Production of extracellular protease from crude substrates with dregs in an external-loop airlift bioreactor with lower ratio of height to diameter

Bacillus subtilis AS1.398 was cultivated in a 11.5-L total volume external-loop airlift bioreactor with a low height-to-diameter ratio of 2.9 and a riser-to-downcomer diameter ratio of 6.6 for the production of protease from crude substrates with dregs. The influence of aeration rate, liquid volume, and sparger hole diameter on protease production was investigated. An average of 8197 u/mL protease activity was obtained after a total fermentation time of 32 h in the external-loop airlift bioreactor with a liquid volume of 8.5 L, air flow rate of 1.5 vvm, and sparger hole diameter of 1.5 mm. The addition of one stainless steel sieve plate in the riser of the airlift bioreactor increased productivity of protease. After 32 h of fermentation, an average of 8718 u/mL protease activity was achieved in the external-loop airlift bioreactor with one sieve plate and an air flow rate of 1.2 vvm, liquid volume of 8.5 L, and gas sparger hole diameter of 1.5 mm. This was 9.0% higher than the typical averages of about 8000 u/mL protease activity in the mechanically stirred tank bioreactors of the enzyme factory using the same microorganism. It is possible to make a scale-up of the external-loop airlift bioreactor and feasible to operate it for production of protease from crude substrate with dregs.     

Investigation of the bacitracin biosynthesis in an airlift bioreactor

Results of pilot plant studies using an external-loop airlift bioreactor (170 l fermentation volume, liquid height-to-riser diameter: 27, loop-to-tower cross-section-area: 0.1225) have proven the relative merits of such a system in the bacitracin biosynthesis produced by the Bacillus licheniformis submerged aerobic cultivation. The results were compared to those obtained in a pilot-scale stirred-tank bioreactor with the same values of k_La. Excepting the aeration rate of 0.2 vvm, the fermentation process performed at 0.5 vvm and 1/0 vvm, respectively, unfolded similarly in the two fermentation devices with respect to the cell mass production, substrate utilization and bacitracin production during the fermentation process. In the riser section of the airlift bioreactor, the dissolved oxygen levels were higher, while in the downcomer section they were lower than those realized in the stirred tank bioreactor. Power requirements of the airlift fermenter were by 17–64% lower than those for a mechanically agitated system, depending on the aeration rates, which led to an important energy saving. Moreover, the lack of mechanical devices in the airlift system provides safety and a more gentle environment for the cultivation of microorganisms.     

Microbial biomass production from rice straw hydrolysate in airlift bioreactors

Rice straw is a by-product of rice production, and a great bioresource as raw biomass material for manufacturing value-adding protein for animal feedstock, which has been paid more and more attention. In the present work, utilizing rice straw hydrolysate as a substrate for microbial biomass production in 11.5L external-loop airlift bioreactors was investigated. Rice straw hydrolysate obtained through acid-hydrolyzing rice straw was used for the culture of yeast Candida arborea AS1.257. The influences of gas flow rate, initial liquid volume, hole diameter of gas sparger and numbers of sieve plates on microbial biomass production were examined. The best results in the external-loop airlift bioreactor were obtained under 9.0 L initial liquid volume, 1.1 (v/v)/min gas flow rate during culture time of 0-24 h and 1.4 (v/v)/min gas flow rate of 24-48 h at 29+/-1 degrees C. The addition of the sieve plates in the riser of the external-loop airlift bioreactor increased productivity. After 48 h, under optimized operation conditions, crude protein productivity with one sieve and two sieves were 13.6 mg/mL and 13.7 mg/mL, respectively, comparing 12.7 mg/mL without sieves in the airlift bioreactor and 11.7 mg/mL in the in the 10-L mechanically stirred tank bioreactor. It is feasible to operate the external-loop airlift bioreactors and possible to reduce the production cost for microbial biomass production from the rice straw hydrolysate.     

