increased over the period of immersion. Principal component analysis (PCA) based on mole% amino acid composition showed that the degradation indices (DI) for the conditioning film organic matter increased over the period of immersion. A high C/N ratio, a low %THAA-C, % THAA-N and DI values and the abundance of glycine plus threonine and serine in the conditioning film organic matter during the first few hours following immersion imply that the adsorbed organic matter was mostly derived from degraded organic matter.     

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) degradation by <Emphasis Type="Italic">Acetobacterium paludosum</Emphasis>

Substrates and nutrients are often added to contaminated soil or groundwater to enhance bioremediation. Nevertheless, this practice may be counterproductive in some cases where nutrient addition might relieve selective pressure for pollutant biodegradation. Batch experiments with a homoacetogenic pure culture of Acetobacterium paludosum showed that anaerobic RDX degradation is the fastest when auxiliary growth substrates (yeast extract plus fructose) and nitrogen sources (ammonium) are not added. This bacterium degraded RDX faster under autotrophic (H₂-fed) than under heterotrophic conditions, even though heterotrophic growth was faster. The inhibitory effect of ammonium is postulated to be due to the repression of enzymes that initiate RDX degradation by reducing its nitro groups, based on the known fact that ammonia represses nitrate and nitrite reductases. This observation suggests that the absence of easily assimilated nitrogen sources, such as ammonium, enhances RDX degradation. Although specific end products of RDX degradation were not determined, the production of nitrous oxide (N₂O) suggests that A. paludosum cleaved the triazine ring.     

Effect of surface roughness of Ti, Zr, and TiZr on apatite precipitation from simulated body fluid

Some of the critical properties for a successful orthopedic or dental implant material are its biocompatibility and bioactivity. Pure titanium (Ti) and zirconium (Zr) are widely accepted as biocompatible metals, due to their non-toxicity. While the bioactivity of Ti and some Ti alloys has been extensively investigated, there is still insufficient data for Zr and titanium-zirconium (TiZr) alloys. In the present study, the bioactivity, that is, the apatite forming ability on the alkali and heat treated surfaces of Ti, Zr, and TiZr alloy in simulated body fluid (SBF), was studied. In particular, the effect of the surface roughness characteristics on the bioactivity was evaluated for the first time. The results indicate that the pretreated Ti, Zr and TiZr alloy could form apatite coating on their surfaces. It should be noted that the surface roughness also critically affected the bioactivity of these pretreated metallic samples. A surface morphology with an average roughness of approximately 0.6 microm led to the fastest apatite formation on the metal surfaces. This apatite layer on the metal surface is expected to bond to the surrounding bones directly after implantation.     

Mathematical modelling of the degradation behaviour of biodegradable metals

A mathematical model for the biodegradation of magnesium is developed in this study to inspect the corrosion behaviour of biodegradable implants. The aim of this study was to provide a suitable framework for the assessment of the corrosion rate of magnesium which includes the process of formation/dissolution of the protective film. The model is intended to aid the design of implants with suitable geometries. The level-set method is used to follow the changing geometry of the implants during the corrosion process. A system of partial differential equations is formulated based on the physical and chemical processes that occur at the implant-medium boundary in order to simulate the effect of the formation of a protective film on the degradation rate. The experimental data from the literature on the corrosion of a high-purity magnesium sample immersed in simulated body fluid is used to calibrate the model. The model is then used to predict the degradation behaviour of a porous orthopaedic implant. The model successfully reproduces the precipitation of the corrosion products on the magnesium surface and the effect on the degradation rate. It can be used to simulate the implant degradation and the formation of the corrosion products on the surface of biodegradable magnesium implants with complex geometries.     

