A histological and biomechanical study of bone stress and bone remodeling around immediately loaded implants

Immediate loading(IL)increases the risk of marginal bone loss.The present study investigated the biomechanical response of peri-implant bone in rabbits after IL,aiming at optimizing load management.Ninety-six implants were installed bilaterally into femurs of 48 rabbits.Test implants on the left side created the maximal initial stress of 6.9 and 13.4 MPa in peri-implant bone and unloaded implants on the contralateral side were controls.Bone morphology and bone-implant interface strength were measured with histological examination and push-out testing during a 12-week observation period.Additionally,the animal data were incorporated into finite element(FE)models to calculate the bone stress distribution at different levels of osseointegration.Results showed that the stress was concentrated in the bone margin and the bone stress gradually decreased as osseointegration proceeded.A stress of about 2.0 MPa in peri-implant bone had a positive effect on new bone formation,osseointegration and bone-implant interface strength.Bone loss was observed in some specimens with stress exceeding 4.0 MPa.Data indicate that IL significantly increases bone stress during the early postoperative period,but the load-bearing capacity of peri-implant bone increases rapidly with an increase of bone-implant contact.Favorable bone responses may be continually promoted when the stress in peri-implant bone is maintained at a definite level.Accordingly,the progressive loading mode is recommended for IL implants.     

A repeated sampling bone chamber methodology for the evaluation of tissue differentiation and bone adaptation around titanium implants under controlled mechanical conditions

A repeated sampling bone chamber methodology was developed for the study of the influence of the mechanical environment on skeletal tissue differentiation and bone adaptation around titanium implants. Via perforations, bone grows into the implanted outer bone chamber, containing an inner bone chamber with a central test implant. An actuator—easily mounted on the outer bone chamber—allows a controlled mechanical stimulation of the test implant. After each experiment, the inner bone chamber—with its content—can be harvested and analysed. A new inner bone chamber with a central implant can be inserted consecutively in the outer bone chamber and a new experiment can start. Pilot studies led to a reliable surgical protocol and showed the applicability of the methodology, offering the possibility to study skeletal tissue differentiation and adaptation around implants under well-controlled mechanical conditions, and this protected from external loading. Repeated sampling of the bone chamber allows conducting several experiments within the same animal at the same site, thereby excluding subject- and site-dependent variability and reducing the amount of experimental animals.     

Engineering microdent structures of bone implant surfaces to enhance osteogenic activity in MSCs

Problems persist with the integration of hip and dental implants with host bone tissues, which may result in long-term implant failure. Previous studies have found that implants bearing irregular surfaces can facilitate osseointegration. An improvement to this approach would use implant surfaces harboring a well-defined surface microstructure to decrease variability in implant surfaces. In this study, we tested whether well-defined surfaces with arrays of microdents (each with depth approximately 3 µm) significantly affected the morphology, proliferation, and osteogenic activity of mesenchymal stem cells (MSCs). Arrays of microdents tested had diameters of 9 µm, 12 µm, and 18 µm, while spacing between arrays ranged from 8 µm to 34 µm. Effects on MSC morphology (cell spreading area) and proliferation were also quantified, with both significantly decreasing on micropatterned surfaces (p<0.05) on smaller and denser microdents. In contrast, MSCs were found to deposit more calcified matrix on smaller and denser arrays of microdents. MSCs on a pattern with arrays of microdents with a diameter of 9 µm and a spacing 8 µm deposited 3–4 times more calcified matrix than on a smooth surface (p<0.05). These findings show that well-defined surface microtopographies promote osteogenic activity, which can be used on implant surfaces to improve integration with the host bone tissue.     

Influence of different mucosal resiliency and denture reline on stress distribution in peri-implant bone tissue during osseointegration. A three-dimensional finite element analysis

doi: 10.1111/j.1741‐2358.2011.00569.x Influence of different mucosal resiliency and denture reline on stress distribution in peri‐implant bone tissue during osseointegration. A three‐dimensional finite element analysis Objective: The aim of this study was to evaluate the influence of mucosal properties and relining material on the stress distribution in peri‐implant bone tissue during masticatory function with a conventional complete denture during the healing period through finite element analysis. Materials and Methods: Three‐dimensional models of a severely resorbed mandible with two recently placed implants in the anterior region were created and divided into the following situations: (i) conventional complete denture and (ii) relined denture with soft lining material. The mucosal tissue properties were divided into soft, resilient and hard. The models were exported to mechanical simulation software; two simulations were carried out with a load at the lower right canine (35 N) and the lower right first molar (50 N). Data were qualitatively evaluated using Maximum Principal Stress, in MPa, given by the software. Results: All models showed stress concentrations in the cortical bone corresponding to the cervical part of the implant. The mucosal properties influenced the stress in peri‐implant bone tissue showing a different performance according to the denture base material. The simulations with relined dentures showed lower values of stress concentration than conventional ones. Conclusions: It seems that the mucosal properties and denture reline have a high influence on the stress distribution in the peri‐implant bone during the healing period.     