Production of xylanolytic enzymes by <Emphasis Type="Italic">Aspergillus terricola</Emphasis> in stirred tank and airlift tower loop bioreactors

Fungi producing high xylanase levels have attracted considerable attention because of their potential industrial applications. Batch cultivations of Aspergillus terricola fungus were evaluated in stirred tank and airlift bioreactors, by using wheat bran particles suspended in the cultivation medium as substrate for xylanase and β-xylosidase production. In the stirred tank bioreactor, in physical conditions of 30°C, 300 rpm, and aeration of 1 vvm (1 l min⁻¹), with direct inoculation of fungal spores, 7,475 U l⁻¹ xylanase was obtained after 36 h of operation, remaining constant after 24 h. In the absence of air injection in the stirred tank reactor, limited xylanase production was observed (final concentration 740 U l⁻¹). When the fermentation process was realized in the airlift bioreactor, xylanase production was higher than that observed in the stirred tank bioreactor, being 9,265 U l⁻¹ at 0.07 vvm (0.4 l min⁻¹) and 12,845 U l⁻¹ at 0.17 vvm (1 l min⁻¹) aeration rate.     

Investigation of acid proteinase biosynthesis by the fungus Humicola lutea 120-5 in an airlift bioreactor

Acid proteinase production using filamentous fungus Humicola lutea 120-5 was studied under batch and continuous fermentation conditions in an airlift bioreactor. A comparison with proteinase production by fungal cells, cultivated in stirred tank bioreactor was made. The process performance in both fermentation devices was similar with respect to substrate utilization, biomass, and enzyme concentration. Continuous acid proteinase production was achieved for 14 days at an optimal dilution rate of 0.05/h with maximum specific activity of 90 U/mg DW of mycelia and yield of 38 U/mg glucose. The volumetric productivity (50 U/ml. h) was approximately 3 times higher than this of the batch system. All continuous experiments were carried out without any bacterial contamination, due to the low pH (3.0-3.5) during the process. The "pellet" type growth of the fungus in the airlift reactor prevented the system from plugging with filaments.     

Cultivation of a filamentous mould in an airlift bioreactor

Cephalosporin C biosynthesis was investigated in a pilot-plant external-loop airlift bioreactor for evaluating the capacity of this bioreactor to surpass the problems which arise from the morphology of the mould and the rheology of the broth. Some of the results were compared with those obtained in a stirred tank bioreactor. The dilution and the use of static mixers was necessary to overcome the effects of the high viscosities. The oxygen transfer rate represented 84% of that in the stirred bioreactor, but the efficiency of the power utilization was higher. The specific productivity of Cephalosporin C is comparable to that obtained in the stirred tank bioreactor, but the average specific power consumption was found to be 2/3 of that in the stirred vessel.     

Cultivation of transgenicNicotiana tabacum suspension cells in bioreactors for the production of mGM-CSF

TransgenicNicotiana tabacum cells were cultivated for the production of murine granulocyte macrophage-colony stimulating factor (mGM-CSF) in both a stirred, tank biore|actor and an airlift bioreactor with draft tube. Cell growth and mGM-CSF production in the airlift bioreactor were found to be better than those achieved in the stirred tank bioreactor. In the airlift bioreactor. 9.0 g/L of cells and 2.2 ng/mL of mGM-CSF were obtained (11.0 g/L and 2.4 ng/mL, respectively in shake flasks). Although the lag period was prolonged and mGM-CSF production was lowered by 33% in the stirred tank bioreactor as compared to the control culture, the maximum cell density was increased up to 12.0 g/L due to better mixing by agitation at the higher cell density.     