Ethanol, BTEX and microbial community interactions in E-blend contaminated soil slurry

Degradation of benzene, toluene, ethylbenzene, m-, p- and o-xylenes (BTEX) and microbial community shifts in soil slurries contaminated with ethanol–gasoline blends (E-blends), containing 10, 50 or 90% (v/v) ethanol (E10, E50 and E90) were studied in soil slurries previously uncontaminated, contaminated by E-blends or ethanol. BTEX originating from E50 degraded fastest whereas from E10 slowest. Among the individual compounds, ethylbenzene degraded fastest (max 30% d⁻¹), and o-xylene slowest (min 1% d⁻¹) during aerobic conditions in previously not contaminated soils. Previous contamination by E-blends increased BTEX degradation significantly (3–19 times) compared with previously uncontaminated soils, whereas previous contamination with ethanol did not show significant difference in BTEX degradation. At least one type of the E-blends during aerobic conditions had a positive effect on total PLFAs (phospholipid fatty acids) and specific PLFAs, i.e. 10Me18:0, 16:1ω6 and cy17:0, but had a negative effect on cy19:0 and 18:2ω6,9c. The effects on total PLFAs, as well as the individual PLFAs, were particularly strong after repeated contamination. The single most affected PLFA was 16:1ω6, which increased 23 times during E10 treatment in soil slurries previously contaminated by E-blends. Altogether, the various E-blends had significantly different effects on BTEX degradation and also on individual PLFAs under aerobic conditions.     

聚丁二酸丁二醇酯降解菌株的筛选及其降解性能研究

从石油污染土壤中筛选到1株具有聚丁二酸丁二醇酯降解能力的菌株PBS1302,经菌体形态特征、菌落培养特征、生理生化鉴定和16S r DNA基因序列分析,初步鉴定为铜绿假单胞菌(Pseudomonas aeruginosa)。该菌株在培养温度37℃,培养基起始p H 6.8的条件下经6 d的培养,对聚丁二酸丁二醇酯薄膜的降解率可达36.9%。经电子显微镜观察,与降解前相比,聚丁二酸丁二醇酯薄膜表面变得粗糙,出现明显的蚀刻痕迹。     

Controlled release of all-trans-retinoic acid from PEGylated gelatin nanopaticles by enzymatic degradation

A new targeting drug carrier for anticancer drug, all-trans-retinoic acid (atRA), was proposed by using angiogenesis which is one of the specific physiological properties of cancer cells. The proposed drug carrier was prepared as PEGylated gelatin nanoparticle (176 nm size). The gelatin molecules were aggregated by coupled deoxycholic acid and the surface of the nanoparticles was covered by polyethylene glycol to reduce reticuloendothelial system (RES) uptake. To prove the feasibility of the nanoparticles as a targeting drug carrier, the degradation of the nanoparicles by collagenase IV and the release pattern of atRA from the nanoparticles by enzymatic degradation were evaluated. The PEGylated gelatin nanoparticles were significantly degraded by collagenase IV within 10 seconds, with most of them degraded within 1 min. When atRA loaded in the PEGylated gelatin nanoparticles was released in phosphate buffered saline (PBS), only twelve percent of atRA were released for one hour. However, when the nanoparticles were put into PBS with collagenase IV of 0.1 μM, a burst effect of atRA was about 40% for the initial 10 min, followed by a continuous release of atRA upto 75% for 5 hr. Therefore, the PEGylated gelatin nanoparticles released anticancer drug very sensitively by collagenase IV, which is one of major matrix metalloproteases involved in angiogenesis. These results showed a feasibility that PEGylated gelatin nanoparticles could be used as a new targeting anticancer drug carrier using angiogenesis as a specific physiological property of cancer cells.     

可降解镁合金材料在医学领域的研究和应用现状

作为最有潜力的第三代生物材料,新型可降解镁合金具有良好的生物相容性,与人体骨骼相近的力学性能,可避免二次手 术带来的不良影响等诸多优点,已成为当今研究的热点之一。然而镁合金在医学中的应用也受到其降解速度过快和随之引起机 械完整性丧失的影响。随着对镁合金研究的深入,在控制降解方面的研究已有显著成效。目前关于镁合金的研究主要集中在改善 其生物相容性、耐腐蚀性和机械性能等方面。本文将从镁合金降解产物对机体的影响,降解速度的控制和在医学中应用对其在当 今科研领域的研究进行综述。     