Study of growth processes in bone and skin tissues in porous implants designed for fixation of external prosthesis after amputation of extremities

Modeling in vivo (on Wistar rats) was carried out by the method of complete integration of the prosthesis of an amputated extremity with a residuum; in this procedure the prosthesis is fixed to the residuum with a metal pylon one end of which is implanted into the bone of the residuum, while the other end traverses the residuum tissues and skin 5–7 cm above the residuum surface. This procedure includes not only successful implantation in the residuum bone, but also the possibility that the pores in the metal pylon can be filled with skin cells in the area of the pylon which traverses the tissues of the residiuum. The porous titanium pylon was implanted into the bone of experimental animals with amputated extremities. Penetration of bone and skin cells into the pores of the studied material was demonstrated, which provides tighter fixation in the bone and shows promise for the development of a natural cutaneous barrier to infection.     

Synchronization of estrus and fertility in goats with norgestomet ear implants

Estrus was synchronized in 64 dairy goats in July with norgestomet ear implants. Half the does received ear implants that contained 6 mg norgestomet and the remaining does received implants that contained 3 mg. Implants were left in place for 11 days. Each doe received i.m. injections of 400 IU PMSG and 50 mug cloprostenol 24 hours prior to implant removal. Twenty-eight of 32 does (87.5%) that received 6 mg or 3 mg norgestomet exhibited onset of estrus within 24 hours of implant removal. All does had exhibited onset of standing estrus by 43 hours after implant removal. Does were hand-mated to fertile bucks twice daily while in standing estrus. There were no differences between does implanted with 6 mg or 3 mg in fertility to the induced estrus (74.2% vs 75% kidding), mean length of gestation (151.0 +/- 3.2 vs 151.6 +/- 2.0 days), mean number of kids per doe (2.1 +/- 0.8 vs 2.3 +/- 0.7) or in mean kid weights (3.10 +/- 0.80 vs 3.06 +/- 0.86 kg) (6 mg vs 3 mg, respectively). It was concluded that ear implants that contained 3 mg of norgestomet were equally as effective as implants that contained 6 mg for synchronization of estrus in dairy goats.     

The frequency, growth kinetics, and osteogenic/adipogenic differentiation properties of canine bone marrow stromal cells

Bone marrow stromal cells (BMSCs) have gained considerable attention as a potential source for cell transplantation therapies for a variety of diseases due to their accessibility, proliferative capacity, and multilineage differentiation properties. Canine BMSCs have been shown to contribute to regeneration of osseous tissues, but knowledge about their biology is currently limited. In the present study, we investigated the frequency of adult canine BMSCs in bone marrow, morphological features, growth kinetics, and osteogenic as well as adipogenic differentiation properties in vitro. Our data suggest that adult canine bone marrow contains approximately one BMSC in every 2.38 × 10⁴ bone marrow mononucleated cells (0.0042 ± 0.0019%, n = 5). Primary BMSC cultures consisted of morphologically heterogeneous adherent cell populations from which spindle-shaped cells grew and became the predominant cell type. Growth kinetics patterns were dependent on the initial cell seeding densities, resulting in the highest fold increase at lower cell density. In the presence of osteogenic and adipogenic inducers, primary BMSCs underwent morphological and phenotypic changes characteristic of osteogenic and adipogenic differentiation, respectively. This study provides insights into basic characterization of adult canine BMSCs.     

Evaluation of bone remodeling around single dental implants of different lengths: a mechanobiological numerical simulation and validation using clinical data

Algorithmic models have been proposed to explain adaptive behavior of bone to loading; however, these models have not been applied to explain the biomechanics of short dental implants. Purpose of present study was to simulate bone remodeling around single implants of different lengths using mechanoregulatory tissue differentiation model derived from the Stanford theory, using finite elements analysis (FEA) and to validate the theoretical prediction with the clinical findings of crestal bone loss. Loading cycles were applied on 7-, 10-, or 13-mm-long dental implants to simulate daily mastication and bone remodeling was assessed by changes in the strain energy density of bone after a 3, 6, and 12 months of function. Moreover, clinical findings of marginal bone loss in 45 patients rehabilitated with same implant designs used in the simulation (n = 15) were computed to validate the theoretical results. FEA analysis showed that although the bone density values reduced over time in the cortical bone for all groups, bone remodeling was independent of implant length. Clinical data showed a similar pattern of bone resorption compared with the data generated from mathematical analyses, independent of implant length. The results of this study showed that the mechanoregulatory tissue model could be employed in monitoring the morphological changes in bone that is subjected to biomechanical loads. In addition, the implant length did not influence the bone remodeling around single dental implants during the first year of loading.     