麦芽糖诱导软化芽孢杆菌α-环糊精葡萄糖基转移酶在枯草杆菌中的表达

通过PCR扩增软化芽孢杆菌α-环糊精葡萄糖基转移酶基因,将基因片段克隆到大肠杆菌-枯草杆菌穿梭载体pGJ103中,转化枯草杆菌WB600得基因工程菌进行外源表达。在1.5%的麦芽糖初始发酵培养基上摇瓶培养,48 h后重组枯草杆菌产酶活性为6.1U/ml。通过单因素分析和响应面分析对重组枯草杆菌产CGT酶摇瓶发酵条件进行优化。分析得到培养基关键组分麦芽糖,玉米淀粉和酵母粉三者最佳浓度分别为:15.5g/L,13g/L和20g/L。在此条件下,摇瓶培养36h后α-CGT酶活性为17.6U/ml,5L罐分批发酵30h后酶活达到20U/ml (水解活性为1.4×10⁴ IU/ml)。     

Thermostable lipolytic enzymes production in batch and continuous cultures of Thermus thermophilus HB27

Several studies in laboratory-scale bioreactors are undertaken in order to verify the beneficial effect of thermal spring water in the culture medium of Thermus thermophilus HB27. Two bioreactor configurations, stirred tank and airlift, are investigated to determine the most suitable one to develop a continuous process. Water mineral composition affects the lipolytic enzyme secretion and growth of T. thermophilus HB27 in both bioreactor configurations. Furthermore, the lipolytic activity is strongly enhanced when stirred tank bioreactor is used. Moreover, operation in a stirred tank at an agitation rate of 650 rpm leads to the highest total lipolytic activity (intra- and extracellular enzyme) around 280 U/L after 32 h. Continuous cultures operating in the optimised conditions determined in batch cultures are carried out. It is noticeable that the stirred tank bioreactor was able to operate in a continuous flow mode without operational problems. In addition, the lipolytic activity obtained is about 2-fold higher than that attained in batch cultures.     

溶氧对Blakeslea trispora分批发酵生产β-胡萝卜素的影响

在摇瓶和5 L发酵罐中研究了溶氧 (DO) 对Blakeslea trispora分批发酵生产β-胡萝卜素的影响,总结了5 L发酵罐中β-胡萝卜素发酵过程中溶氧的变化规律.结果表明,当500 mL摇瓶装液量为50 mL,转速为240 r/min条件下发酵生产β-胡萝卜素产量最大,达到3.416 g/L; 5 L发酵罐中,在搅拌转速为1 000 r/min,通气量为1.5 vvm的条件下,β-胡萝卜素的产量可达到3.712 g/L,略高于摇瓶,这可能是由于5 L发酵罐中的气液传递和混合状况好于摇瓶,促进了产物的合成.     

Optimization of medium and process parameters for the production of inulinase from a newly isolated Kluyveromyces marxianus YS-1

A newly isolated strain of Kluyveromyces marxianus YS-1 was used for the production of extra cellular inulinase in a medium containing inulin, meat extract, CaCl2 and sodium dodecyl sulphate (SDS). Fermentation medium pH 6.5, cultivation temperature 30 degrees C and 5% (v/v) inoculum of 12 h-old culture were optimal for enzyme production (30.8 IU/ml) with a fermentation time of 72 h at shake flask level. Raw inulin (2%, w/v) extracted from dahlia tubers by processing at 15 kg/cm2 for 10 min was optimum for bioreactor studies. Maximum enzyme production (55.4 IU/ml) was obtained at an agitation rate of 200 rpm and aeration of 0.75 vvm in a stirred tank reactor with a fermentation time of 60 h.     

Application of an airlift bioreactor to the nystatin biosynthesis

Pilot plant studies were performed using a concentric-tube airlift bioreactor of 2.5 m³ fermentation volume. The results have proven the relative merits of such a system in the biosynthesis of nystatin, produced by Streptomyces noursei, in submerged aerobic cultivation and batch operation mode. The results were compared to those obtained in a pilot-scale stirred tank bioreactor of 3.5 m³ fermentation volume. The fermentation processes in the two fermentation devices were similar with respect to substrate utilization, biomass production and nystatin biosynthesis. In the riser section, the dissolved oxygen concentration was higher than that in the downcomer. The volumetric oxygen mass transfer coefficient was dependent on the rheological behaviour of the biosynthesis liquids, which was not constant during the fermentation process. The total energy consumption for nystatin production in the airlift bioreactor was 56% of that in the stirred tank, while the operating costs represented 78% of those in the stirred tank bioreactor.     