Degradation of aliphatic polyester films by commercially available lipases with special reference to rapid and complete degradation of poly(L-lactide) film by lipase PL derived from Alcaligenes sp

Commercial lipases were examined for their degradation efficiency of aliphatic polyester films. In 100 days immersion of polyester films in lipase solutions at37 °C at pH 7.0,Lipase Asahi derived from Chromobacterium viscosum degraded polybutylene succinate-co-adipate (PBSA), poly (-caprolactone) (PCL) and polybutylene succinate (PBS), and Lipase F derived from Rhizopus niveus degraded PBSA and PCL during 4–17 days. Lipase F-AP15 derived fromRhizopus orizae could degrade PBSA in 22 days. In these cases, PBS and PBSA were mainly degraded to dimers, whereas PCL was mainly degraded to monomers. Only poly(3-hydroxybutyrate-co-3-hydroxyvalerate)(PHB/V) and poly (L-lactide) (PLA) were not degraded in the experiments. However, PLA degraded completely at 55 °C, pH 8.5 with Lipase PL during 20 days. This result could be explained with the sequential reactions of the chemical hydrolysis of the polymer to oligomers at higher pH and temperature, and the succeeding enzymatic hydrolysis of oligomers to the monomers.     

Study of the effect of seven-day immersion on the excretory function of the kidneys

The excretion of total protein, creatinine, urea, uric acid, glucose, potassium, sodium, calcium, phosphorus, and magnesium, as well as the uroproteinogram (12 groups of proteins) and uroenzymogram (five enzymes) parameters, was studied in the experiment with seven-day immersion in eight men aged 21–26 years. The results of the study allow a conclusion that seven-day immersion did not lead to any unfavorable changes in the renal function. The study of the uroproteinogram showed the absence of shifts in either glomerular filtration or tubular reabsorption, which agrees with the absence of significant changes in the uroenzymogram values. Even in significantly increased diuresis, the physiological norm of protein and glucose excretion was not exceeded; the electrolyte excretion was normalized quickly enough. An increased excretion of creatinine, urea, calcium, magnesium, and phosphorus appears to reflect activation of catabolic processes in skeletal muscles.     

钛合金植入体表面抗感染涂层的制备及其体外抑菌性能研究

临床中,内植物引起的相关感染是矫形外科以及创伤外科面临的重要问题。以聚乳酸（PDLLA）为载体,采用溶剂浇铸（solvent-casting）的方法,在钛合金植入物基体表面制备了载万古霉素（VCM）的PDLLA涂层,期望通过缓释万古霉素来抑制细菌感染。体外释药实验表明,涂层具有良好的缓释作用,在磷酸盐缓冲液（PBS）中持续释放VCM20天以上;涂层对引起感染的主要致病菌（金黄色葡萄球菌）具有超过15天的抑制作用。提示该涂层钛合金植入物有望在预防植入材料相关感染方面获得应用。     

Biocompatible DCPD Coating Formed on AZ91D Magnesium Alloy by Chemical Deposition and Its Corrosion Behaviors in SBF

Bioactive calcium phosphate coatings were prepared on AZ91D magnesium alloy in phosphating solution in order to im- prove the corrosion resistance of the magnesium alloy in Simulated Body Fluid （SBF）. The surface morphologies and compo- sitions of the calcium phosphate coatings deposited in the phosphating bath with different compositions were investigated by Scanning Electron Microscopy （SEM） with Energy Dispersive Spectrometer （EDS） and X-ray Diffraction （XRD）. Results showed that the calcium phosphate coating was mainly composed of dicalcium phosphate dihydrate （CaHPO4o2H20, DCPD）, with Ca/P ratio of approximately 1 ： 1. The corrosion resistance was evaluated by acid drop, electrochemical polarization, elec- trochemical impedance spectroscopy and immersion tests. The dense and uniform calcium phosphate coating obtained from the optimal phosphating bath can greatly decrease the corrosion rate and hydrogen evolution rate of AZ91D magnesium alloy in SBE     