Stress distribution in cylindrical and conical implants under rotational micromovement with different boundary conditions and bone properties: 3-D FEA

Factors related to micromovements at bone-implant interface have been studied because they are considered adverse to osseointegration. Simplifications are commonly observed in these FEA evaluations. The aim of this study was to clarify the influence of FEA parameters (boundary conditions and bone properties) on the stress distribution in peri-implant bone tissue when micromovements are simulated in implants with different geometries. Three-dimensional models of an anterior section of the jaw with cylindrical or conical titanium implants (4.1 mm in width and 11 mm in length) were created. Micromovement (50, 150, or 250 μm) was applied to the implant. The FEA parameters studied were linear vs. non-linear analyses, isotropic vs. orthogonal anisotropic bone, friction coefficient (0.3) vs. frictionless bone-implant contact. Data from von Mises, shear, maximum, and minimum principal stresses in the peri-implant bone tissue were compared. Linear analyses presented a relevant increase of the stress values, regardless of the bone properties. Frictionless contact reduced the stress values in non-linear analysis. Isotropic bone presented lower stress than orthogonal anisotropic. Conical implants behave better, in regard to compressive stresses (minimum principal), than cylindrical ones, except for nonlinear analyses when micromovement of 150 and 250 μm were simulated. The stress values raised as the micromovement amplitude increased. Non-linear analysis, presence of frictional contact and orthogonal anisotropic bone, evaluated through maximum and minimum principal stress should be used as FEA parameters for implant-micromovement studies.     

Aspiration and cytological evaluation of idiopathic bone cavities of the jaw

The idiopathic bone cavity (IBC) is an intraosseous pseudocyst devoid of epithelial lining. Clinically, IBCs of the jaw are asymptomatic and normally found in routine radiographic exams. Although the literature regarding the content of IBCs is controversial, the final diagnosis is usually aided by the discovery of an empty cavity upon surgical exploration. The aim of this study was to perform cytological and histological analysis of IBC contents. Cytological analysis of nine cases of IBC was performed after puncture and processed by the cell block technique. Histological analysis was performed in six cases in which it was possible to collect enough material by curettage of bone walls. Remarkably, cell block analysis revealed the presence of fibrin, often arranged as a net; erythrocytes; and inflammatory cells, with a predominance of lymphocytes as well as some macrophages and neutrophils. Histological analysis showed the presence of scant connective tissue, bone trabeculae, hemorrhagic foci, and hemosiderin. Only two cases presented scattered multinucleated giant cells. Cytological evaluation of IBC content by the cell block technique might represent a useful diagnostic tool, especially in cases in which there is no available material for curettage in the cavity.     

Preparation and characterization of cockle shell aragonite nanocomposite porous 3D scaffolds for bone repair

The demands for applicable tissue-engineered scaffolds that can be used to repair load-bearing segmental bone defects (SBDs) is vital and in increasing demand. In this study, seven different combinations of 3 dimensional (3D) novel nanocomposite porous structured scaffolds were fabricated to rebuild SBDs using an extraordinary blend of cockle shells (CaCo₃) nanoparticles (CCN), gelatin, dextran and dextrin to structure an ideal bone scaffold with adequate degradation rate using the Freeze Drying Method (FDM) and labeled as 5211, 5400, 6211, 6300, 7101, 7200 and 8100. The micron sized cockle shells powder obtained (75 µm) was made into nanoparticles using mechano-chemical, top-down method of nanoparticles synthesis with the presence of the surfactant BS-12 (dodecyl dimethyl bataine). The phase purity and crystallographic structures, the chemical functionality and the thermal characterization of the scaffolds’ powder were recognized using X-Ray Diffractometer (XRD), Fourier transform infrared (FTIR) spectrophotometer and Differential Scanning Calorimetry (DSC) respectively. Characterizations of the scaffolds were assessed by Scanning Electron Microscopy (SEM), Degradation Manner, Water Absorption Test, Swelling Test, Mechanical Test and Porosity Test. Top-down method produced cockle shell nanoparticles having averagely range 37.8±3–55.2±9 nm in size, which were determined using Transmission Electron Microscope (TEM). A mainly aragonite form of calcium carbonate was identified in both XRD and FTIR for all scaffolds, while the melting (Tm) and transition (Tg) temperatures were identified using DSC with the range of Tm 62.4–75.5 °C and of Tg 230.6–232.5 °C. The newly prepared scaffolds were with the following characteristics: (i) good biocompatibility and biodegradability, (ii) appropriate surface chemistry and (iii) highly porous, with interconnected pore network. Engineering analyses showed that scaffold 5211 possessed 3D interconnected homogenous porous structure with a porosity of about 49%, pore sizes ranging from 8.97 to 337 µm, mechanical strength 20.3 MPa, Young's Modulus 271±63 MPa and enzymatic degradation rate 22.7 within 14 days.     