Monoterpenoid oxindole alkaloid production by Uncaria tomentosa (Willd) D.C. cell suspension cultures in a stirred tank bioreactor

Cell growth, monoterpenoid oxindole alkaloid (MOA) production, and morphological properties of Uncaria tomentosa cell suspension cultures in a 2-L stirred tank bioreactor were investigated. U. tomentosa (cell line green Uth-3) was able to grow in a stirred tank at an impeller tip speed of 95 cm/s (agitation speed of 400 rpm), showing a maximum biomass yield of 11.9 +/- 0.6 g DW/L and a specific growth rate of 0.102 d(-1). U. tomentosa cells growing in a stirred tank achieved maximum volumetric and specific MOA concentration (467.7 +/- 40.0 microg/L, 44.6 +/- 5.2 microg/g DW) at 16 days of culture. MOA chemical profile of cell suspension cultures growing in a stirred tank resembled that of the plant. Depending on culture time, from the total MOA produced, 37-100% was found in the medium in the bioreactor culture. MOA concentration achieved in a stirred tank was up to 10-fold higher than that obtained in Erlenmeyer flasks (agitated at 110 rpm). In a stirred tank, average area of the single cells of U. tomentosa increased up to 4-fold, and elliptical form factor increased from 1.40 to 2.55, indicating enlargement of U. tomentosa single cells. This work presents the first report of U. tomentosa green cell suspension cultures that grow and produce MOA in a stirred tank bioreactor.     

Cultivation of a filamentous mold in a glass pilot-scale airlift fermentor

Results of pilot plant studies using a glass airlift fermentation device (55 liter fermentation volume) have proven the relative merits of such a system in the fermentation of a filamentous mold, Monascus purpureus, on 4% (w/w) starch media. The resultant overall yield of cell mass (Y_x/s) of 0.38 was an appreciable increase over the 0.32 obtained with a pilot scale stirred tank fermentor previously studied. Power requirements of the airlift fermentor were approximately 50% of those for the mechanically agitated system. The lack of mechanical shear in the airlift system provides a more gentle environment or the cultivation of organisms than does the high degree of shear prevalent in the mechanically agitated vessels. Mass transfer of oxygen to the aqueous phase of the fermentation volume is improved significantly through use of the airlift device. Mass transfer coefficients in the range of 200 reciprocal hr were obtained to approximately 80 reciprocal hr in the stirred tank fermentor.     

Effect of shear stress on anthraquinones production by Rubia tinctorum suspension cultures

Suspension cultures of Rubia tinctorum, an anthraquinones (AQs) producer, were grown both in Erlenmeyer flasks at 100 rpm and in a 1.5 L mechanically stirred tank bioreactor operating at 450 rpm. The effect of hydrodynamic stress on cell viability, biomass, and AQs production was evaluated. Cell viability showed a transient decrease in the bioreactor during the first days, returning to the initial values toward the end of the culture time. The biomass obtained in the bioreactor was 29% lower than that attained in the Erlenmeyer flasks. The H2O2 production in the bioreactor (with peaks at 7 and 10 days) was about 15 times higher than that obtained in the flasks. A clear relationship exists between the maximum concentration of H2O2 generated and AQs produced. The AQs content in the bioreactor was 233% higher than that in the Erlenmeyer flasks. The AQs specific productivity in the stirred tank and in the Erlenmeyer flasks was 70.7 and 28.5 micromol/g FW/day, respectively. This production capability was maintained in the regrowth assays. On the other hand, the negative effects of hydrodynamic stress on viability and biomass concentration observed in the bioreactor culture were reverted in the regrowth cultures. It can be concluded that R. tinctorum suspension cultures are able to grow in stirred tanks at 450 rpm responding to the hydrodynamic stress with higher concentrations of AQs, which suggest the possibility of a technological approach taking advantage of this phenomenon.     