In Vivo Corrosion Resistance of Ca-P Coating on AZ60 Magnesium Alloy

Magnesium-based alloys are frequently reported as potential biodegradable orthopedic implant materials. Controlling the degradation rate and mechanical integrity of magnesium alloys in the physiological environment is the key to their applications. In this study, calcium phosphate (Ca-P) coating was prepared on AZ60 magnesium alloy using phosphating technology. AZ60 samples were immersed in a phosphating solution at 37 ± 2 °C for 30 min, and the solution pH was adjusted to 2.6 to 2.8 by adding NaOH solution. Then, the samples were dried in an attemperator at 60 °C. The degradation behavior was studied in vivo using Ca-P coated and uncoated magnesium alloys. Samples of these two different materials were implanted into rabbit femora, and the corrosion resistances were evaluated after 1, 2, and 3 months. The Ca-P coated samples corroded slower than the uncoated samples with prolonged time. Significant differences (p < 0.05) in mass losses and corrosion rates between uncoated samples and Ca-P coated samples were observed by micro-computed tomography. The results indicate that the Ca-P coating could slow down the degradation of magnesium alloy in vivo.     

Biomimetic implant coatings

Biomaterials and tissue engineering technologies are becoming increasingly important in biomedical practice, particularly as the population ages. Cellular responses depend on topographical properties of the biomaterial at the nanometer scale. Structures on biomaterial surfaces are used as powerful tools to influence or even control interactions between implants and the biological system [; ]. The influence of nanometer sized surface structures on osteoblastlike cell interactions was tested with niobium oxide coatings on polished titanium slices (cp-Ti grade 2). The aim of the study was to investigate the influence of nanoscopic surface structures on osteoblast interactions in order to support collagen I production and cell adhesion. The coatings were done by means of the sol-gel process. The surface structure was adjusted by annealing of the metaloxide ceramic coatings due to temperature depended crystal growth. The applied annealing temperatures were 450, 550 and 700 degrees C for 1 h, corresponding to Ra-numbers of 7, 15 and 40 nm. The surfaces were characterized by means of AFM, DTA/TG, diffractometry and white light interferometry. The cell reactions were investigated concerning adhesion kinetics, migration, spreading, cell adhesion, and collagen I synthesis. The smooth surface (Ra=7 nm) resulted in the fastest cell anchorage and cell migration. The closest cell adhesion was reached with the surface structure of Ra=15 nm. The roughest surface (Ra=40 nm) impedes the cell migration as well as a proper spreading of the cells. The best results concerning cell adhesion and spreading was reached with an intermediate surface roughness of Ra=15 nm of the niobium oxide coating on cp-titanium slices.     

Surface Modification of Biodegradable Mg-4Zn Alloy Using PMEDM: An Experimental Investigation,Optimization and Corrosion Analysis

ObjectivesMagnesium alloys are the potential candidate for metallic implants due to their excellent mechanical characteristics, biodegradable nature, and properties similar to human bone. However, a high degradation rate is primary obstacle in implementing these alloys as biodegradable orthopedic implants. Powder-mixed electric discharge machining (PMEDM) is an emerging method of surface modification of metallic alloys that can be implemented to improve the corrosion resistance of Mg alloys. Therefore, PMEDM using zirconium (Zr) and manganese (Mn) powder particles has been proposed to modify the surface characteristics of Mg-4Zn alloy.Materials and MethodsIn the present work, Zr and Mn powders have been used in varying concentrations during PMEDM of Mg-4Zn alloy. Experiments were conducted as per mixed design L18 orthogonal array (OA). Taguchi and Grey Relational Analysis (GRA) have been used to optimize the process parameters. Analysis of response characteristics, namely material removal rate (MRR), surface roughness (SR), and thickness of the alloyed layer (TAL), has been carried out at different values of input variables (like powder additives (P_a), powder concentration (C_p), peak current (I_p), pulse on time (T_on) and duty cycle (DC)). The corrosion analysis was carried out by immersing the specimen (machined at an optimized setting) in simulated body fluid (SBF).ResultsIt is observed from the analysis that C_p, I_p, and T_on play a pivotal role in evaluating response characteristics. The favorable setting suggested by the gray approach is P_a: Zr; C_p: 2 g/l; I_p: 4A; T_on: 50 μs; DC: 80%, while responses at this setting are confirmed by confirmation experiments with MRR: 32.14 mm³/min; SR: 5.578 μm and TAL: 8.28 μm. The immersion test signifies that the corrosion rate (CR) of PMEDMed sample (3.20 mm/year) is 40.74% lesser than the corrosion rate of polished sample (5.40 mm/year).ConclusionZr powder shows better performance in terms of higher MRR, lower SR and higher TAL as compared to Mn powder during the PMEDM process. The corroded surface of polished sample exhibited larger size micro pits and cracks than the machined sample, which concluded that surface modification of MZ-4Zn alloy via PMEDM is a powerful tool to enhance its corrosion resistance.     