Ultrastructural and lanthanum tracer examination of rapidly resorbing rat alveolar bone suggests that osteoclasts internalize dying bone cells

Glutaraldehyde-formaldehyde fixed undecalcified alveolar bone from 7-day-old rats was prepared for light and electron microscopy. Colloidal lanthanum was used as an ultrastructural tracer, and both random and semi-serial sections were examined. Lanthanum penetrated the infoldings of the ruffled border and some nearby vacuoles and vesicles. The majority of vacuoles and vesicles were lanthanum-free. Some osteoclast profiles contained a large vacuole with a cell enclosed in its interior. The enclosed cell exhibited an irregular nucleus containing condensed peripheral chromatin, intact cytoplasmic organelles, conspicuous rough endoplasmic reticulum and large blebs on the cell surface. These features are characteristic of osteoblasts or bone-lining cells or immature osteocytes which may be undergoing apoptosis or necrosis. The observation of remnants of cellular structures within internalized osteoclast vacuoles, together with the above results, suggests that osteoclasts engulf and probably degrade dying osteoblasts/bone-lining cells or immature osteocytes. Received: 29 April 1997 / Accepted: 20 February 1998     

Histological techniques and microscopic analysis of biological agents for preservation of human bone remains

Microscopy and histology techniques can be applied to morphological study of fungi and bacteria contaminating ancient human osteological remains. Undecalcified samples are cut with a diamond rotary blade microtome and an original technique was applied using adhesive tape to prevent damage to the bone surface during sectioning. We used light microscopy, polarized light microscopy, and epi-illumination fluorescence systems. Common dyes can be applied to 80 μm sections using classic staining techniques to reveal the architecture of bone and the presence of infecting biological agents.     

Bone morphogenetic protein signaling through ACVR1 and BMPR1A negatively regulates bone mass along with alterations in bone composition

Bone quantity and bone quality are important factors in determining the properties and the mechanical functions of bone. This study examined the effects of disrupting bone morphogenetic protein (BMP) signaling through BMP receptors on bone quantity and bone quality. More specifically, we disrupted two BMP receptors, Acvr1 and Bmpr1a, respectively, in Osterix-expressing osteogenic progenitor cells in mice. We examined the structural changes to the femora from 3-month old male and female conditional knockout (cKO) mice using micro-computed tomography (micro-CT) and histology, as well as compositional changes to both cortical and trabecular compartments of bone using Raman spectroscopy. We found that the deletion of Acvr1 and Bmpr1a, respectively, in an osteoblast-specific manner resulted in higher bone mass in the trabecular compartment. Disruption of Bmpr1a resulted in a more significantly increased bone mass in the trabecular compartment. We also found that these cKO mice showed lower mineral-to-matrix ratio, while tissue mineral density was lower in the cortical compartment. Collagen crosslink ratio was higher in both cortical and trabecular compartments of male cKO mice. Our study suggested that BMP signaling in osteoblast mediated by BMP receptors, namely ACVR1 and BMPR1A, is critical in regulating bone quantity and bone quality.     

Numerical and experimental evaluation of TPMS Gyroid scaffolds for bone tissue engineering

The combination of computational methods with 3D printing allows for the control of scaffolds microstructure. Lately, triply periodic minimal surfaces (TPMS) have been used to design porosity-controlled scaffolds for bone tissue engineering (TE). The goal of this work was to assess the mechanical properties of TPMS Gyroid structures with two porosity levels (50 and 70%). The scaffold stiffness function of porosity was determined by the asymptotic homogenisation method and confirmed by mechanical testing. Additionally, microCT analysis confirmed the quality of the printed parts. Thus, the potential of both design and manufacturing processes for bone TE applications is here demonstrated.     