Enhancement of oxygen transfer in highly viscous non-newtonian fermentation broths

The influence of short draft tubes covered by perforated plates on gas-liquid mass transfer was examined in external-loop airlift bioreactors. The volumetric mass transfer coefficients in a model external-loop airlift bioreactor were measured with water and non-Newtonian media. It was found that introduction of draft tubes covered with perforated plates in the riser significantly improved the mass transfer rate, particularly in higher viscous non-Newtonian fermentation media. The enhancement of mass transfer rate might be due mainly to an increase in bubble coalescence and redispersion. (c) 1994 John Wiley & Sons, Inc.     

Process modeling of in situ-adsorption of a bacterial lipase

In situ adsorption, known as an in situ-roduct removal (ISPR) technique for low molecular mass bioproducts, was in this study applied to a bacterial exoenzyme proving that this method is also suitable for the separation of macromolecules like proteins. For this, adsorbent particles were added to growing cultures of Staphylococcus carnosus rec., therefore both production and adsorption occurred simultaneously in shaking flasks, stirred tank, or airlift bioreactor as the chosen types of fermenters. The exoenzyme lipase adsorbed rapidly and, after separating cells and adsorbents, desorbed in a packed bed column. Up to 85% of the produced lipase were recovered, fractions of these had been concentrated up to the factor 20 and purified up to a factor of 40 by the procedure. By using the airlift bioreactor an enhancement of biomass production was observed, but the necessity of the addition of an anti-foam reagent resulted in higher product losses in adsorption as well as in desorption. Production and adsorption kinetics have been modeled and applied to in situ-adsorption. The model was used to perform a parameter study in which the influence of biological and physical parameters as well as process parameters on discontinuous and continuous in situ-adsorption was investigated.     

Production of carbonyl reductase by Metschnikowia koreensis

A new strain of the yeast Metschnikowia koreensis was grown in shake flasks and a stirred bioreactor for the production of carbonyl reductase. The optimal conditions in the bioreactor for maximizing the biomass specific activity of the enzyme were found to be: a medium composed of glucose (20 g/L), peptone (5 g/L), yeast extract (5 g/L) and zinc sulfate (0.3g/L); the pH controlled at 7; the temperature controlled at 25 °C; an agitation speed of 500 rpm; and an aeration rate of 0.25 vvm. In the bioreactor, a biomass specific enzyme activity of 115.6 U/gDCW was obtained and the maximum biomass concentration was 15.3 gDCW/L. The biomass specific enzyme activity obtained in the optimized bioreactor culture was 11-fold higher than the best result achieved in shake flasks. The bioreactor culture afforded a 2.7-fold higher biomass concentration than could be attained in shake flasks.     

鸟苷发酵条件的优化研究

以枯草芽孢杆菌(Bacillus subtilis)TA208为供试菌株,运用单因素实验方法进行了摇瓶条件下发酵培养基以及发酵条件的优化研究,在最优发酵条件下鸟苷产量达到19．79g／L,比基本培养条件提高32．37％。     

采用玉米秸秆水解糖和玉米浆发酵生产丁二酸

研究了以玉米秸秆水解糖为碳源,不同氮源条件下琥珀酸放线杆菌Actinobacillus succinogenesSF-9的丁二酸发酵产酸能力。结果表明玉米浆可以替代酵母膏作为丁二酸发酵的廉价氮源。厌氧摇瓶丁二酸发酵单因素试验,得到在初糖浓度50 g/L时,玉米浆的较佳用量为20 g/L。在5 L搅拌罐上,考察了不同初始玉米秸秆水解糖浓度对A.succinogenes SF-9发酵生产丁二酸的影响,结果显示高初始秸秆糖浓度对琥珀酸放线杆菌的生长有抑制作用。采用补料分批发酵,发酵60 h丁二酸的产量达到42.7g/L,丁二酸产率82.7%,生产强度0.81 g/(L·h)。丁二酸的产量和生产强度较分批发酵有明显提高。