Bioleaching of metallic sulphides withThiobacillus ferrooxidans in the absence of iron (II)

Bioleaching of metallic sulphides withThiobacillus ferrooxidans in the absence of iron (II) was studied using pure sulphides and mixtures. The direct mode of bacterial action was analysed with respect to sulphide solubility, exposed solid surfaces and bacterial attachment to the solids. Bioleaching of mixed sulphides showed enhancement of metal extraction in comparison with pure sulphides which suggests metal extractions would be better from polymetallic sulphide ores than from similar matrices with only one sulphide.     

Modification of form, material and modularity of threaded acetabulum cups]

The fixation principle of threaded cups ensures high primary stability. Inadequate results with first-generation threaded cups led to modifications of surface machining. 10 threaded cups of the first generation, and 27 of the second and third generations were systematically analysed and their shapes measured using a no-touch light section technique. In addition, measurements of surface roughness were performed. Implants of the first generation made of polyethylene, ceramic or cobalt-chrome have an average surface roughness (Ra) of 1.5 microns. Approximately one-half of these implants have a conical shape, and one-third a height that is greater than the radius. Threaded cups of the second generation are made either of CP-titanium or titanium alloy. The average corundum-blasted surface roughness is 4.5 microns. Hydroxyapatite-coated (HA) implants have a surface roughness of 5.0 microns. Approximately 45% of the implants have a conical, biconical or flattened-conical shape, while one-third are of hemispherical shape. Approximately 90% of the cups have a height that is up to 23% smaller than the radius. A few cups have a height that approximates the radius. Implants of the third generation with identical surface structure can be supplied with crosslinked-polyethylene inlays or, optionally, with metal/metal or ceramic/ceramic contact surfaces. Primary stability, biocompatible materials and a structured surface are essential for ensuring osseointegration over the long-term. Corundum-blasted pure titanium or titanium alloys with corundum-blasted or HA-coated implants can be considered standard for these cups.     

Design, construction and modularity of pressure-fit acetabular cups]

To enable a comparison of different pressfit acetabular cups objective criteria are essential. The aim of this study is to describe the design features of this type of cup and to analyse currently available cups. 30 implants were systematically measured and analysed. The mean surface roughness (Ra) was determined and configurations established with the light section technique. For further evaluation the cups were transversely sectioned. The cups are made of pure titanium, titanium alloy or polyethylene coated with titanium. Five implants take the form of monoblocks. The configuration is predominately (n = 25) flattened spherical. The size of eight cups corresponds to the outer diameter, 19 cups have a larger outer diameter (overdimensioning), 3 cups have a smaller outer diameter (underdimensioning). The magnitude of overdimensioning is, on average, 1.9%. 9 cups are provided with plugs, hollow cylinders, fins or rings as outer stabilizers. Surface roughness achieved with corundum blasting is 6.8 microns. Titanium porous-coated implants have a surface roughness of 21-32 microns. 24 cups have polyethylene inserts, most of which are snap-fixed with equatorial lips. For 16 cups, full-ceramic inserts are available. 4 cups have a metal insert. Titanium implants with structured or HAC-coated surfaces have become the accepted standard for cementless acetabular cup implantation. Together with ceramic, metal, or modified polyethylene inserts they meet the requirement for permanent osteo-integrative stability.