The biomechanical analysis of bone strength: A method and its application to platycnemia

Traditional methods of bone analysis (both metric and topographic) are restricted to external characters. Spacial distribution of material is, however, equally critical to an understanding of a bone's function. Dynamic testing to determine whole bone strength can only be performed on fresh specimens. Methods for the calculation of both bending and torsional strength of other specimens (such as preserved or fossil bones) are developed in this paper. In order to illustrate the methods, the functional significance of tibial shaft cross sectional variation is investigated.     

Development and design of a novel loading device for the investigation of bone adaptation around immediately loaded dental implants using the reindeer antler as implant bed

The assessment of the behavior of immediately loaded dental implants using biomechanical methods is of particular importance. The primary goal of this investigation is to optimize the function of the implants to serve for immediate loading. Animal experiments on reindeer antlers as a novel animal model will serve for investigation of the bone remodeling processes in the implant bed. The main interest is directed towards the time and loading-dependant behavior of the antler tissue around the implants. The aim and scope of this work was to design an autonomous loading device that has the ability to load an inserted implant in the antler with predefined occlusal forces for predetermined time protocols. The mechanical part of the device can be attached to the antler and is capable of cyclically loading the implant with forces of up to 100 N. For the calibration and testing of the loading device a biomechanical measuring system has been used. The calibration curve shows a logarithmic relationship between force and motor current and is used to control the force on the implant. A first test on a cast reindeer antler was performed successfully.     

Experimental bone defect healing with xenogenic demineralized bone matrix and bovine fetal growth plate as a new xenograft: radiological, histopathological and biomechanical evaluation

The following study was designed to evaluate xenogenic bovine demineralized bone matrix (DBM) and new xenograft (Bovine fetal growth plate) effects on bone healing process. Twenty male White New Zealand rabbits were used in this study. In group I (n = 10) the defect was filled by xenogenic DBM and in group II (n = 10) the defect was filled by a segment of bovine fetal growth plate and was fixed by cercelage wire. Radiological, histopathological, and biomechanical evaluations were performed blindly and results scored and analyzed statistically. Statistical tests did not support significant differences between two groups radiographically (P > 0.05). There was a significant difference for union at the 28nd postoperative radiologically (P < 0.05). Xenograft was superior to DBM group at the 28th postoperative day for radiological union (P < 0.03). Histopathological and biomechanical evaluation revealed no significant differences between two groups. In conclusion, the results of this study indicate that satisfactory healing occurred in rabbit radius defect filled with xenogenic bovine DBM and xenogenic bovine fetal growth plate. Complications were not identified and healing was faster in two grafting groups.     

The Italian multicentre dosimetric study for lesion dosimetry in 223Ra therapy of bone metastases: Calibration protocol of gamma cameras and patient eligibility criteria

PurposeThe aims of this work were to explore patient eligibility criteria for dosimetric studies in ²²³Ra therapy and evaluate the effects of differences in gamma camera calibration procedures into activity quantification.MethodsCalibrations with ²²³Ra were performed with four gamma cameras (3/8-inch crystal) acquiring planar static images with double-peak (82 and 154 keV, 20% wide) and MEGP collimator. The sensitivity was measured in air by varying activity, source-detector distance, and source diameter. Transmission curves were measured for attenuation/scatter correction with the pseudo-extrapolation number method, varying the experimental setup. ²²³Ra images of twenty-five patients (69 lesions) were acquired to study the lesions visibility. Univariate ROC analysis was performed considering visible/non visible lesions on ²²³Ra images as true positive/true negative group, and using as score value the lesion/soft tissue contrast ratio (CR) derived from ^99mTc-MDP WB scan.ResultsSensitivity was nearly constant varying activity and distance (maximum s.d. = 2%). Partial volume effects were negligible for object area ⩾960 mm². Transmission curve measurements are affected by experimental setup and source size, leading to activity quantification errors up to 20%. The ROC analysis yielded an AUC of 0.972 and an optimal threshold of CR of 10, corresponding to an accuracy of 92%.ConclusionThe minimum calibration protocol requires sensitivity and transmission curve measurements varying the object size, performing a careful procedure standardisation. Lesions with ^99mTc-MDP CR higher than 10, not overlapping the GI tract, are generally visible on ²²³Ra images acquired at 24 h after the administration, and possibly eligible for dosimetric studies.